Merge tag 'pinctrl-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This is the bulk of pin control changes for the v4.9 cycle.

  General improvements:

   - nicer debugfs output with one pin/config pair per line.

   - continued efforts to strictify module vs bool.

   - constification and similar from Coccinelle engineers.

   - return error from pinctrl_bind_pins()

   - pulling in the ability to selectively disable mapping of unusable
     IRQs from the GPIO subsystem.

  New drivers:

   - new driver for the Aspeed pin controller family: AST2400 (G4) and
     AST2500 (G5) are supported. These are used by OpenBMC on the IBM
     Witherspoon platform.

   - new subdriver for the Allwinner sunxi GR8.

  Driver improvements:

   - drop default IRQ trigger types assigned during IRQ mapping on AT91
     and Nomadik. This error was identified by improvements in the IRQ
     core by Marc Zyngier.

   - active high/low types on the GPIO IRQs for the ST pin controller.

   - IRQ support on GPIOs on the STM32 pin controller.

   - Renesas Super-H/ARM sh-pfc: continued massive developments.

   - misc MXC improvements.

   - SPDIF on the Allwiner A31 SoC

   - IR remote and SPI NOR flash, NAND flash, I2C pins on the AMLogic
     SoC.

   - PWM pins on the Meson.

   - do not map unusable IRQs (taken by BIOS) on the Intel Cherryview.

   - add GPIO IRQ wakeup support to the Intel driver so we can wake up
     from button pushes.

  Deprecation:

   - delete the obsolete STiH415/6 SoC support"

* tag 'pinctrl-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
  pinctrl: qcom: fix masking of pinmux functions
  pinctrl: intel: Configure GPIO chip IRQ as wakeup interrupts
  pinctrl: cherryview: Convert to use devm_gpiochip_add_data()
  pinctrl: cherryview: Do not add all southwest and north GPIOs to IRQ domain
  gpiolib: Make it possible to exclude GPIOs from IRQ domain
  pinctrl: nomadik: don't default-flag IRQs as falling
  pinctrl: st: Remove obsolete platforms from pinctrl-st dt doc
  pinctrl: st: Remove STiH415/6 SoC pinctrl driver support.
  pinctrl: amlogic: gxbb: add i2c pins
  pinctrl: amlogic: gxbb: add nand pins
  pinctrl: stm32: add IRQ_DOMAIN_HIERARCHY dependency
  pinctrl: amlogic: gxbb: add spi nor pins
  pinctrl: sh-pfc: r8a7794: Implement voltage switching for SDHI
  pinctrl: sh-pfc: r8a7791: Implement voltage switching for SDHI
  pinctrl: sh-pfc: Add PORT_GP_24 helper macro
  pinctrl: Fix "st,syscfg" definition for STM32 pinctrl
  driver: base: pinctrl: return error from pinctrl_bind_pins()
  pinctrl: meson-gxbb: add the missing SDIO interrupt pin
  pinctrl: aspeed: fix regmap error handling
  pinctrl: mediatek: constify gpio_chip structures
  ...

7 files changed, 102 insertions, 20 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index 69617220c5d6..1685821eea41 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -23,6 +23,7 @@ Required properties:
   "allwinner,sun8i-h3-pinctrl"
   "allwinner,sun8i-h3-r-pinctrl"
   "allwinner,sun50i-a64-pinctrl"
+  "nextthing,gr8-pinctrl"
 
 - reg: Should contain the register physical address and length for the
   pin controller.
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
new file mode 100644
index 000000000000..5e60ad18f147
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
@@ -0,0 +1,65 @@
+Aspeed Pin Controllers
+----------------------
+
+The Aspeed SoCs vary in functionality inside a generation but have a common mux
+device register layout.
+
+Required properties:
+- compatible : Should be any one of the following:
+		"aspeed,ast2400-pinctrl"
+		"aspeed,g4-pinctrl"
+		"aspeed,ast2500-pinctrl"
+		"aspeed,g5-pinctrl"
+
+The pin controller node should be a child of a syscon node with the required
+property:
+- compatible: "syscon", "simple-mfd"
+
+Refer to the the bindings described in
+Documentation/devicetree/bindings/mfd/syscon.txt
+
+Subnode Format
+--------------
+
+The required properties of child nodes are (as defined in pinctrl-bindings):
+- function
+- groups
+
+Each function has only one associated pin group. Each group is named by its
+function. The following values for the function and groups properties are
+supported:
+
+aspeed,ast2400-pinctrl, aspeed,g4-pinctrl:
+
+ACPI BMCINT DDCCLK DDCDAT FLACK FLBUSY FLWP GPID0 GPIE0 GPIE2 GPIE4 GPIE6 I2C10
+I2C11 I2C12 I2C13 I2C3 I2C4 I2C5 I2C6 I2C7 I2C8 I2C9 LPCPD LPCPME LPCSMI MDIO1
+MDIO2 NCTS1 NCTS3 NCTS4 NDCD1 NDCD3 NDCD4 NDSR1 NDSR3 NDTR1 NDTR3 NRI1 NRI3
+NRI4 NRTS1 NRTS3 PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 RGMII1 RMII1 ROM16
+ROM8 ROMCS1 ROMCS2 ROMCS3 ROMCS4 RXD1 RXD3 RXD4 SD1 SGPMI SIOPBI SIOPBO TIMER3
+TIMER5 TIMER6 TIMER7 TIMER8 TXD1 TXD3 TXD4 UART6 VGAHS VGAVS VPI18 VPI24 VPI30
+VPO12 VPO24
+
+aspeed,ast2500-pinctrl, aspeed,g5-pinctrl:
+
+GPID0 GPID2 GPIE0 I2C10 I2C11 I2C12 I2C13 I2C14 I2C3 I2C4 I2C5 I2C6 I2C7 I2C8
+I2C9 MAC1LINK MDIO1 MDIO2 OSCCLK PEWAKE PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7
+RGMII1 RGMII2 RMII1 RMII2 SD1 SPI1 TIMER4 TIMER5 TIMER6 TIMER7 TIMER8
+
+Examples:
+
+syscon: scu@1e6e2000 {
+	compatible = "syscon", "simple-mfd";
+	reg = <0x1e6e2000 0x1a8>;
+
+	pinctrl: pinctrl {
+		compatible = "aspeed,g4-pinctrl";
+
+		pinctrl_i2c3_default: i2c3_default {
+			function = "I2C3";
+			groups = "I2C3";
+		};
+	};
+};
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices.
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt
index 26bcb18f4e60..013c675b5b64 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt
@@ -30,8 +30,7 @@ Second type has a dedicated interrupt per gpio bank.
 
 Pin controller node:
 Required properties:
-- compatible	: should be "st,<SOC>-<pio-block>-pinctrl"
-	like st,stih415-sbc-pinctrl, st,stih415-front-pinctrl and so on.
+- compatible	: should be "st,stih407-<pio-block>-pinctrl"
 - st,syscfg		: Should be a phandle of the syscfg node.
 - st,retime-pin-mask	: Should be mask to specify which pins can be retimed.
 	If the property is not present, it is assumed that all the pins in the
@@ -50,7 +49,11 @@ Optional properties:
 GPIO controller/bank node.
 Required properties:
 - gpio-controller : Indicates this device is a GPIO controller
-- #gpio-cells	  : Should be one. The first cell is the pin number.
+- #gpio-cells	  : Must be two.
+     - First cell: specifies the pin number inside the controller
+     - Second cell: specifies whether the pin is logically inverted.
+       - 0 = active high
+       - 1 = active low
 - st,bank-name	  : Should be a name string for this bank as specified in
   datasheet.
 
@@ -76,23 +79,23 @@ include/dt-bindings/interrupt-controller/irq.h
 
 Example:
 	pin-controller-sbc {
-		#address-cells	= <1>;
-		#size-cells	= <1>;
-		compatible	= "st,stih415-sbc-pinctrl";
-		st,syscfg	= <&syscfg_sbc>;
-		reg 		= <0xfe61f080 0x4>;
-		reg-names	= "irqmux";
-		interrupts 	= <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names	= "irqmux";
-		ranges 		= <0 0xfe610000 0x5000>;
-
-		PIO0: gpio@fe610000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,stih407-sbc-pinctrl";
+		st,syscfg = <&syscfg_sbc>;
+		reg = <0x0961f080 0x4>;
+		reg-names = "irqmux";
+		interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>;
+		interrupt-names = "irqmux";
+		ranges = <0 0x09610000 0x6000>;
+
+		pio0: gpio@09610000 {
 			gpio-controller;
-			#gpio-cells	= <1>;
+			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
-			reg		= <0 0x100>;
-			st,bank-name	= "PIO0";
+			reg = <0x0 0x100>;
+			st,bank-name = "PIO0";
 		};
 		...
 		pin-functions nodes follow...
@@ -162,7 +165,7 @@ pin-controller {
 
 sdhci0:sdhci@fe810000{
 	...
-	interrupt-parent = <&PIO3>;
+	interrupt-parent = <&pio3>;
 	#interrupt-cells = <2>;
 	interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; /* Interrupt line via PIO3-3 */
 	interrupt-names = "card-detect";
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
index a54c39ebbf8b..8d893a874634 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
@@ -17,6 +17,9 @@ PMIC's from Qualcomm.
 		    "qcom,pm8994-gpio"
 		    "qcom,pma8084-gpio"
 
+		    And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio"
+		    if the device is on an spmi bus or an ssbi bus respectively
+
 - reg:
 	Usage: required
 	Value type: <prop-encoded-array>
@@ -183,7 +186,7 @@ to specify in a pin configuration subnode:
 Example:
 
 	pm8921_gpio: gpio@150 {
-		compatible = "qcom,pm8921-gpio";
+		compatible = "qcom,pm8921-gpio", "qcom,ssbi-gpio";
 		reg = <0x150 0x160>;
 		interrupts = <192 1>, <193 1>, <194 1>,
 			     <195 1>, <196 1>, <197 1>,
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
index b484ba1af78c..2ab95bc26066 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
@@ -19,6 +19,9 @@ of PMIC's from Qualcomm.
 		    "qcom,pm8994-mpp",
 		    "qcom,pma8084-mpp",
 
+		    And must contain either "qcom,spmi-mpp" or "qcom,ssbi-mpp"
+		    if the device is on an spmi bus or an ssbi bus respectively.
+
 - reg:
 	Usage: required
 	Value type: <prop-encoded-array>
@@ -158,7 +161,7 @@ to specify in a pin configuration subnode:
 Example:
 
 	mpps@a000 {
-		compatible = "qcom,pm8841-mpp";
+		compatible = "qcom,pm8841-mpp", "qcom,spmi-mpp";
 		reg = <0xa000>;
 		gpio-controller;
 		#gpio-cells = <2>;
diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
index e4cf022c992e..13df9498311a 100644
--- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
@@ -17,9 +17,11 @@ Required Properties:
     - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller.
     - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller.
     - "renesas,pfc-r8a7791": for R8A7791 (R-Car M2-W) compatible pin-controller.
+    - "renesas,pfc-r8a7792": for R8A7792 (R-Car V2H) compatible pin-controller.
     - "renesas,pfc-r8a7793": for R8A7793 (R-Car M2-N) compatible pin-controller.
     - "renesas,pfc-r8a7794": for R8A7794 (R-Car E2) compatible pin-controller.
     - "renesas,pfc-r8a7795": for R8A7795 (R-Car H3) compatible pin-controller.
+    - "renesas,pfc-r8a7796": for R8A7796 (R-Car M3-W) compatible pin-controller.
     - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller.
 
   - reg: Base address and length of each memory resource used by the pin
diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
index 587bffb9cbc6..f9753c416974 100644
--- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
@@ -14,6 +14,11 @@ Required properies:
  - #size-cells	: The value of this property must be 1
  - ranges	: defines mapping between pin controller node (parent) to
    gpio-bank node (children).
+ - interrupt-parent: phandle of the interrupt parent to which the external
+   GPIO interrupts are forwarded to.
+ - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node
+   which includes IRQ mux selection register, and the offset of the IRQ mux
+   selection register.
  - pins-are-numbered: Specify the subnodes are using numbered pinmux to
    specify pins.