tty: move drivers/serial/ to drivers/tty/serial/

The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.

This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 0 insertions, 1600 deletions

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
deleted file mode 100644
index e381b895b04d..000000000000
--- a/drivers/serial/bfin_5xx.c
+++ /dev/null
@@ -1,1600 +0,0 @@
-/*
- * Blackfin On-Chip Serial Driver
- *
- * Copyright 2006-2010 Analog Devices Inc.
- *
- * Enter bugs at http://blackfin.uclinux.org/
- *
- * Licensed under the GPL-2 or later.
- */
-
-#if defined(CONFIG_SERIAL_BFIN_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
-#define SUPPORT_SYSRQ
-#endif
-
-#define DRIVER_NAME "bfin-uart"
-#define pr_fmt(fmt) DRIVER_NAME ": " fmt
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/gfp.h>
-#include <linux/io.h>
-#include <linux/init.h>
-#include <linux/console.h>
-#include <linux/sysrq.h>
-#include <linux/platform_device.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/serial_core.h>
-#include <linux/gpio.h>
-#include <linux/irq.h>
-#include <linux/kgdb.h>
-#include <linux/slab.h>
-#include <linux/dma-mapping.h>
-
-#include <asm/portmux.h>
-#include <asm/cacheflush.h>
-#include <asm/dma.h>
-
-#define port_membase(uart)     (((struct bfin_serial_port *)(uart))->port.membase)
-#define get_lsr_cache(uart)    (((struct bfin_serial_port *)(uart))->lsr)
-#define put_lsr_cache(uart, v) (((struct bfin_serial_port *)(uart))->lsr = (v))
-#include <asm/bfin_serial.h>
-
-#ifdef CONFIG_SERIAL_BFIN_MODULE
-# undef CONFIG_EARLY_PRINTK
-#endif
-
-#ifdef CONFIG_SERIAL_BFIN_MODULE
-# undef CONFIG_EARLY_PRINTK
-#endif
-
-/* UART name and device definitions */
-#define BFIN_SERIAL_DEV_NAME	"ttyBF"
-#define BFIN_SERIAL_MAJOR	204
-#define BFIN_SERIAL_MINOR	64
-
-static struct bfin_serial_port *bfin_serial_ports[BFIN_UART_NR_PORTS];
-
-#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
-	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
-
-# ifndef CONFIG_SERIAL_BFIN_PIO
-#  error KGDB only support UART in PIO mode.
-# endif
-
-static int kgdboc_port_line;
-static int kgdboc_break_enabled;
-#endif
-/*
- * Setup for console. Argument comes from the menuconfig
- */
-#define DMA_RX_XCOUNT		512
-#define DMA_RX_YCOUNT		(PAGE_SIZE / DMA_RX_XCOUNT)
-
-#define DMA_RX_FLUSH_JIFFIES	(HZ / 50)
-
-#ifdef CONFIG_SERIAL_BFIN_DMA
-static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
-#else
-static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
-#endif
-
-static void bfin_serial_reset_irda(struct uart_port *port);
-
-#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
-	defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
-static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-	if (uart->cts_pin < 0)
-		return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-
-	/* CTS PIN is negative assertive. */
-	if (UART_GET_CTS(uart))
-		return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-	else
-		return TIOCM_DSR | TIOCM_CAR;
-}
-
-static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-	if (uart->rts_pin < 0)
-		return;
-
-	/* RTS PIN is negative assertive. */
-	if (mctrl & TIOCM_RTS)
-		UART_ENABLE_RTS(uart);
-	else
-		UART_DISABLE_RTS(uart);
-}
-
-/*
- * Handle any change of modem status signal.
- */
-static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id)
-{
-	struct bfin_serial_port *uart = dev_id;
-	unsigned int status;
-
-	status = bfin_serial_get_mctrl(&uart->port);
-	uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
-#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
-	uart->scts = 1;
-	UART_CLEAR_SCTS(uart);
-	UART_CLEAR_IER(uart, EDSSI);
-#endif
-
-	return IRQ_HANDLED;
-}
-#else
-static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
-{
-	return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-}
-
-static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
-}
-#endif
-
-/*
- * interrupts are disabled on entry
- */
-static void bfin_serial_stop_tx(struct uart_port *port)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-#ifdef CONFIG_SERIAL_BFIN_DMA
-	struct circ_buf *xmit = &uart->port.state->xmit;
-#endif
-
-	while (!(UART_GET_LSR(uart) & TEMT))
-		cpu_relax();
-
-#ifdef CONFIG_SERIAL_BFIN_DMA
-	disable_dma(uart->tx_dma_channel);
-	xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
-	uart->port.icount.tx += uart->tx_count;
-	uart->tx_count = 0;
-	uart->tx_done = 1;
-#else
-#ifdef CONFIG_BF54x
-	/* Clear TFI bit */
-	UART_PUT_LSR(uart, TFI);
-#endif
-	UART_CLEAR_IER(uart, ETBEI);
-#endif
-}
-
-/*
- * port is locked and interrupts are disabled
- */
-static void bfin_serial_start_tx(struct uart_port *port)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-	struct tty_struct *tty = uart->port.state->port.tty;
-
-#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
-	if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) {
-		uart->scts = 0;
-		uart_handle_cts_change(&uart->port, uart->scts);
-	}
-#endif
-
-	/*
-	 * To avoid losting RX interrupt, we reset IR function
-	 * before sending data.
-	 */
-	if (tty->termios->c_line == N_IRDA)
-		bfin_serial_reset_irda(port);
-
-#ifdef CONFIG_SERIAL_BFIN_DMA
-	if (uart->tx_done)
-		bfin_serial_dma_tx_chars(uart);
-#else
-	UART_SET_IER(uart, ETBEI);
-	bfin_serial_tx_chars(uart);
-#endif
-}
-
-/*
- * Interrupts are enabled
- */
-static void bfin_serial_stop_rx(struct uart_port *port)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-
-	UART_CLEAR_IER(uart, ERBFI);
-}
-
-/*
- * Set the modem control timer to fire immediately.
- */
-static void bfin_serial_enable_ms(struct uart_port *port)
-{
-}
-
-
-#if ANOMALY_05000363 && defined(CONFIG_SERIAL_BFIN_PIO)
-# define UART_GET_ANOMALY_THRESHOLD(uart)    ((uart)->anomaly_threshold)
-# define UART_SET_ANOMALY_THRESHOLD(uart, v) ((uart)->anomaly_threshold = (v))
-#else
-# define UART_GET_ANOMALY_THRESHOLD(uart)    0
-# define UART_SET_ANOMALY_THRESHOLD(uart, v)
-#endif
-
-#ifdef CONFIG_SERIAL_BFIN_PIO
-static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
-{
-	struct tty_struct *tty = NULL;
-	unsigned int status, ch, flg;
-	static struct timeval anomaly_start = { .tv_sec = 0 };
-
-	status = UART_GET_LSR(uart);
-	UART_CLEAR_LSR(uart);
-
- 	ch = UART_GET_CHAR(uart);
- 	uart->port.icount.rx++;
-
-#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
-	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
-	if (kgdb_connected && kgdboc_port_line == uart->port.line
-		&& kgdboc_break_enabled)
-		if (ch == 0x3) {/* Ctrl + C */
-			kgdb_breakpoint();
-			return;
-		}
-
-	if (!uart->port.state || !uart->port.state->port.tty)
-		return;
-#endif
-	tty = uart->port.state->port.tty;
-
-	if (ANOMALY_05000363) {
-		/* The BF533 (and BF561) family of processors have a nice anomaly
-		 * where they continuously generate characters for a "single" break.
-		 * We have to basically ignore this flood until the "next" valid
-		 * character comes across.  Due to the nature of the flood, it is
-		 * not possible to reliably catch bytes that are sent too quickly
-		 * after this break.  So application code talking to the Blackfin
-		 * which sends a break signal must allow at least 1.5 character
-		 * times after the end of the break for things to stabilize.  This
-		 * timeout was picked as it must absolutely be larger than 1
-		 * character time +/- some percent.  So 1.5 sounds good.  All other
-		 * Blackfin families operate properly.  Woo.
-		 */
-		if (anomaly_start.tv_sec) {
-			struct timeval curr;
-			suseconds_t usecs;
-
-			if ((~ch & (~ch + 1)) & 0xff)
-				goto known_good_char;
-
-			do_gettimeofday(&curr);
-			if (curr.tv_sec - anomaly_start.tv_sec > 1)
-				goto known_good_char;
-
-			usecs = 0;
-			if (curr.tv_sec != anomaly_start.tv_sec)
-				usecs += USEC_PER_SEC;
-			usecs += curr.tv_usec - anomaly_start.tv_usec;
-
-			if (usecs > UART_GET_ANOMALY_THRESHOLD(uart))
-				goto known_good_char;
-
-			if (ch)
-				anomaly_start.tv_sec = 0;
-			else
-				anomaly_start = curr;
-
-			return;
-
- known_good_char:
-			status &= ~BI;
-			anomaly_start.tv_sec = 0;
-		}
-	}
-
-	if (status & BI) {
-		if (ANOMALY_05000363)
-			if (bfin_revid() < 5)
-				do_gettimeofday(&anomaly_start);
-		uart->port.icount.brk++;
-		if (uart_handle_break(&uart->port))
-			goto ignore_char;
-		status &= ~(PE | FE);
-	}
-	if (status & PE)
-		uart->port.icount.parity++;
-	if (status & OE)
-		uart->port.icount.overrun++;
-	if (status & FE)
-		uart->port.icount.frame++;
-
-	status &= uart->port.read_status_mask;
-
-	if (status & BI)
-		flg = TTY_BREAK;
-	else if (status & PE)
-		flg = TTY_PARITY;
-	else if (status & FE)
-		flg = TTY_FRAME;
-	else
-		flg = TTY_NORMAL;
-
-	if (uart_handle_sysrq_char(&uart->port, ch))
-		goto ignore_char;
-
-	uart_insert_char(&uart->port, status, OE, ch, flg);
-
- ignore_char:
-	tty_flip_buffer_push(tty);
-}
-
-static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
-{
-	struct circ_buf *xmit = &uart->port.state->xmit;
-
-	if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
-#ifdef CONFIG_BF54x
-		/* Clear TFI bit */
-		UART_PUT_LSR(uart, TFI);
-#endif
-		/* Anomaly notes:
-		 *  05000215 -	we always clear ETBEI within last UART TX
-		 *		interrupt to end a string. It is always set
-		 *		when start a new tx.
-		 */
-		UART_CLEAR_IER(uart, ETBEI);
-		return;
-	}
-
-	if (uart->port.x_char) {
-		UART_PUT_CHAR(uart, uart->port.x_char);
-		uart->port.icount.tx++;
-		uart->port.x_char = 0;
-	}
-
-	while ((UART_GET_LSR(uart) & THRE) && xmit->tail != xmit->head) {
-		UART_PUT_CHAR(uart, xmit->buf[xmit->tail]);
-		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
-		uart->port.icount.tx++;
-	}
-
-	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
-		uart_write_wakeup(&uart->port);
-}
-
-static irqreturn_t bfin_serial_rx_int(int irq, void *dev_id)
-{
-	struct bfin_serial_port *uart = dev_id;
-
-	spin_lock(&uart->port.lock);
-	while (UART_GET_LSR(uart) & DR)
-		bfin_serial_rx_chars(uart);
-	spin_unlock(&uart->port.lock);
-
-	return IRQ_HANDLED;
-}
-
-static irqreturn_t bfin_serial_tx_int(int irq, void *dev_id)
-{
-	struct bfin_serial_port *uart = dev_id;
-
-#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
-	if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) {
-		uart->scts = 0;
-		uart_handle_cts_change(&uart->port, uart->scts);
-	}
-#endif
-	spin_lock(&uart->port.lock);
-	if (UART_GET_LSR(uart) & THRE)
-		bfin_serial_tx_chars(uart);
-	spin_unlock(&uart->port.lock);
-
-	return IRQ_HANDLED;
-}
-#endif
-
-#ifdef CONFIG_SERIAL_BFIN_DMA
-static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart)
-{
-	struct circ_buf *xmit = &uart->port.state->xmit;
-
-	uart->tx_done = 0;
-
-	if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
-		uart->tx_count = 0;
-		uart->tx_done = 1;
-		return;
-	}
-
-	if (uart->port.x_char) {
-		UART_PUT_CHAR(uart, uart->port.x_char);
-		uart->port.icount.tx++;
-		uart->port.x_char = 0;
-	}
-
-	uart->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE);
-	if (uart->tx_count > (UART_XMIT_SIZE - xmit->tail))
-		uart->tx_count = UART_XMIT_SIZE - xmit->tail;
-	blackfin_dcache_flush_range((unsigned long)(xmit->buf+xmit->tail),
-					(unsigned long)(xmit->buf+xmit->tail+uart->tx_count));
-	set_dma_config(uart->tx_dma_channel,
-		set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP,
-			INTR_ON_BUF,
-			DIMENSION_LINEAR,
-			DATA_SIZE_8,
-			DMA_SYNC_RESTART));
-	set_dma_start_addr(uart->tx_dma_channel, (unsigned long)(xmit->buf+xmit->tail));
-	set_dma_x_count(uart->tx_dma_channel, uart->tx_count);
-	set_dma_x_modify(uart->tx_dma_channel, 1);
-	SSYNC();
-	enable_dma(uart->tx_dma_channel);
-
-	UART_SET_IER(uart, ETBEI);
-}
-
-static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart)
-{
-	struct tty_struct *tty = uart->port.state->port.tty;
-	int i, flg, status;
-
-	status = UART_GET_LSR(uart);
-	UART_CLEAR_LSR(uart);
-
-	uart->port.icount.rx +=
-		CIRC_CNT(uart->rx_dma_buf.head, uart->rx_dma_buf.tail,
-		UART_XMIT_SIZE);
-
-	if (status & BI) {
-		uart->port.icount.brk++;
-		if (uart_handle_break(&uart->port))
-			goto dma_ignore_char;
-		status &= ~(PE | FE);
-	}
-	if (status & PE)
-		uart->port.icount.parity++;
-	if (status & OE)
-		uart->port.icount.overrun++;
-	if (status & FE)
-		uart->port.icount.frame++;
-
-	status &= uart->port.read_status_mask;
-
-	if (status & BI)
-		flg = TTY_BREAK;
-	else if (status & PE)
-		flg = TTY_PARITY;
-	else if (status & FE)
-		flg = TTY_FRAME;
-	else
-		flg = TTY_NORMAL;
-
-	for (i = uart->rx_dma_buf.tail; ; i++) {
-		if (i >= UART_XMIT_SIZE)
-			i = 0;
-		if (i == uart->rx_dma_buf.head)
-			break;
-		if (!uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
-			uart_insert_char(&uart->port, status, OE,
-				uart->rx_dma_buf.buf[i], flg);
-	}
-
- dma_ignore_char:
-	tty_flip_buffer_push(tty);
-}
-
-void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
-{
-	int x_pos, pos;
-
-	dma_disable_irq(uart->tx_dma_channel);
-	dma_disable_irq(uart->rx_dma_channel);
-	spin_lock_bh(&uart->port.lock);
-
-	/* 2D DMA RX buffer ring is used. Because curr_y_count and
-	 * curr_x_count can't be read as an atomic operation,
-	 * curr_y_count should be read before curr_x_count. When
-	 * curr_x_count is read, curr_y_count may already indicate
-	 * next buffer line. But, the position calculated here is
-	 * still indicate the old line. The wrong position data may
-	 * be smaller than current buffer tail, which cause garbages
-	 * are received if it is not prohibit.
-	 */
-	uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
-	x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
-	uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
-	if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0)
-		uart->rx_dma_nrows = 0;
-	x_pos = DMA_RX_XCOUNT - x_pos;
-	if (x_pos == DMA_RX_XCOUNT)
-		x_pos = 0;
-
-	pos = uart->rx_dma_nrows * DMA_RX_XCOUNT + x_pos;
-	/* Ignore receiving data if new position is in the same line of
-	 * current buffer tail and small.
-	 */
-	if (pos > uart->rx_dma_buf.tail ||
-		uart->rx_dma_nrows < (uart->rx_dma_buf.tail/DMA_RX_XCOUNT)) {
-		uart->rx_dma_buf.head = pos;
-		bfin_serial_dma_rx_chars(uart);
-		uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
-	}
-
-	spin_unlock_bh(&uart->port.lock);
-	dma_enable_irq(uart->tx_dma_channel);
-	dma_enable_irq(uart->rx_dma_channel);
-
-	mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES);
-}
-
-static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
-{
-	struct bfin_serial_port *uart = dev_id;
-	struct circ_buf *xmit = &uart->port.state->xmit;
-
-#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
-	if (uart->scts && !(bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
-		uart->scts = 0;
-		uart_handle_cts_change(&uart->port, uart->scts);
-	}
-#endif
-
-	spin_lock(&uart->port.lock);
-	if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
-		disable_dma(uart->tx_dma_channel);
-		clear_dma_irqstat(uart->tx_dma_channel);
-		/* Anomaly notes:
-		 *  05000215 -	we always clear ETBEI within last UART TX
-		 *		interrupt to end a string. It is always set
-		 *		when start a new tx.
-		 */
-		UART_CLEAR_IER(uart, ETBEI);
-		xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
-		uart->port.icount.tx += uart->tx_count;
-
-		if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
-			uart_write_wakeup(&uart->port);
-
-		bfin_serial_dma_tx_chars(uart);
-	}
-
-	spin_unlock(&uart->port.lock);
-	return IRQ_HANDLED;
-}
-
-static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id)
-{
-	struct bfin_serial_port *uart = dev_id;
-	unsigned short irqstat;
-	int x_pos, pos;
-
-	spin_lock(&uart->port.lock);
-	irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
-	clear_dma_irqstat(uart->rx_dma_channel);
-
-	uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
-	x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
-	uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
-	if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0)
-		uart->rx_dma_nrows = 0;
-
-	pos = uart->rx_dma_nrows * DMA_RX_XCOUNT;
-	if (pos > uart->rx_dma_buf.tail ||
-		uart->rx_dma_nrows < (uart->rx_dma_buf.tail/DMA_RX_XCOUNT)) {
-		uart->rx_dma_buf.head = pos;
-		bfin_serial_dma_rx_chars(uart);
-		uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
-	}
-
-	spin_unlock(&uart->port.lock);
-
-	return IRQ_HANDLED;
-}
-#endif
-
-/*
- * Return TIOCSER_TEMT when transmitter is not busy.
- */
-static unsigned int bfin_serial_tx_empty(struct uart_port *port)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-	unsigned short lsr;
-
-	lsr = UART_GET_LSR(uart);
-	if (lsr & TEMT)
-		return TIOCSER_TEMT;
-	else
-		return 0;
-}
-
-static void bfin_serial_break_ctl(struct uart_port *port, int break_state)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-	u16 lcr = UART_GET_LCR(uart);
-	if (break_state)
-		lcr |= SB;
-	else
-		lcr &= ~SB;
-	UART_PUT_LCR(uart, lcr);
-	SSYNC();
-}
-
-static int bfin_serial_startup(struct uart_port *port)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-
-#ifdef CONFIG_SERIAL_BFIN_DMA
-	dma_addr_t dma_handle;
-
-	if (request_dma(uart->rx_dma_channel, "BFIN_UART_RX") < 0) {
-		printk(KERN_NOTICE "Unable to attach Blackfin UART RX DMA channel\n");
-		return -EBUSY;
-	}
-
-	if (request_dma(uart->tx_dma_channel, "BFIN_UART_TX") < 0) {
-		printk(KERN_NOTICE "Unable to attach Blackfin UART TX DMA channel\n");
-		free_dma(uart->rx_dma_channel);
-		return -EBUSY;
-	}
-
-	set_dma_callback(uart->rx_dma_channel, bfin_serial_dma_rx_int, uart);
-	set_dma_callback(uart->tx_dma_channel, bfin_serial_dma_tx_int, uart);
-
-	uart->rx_dma_buf.buf = (unsigned char *)dma_alloc_coherent(NULL, PAGE_SIZE, &dma_handle, GFP_DMA);
-	uart->rx_dma_buf.head = 0;
-	uart->rx_dma_buf.tail = 0;
-	uart->rx_dma_nrows = 0;
-
-	set_dma_config(uart->rx_dma_channel,
-		set_bfin_dma_config(DIR_WRITE, DMA_FLOW_AUTO,
-				INTR_ON_ROW, DIMENSION_2D,
-				DATA_SIZE_8,
-				DMA_SYNC_RESTART));
-	set_dma_x_count(uart->rx_dma_channel, DMA_RX_XCOUNT);
-	set_dma_x_modify(uart->rx_dma_channel, 1);
-	set_dma_y_count(uart->rx_dma_channel, DMA_RX_YCOUNT);
-	set_dma_y_modify(uart->rx_dma_channel, 1);
-	set_dma_start_addr(uart->rx_dma_channel, (unsigned long)uart->rx_dma_buf.buf);
-	enable_dma(uart->rx_dma_channel);
-
-	uart->rx_dma_timer.data = (unsigned long)(uart);
-	uart->rx_dma_timer.function = (void *)bfin_serial_rx_dma_timeout;
-	uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
-	add_timer(&(uart->rx_dma_timer));
-#else
-# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
-	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
-	if (kgdboc_port_line == uart->port.line && kgdboc_break_enabled)
-		kgdboc_break_enabled = 0;
-	else {
-# endif
-	if (request_irq(uart->port.irq, bfin_serial_rx_int, IRQF_DISABLED,
-	     "BFIN_UART_RX", uart)) {
-		printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
-		return -EBUSY;
-	}
-
-	if (request_irq
-	    (uart->port.irq+1, bfin_serial_tx_int, IRQF_DISABLED,
-	     "BFIN_UART_TX", uart)) {
-		printk(KERN_NOTICE "Unable to attach BlackFin UART TX interrupt\n");
-		free_irq(uart->port.irq, uart);
-		return -EBUSY;
-	}
-
-# ifdef CONFIG_BF54x
-	{
-		/*
-		 * UART2 and UART3 on BF548 share interrupt PINs and DMA
-		 * controllers with SPORT2 and SPORT3. UART rx and tx
-		 * interrupts are generated in PIO mode only when configure
-		 * their peripheral mapping registers properly, which means
-		 * request corresponding DMA channels in PIO mode as well.
-		 */
-		unsigned uart_dma_ch_rx, uart_dma_ch_tx;
-
-		switch (uart->port.irq) {
-		case IRQ_UART3_RX:
-			uart_dma_ch_rx = CH_UART3_RX;
-			uart_dma_ch_tx = CH_UART3_TX;
-			break;
-		case IRQ_UART2_RX:
-			uart_dma_ch_rx = CH_UART2_RX;
-			uart_dma_ch_tx = CH_UART2_TX;
-			break;
-		default:
-			uart_dma_ch_rx = uart_dma_ch_tx = 0;
-			break;
-		};
-
-		if (uart_dma_ch_rx &&
-			request_dma(uart_dma_ch_rx, "BFIN_UART_RX") < 0) {
-			printk(KERN_NOTICE"Fail to attach UART interrupt\n");
-			free_irq(uart->port.irq, uart);
-			free_irq(uart->port.irq + 1, uart);
-			return -EBUSY;
-		}
-		if (uart_dma_ch_tx &&
-			request_dma(uart_dma_ch_tx, "BFIN_UART_TX") < 0) {
-			printk(KERN_NOTICE "Fail to attach UART interrupt\n");
-			free_dma(uart_dma_ch_rx);
-			free_irq(uart->port.irq, uart);
-			free_irq(uart->port.irq + 1, uart);
-			return -EBUSY;
-		}
-	}
-# endif
-# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
-	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
-	}
-# endif
-#endif
-
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
-	if (uart->cts_pin >= 0) {
-		if (request_irq(gpio_to_irq(uart->cts_pin),
-			bfin_serial_mctrl_cts_int,
-			IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING |
-			IRQF_DISABLED, "BFIN_UART_CTS", uart)) {
-			uart->cts_pin = -1;
-			pr_info("Unable to attach BlackFin UART CTS interrupt. So, disable it.\n");
-		}
-	}
-	if (uart->rts_pin >= 0) {
-		gpio_direction_output(uart->rts_pin, 0);
-	}
-#endif
-#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
-	if (uart->cts_pin >= 0 && request_irq(uart->status_irq,
-		bfin_serial_mctrl_cts_int,
-		IRQF_DISABLED, "BFIN_UART_MODEM_STATUS", uart)) {
-		uart->cts_pin = -1;
-		pr_info("Unable to attach BlackFin UART Modem Status interrupt.\n");
-	}
-
-	/* CTS RTS PINs are negative assertive. */
-	UART_PUT_MCR(uart, ACTS);
-	UART_SET_IER(uart, EDSSI);
-#endif
-
-	UART_SET_IER(uart, ERBFI);
-	return 0;
-}
-
-static void bfin_serial_shutdown(struct uart_port *port)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-
-#ifdef CONFIG_SERIAL_BFIN_DMA
-	disable_dma(uart->tx_dma_channel);
-	free_dma(uart->tx_dma_channel);
-	disable_dma(uart->rx_dma_channel);
-	free_dma(uart->rx_dma_channel);
-	del_timer(&(uart->rx_dma_timer));
-	dma_free_coherent(NULL, PAGE_SIZE, uart->rx_dma_buf.buf, 0);
-#else
-#ifdef CONFIG_BF54x
-	switch (uart->port.irq) {
-	case IRQ_UART3_RX:
-		free_dma(CH_UART3_RX);
-		free_dma(CH_UART3_TX);
-		break;
-	case IRQ_UART2_RX:
-		free_dma(CH_UART2_RX);
-		free_dma(CH_UART2_TX);
-		break;
-	default:
-		break;
-	};
-#endif
-	free_irq(uart->port.irq, uart);
-	free_irq(uart->port.irq+1, uart);
-#endif
-
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
-	if (uart->cts_pin >= 0)
-		free_irq(gpio_to_irq(uart->cts_pin), uart);
-#endif
-#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
-	if (uart->cts_pin >= 0)
-		free_irq(uart->status_irq, uart);
-#endif
-}
-
-static void
-bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
-		   struct ktermios *old)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-	unsigned long flags;
-	unsigned int baud, quot;
-	unsigned short val, ier, lcr = 0;
-
-	switch (termios->c_cflag & CSIZE) {
-	case CS8:
-		lcr = WLS(8);
-		break;
-	case CS7:
-		lcr = WLS(7);
-		break;
-	case CS6:
-		lcr = WLS(6);
-		break;
-	case CS5:
-		lcr = WLS(5);
-		break;
-	default:
-		printk(KERN_ERR "%s: word lengh not supported\n",
-			__func__);
-	}
-
-	/* Anomaly notes:
-	 *  05000231 -  STOP bit is always set to 1 whatever the user is set.
-	 */
-	if (termios->c_cflag & CSTOPB) {
-		if (ANOMALY_05000231)
-			printk(KERN_WARNING "STOP bits other than 1 is not "
-				"supported in case of anomaly 05000231.\n");
-		else
-			lcr |= STB;
-	}
-	if (termios->c_cflag & PARENB)
-		lcr |= PEN;
-	if (!(termios->c_cflag & PARODD))
-		lcr |= EPS;
-	if (termios->c_cflag & CMSPAR)
-		lcr |= STP;
-
-	spin_lock_irqsave(&uart->port.lock, flags);
-
-	port->read_status_mask = OE;
-	if (termios->c_iflag & INPCK)
-		port->read_status_mask |= (FE | PE);
-	if (termios->c_iflag & (BRKINT | PARMRK))
-		port->read_status_mask |= BI;
-
-	/*
-	 * Characters to ignore
-	 */
-	port->ignore_status_mask = 0;
-	if (termios->c_iflag & IGNPAR)
-		port->ignore_status_mask |= FE | PE;
-	if (termios->c_iflag & IGNBRK) {
-		port->ignore_status_mask |= BI;
-		/*
-		 * If we're ignoring parity and break indicators,
-		 * ignore overruns too (for real raw support).
-		 */
-		if (termios->c_iflag & IGNPAR)
-			port->ignore_status_mask |= OE;
-	}
-
-	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
-	quot = uart_get_divisor(port, baud);
-
-	/* If discipline is not IRDA, apply ANOMALY_05000230 */
-	if (termios->c_line != N_IRDA)
-		quot -= ANOMALY_05000230;
-
-	UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15);
-
-	/* Disable UART */
-	ier = UART_GET_IER(uart);
-	UART_DISABLE_INTS(uart);
-
-	/* Set DLAB in LCR to Access DLL and DLH */
-	UART_SET_DLAB(uart);
-
-	UART_PUT_DLL(uart, quot & 0xFF);
-	UART_PUT_DLH(uart, (quot >> 8) & 0xFF);
-	SSYNC();
-
-	/* Clear DLAB in LCR to Access THR RBR IER */
-	UART_CLEAR_DLAB(uart);
-
-	UART_PUT_LCR(uart, lcr);
-
-	/* Enable UART */
-	UART_ENABLE_INTS(uart, ier);
-
-	val = UART_GET_GCTL(uart);
-	val |= UCEN;
-	UART_PUT_GCTL(uart, val);
-
-	/* Port speed changed, update the per-port timeout. */
-	uart_update_timeout(port, termios->c_cflag, baud);
-
-	spin_unlock_irqrestore(&uart->port.lock, flags);
-}
-
-static const char *bfin_serial_type(struct uart_port *port)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-
-	return uart->port.type == PORT_BFIN ? "BFIN-UART" : NULL;
-}
-
-/*
- * Release the memory region(s) being used by 'port'.
- */
-static void bfin_serial_release_port(struct uart_port *port)
-{
-}
-
-/*
- * Request the memory region(s) being used by 'port'.
- */
-static int bfin_serial_request_port(struct uart_port *port)
-{
-	return 0;
-}
-
-/*
- * Configure/autoconfigure the port.
- */
-static void bfin_serial_config_port(struct uart_port *port, int flags)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-
-	if (flags & UART_CONFIG_TYPE &&
-	    bfin_serial_request_port(&uart->port) == 0)
-		uart->port.type = PORT_BFIN;
-}
-
-/*
- * Verify the new serial_struct (for TIOCSSERIAL).
- * The only change we allow are to the flags and type, and
- * even then only between PORT_BFIN and PORT_UNKNOWN
- */
-static int
-bfin_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
-{
-	return 0;
-}
-
-/*
- * Enable the IrDA function if tty->ldisc.num is N_IRDA.
- * In other cases, disable IrDA function.
- */
-static void bfin_serial_set_ldisc(struct uart_port *port, int ld)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-	unsigned short val;
-
-	switch (ld) {
-	case N_IRDA:
-		val = UART_GET_GCTL(uart);
-		val |= (IREN | RPOLC);
-		UART_PUT_GCTL(uart, val);
-		break;
-	default:
-		val = UART_GET_GCTL(uart);
-		val &= ~(IREN | RPOLC);
-		UART_PUT_GCTL(uart, val);
-	}
-}
-
-static void bfin_serial_reset_irda(struct uart_port *port)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-	unsigned short val;
-
-	val = UART_GET_GCTL(uart);
-	val &= ~(IREN | RPOLC);
-	UART_PUT_GCTL(uart, val);
-	SSYNC();
-	val |= (IREN | RPOLC);
-	UART_PUT_GCTL(uart, val);
-	SSYNC();
-}
-
-#ifdef CONFIG_CONSOLE_POLL
-/* Anomaly notes:
- *  05000099 -  Because we only use THRE in poll_put and DR in poll_get,
- *		losing other bits of UART_LSR is not a problem here.
- */
-static void bfin_serial_poll_put_char(struct uart_port *port, unsigned char chr)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-
-	while (!(UART_GET_LSR(uart) & THRE))
-		cpu_relax();
-
-	UART_CLEAR_DLAB(uart);
-	UART_PUT_CHAR(uart, (unsigned char)chr);
-}
-
-static int bfin_serial_poll_get_char(struct uart_port *port)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-	unsigned char chr;
-
-	while (!(UART_GET_LSR(uart) & DR))
-		cpu_relax();
-
-	UART_CLEAR_DLAB(uart);
-	chr = UART_GET_CHAR(uart);
-
-	return chr;
-}
-#endif
-
-#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
-	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
-static void bfin_kgdboc_port_shutdown(struct uart_port *port)
-{
-	if (kgdboc_break_enabled) {
-		kgdboc_break_enabled = 0;
-		bfin_serial_shutdown(port);
-	}
-}
-
-static int bfin_kgdboc_port_startup(struct uart_port *port)
-{
-	kgdboc_port_line = port->line;
-	kgdboc_break_enabled = !bfin_serial_startup(port);
-	return 0;
-}
-#endif
-
-static struct uart_ops bfin_serial_pops = {
-	.tx_empty	= bfin_serial_tx_empty,
-	.set_mctrl	= bfin_serial_set_mctrl,
-	.get_mctrl	= bfin_serial_get_mctrl,
-	.stop_tx	= bfin_serial_stop_tx,
-	.start_tx	= bfin_serial_start_tx,
-	.stop_rx	= bfin_serial_stop_rx,
-	.enable_ms	= bfin_serial_enable_ms,
-	.break_ctl	= bfin_serial_break_ctl,
-	.startup	= bfin_serial_startup,
-	.shutdown	= bfin_serial_shutdown,
-	.set_termios	= bfin_serial_set_termios,
-	.set_ldisc	= bfin_serial_set_ldisc,
-	.type		= bfin_serial_type,
-	.release_port	= bfin_serial_release_port,
-	.request_port	= bfin_serial_request_port,
-	.config_port	= bfin_serial_config_port,
-	.verify_port	= bfin_serial_verify_port,
-#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
-	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
-	.kgdboc_port_startup	= bfin_kgdboc_port_startup,
-	.kgdboc_port_shutdown	= bfin_kgdboc_port_shutdown,
-#endif
-#ifdef CONFIG_CONSOLE_POLL
-	.poll_put_char	= bfin_serial_poll_put_char,
-	.poll_get_char	= bfin_serial_poll_get_char,
-#endif
-};
-
-#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
-/*
- * If the port was already initialised (eg, by a boot loader),
- * try to determine the current setup.
- */
-static void __init
-bfin_serial_console_get_options(struct bfin_serial_port *uart, int *baud,
-			   int *parity, int *bits)
-{
-	unsigned short status;
-
-	status = UART_GET_IER(uart) & (ERBFI | ETBEI);
-	if (status == (ERBFI | ETBEI)) {
-		/* ok, the port was enabled */
-		u16 lcr, dlh, dll;
-
-		lcr = UART_GET_LCR(uart);
-
-		*parity = 'n';
-		if (lcr & PEN) {
-			if (lcr & EPS)
-				*parity = 'e';
-			else
-				*parity = 'o';
-		}
-		switch (lcr & 0x03) {
-			case 0:	*bits = 5; break;
-			case 1:	*bits = 6; break;
-			case 2:	*bits = 7; break;
-			case 3:	*bits = 8; break;
-		}
-		/* Set DLAB in LCR to Access DLL and DLH */
-		UART_SET_DLAB(uart);
-
-		dll = UART_GET_DLL(uart);
-		dlh = UART_GET_DLH(uart);
-
-		/* Clear DLAB in LCR to Access THR RBR IER */
-		UART_CLEAR_DLAB(uart);
-
-		*baud = get_sclk() / (16*(dll | dlh << 8));
-	}
-	pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __func__, *baud, *parity, *bits);
-}
-
-static struct uart_driver bfin_serial_reg;
-
-static void bfin_serial_console_putchar(struct uart_port *port, int ch)
-{
-	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-	while (!(UART_GET_LSR(uart) & THRE))
-		barrier();
-	UART_PUT_CHAR(uart, ch);
-}
-
-#endif /* defined (CONFIG_SERIAL_BFIN_CONSOLE) ||
-		 defined (CONFIG_EARLY_PRINTK) */
-
-#ifdef CONFIG_SERIAL_BFIN_CONSOLE
-#define CLASS_BFIN_CONSOLE	"bfin-console"
-/*
- * Interrupts are disabled on entering
- */
-static void
-bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
-{
-	struct bfin_serial_port *uart = bfin_serial_ports[co->index];
-	unsigned long flags;
-
-	spin_lock_irqsave(&uart->port.lock, flags);
-	uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
-	spin_unlock_irqrestore(&uart->port.lock, flags);
-
-}
-
-static int __init
-bfin_serial_console_setup(struct console *co, char *options)
-{
-	struct bfin_serial_port *uart;
-	int baud = 57600;
-	int bits = 8;
-	int parity = 'n';
-# if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
-	defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
-	int flow = 'r';
-# else
-	int flow = 'n';
-# endif
-
-	/*
-	 * Check whether an invalid uart number has been specified, and
-	 * if so, search for the first available port that does have
-	 * console support.
-	 */
-	if (co->index < 0 || co->index >= BFIN_UART_NR_PORTS)
-		return -ENODEV;
-
-	uart = bfin_serial_ports[co->index];
-	if (!uart)
-		return -ENODEV;
-
-	if (options)
-		uart_parse_options(options, &baud, &parity, &bits, &flow);
-	else
-		bfin_serial_console_get_options(uart, &baud, &parity, &bits);
-
-	return uart_set_options(&uart->port, co, baud, parity, bits, flow);
-}
-
-static struct console bfin_serial_console = {
-	.name		= BFIN_SERIAL_DEV_NAME,
-	.write		= bfin_serial_console_write,
-	.device		= uart_console_device,
-	.setup		= bfin_serial_console_setup,
-	.flags		= CON_PRINTBUFFER,
-	.index		= -1,
-	.data		= &bfin_serial_reg,
-};
-#define BFIN_SERIAL_CONSOLE	&bfin_serial_console
-#else
-#define BFIN_SERIAL_CONSOLE	NULL
-#endif /* CONFIG_SERIAL_BFIN_CONSOLE */
-
-#ifdef	CONFIG_EARLY_PRINTK
-static struct bfin_serial_port bfin_earlyprintk_port;
-#define CLASS_BFIN_EARLYPRINTK	"bfin-earlyprintk"
-
-/*
- * Interrupts are disabled on entering
- */
-static void
-bfin_earlyprintk_console_write(struct console *co, const char *s, unsigned int count)
-{
-	unsigned long flags;
-
-	if (bfin_earlyprintk_port.port.line != co->index)
-		return;
-
-	spin_lock_irqsave(&bfin_earlyprintk_port.port.lock, flags);
-	uart_console_write(&bfin_earlyprintk_port.port, s, count,
-		bfin_serial_console_putchar);
-	spin_unlock_irqrestore(&bfin_earlyprintk_port.port.lock, flags);
-}
-
-/*
- * This should have a .setup or .early_setup in it, but then things get called
- * without the command line options, and the baud rate gets messed up - so
- * don't let the common infrastructure play with things. (see calls to setup
- * & earlysetup in ./kernel/printk.c:register_console()
- */
-static struct __initdata console bfin_early_serial_console = {
-	.name = "early_BFuart",
-	.write = bfin_earlyprintk_console_write,
-	.device = uart_console_device,
-	.flags = CON_PRINTBUFFER,
-	.index = -1,
-	.data  = &bfin_serial_reg,
-};
-#endif
-
-static struct uart_driver bfin_serial_reg = {
-	.owner			= THIS_MODULE,
-	.driver_name		= DRIVER_NAME,
-	.dev_name		= BFIN_SERIAL_DEV_NAME,
-	.major			= BFIN_SERIAL_MAJOR,
-	.minor			= BFIN_SERIAL_MINOR,
-	.nr			= BFIN_UART_NR_PORTS,
-	.cons			= BFIN_SERIAL_CONSOLE,
-};
-
-static int bfin_serial_suspend(struct platform_device *pdev, pm_message_t state)
-{
-	struct bfin_serial_port *uart = platform_get_drvdata(pdev);
-
-	return uart_suspend_port(&bfin_serial_reg, &uart->port);
-}
-
-static int bfin_serial_resume(struct platform_device *pdev)
-{
-	struct bfin_serial_port *uart = platform_get_drvdata(pdev);
-
-	return uart_resume_port(&bfin_serial_reg, &uart->port);
-}
-
-static int bfin_serial_probe(struct platform_device *pdev)
-{
-	struct resource *res;
-	struct bfin_serial_port *uart = NULL;
-	int ret = 0;
-
-	if (pdev->id < 0 || pdev->id >= BFIN_UART_NR_PORTS) {
-		dev_err(&pdev->dev, "Wrong bfin uart platform device id.\n");
-		return -ENOENT;
-	}
-
-	if (bfin_serial_ports[pdev->id] == NULL) {
-
-		uart = kzalloc(sizeof(*uart), GFP_KERNEL);
-		if (!uart) {
-			dev_err(&pdev->dev,
-				"fail to malloc bfin_serial_port\n");
-			return -ENOMEM;
-		}
-		bfin_serial_ports[pdev->id] = uart;
-
-#ifdef CONFIG_EARLY_PRINTK
-		if (!(bfin_earlyprintk_port.port.membase
-			&& bfin_earlyprintk_port.port.line == pdev->id)) {
-			/*
-			 * If the peripheral PINs of current port is allocated
-			 * in earlyprintk probe stage, don't do it again.
-			 */
-#endif
-		ret = peripheral_request_list(
-			(unsigned short *)pdev->dev.platform_data, DRIVER_NAME);
-		if (ret) {
-			dev_err(&pdev->dev,
-				"fail to request bfin serial peripherals\n");
-			goto out_error_free_mem;
-		}
-#ifdef CONFIG_EARLY_PRINTK
-		}
-#endif
-
-		spin_lock_init(&uart->port.lock);
-		uart->port.uartclk   = get_sclk();
-		uart->port.fifosize  = BFIN_UART_TX_FIFO_SIZE;
-		uart->port.ops       = &bfin_serial_pops;
-		uart->port.line      = pdev->id;
-		uart->port.iotype    = UPIO_MEM;
-		uart->port.flags     = UPF_BOOT_AUTOCONF;
-
-		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-		if (res == NULL) {
-			dev_err(&pdev->dev, "Cannot get IORESOURCE_MEM\n");
-			ret = -ENOENT;
-			goto out_error_free_peripherals;
-		}
-
-		uart->port.membase = ioremap(res->start,
-			res->end - res->start);
-		if (!uart->port.membase) {
-			dev_err(&pdev->dev, "Cannot map uart IO\n");
-			ret = -ENXIO;
-			goto out_error_free_peripherals;
-		}
-		uart->port.mapbase = res->start;
-
-		uart->port.irq = platform_get_irq(pdev, 0);
-		if (uart->port.irq < 0) {
-			dev_err(&pdev->dev, "No uart RX/TX IRQ specified\n");
-			ret = -ENOENT;
-			goto out_error_unmap;
-		}
-
-		uart->status_irq = platform_get_irq(pdev, 1);
-		if (uart->status_irq < 0) {
-			dev_err(&pdev->dev, "No uart status IRQ specified\n");
-			ret = -ENOENT;
-			goto out_error_unmap;
-		}
-
-#ifdef CONFIG_SERIAL_BFIN_DMA
-		uart->tx_done	    = 1;
-		uart->tx_count	    = 0;
-
-		res = platform_get_resource(pdev, IORESOURCE_DMA, 0);
-		if (res == NULL) {
-			dev_err(&pdev->dev, "No uart TX DMA channel specified\n");
-			ret = -ENOENT;
-			goto out_error_unmap;
-		}
-		uart->tx_dma_channel = res->start;
-
-		res = platform_get_resource(pdev, IORESOURCE_DMA, 1);
-		if (res == NULL) {
-			dev_err(&pdev->dev, "No uart RX DMA channel specified\n");
-			ret = -ENOENT;
-			goto out_error_unmap;
-		}
-		uart->rx_dma_channel = res->start;
-
-		init_timer(&(uart->rx_dma_timer));
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
-	defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
-		res = platform_get_resource(pdev, IORESOURCE_IO, 0);
-		if (res == NULL)
-			uart->cts_pin = -1;
-		else
-			uart->cts_pin = res->start;
-
-		res = platform_get_resource(pdev, IORESOURCE_IO, 1);
-		if (res == NULL)
-			uart->rts_pin = -1;
-		else
-			uart->rts_pin = res->start;
-# if defined(CONFIG_SERIAL_BFIN_CTSRTS)
-		if (uart->rts_pin >= 0)
-			gpio_request(uart->rts_pin, DRIVER_NAME);
-# endif
-#endif
-	}
-
-#ifdef CONFIG_SERIAL_BFIN_CONSOLE
-	if (!is_early_platform_device(pdev)) {
-#endif
-		uart = bfin_serial_ports[pdev->id];
-		uart->port.dev = &pdev->dev;
-		dev_set_drvdata(&pdev->dev, uart);
-		ret = uart_add_one_port(&bfin_serial_reg, &uart->port);
-#ifdef CONFIG_SERIAL_BFIN_CONSOLE
-	}
-#endif
-
-	if (!ret)
-		return 0;
-
-	if (uart) {
-out_error_unmap:
-		iounmap(uart->port.membase);
-out_error_free_peripherals:
-		peripheral_free_list(
-			(unsigned short *)pdev->dev.platform_data);
-out_error_free_mem:
-		kfree(uart);
-		bfin_serial_ports[pdev->id] = NULL;
-	}
-
-	return ret;
-}
-
-static int __devexit bfin_serial_remove(struct platform_device *pdev)
-{
-	struct bfin_serial_port *uart = platform_get_drvdata(pdev);
-
-	dev_set_drvdata(&pdev->dev, NULL);
-
-	if (uart) {
-		uart_remove_one_port(&bfin_serial_reg, &uart->port);
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
-		if (uart->rts_pin >= 0)
-			gpio_free(uart->rts_pin);
-#endif
-		iounmap(uart->port.membase);
-		peripheral_free_list(
-			(unsigned short *)pdev->dev.platform_data);
-		kfree(uart);
-		bfin_serial_ports[pdev->id] = NULL;
-	}
-
-	return 0;
-}
-
-static struct platform_driver bfin_serial_driver = {
-	.probe		= bfin_serial_probe,
-	.remove		= __devexit_p(bfin_serial_remove),
-	.suspend	= bfin_serial_suspend,
-	.resume		= bfin_serial_resume,
-	.driver		= {
-		.name	= DRIVER_NAME,
-		.owner	= THIS_MODULE,
-	},
-};
-
-#if defined(CONFIG_SERIAL_BFIN_CONSOLE)
-static __initdata struct early_platform_driver early_bfin_serial_driver = {
-	.class_str = CLASS_BFIN_CONSOLE,
-	.pdrv = &bfin_serial_driver,
-	.requested_id = EARLY_PLATFORM_ID_UNSET,
-};
-
-static int __init bfin_serial_rs_console_init(void)
-{
-	early_platform_driver_register(&early_bfin_serial_driver, DRIVER_NAME);
-
-	early_platform_driver_probe(CLASS_BFIN_CONSOLE, BFIN_UART_NR_PORTS, 0);
-
-	register_console(&bfin_serial_console);
-
-	return 0;
-}
-console_initcall(bfin_serial_rs_console_init);
-#endif
-
-#ifdef CONFIG_EARLY_PRINTK
-/*
- * Memory can't be allocated dynamically during earlyprink init stage.
- * So, do individual probe for earlyprink with a static uart port variable.
- */
-static int bfin_earlyprintk_probe(struct platform_device *pdev)
-{
-	struct resource *res;
-	int ret;
-
-	if (pdev->id < 0 || pdev->id >= BFIN_UART_NR_PORTS) {
-		dev_err(&pdev->dev, "Wrong earlyprintk platform device id.\n");
-		return -ENOENT;
-	}
-
-	ret = peripheral_request_list(
-		(unsigned short *)pdev->dev.platform_data, DRIVER_NAME);
-	if (ret) {
-		dev_err(&pdev->dev,
-				"fail to request bfin serial peripherals\n");
-			return ret;
-	}
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (res == NULL) {
-		dev_err(&pdev->dev, "Cannot get IORESOURCE_MEM\n");
-		ret = -ENOENT;
-		goto out_error_free_peripherals;
-	}
-
-	bfin_earlyprintk_port.port.membase = ioremap(res->start,
-			res->end - res->start);
-	if (!bfin_earlyprintk_port.port.membase) {
-		dev_err(&pdev->dev, "Cannot map uart IO\n");
-		ret = -ENXIO;
-		goto out_error_free_peripherals;
-	}
-	bfin_earlyprintk_port.port.mapbase = res->start;
-	bfin_earlyprintk_port.port.line = pdev->id;
-	bfin_earlyprintk_port.port.uartclk = get_sclk();
-	bfin_earlyprintk_port.port.fifosize  = BFIN_UART_TX_FIFO_SIZE;
-	spin_lock_init(&bfin_earlyprintk_port.port.lock);
-
-	return 0;
-
-out_error_free_peripherals:
-	peripheral_free_list(
-		(unsigned short *)pdev->dev.platform_data);
-
-	return ret;
-}
-
-static struct platform_driver bfin_earlyprintk_driver = {
-	.probe		= bfin_earlyprintk_probe,
-	.driver		= {
-		.name	= DRIVER_NAME,
-		.owner	= THIS_MODULE,
-	},
-};
-
-static __initdata struct early_platform_driver early_bfin_earlyprintk_driver = {
-	.class_str = CLASS_BFIN_EARLYPRINTK,
-	.pdrv = &bfin_earlyprintk_driver,
-	.requested_id = EARLY_PLATFORM_ID_UNSET,
-};
-
-struct console __init *bfin_earlyserial_init(unsigned int port,
-						unsigned int cflag)
-{
-	struct ktermios t;
-	char port_name[20];
-
-	if (port < 0 || port >= BFIN_UART_NR_PORTS)
-		return NULL;
-
-	/*
-	 * Only probe resource of the given port in earlyprintk boot arg.
-	 * The expected port id should be indicated in port name string.
-	 */
-	snprintf(port_name, 20, DRIVER_NAME ".%d", port);
-	early_platform_driver_register(&early_bfin_earlyprintk_driver,
-		port_name);
-	early_platform_driver_probe(CLASS_BFIN_EARLYPRINTK, 1, 0);
-
-	if (!bfin_earlyprintk_port.port.membase)
-		return NULL;
-
-#ifdef CONFIG_SERIAL_BFIN_CONSOLE
-	/*
-	 * If we are using early serial, don't let the normal console rewind
-	 * log buffer, since that causes things to be printed multiple times
-	 */
-	bfin_serial_console.flags &= ~CON_PRINTBUFFER;
-#endif
-
-	bfin_early_serial_console.index = port;
-	t.c_cflag = cflag;
-	t.c_iflag = 0;
-	t.c_oflag = 0;
-	t.c_lflag = ICANON;
-	t.c_line = port;
-	bfin_serial_set_termios(&bfin_earlyprintk_port.port, &t, &t);
-
-	return &bfin_early_serial_console;
-}
-#endif /* CONFIG_EARLY_PRINTK */
-
-static int __init bfin_serial_init(void)
-{
-	int ret;
-
-	pr_info("Blackfin serial driver\n");
-
-	ret = uart_register_driver(&bfin_serial_reg);
-	if (ret) {
-		pr_err("failed to register %s:%d\n",
-			bfin_serial_reg.driver_name, ret);
-	}
-
-	ret = platform_driver_register(&bfin_serial_driver);
-	if (ret) {
-		pr_err("fail to register bfin uart\n");
-		uart_unregister_driver(&bfin_serial_reg);
-	}
-
-	return ret;
-}
-
-static void __exit bfin_serial_exit(void)
-{
-	platform_driver_unregister(&bfin_serial_driver);
-	uart_unregister_driver(&bfin_serial_reg);
-}
-
-
-module_init(bfin_serial_init);
-module_exit(bfin_serial_exit);
-
-MODULE_AUTHOR("Sonic Zhang, Aubrey Li");
-MODULE_DESCRIPTION("Blackfin generic serial port driver");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS_CHARDEV_MAJOR(BFIN_SERIAL_MAJOR);
-MODULE_ALIAS("platform:bfin-uart");