summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--arch/arm/configs/pcl052_defconfig34
-rw-r--r--arch/arm/mach-mvf/board-pcl052.c199
-rw-r--r--arch/arm/mach-mvf/mvf_fec.c3
3 files changed, 57 insertions, 179 deletions
diff --git a/arch/arm/configs/pcl052_defconfig b/arch/arm/configs/pcl052_defconfig
index 1437e1ce0de0..b544cf11d6e6 100644
--- a/arch/arm/configs/pcl052_defconfig
+++ b/arch/arm/configs/pcl052_defconfig
@@ -3,6 +3,7 @@
# Linux/arm 3.0.15 Kernel Configuration
#
CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_HAVE_SCHED_CLOCK=y
CONFIG_GENERIC_GPIO=y
@@ -290,10 +291,12 @@ CONFIG_FORCE_MAX_ZONEORDER=13
CONFIG_ARCH_MVFA5=y
CONFIG_SOC_MVFA5=y
# CONFIG_MACH_MVFA5_TWR_VF700 is not set
-CONFIG_MACH_PCM052=y
+# CONFIG_MACH_PCM052 is not set
+CONFIG_MACH_PCL052=y
CONFIG_ISP1504_MXC=y
# CONFIG_MXC_IRQ_PRIOR is not set
-# CONFIG_MXC_PWM is not set
+CONFIG_MXC_PWM=m
+# CONFIG_MXC_PWM_CPWM is not set
# CONFIG_MXC_DEBUG_BOARD is not set
CONFIG_HAVE_PIT=y
CONFIG_MXC_USE_PIT=y
@@ -678,7 +681,7 @@ CONFIG_MISC_DEVICES=y
# CONFIG_DS1682 is not set
# CONFIG_TI_DAC7512 is not set
# CONFIG_BMP085 is not set
-# CONFIG_MVF_ADC is not set
+CONFIG_MVF_ADC=y
# CONFIG_C2PORT is not set
#
@@ -917,6 +920,7 @@ CONFIG_INPUT_MISC=y
# CONFIG_INPUT_CM109 is not set
CONFIG_INPUT_UINPUT=y
# CONFIG_INPUT_PCF8574 is not set
+# CONFIG_INPUT_PWM_BEEPER is not set
# CONFIG_INPUT_GPIO_ROTARY_ENCODER is not set
# CONFIG_INPUT_ADXL34X is not set
# CONFIG_INPUT_CMA3000 is not set
@@ -1023,10 +1027,10 @@ CONFIG_SPI_MASTER=y
#
# CONFIG_SPI_ALTERA is not set
# CONFIG_SPI_BITBANG is not set
-# CONFIG_SPI_MVF_QSPI is not set
+CONFIG_SPI_MVF_QSPI=m
# CONFIG_SPI_GPIO is not set
# CONFIG_SPI_IMX is not set
-CONFIG_SPI_MVF=y
+CONFIG_SPI_MVF=m
# CONFIG_SPI_MVF_DSPI_EDMA is not set
# CONFIG_SPI_OC_TINY is not set
# CONFIG_SPI_PXA2XX_PCI is not set
@@ -1036,7 +1040,7 @@ CONFIG_SPI_MVF=y
#
# SPI Protocol Masters
#
-# CONFIG_SPI_SPIDEV is not set
+CONFIG_SPI_SPIDEV=m
# CONFIG_SPI_TLE62X0 is not set
#
@@ -1098,7 +1102,20 @@ CONFIG_GPIO_SYSFS=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_WATCHDOG is not set
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+# CONFIG_MAX63XX_WATCHDOG is not set
+CONFIG_IMX2_WDT=y
+
+#
+# USB-based Watchdog Cards
+#
+# CONFIG_USBPCWATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
#
@@ -1186,6 +1203,7 @@ CONFIG_FB_SYS_FOPS=y
#
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_MVF_DCU=y
+CONFIG_MVF_TDA_998X=y
# CONFIG_MVF_DCU_BLANKING_TEST is not set
# CONFIG_FB_TMIO is not set
# CONFIG_FB_UDL is not set
@@ -1262,8 +1280,8 @@ CONFIG_SND_SOC=y
# CONFIG_SND_SOC_CACHE_LZO is not set
# CONFIG_SND_IMX_SOC is not set
CONFIG_SND_MVF_SOC=y
-CONFIG_SND_MVF_SOC_TWR=y
# CONFIG_SND_SOC_MVF_SGTL5000 is not set
+# CONFIG_SND_SOC_PCM052_SGTL5000 is not set
CONFIG_SND_SOC_I2C_AND_SPI=y
# CONFIG_SND_SOC_ALL_CODECS is not set
# CONFIG_SOUND_PRIME is not set
diff --git a/arch/arm/mach-mvf/board-pcl052.c b/arch/arm/mach-mvf/board-pcl052.c
index d87cc0e8c977..08a59470d434 100644
--- a/arch/arm/mach-mvf/board-pcl052.c
+++ b/arch/arm/mach-mvf/board-pcl052.c
@@ -47,7 +47,7 @@
#include <linux/pmic_status.h>
#include <linux/ipu.h>
#include <linux/mxcfb.h>
-#include <linux/phy.h> // SP: added for reference to phy_ functions, ex. phy_register_fixup
+#include <linux/phy.h>
#include <linux/pwm_backlight.h>
#include <linux/leds_pwm.h>
#include <linux/fec.h>
@@ -74,7 +74,6 @@
#include <mach/mxc_asrc.h>
#include <mach/mipi_dsi.h>
#include <mach/mipi_csi2.h>
-#include <mach/fsl_l2_switch.h>
#include <asm/irq.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
@@ -89,14 +88,10 @@
#define PCL052_TS_IRQ 32
/* FEC1 definitions */
-#define FEC1_BUS_ID "2:01" // SP: BUS_ID - required to use phy-fixup specifically for the ETH1 PHY
+#define FEC1_BUS_ID "2:01"
-#define KSZ8051_PHY_CTRL2 0x1F // SP: PHY Control 2 register address
-#define KSZ8051_50MHZ_CLK_MODE (1 << 7) // SP: PHY Control 2 register setting for 50 MHz clock mode
-
-#ifdef PCM952_REV0
-#undef PCM952_REV0
-#endif
+#define KSZ8051_PHY_CTRL2 0x1F
+#define KSZ8051_50MHZ_CLK_MODE (1 << 7)
static iomux_v3_cfg_t pcl052_pads[] = {
@@ -108,8 +103,8 @@ static iomux_v3_cfg_t pcl052_pads[] = {
MVF600_PAD18_PTA28__SDHC1_DAT2,
MVF600_PAD19_PTA29__SDHC1_DAT3,
/*set PTB28 as GPIO for sdhc card detecting*/
- // GPIO[98]
MVF600_PAD98_PTB28__SDHC1_SW_CD,
+
/*I2C2*/
MVF600_PAD12_PTA22__I2C2_SCL,
MVF600_PAD13_PTA23__I2C2_SDA,
@@ -129,7 +124,7 @@ static iomux_v3_cfg_t pcl052_pads[] = {
MVF600_PAD44_PTB22__DSPI0_SCK,
/*FEC0 not supported*/
-#if defined(CONFIG_FEC1) || defined(CONFIG_FSL_L2_SWITCH)
+#if defined(CONFIG_FEC1)
/*FEC1*/
MVF600_PAD54_PTC9__RMII1_MDC,
MVF600_PAD55_PTC10__RMII1_MDIO,
@@ -141,8 +136,8 @@ static iomux_v3_cfg_t pcl052_pads[] = {
MVF600_PAD61_PTC16__RMII1_TXD0,
MVF600_PAD62_PTC17__RMII1_TXEN,
#endif
- /*TDA19988x HDMI Encoder*/
- /***Video*/
+ /*TDA19988x HDMI Encoder*/
+ /***Video*/
MVF600_PAD108_PTE3_LCD_ENABLE,
MVF600_PAD105_PTE0_DCU0_HSYNC,
MVF600_PAD106_PTE1_DCU0_VSYNC,
@@ -172,33 +167,29 @@ static iomux_v3_cfg_t pcl052_pads[] = {
MVF600_PAD131_PTE26_DCU0_B5,
MVF600_PAD132_PTE27_DCU0_B6,
MVF600_PAD133_PTE28_DCU0_B7,
- /* MVF600_PAD53_PTC8__GPIO_TDA_INT*/
- IOMUX_PAD(0x00D4, 0x00D4, IOMUX_CONFIG_ALT0, 0x0000, 0,
- PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_SPEED_MED
- | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_25ohm
- | PAD_CTL_ODE | PAD_CTL_IBE_ENABLE),
-
- /***Audio*/
- /* BCLK ACLK*/
+ /* MVF600_PAD53_PTC8__GPIO_TDA_INT*/
+ IOMUX_PAD(0x00D4, 0x00D4, IOMUX_CONFIG_ALT0, 0x0000, 0,
+ PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_SPEED_MED |
+ PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_25ohm |
+ PAD_CTL_ODE | PAD_CTL_IBE_ENABLE),
+
+ /***Audio*/
+ /* BCLK ACLK*/
MVF600_PAD6_PTA16_SAI2_TX_BCLK,
- /* SYNC WS/AP0 */
+ /* SYNC WS/AP0 */
MVF600_PAD9_PTA19_SAI2_TX_SYNC,
- /* DATA AXR0/AP1 */
+ /* DATA AXR0/AP1 */
MVF600_PAD8_PTA18_SAI2_TX_DATA,
- /* PTB10 MCLK OSC_IN/AP3 CKIO1 */
- IOMUX_PAD(0x0080, 0x0080, 6, 0x0000, 0, \
- MVF600_SAI_PAD_CTRL | PAD_CTL_IBE_ENABLE),
+ /* PTB10 MCLK OSC_IN/AP3 CKIO1 */
+ IOMUX_PAD(0x0080, 0x0080, 6, 0x0000, 0, \
+ MVF600_SAI_PAD_CTRL | PAD_CTL_IBE_ENABLE),
/*UART1*/
MVF600_PAD26_PTB4_UART1_TX,
MVF600_PAD27_PTB5_UART1_RX,
/*USB0/1 VBUS_EN*/
-#ifdef PCM952_REV0
- MVF600_PAD6_PTA16__USB0_VBUS_EN,
-#else
MVF600_PAD134_PTA7__USB_VBUS_EN,
-#endif
MVF600_PAD7_PTA17__USB_OC_N,
/* Quad SPI */
@@ -255,26 +246,6 @@ static struct fec_platform_data fec_data __initdata = {
.phy = PHY_INTERFACE_MODE_RMII,
};
-static struct switch_platform_data switch_data __initdata = {
- .phy = PHY_INTERFACE_MODE_RMII,
-};
-
-/* SP: Added function - mvf_fec1_phy_fixup
- * Additional configuration is required to setup ETH1 on the phyCORE-Vybrid
- * (1) Set to 50 MHz (enable bit 7 in the PHY control 2 register)
- - Write: reg - 0x1F; data - (0x1 << 7)
-*/
-
-static int mvf_fec1_phy_fixup(struct phy_device *phydev)
-{
- int regval;
- regval = phy_read(phydev, KSZ8051_PHY_CTRL2); // read current value of PHY Control 2 register
- regval |= KSZ8051_50MHZ_CLK_MODE; // enable 50MHz clock mode
- phy_write(phydev, KSZ8051_PHY_CTRL2, regval); // write to PHY Control 2 register
-
- return 0;
-}
-
static int pcl052_spi_cs[] = {
41,
};
@@ -298,85 +269,10 @@ static const struct spi_mvf_master pcl052_qspi_data __initconst = {
.cs_control = NULL,
};
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
-static struct mtd_partition at26df081a_partitions[] = {
- {
- .name = "at26df081a",
- .size = (1024 * 64 * 16),
- .offset = 0x00000000,
- .mask_flags = 0,
- }
-};
-
-static struct flash_platform_data at26df081a_platform_data = {
- .name = "Atmel at26df081a SPI Flash chip",
- .parts = at26df081a_partitions,
- .nr_parts = ARRAY_SIZE(at26df081a_partitions),
- .type = "at26df081a",
-};
-
-static struct spi_mvf_chip at26df081a_chip_info = {
- .mode = SPI_MODE_3,
- .bits_per_word = 8,
- .void_write_data = 0,
- .dbr = 0,
- .pbr = 0,
- .br = 0,
- .pcssck = 0,
- .pasc = 0,
- .pdt = 0,
- .cssck = 0,
- .asc = 0,
- .dt = 0,
-};
-
-static struct mtd_partition s25fl256s_partitions[] = {
- {
- .name = "s25fl256s",
- .size = (1024 * 64 * 256),
- .offset = 0x00000000,
- .mask_flags = 0,
- }
-};
-
-static struct flash_platform_data s25fl256s_spi_flash_data = {
- .name = "Spansion s25fl128s SPI Flash chip",
- .parts = s25fl256s_partitions,
- .nr_parts = ARRAY_SIZE(s25fl256s_partitions),
- .type = "s25fl128s",
-};
-#endif
-
-static struct spi_board_info mvf_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80)
-#if defined(CONFIG_SPI_MVF_QSPI)
- {
- /* The modalias must be the same as spi device driver name */
- .modalias = "m25p80",
- .max_speed_hz = 20000000,
- .bus_num = 0,
- .chip_select = 0,
- .platform_data = &s25fl256s_spi_flash_data,
- },
-#endif
-#if defined(CONFIG_SPI_MVF)
- {
- /* The modalias must be the same as spi device driver name */
- .modalias = "m25p80",
- .max_speed_hz = 16000000,
- .bus_num = 0,
- .chip_select = 0,
- .platform_data = &at26df081a_platform_data,
- .controller_data = &at26df081a_chip_info
- },
-#endif
-#endif
-};
-
+/* TODO: add SPIDEV support */
static void spi_device_init(void)
{
- spi_register_board_info(mvf_spi_board_info,
- ARRAY_SIZE(mvf_spi_board_info));
+ /* no devices on PCL-052 */
}
#if 1
@@ -397,7 +293,8 @@ static const struct pm_platform_data pcl052_pm_data __initconst = {
#endif
static struct mvf_dcu_platform_data mvf_dcu_pdata = {
- .mode_str = "640x480p_hdmipc", /* works with HDMI PC, not HDMI TV */
+ /* works with HDMI PC, not HDMI TV */
+ .mode_str = "640x480p_hdmipc",
// .mode_str = "720x480p",
.default_bpp = 24,
};
@@ -406,31 +303,12 @@ static void __init fixup_mxc_board(struct machine_desc *desc, struct tag *tags,
char **cmdline, struct meminfo *mi)
{
}
-/*
- * Not defined the cd/wp so far, set it always present for debug*/
+
static const struct esdhc_platform_data pcl052_sd1_data __initconst = {
.cd_gpio = PCL052_SD1_CD,
.wp_gpio = -1,
};
-/* SP: Replicate the AM335x solution for phy_fixup
- * - Call a phy_register_fixup to make the required changes for FEC1/ETH1 - see 'mvf_fec1_phy_fixup'
- * - 'pcl052_setup' will be assigned to .setup in EEPROM platform data (board_eeprom)
- */
-static void pcl052_setup(struct memory_accessor *mem_acc, void *context)
-{
- phy_register_fixup_for_id(FEC1_BUS_ID, mvf_fec1_phy_fixup); // SP: run mvf_fec1_phy_fixup to setup ETH1
- return;
-}
-
-static struct at24_platform_data board_eeprom = {
- .byte_len = 4096,
- .page_size = 32,
- .flags = AT24_FLAG_ADDR16,
- .setup = pcl052_setup, // SP: added to replicate the am335x board file
- .context = (void *)NULL, // SP: added to replicate the am335x board file
-};
-
static struct imxi2c_platform_data pcl052_i2c_data = {
.bitrate = 100000,
};
@@ -448,19 +326,6 @@ static struct mxc_nand_platform_data mvf_data __initdata = {
.width = 2,
};
-static struct led_pwm mvf_led __initdata = {
- .name = "mvf_leds",
- .pwm_id = 1,
- .active_low = 0,
- .max_brightness = 6,
- .pwm_period_ns = 100000000,
-};
-
-static struct led_pwm_platform_data mvf_led_data __initdata = {
- .num_leds = 1,
- .leds = &mvf_led,
-};
-
#define USB_VBUS_ENABLE_PIN 134
static void __init pcl052_init_usb(void)
{
@@ -487,10 +352,6 @@ static void __init pcl052_board_init(void)
mvf_init_fec(fec_data);
#endif
-#ifdef CONFIG_FSL_L2_SWITCH
- mvf_init_switch(switch_data);
-#endif
-
mvf_add_snvs_rtc();
mvf_add_sdhci_esdhc_imx(1, &pcl052_sd1_data);
@@ -509,15 +370,13 @@ static void __init pcl052_board_init(void)
mxc_register_device(&pcl052_audio_device, &pcl052_audio_data);
mvfa5_add_sai(2, &mvf_sai_pdata);
-// mvf_add_wdt(0);
+ mvf_add_wdt(0);
pcl052_init_usb();
mvf_add_nand(&mvf_data);
-// mvf_add_mxc_pwm(0);
-// mvf_add_pwm_leds(&mvf_led_data);
-
+ mvf_add_mxc_pwm(0);
}
static void __init mvf_timer_init(void)
@@ -538,7 +397,7 @@ static struct sys_timer pcl052_timer = {
* initialize __mach_desc_ data structure.
*/
MACHINE_START(PCL052, "PHYTEC Cosmic Board")
- /* Maintainer: Freescale Semiconductor, Inc. */
+ /* Maintainer: PHYTEC America, LLC */
.boot_params = MVF_PHYS_OFFSET + 0x100,
.fixup = fixup_mxc_board,
.map_io = mvf_map_io,
diff --git a/arch/arm/mach-mvf/mvf_fec.c b/arch/arm/mach-mvf/mvf_fec.c
index d51f20519c0b..72c43d6072e3 100644
--- a/arch/arm/mach-mvf/mvf_fec.c
+++ b/arch/arm/mach-mvf/mvf_fec.c
@@ -51,8 +51,9 @@ void __init mvf_init_fec(struct fec_platform_data fec_data)
fec_get_mac_addr(fec_data.mac);
if (!is_valid_ether_addr(fec_data.mac))
memcpy(fec_data.mac, default_mac, ETH_ALEN);
-
+#ifndef CONFIG_MACH_PCL052
mvf_add_fec(0, &fec_data);
+#endif
#ifdef CONFIG_FEC1
mvf_add_fec(1, &fec_data);
#endif