summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt')
-rw-r--r--Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt41
1 files changed, 38 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
index 5187f0dd8b28..2c81e45f1374 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
@@ -14,10 +14,12 @@ Optional properties:
- pinctrl-single,function-off : function off mode for disabled state if
available and same for all registers; if not specified, disabling of
pin functions is ignored
+- pinctrl-single,bit-per-mux : boolean to indicate that one register controls
+ more than one pin
-This driver assumes that there is only one register for each pin,
-and uses the common pinctrl bindings as specified in the pinctrl-bindings.txt
-document in this directory.
+This driver assumes that there is only one register for each pin (unless the
+pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
+specified in the pinctrl-bindings.txt document in this directory.
The pin configuration nodes for pinctrl-single are specified as pinctrl
register offset and value pairs using pinctrl-single,pins. Only the bits
@@ -31,6 +33,15 @@ device pinctrl register, and 0x118 contains the desired value of the
pinctrl register. See the device example and static board pins example
below for more information.
+In case when one register changes more than one pin's mux the
+pinctrl-single,bits need to be used which takes three parameters:
+
+ pinctrl-single,bits = <0xdc 0x18, 0xff>;
+
+Where 0xdc is the offset from the pinctrl register base address for the
+device pinctrl register, 0x18 is the desired value, and 0xff is the sub mask to
+be used when applying this change to the register.
+
Example:
/* SoC common file */
@@ -55,6 +66,15 @@ pmx_wkup: pinmux@4a31e040 {
pinctrl-single,function-mask = <0xffff>;
};
+control_devconf0: pinmux@48002274 {
+ compatible = "pinctrl-single";
+ reg = <0x48002274 4>; /* Single register */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-single,bit-per-mux;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x5F>;
+};
/* board specific .dts file */
@@ -87,6 +107,21 @@ pmx_wkup: pinmux@4a31e040 {
};
};
+&control_devconf0 {
+ mcbsp1_pins: pinmux_mcbsp1_pins {
+ pinctrl-single,bits = <
+ 0x00 0x18 0x18 /* FSR/CLKR signal from FSX/CLKX pin */
+ >;
+ };
+
+ mcbsp2_clks_pins: pinmux_mcbsp2_clks_pins {
+ pinctrl-single,bits = <
+ 0x00 0x40 0x40 /* McBSP2 CLKS from McBSP_CLKS pin */
+ >;
+ };
+
+};
+
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;