diff options
Diffstat (limited to 'Documentation/networking')
21 files changed, 983 insertions, 254 deletions
diff --git a/Documentation/networking/00-INDEX b/Documentation/networking/00-INDEX index fe5c099b8fc8..4edd78dfb362 100644 --- a/Documentation/networking/00-INDEX +++ b/Documentation/networking/00-INDEX @@ -40,8 +40,6 @@ decnet.txt - info on using the DECnet networking layer in Linux. depca.txt - the Digital DEPCA/EtherWORKS DE1?? and DE2?? LANCE Ethernet driver -dgrs.txt - - the Digi International RightSwitch SE-X Ethernet driver dmfe.txt - info on the Davicom DM9102(A)/DM9132/DM9801 fast ethernet driver. e100.txt @@ -50,8 +48,6 @@ e1000.txt - info on Intel's E1000 line of gigabit ethernet boards eql.txt - serial IP load balancing -ethertap.txt - - the Ethertap user space packet reception and transmission driver ewrk3.txt - the Digital EtherWORKS 3 DE203/4/5 Ethernet driver filter.txt @@ -104,8 +100,6 @@ tuntap.txt - TUN/TAP device driver, allowing user space Rx/Tx of packets. vortex.txt - info on using 3Com Vortex (3c590, 3c592, 3c595, 3c597) Ethernet cards. -wavelan.txt - - AT&T GIS (nee NCR) WaveLAN card: An Ethernet-like radio transceiver x25.txt - general info on X.25 development. x25-iface.txt diff --git a/Documentation/networking/LICENSE.qlcnic b/Documentation/networking/LICENSE.qlcnic new file mode 100644 index 000000000000..29ad4b106420 --- /dev/null +++ b/Documentation/networking/LICENSE.qlcnic @@ -0,0 +1,327 @@ +Copyright (c) 2009-2010 QLogic Corporation +QLogic Linux qlcnic NIC Driver + +This program includes a device driver for Linux 2.6 that may be +distributed with QLogic hardware specific firmware binary file. +You may modify and redistribute the device driver code under the +GNU General Public License (a copy of which is attached hereto as +Exhibit A) published by the Free Software Foundation (version 2). + +You may redistribute the hardware specific firmware binary file +under the following terms: + + 1. Redistribution of source code (only if applicable), + must retain the above copyright notice, this list of + conditions and the following disclaimer. + + 2. Redistribution in binary form must reproduce the above + copyright notice, this list of conditions and the + following disclaimer in the documentation and/or other + materials provided with the distribution. + + 3. The name of QLogic Corporation may not be used to + endorse or promote products derived from this software + without specific prior written permission + +REGARDLESS OF WHAT LICENSING MECHANISM IS USED OR APPLICABLE, +THIS PROGRAM IS PROVIDED BY QLOGIC CORPORATION "AS IS'' AND ANY +EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A +PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR +BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, +EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED +TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, +DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON +ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, +OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY +OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +POSSIBILITY OF SUCH DAMAGE. + +USER ACKNOWLEDGES AND AGREES THAT USE OF THIS PROGRAM WILL NOT +CREATE OR GIVE GROUNDS FOR A LICENSE BY IMPLICATION, ESTOPPEL, OR +OTHERWISE IN ANY INTELLECTUAL PROPERTY RIGHTS (PATENT, COPYRIGHT, +TRADE SECRET, MASK WORK, OR OTHER PROPRIETARY RIGHT) EMBODIED IN +ANY OTHER QLOGIC HARDWARE OR SOFTWARE EITHER SOLELY OR IN +COMBINATION WITH THIS PROGRAM. + + +EXHIBIT A + + GNU GENERAL PUBLIC LICENSE + Version 2, June 1991 + + Copyright (C) 1989, 1991 Free Software Foundation, Inc. + 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA + Everyone is permitted to copy and distribute verbatim copies + of this license document, but changing it is not allowed. + + Preamble + + The licenses for most software are designed to take away your +freedom to share and change it. By contrast, the GNU General Public +License is intended to guarantee your freedom to share and change free +software--to make sure the software is free for all its users. This +General Public License applies to most of the Free Software +Foundation's software and to any other program whose authors commit to +using it. (Some other Free Software Foundation software is covered by +the GNU Lesser General Public License instead.) You can apply it to +your programs, too. + + When we speak of free software, we are referring to freedom, not +price. Our General Public Licenses are designed to make sure that you +have the freedom to distribute copies of free software (and charge for +this service if you wish), that you receive source code or can get it +if you want it, that you can change the software or use pieces of it +in new free programs; and that you know you can do these things. + + To protect your rights, we need to make restrictions that forbid +anyone to deny you these rights or to ask you to surrender the rights. +These restrictions translate to certain responsibilities for you if you +distribute copies of the software, or if you modify it. + + For example, if you distribute copies of such a program, whether +gratis or for a fee, you must give the recipients all the rights that +you have. You must make sure that they, too, receive or can get the +source code. And you must show them these terms so they know their +rights. + + We protect your rights with two steps: (1) copyright the software, and +(2) offer you this license which gives you legal permission to copy, +distribute and/or modify the software. + + Also, for each author's protection and ours, we want to make certain +that everyone understands that there is no warranty for this free +software. If the software is modified by someone else and passed on, we +want its recipients to know that what they have is not the original, so +that any problems introduced by others will not reflect on the original +authors' reputations. + + Finally, any free program is threatened constantly by software +patents. We wish to avoid the danger that redistributors of a free +program will individually obtain patent licenses, in effect making the +program proprietary. To prevent this, we have made it clear that any +patent must be licensed for everyone's free use or not licensed at all. + + The precise terms and conditions for copying, distribution and +modification follow. + + GNU GENERAL PUBLIC LICENSE + TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION + + 0. This License applies to any program or other work which contains +a notice placed by the copyright holder saying it may be distributed +under the terms of this General Public License. The "Program", below, +refers to any such program or work, and a "work based on the Program" +means either the Program or any derivative work under copyright law: +that is to say, a work containing the Program or a portion of it, +either verbatim or with modifications and/or translated into another +language. (Hereinafter, translation is included without limitation in +the term "modification".) Each licensee is addressed as "you". + +Activities other than copying, distribution and modification are not +covered by this License; they are outside its scope. The act of +running the Program is not restricted, and the output from the Program +is covered only if its contents constitute a work based on the +Program (independent of having been made by running the Program). +Whether that is true depends on what the Program does. + + 1. You may copy and distribute verbatim copies of the Program's +source code as you receive it, in any medium, provided that you +conspicuously and appropriately publish on each copy an appropriate +copyright notice and disclaimer of warranty; keep intact all the +notices that refer to this License and to the absence of any warranty; +and give any other recipients of the Program a copy of this License +along with the Program. + +You may charge a fee for the physical act of transferring a copy, and +you may at your option offer warranty protection in exchange for a fee. + + 2. You may modify your copy or copies of the Program or any portion +of it, thus forming a work based on the Program, and copy and +distribute such modifications or work under the terms of Section 1 +above, provided that you also meet all of these conditions: + + a) You must cause the modified files to carry prominent notices + stating that you changed the files and the date of any change. + + b) You must cause any work that you distribute or publish, that in + whole or in part contains or is derived from the Program or any + part thereof, to be licensed as a whole at no charge to all third + parties under the terms of this License. + + c) If the modified program normally reads commands interactively + when run, you must cause it, when started running for such + interactive use in the most ordinary way, to print or display an + announcement including an appropriate copyright notice and a + notice that there is no warranty (or else, saying that you provide + a warranty) and that users may redistribute the program under + these conditions, and telling the user how to view a copy of this + License. (Exception: if the Program itself is interactive but + does not normally print such an announcement, your work based on + the Program is not required to print an announcement.) + +These requirements apply to the modified work as a whole. If +identifiable sections of that work are not derived from the Program, +and can be reasonably considered independent and separate works in +themselves, then this License, and its terms, do not apply to those +sections when you distribute them as separate works. But when you +distribute the same sections as part of a whole which is a work based +on the Program, the distribution of the whole must be on the terms of +this License, whose permissions for other licensees extend to the +entire whole, and thus to each and every part regardless of who wrote it. + +Thus, it is not the intent of this section to claim rights or contest +your rights to work written entirely by you; rather, the intent is to +exercise the right to control the distribution of derivative or +collective works based on the Program. + +In addition, mere aggregation of another work not based on the Program +with the Program (or with a work based on the Program) on a volume of +a storage or distribution medium does not bring the other work under +the scope of this License. + + 3. You may copy and distribute the Program (or a work based on it, +under Section 2) in object code or executable form under the terms of +Sections 1 and 2 above provided that you also do one of the following: + + a) Accompany it with the complete corresponding machine-readable + source code, which must be distributed under the terms of Sections + 1 and 2 above on a medium customarily used for software interchange; or, + + b) Accompany it with a written offer, valid for at least three + years, to give any third party, for a charge no more than your + cost of physically performing source distribution, a complete + machine-readable copy of the corresponding source code, to be + distributed under the terms of Sections 1 and 2 above on a medium + customarily used for software interchange; or, + + c) Accompany it with the information you received as to the offer + to distribute corresponding source code. (This alternative is + allowed only for noncommercial distribution and only if you + received the program in object code or executable form with such + an offer, in accord with Subsection b above.) + +The source code for a work means the preferred form of the work for +making modifications to it. For an executable work, complete source +code means all the source code for all modules it contains, plus any +associated interface definition files, plus the scripts used to +control compilation and installation of the executable. However, as a +special exception, the source code distributed need not include +anything that is normally distributed (in either source or binary +form) with the major components (compiler, kernel, and so on) of the +operating system on which the executable runs, unless that component +itself accompanies the executable. + +If distribution of executable or object code is made by offering +access to copy from a designated place, then offering equivalent +access to copy the source code from the same place counts as +distribution of the source code, even though third parties are not +compelled to copy the source along with the object code. + + 4. You may not copy, modify, sublicense, or distribute the Program +except as expressly provided under this License. Any attempt +otherwise to copy, modify, sublicense or distribute the Program is +void, and will automatically terminate your rights under this License. +However, parties who have received copies, or rights, from you under +this License will not have their licenses terminated so long as such +parties remain in full compliance. + + 5. You are not required to accept this License, since you have not +signed it. However, nothing else grants you permission to modify or +distribute the Program or its derivative works. These actions are +prohibited by law if you do not accept this License. Therefore, by +modifying or distributing the Program (or any work based on the +Program), you indicate your acceptance of this License to do so, and +all its terms and conditions for copying, distributing or modifying +the Program or works based on it. + + 6. Each time you redistribute the Program (or any work based on the +Program), the recipient automatically receives a license from the +original licensor to copy, distribute or modify the Program subject to +these terms and conditions. You may not impose any further +restrictions on the recipients' exercise of the rights granted herein. +You are not responsible for enforcing compliance by third parties to +this License. + + 7. If, as a consequence of a court judgment or allegation of patent +infringement or for any other reason (not limited to patent issues), +conditions are imposed on you (whether by court order, agreement or +otherwise) that contradict the conditions of this License, they do not +excuse you from the conditions of this License. If you cannot +distribute so as to satisfy simultaneously your obligations under this +License and any other pertinent obligations, then as a consequence you +may not distribute the Program at all. For example, if a patent +license would not permit royalty-free redistribution of the Program by +all those who receive copies directly or indirectly through you, then +the only way you could satisfy both it and this License would be to +refrain entirely from distribution of the Program. + +If any portion of this section is held invalid or unenforceable under +any particular circumstance, the balance of the section is intended to +apply and the section as a whole is intended to apply in other +circumstances. + +It is not the purpose of this section to induce you to infringe any +patents or other property right claims or to contest validity of any +such claims; this section has the sole purpose of protecting the +integrity of the free software distribution system, which is +implemented by public license practices. Many people have made +generous contributions to the wide range of software distributed +through that system in reliance on consistent application of that +system; it is up to the author/donor to decide if he or she is willing +to distribute software through any other system and a licensee cannot +impose that choice. + +This section is intended to make thoroughly clear what is believed to +be a consequence of the rest of this License. + + 8. If the distribution and/or use of the Program is restricted in +certain countries either by patents or by copyrighted interfaces, the +original copyright holder who places the Program under this License +may add an explicit geographical distribution limitation excluding +those countries, so that distribution is permitted only in or among +countries not thus excluded. In such case, this License incorporates +the limitation as if written in the body of this License. + + 9. The Free Software Foundation may publish revised and/or new versions +of the General Public License from time to time. Such new versions will +be similar in spirit to the present version, but may differ in detail to +address new problems or concerns. + +Each version is given a distinguishing version number. If the Program +specifies a version number of this License which applies to it and "any +later version", you have the option of following the terms and conditions +either of that version or of any later version published by the Free +Software Foundation. If the Program does not specify a version number of +this License, you may choose any version ever published by the Free Software +Foundation. + + 10. If you wish to incorporate parts of the Program into other free +programs whose distribution conditions are different, write to the author +to ask for permission. For software which is copyrighted by the Free +Software Foundation, write to the Free Software Foundation; we sometimes +make exceptions for this. Our decision will be guided by the two goals +of preserving the free status of all derivatives of our free software and +of promoting the sharing and reuse of software generally. + + NO WARRANTY + + 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY +FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN +OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES +PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED +OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF +MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS +TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE +PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, +REPAIR OR CORRECTION. + + 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING +WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR +REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, +INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING +OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED +TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY +YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER +PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE +POSSIBILITY OF SUCH DAMAGES. diff --git a/Documentation/networking/Makefile b/Documentation/networking/Makefile index 5aba7a33aeeb..24c308dd3fd1 100644 --- a/Documentation/networking/Makefile +++ b/Documentation/networking/Makefile @@ -4,6 +4,8 @@ obj- := dummy.o # List of programs to build hostprogs-y := ifenslave +HOSTCFLAGS_ifenslave.o += -I$(objtree)/usr/include + # Tell kbuild to always build the programs always := $(hostprogs-y) diff --git a/Documentation/networking/batman-adv.txt b/Documentation/networking/batman-adv.txt new file mode 100644 index 000000000000..18afcd8afd51 --- /dev/null +++ b/Documentation/networking/batman-adv.txt @@ -0,0 +1,240 @@ +[state: 27-01-2011] + +BATMAN-ADV +---------- + +Batman advanced is a new approach to wireless networking which +does no longer operate on the IP basis. Unlike the batman daemon, +which exchanges information using UDP packets and sets routing +tables, batman-advanced operates on ISO/OSI Layer 2 only and uses +and routes (or better: bridges) Ethernet Frames. It emulates a +virtual network switch of all nodes participating. Therefore all +nodes appear to be link local, thus all higher operating proto- +cols won't be affected by any changes within the network. You can +run almost any protocol above batman advanced, prominent examples +are: IPv4, IPv6, DHCP, IPX. + +Batman advanced was implemented as a Linux kernel driver to re- +duce the overhead to a minimum. It does not depend on any (other) +network driver, and can be used on wifi as well as ethernet lan, +vpn, etc ... (anything with ethernet-style layer 2). + +CONFIGURATION +------------- + +Load the batman-adv module into your kernel: + +# insmod batman-adv.ko + +The module is now waiting for activation. You must add some in- +terfaces on which batman can operate. After loading the module +batman advanced will scan your systems interfaces to search for +compatible interfaces. Once found, it will create subfolders in +the /sys directories of each supported interface, e.g. + +# ls /sys/class/net/eth0/batman_adv/ +# iface_status mesh_iface + +If an interface does not have the "batman_adv" subfolder it prob- +ably is not supported. Not supported interfaces are: loopback, +non-ethernet and batman's own interfaces. + +Note: After the module was loaded it will continuously watch for +new interfaces to verify the compatibility. There is no need to +reload the module if you plug your USB wifi adapter into your ma- +chine after batman advanced was initially loaded. + +To activate a given interface simply write "bat0" into its +"mesh_iface" file inside the batman_adv subfolder: + +# echo bat0 > /sys/class/net/eth0/batman_adv/mesh_iface + +Repeat this step for all interfaces you wish to add. Now batman +starts using/broadcasting on this/these interface(s). + +By reading the "iface_status" file you can check its status: + +# cat /sys/class/net/eth0/batman_adv/iface_status +# active + +To deactivate an interface you have to write "none" into its +"mesh_iface" file: + +# echo none > /sys/class/net/eth0/batman_adv/mesh_iface + + +All mesh wide settings can be found in batman's own interface +folder: + +# ls /sys/class/net/bat0/mesh/ +# aggregated_ogms gw_bandwidth hop_penalty +# bonding gw_mode orig_interval +# fragmentation gw_sel_class vis_mode + + +There is a special folder for debugging informations: + +# ls /sys/kernel/debug/batman_adv/bat0/ +# gateways socket transtable_global vis_data +# originators softif_neigh transtable_local + + +Some of the files contain all sort of status information regard- +ing the mesh network. For example, you can view the table of +originators (mesh participants) with: + +# cat /sys/kernel/debug/batman_adv/bat0/originators + +Other files allow to change batman's behaviour to better fit your +requirements. For instance, you can check the current originator +interval (value in milliseconds which determines how often batman +sends its broadcast packets): + +# cat /sys/class/net/bat0/mesh/orig_interval +# 1000 + +and also change its value: + +# echo 3000 > /sys/class/net/bat0/mesh/orig_interval + +In very mobile scenarios, you might want to adjust the originator +interval to a lower value. This will make the mesh more respon- +sive to topology changes, but will also increase the overhead. + + +USAGE +----- + +To make use of your newly created mesh, batman advanced provides +a new interface "bat0" which you should use from this point on. +All interfaces added to batman advanced are not relevant any +longer because batman handles them for you. Basically, one "hands +over" the data by using the batman interface and batman will make +sure it reaches its destination. + +The "bat0" interface can be used like any other regular inter- +face. It needs an IP address which can be either statically con- +figured or dynamically (by using DHCP or similar services): + +# NodeA: ifconfig bat0 192.168.0.1 +# NodeB: ifconfig bat0 192.168.0.2 +# NodeB: ping 192.168.0.1 + +Note: In order to avoid problems remove all IP addresses previ- +ously assigned to interfaces now used by batman advanced, e.g. + +# ifconfig eth0 0.0.0.0 + + +VISUALIZATION +------------- + +If you want topology visualization, at least one mesh node must +be configured as VIS-server: + +# echo "server" > /sys/class/net/bat0/mesh/vis_mode + +Each node is either configured as "server" or as "client" (de- +fault: "client"). Clients send their topology data to the server +next to them, and server synchronize with other servers. If there +is no server configured (default) within the mesh, no topology +information will be transmitted. With these "synchronizing +servers", there can be 1 or more vis servers sharing the same (or +at least very similar) data. + +When configured as server, you can get a topology snapshot of +your mesh: + +# cat /sys/kernel/debug/batman_adv/bat0/vis_data + +This raw output is intended to be easily parsable and convertable +with other tools. Have a look at the batctl README if you want a +vis output in dot or json format for instance and how those out- +puts could then be visualised in an image. + +The raw format consists of comma separated values per entry where +each entry is giving information about a certain source inter- +face. Each entry can/has to have the following values: +-> "mac" - mac address of an originator's source interface + (each line begins with it) +-> "TQ mac value" - src mac's link quality towards mac address + of a neighbor originator's interface which + is being used for routing +-> "HNA mac" - HNA announced by source mac +-> "PRIMARY" - this is a primary interface +-> "SEC mac" - secondary mac address of source + (requires preceding PRIMARY) + +The TQ value has a range from 4 to 255 with 255 being the best. +The HNA entries are showing which hosts are connected to the mesh +via bat0 or being bridged into the mesh network. The PRIMARY/SEC +values are only applied on primary interfaces + + +LOGGING/DEBUGGING +----------------- + +All error messages, warnings and information messages are sent to +the kernel log. Depending on your operating system distribution +this can be read in one of a number of ways. Try using the com- +mands: dmesg, logread, or looking in the files /var/log/kern.log +or /var/log/syslog. All batman-adv messages are prefixed with +"batman-adv:" So to see just these messages try + +# dmesg | grep batman-adv + +When investigating problems with your mesh network it is some- +times necessary to see more detail debug messages. This must be +enabled when compiling the batman-adv module. When building bat- +man-adv as part of kernel, use "make menuconfig" and enable the +option "B.A.T.M.A.N. debugging". + +Those additional debug messages can be accessed using a special +file in debugfs + +# cat /sys/kernel/debug/batman_adv/bat0/log + +The additional debug output is by default disabled. It can be en- +abled during run time. Following log_levels are defined: + +0 - All debug output disabled +1 - Enable messages related to routing / flooding / broadcasting +2 - Enable route or hna added / changed / deleted +3 - Enable all messages + +The debug output can be changed at runtime using the file +/sys/class/net/bat0/mesh/log_level. e.g. + +# echo 2 > /sys/class/net/bat0/mesh/log_level + +will enable debug messages for when routes or HNAs change. + + +BATCTL +------ + +As batman advanced operates on layer 2 all hosts participating in +the virtual switch are completely transparent for all protocols +above layer 2. Therefore the common diagnosis tools do not work +as expected. To overcome these problems batctl was created. At +the moment the batctl contains ping, traceroute, tcpdump and +interfaces to the kernel module settings. + +For more information, please see the manpage (man batctl). + +batctl is available on http://www.open-mesh.org/ + + +CONTACT +------- + +Please send us comments, experiences, questions, anything :) + +IRC: #batman on irc.freenode.org +Mailing-list: b.a.t.m.a.n@open-mesh.org (optional subscription + at https://lists.open-mesh.org/mm/listinfo/b.a.t.m.a.n) + +You can also contact the Authors: + +Marek Lindner <lindner_marek@yahoo.de> +Simon Wunderlich <siwu@hrz.tu-chemnitz.de> diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt index 5dc638791d97..b36e741e94db 100644 --- a/Documentation/networking/bonding.txt +++ b/Documentation/networking/bonding.txt @@ -49,7 +49,8 @@ Table of Contents 3.3 Configuring Bonding Manually with Ifenslave 3.3.1 Configuring Multiple Bonds Manually 3.4 Configuring Bonding Manually via Sysfs -3.5 Overriding Configuration for Special Cases +3.5 Configuration with Interfaces Support +3.6 Overriding Configuration for Special Cases 4. Querying Bonding Configuration 4.1 Bonding Configuration @@ -161,8 +162,8 @@ onwards) do not have /usr/include/linux symbolically linked to the default kernel source include directory. SECOND IMPORTANT NOTE: - If you plan to configure bonding using sysfs, you do not need -to use ifenslave. + If you plan to configure bonding using sysfs or using the +/etc/network/interfaces file, you do not need to use ifenslave. 2. Bonding Driver Options ========================= @@ -779,22 +780,26 @@ resend_igmp You can configure bonding using either your distro's network initialization scripts, or manually using either ifenslave or the -sysfs interface. Distros generally use one of two packages for the -network initialization scripts: initscripts or sysconfig. Recent -versions of these packages have support for bonding, while older +sysfs interface. Distros generally use one of three packages for the +network initialization scripts: initscripts, sysconfig or interfaces. +Recent versions of these packages have support for bonding, while older versions do not. We will first describe the options for configuring bonding for -distros using versions of initscripts and sysconfig with full or -partial support for bonding, then provide information on enabling +distros using versions of initscripts, sysconfig and interfaces with full +or partial support for bonding, then provide information on enabling bonding without support from the network initialization scripts (i.e., older versions of initscripts or sysconfig). - If you're unsure whether your distro uses sysconfig or -initscripts, or don't know if it's new enough, have no fear. + If you're unsure whether your distro uses sysconfig, +initscripts or interfaces, or don't know if it's new enough, have no fear. Determining this is fairly straightforward. - First, issue the command: + First, look for a file called interfaces in /etc/network directory. +If this file is present in your system, then your system use interfaces. See +Configuration with Interfaces Support. + + Else, issue the command: $ rpm -qf /sbin/ifup @@ -1327,8 +1332,62 @@ echo 2000 > /sys/class/net/bond1/bonding/arp_interval echo +eth2 > /sys/class/net/bond1/bonding/slaves echo +eth3 > /sys/class/net/bond1/bonding/slaves -3.5 Overriding Configuration for Special Cases +3.5 Configuration with Interfaces Support +----------------------------------------- + + This section applies to distros which use /etc/network/interfaces file +to describe network interface configuration, most notably Debian and it's +derivatives. + + The ifup and ifdown commands on Debian don't support bonding out of +the box. The ifenslave-2.6 package should be installed to provide bonding +support. Once installed, this package will provide bond-* options to be used +into /etc/network/interfaces. + + Note that ifenslave-2.6 package will load the bonding module and use +the ifenslave command when appropriate. + +Example Configurations +---------------------- + +In /etc/network/interfaces, the following stanza will configure bond0, in +active-backup mode, with eth0 and eth1 as slaves. + +auto bond0 +iface bond0 inet dhcp + bond-slaves eth0 eth1 + bond-mode active-backup + bond-miimon 100 + bond-primary eth0 eth1 + +If the above configuration doesn't work, you might have a system using +upstart for system startup. This is most notably true for recent +Ubuntu versions. The following stanza in /etc/network/interfaces will +produce the same result on those systems. + +auto bond0 +iface bond0 inet dhcp + bond-slaves none + bond-mode active-backup + bond-miimon 100 + +auto eth0 +iface eth0 inet manual + bond-master bond0 + bond-primary eth0 eth1 + +auto eth1 +iface eth1 inet manual + bond-master bond0 + bond-primary eth0 eth1 + +For a full list of bond-* supported options in /etc/network/interfaces and some +more advanced examples tailored to you particular distros, see the files in +/usr/share/doc/ifenslave-2.6. + +3.6 Overriding Configuration for Special Cases ---------------------------------------------- + When using the bonding driver, the physical port which transmits a frame is typically selected by the bonding driver, and is not relevant to the user or system administrator. The output port is simply selected using the policies of @@ -2499,18 +2558,15 @@ enslaved. 16. Resources and Links ======================= -The latest version of the bonding driver can be found in the latest + The latest version of the bonding driver can be found in the latest version of the linux kernel, found on http://kernel.org -The latest version of this document can be found in either the latest -kernel source (named Documentation/networking/bonding.txt), or on the -bonding sourceforge site: - -http://www.sourceforge.net/projects/bonding + The latest version of this document can be found in the latest kernel +source (named Documentation/networking/bonding.txt). -Discussions regarding the bonding driver take place primarily on the -bonding-devel mailing list, hosted at sourceforge.net. If you have -questions or problems, post them to the list. The list address is: + Discussions regarding the usage of the bonding driver take place on the +bonding-devel mailing list, hosted at sourceforge.net. If you have questions or +problems, post them to the list. The list address is: bonding-devel@lists.sourceforge.net @@ -2519,6 +2575,17 @@ be found at: https://lists.sourceforge.net/lists/listinfo/bonding-devel + Discussions regarding the developpement of the bonding driver take place +on the main Linux network mailing list, hosted at vger.kernel.org. The list +address is: + +netdev@vger.kernel.org + + The administrative interface (to subscribe or unsubscribe) can +be found at: + +http://vger.kernel.org/vger-lists.html#netdev + Donald Becker's Ethernet Drivers and diag programs may be found at : - http://web.archive.org/web/*/http://www.scyld.com/network/ diff --git a/Documentation/networking/bridge.txt b/Documentation/networking/bridge.txt index bec69a8a1697..a7ba5e4e2c91 100644 --- a/Documentation/networking/bridge.txt +++ b/Documentation/networking/bridge.txt @@ -1,8 +1,8 @@ In order to use the Ethernet bridging functionality, you'll need the userspace tools. These programs and documentation are available -at http://www.linux-foundation.org/en/Net:Bridge. The download page is +at http://www.linuxfoundation.org/en/Net:Bridge. The download page is http://prdownloads.sourceforge.net/bridge. If you still have questions, don't hesitate to post to the mailing list -(more info http://lists.osdl.org/mailman/listinfo/bridge). +(more info https://lists.linux-foundation.org/mailman/listinfo/bridge). diff --git a/Documentation/networking/caif/spi_porting.txt b/Documentation/networking/caif/spi_porting.txt index 61d7c9247453..0cb8cb9098f4 100644 --- a/Documentation/networking/caif/spi_porting.txt +++ b/Documentation/networking/caif/spi_porting.txt @@ -32,7 +32,7 @@ the physical hardware, both with regard to SPI and to GPIOs. This function is called by the CAIF SPI interface to give you a chance to set up your hardware to be ready to receive a stream of data from the master. The xfer structure contains - both physical and logical adresses, as well as the total length + both physical and logical addresses, as well as the total length of the transfer in both directions.The dev parameter can be used to map to different CAIF SPI slave devices. diff --git a/Documentation/networking/dccp.txt b/Documentation/networking/dccp.txt index 271d524a4c8d..d718bc2ff1cf 100644 --- a/Documentation/networking/dccp.txt +++ b/Documentation/networking/dccp.txt @@ -38,15 +38,35 @@ The Linux DCCP implementation does not currently support all the features that a specified in RFCs 4340...42. The known bugs are at: - http://linux-net.osdl.org/index.php/TODO#DCCP + http://www.linuxfoundation.org/collaborate/workgroups/networking/todo#DCCP For more up-to-date versions of the DCCP implementation, please consider using the experimental DCCP test tree; instructions for checking this out are on: -http://linux-net.osdl.org/index.php/DCCP_Testing#Experimental_DCCP_source_tree +http://www.linuxfoundation.org/collaborate/workgroups/networking/dccp_testing#Experimental_DCCP_source_tree Socket options ============== +DCCP_SOCKOPT_QPOLICY_ID sets the dequeuing policy for outgoing packets. It takes +a policy ID as argument and can only be set before the connection (i.e. changes +during an established connection are not supported). Currently, two policies are +defined: the "simple" policy (DCCPQ_POLICY_SIMPLE), which does nothing special, +and a priority-based variant (DCCPQ_POLICY_PRIO). The latter allows to pass an +u32 priority value as ancillary data to sendmsg(), where higher numbers indicate +a higher packet priority (similar to SO_PRIORITY). This ancillary data needs to +be formatted using a cmsg(3) message header filled in as follows: + cmsg->cmsg_level = SOL_DCCP; + cmsg->cmsg_type = DCCP_SCM_PRIORITY; + cmsg->cmsg_len = CMSG_LEN(sizeof(uint32_t)); /* or CMSG_LEN(4) */ + +DCCP_SOCKOPT_QPOLICY_TXQLEN sets the maximum length of the output queue. A zero +value is always interpreted as unbounded queue length. If different from zero, +the interpretation of this parameter depends on the current dequeuing policy +(see above): the "simple" policy will enforce a fixed queue size by returning +EAGAIN, whereas the "prio" policy enforces a fixed queue length by dropping the +lowest-priority packet first. The default value for this parameter is +initialised from /proc/sys/net/dccp/default/tx_qlen. + DCCP_SOCKOPT_SERVICE sets the service. The specification mandates use of service codes (RFC 4340, sec. 8.1.2); if this socket option is not set, the socket will fall back to 0 (which means that no meaningful service code @@ -147,6 +167,7 @@ rx_ccid = 2 seq_window = 100 The initial sequence window (sec. 7.5.2) of the sender. This influences the local ackno validity and the remote seqno validity windows (7.5.1). + Values in the range Wmin = 32 (RFC 4340, 7.5.2) up to 2^32-1 can be set. tx_qlen = 5 The size of the transmit buffer in packets. A value of 0 corresponds diff --git a/Documentation/networking/dns_resolver.txt b/Documentation/networking/dns_resolver.txt index aefd1e681804..04ca06325b08 100644 --- a/Documentation/networking/dns_resolver.txt +++ b/Documentation/networking/dns_resolver.txt @@ -61,7 +61,6 @@ before the more general line given above as the first match is the one taken. create dns_resolver foo:* * /usr/sbin/dns.foo %k - ===== USAGE ===== @@ -104,6 +103,14 @@ implemented in the module can be called after doing: returned also. +=============================== +READING DNS KEYS FROM USERSPACE +=============================== + +Keys of dns_resolver type can be read from userspace using keyctl_read() or +"keyctl read/print/pipe". + + ========= MECHANISM ========= diff --git a/Documentation/networking/e100.txt b/Documentation/networking/e100.txt index 944aa55e79f8..162f323a7a1f 100644 --- a/Documentation/networking/e100.txt +++ b/Documentation/networking/e100.txt @@ -72,7 +72,7 @@ Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data ethtool -G eth? tx n, where n is the number of desired tx descriptors. Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by - default. Ethtool can be used as follows to force speed/duplex. + default. The ethtool utility can be used as follows to force speed/duplex. ethtool -s eth? autoneg off speed {10|100} duplex {full|half} @@ -126,30 +126,21 @@ Additional Configurations ------- The driver utilizes the ethtool interface for driver configuration and - diagnostics, as well as displaying statistical information. Ethtool + diagnostics, as well as displaying statistical information. The ethtool version 1.6 or later is required for this functionality. The latest release of ethtool can be found from - http://sourceforge.net/projects/gkernel. - - NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support - for a more complete ethtool feature set can be enabled by upgrading - ethtool to ethtool-1.8.1. - + http://ftp.kernel.org/pub/software/network/ethtool/ Enabling Wake on LAN* (WoL) --------------------------- - WoL is provided through the Ethtool* utility. Ethtool is included with Red - Hat* 8.0. For other Linux distributions, download and install Ethtool from - the following website: http://sourceforge.net/projects/gkernel. - - For instructions on enabling WoL with Ethtool, refer to the Ethtool man page. + WoL is provided through the ethtool* utility. For instructions on enabling + WoL with ethtool, refer to the ethtool man page. WoL will be enabled on the system during the next shut down or reboot. For this driver version, in order to enable WoL, the e100 driver must be loaded when shutting down or rebooting the system. - NAPI ---- diff --git a/Documentation/networking/e1000.txt b/Documentation/networking/e1000.txt index d9271e74e488..71ca95855671 100644 --- a/Documentation/networking/e1000.txt +++ b/Documentation/networking/e1000.txt @@ -79,7 +79,7 @@ InterruptThrottleRate --------------------- (not supported on Intel(R) 82542, 82543 or 82544-based adapters) Valid Range: 0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative, - 4=simplified balancing) + 4=simplified balancing) Default Value: 3 The driver can limit the amount of interrupts per second that the adapter @@ -124,8 +124,8 @@ InterruptThrottleRate is set to mode 1. In this mode, which operates the same as mode 3, the InterruptThrottleRate will be increased stepwise to 70000 for traffic in class "Lowest latency". -In simplified mode the interrupt rate is based on the ratio of Tx and -Rx traffic. If the bytes per second rate is approximately equal, the +In simplified mode the interrupt rate is based on the ratio of TX and +RX traffic. If the bytes per second rate is approximately equal, the interrupt rate will drop as low as 2000 interrupts per second. If the traffic is mostly transmit or mostly receive, the interrupt rate could be as high as 8000. @@ -245,7 +245,7 @@ NOTE: Depending on the available system resources, the request for a TxDescriptorStep ---------------- Valid Range: 1 (use every Tx Descriptor) - 4 (use every 4th Tx Descriptor) + 4 (use every 4th Tx Descriptor) Default Value: 1 (use every Tx Descriptor) @@ -312,7 +312,7 @@ Valid Range: 0-xxxxxxx (0=off) Default Value: 256 Usage: insmod e1000.ko copybreak=128 -Driver copies all packets below or equaling this size to a fresh Rx +Driver copies all packets below or equaling this size to a fresh RX buffer before handing it up the stack. This parameter is different than other parameters, in that it is a @@ -431,15 +431,15 @@ Additional Configurations Ethtool ------- The driver utilizes the ethtool interface for driver configuration and - diagnostics, as well as displaying statistical information. Ethtool + diagnostics, as well as displaying statistical information. The ethtool version 1.6 or later is required for this functionality. The latest release of ethtool can be found from - http://sourceforge.net/projects/gkernel. + http://ftp.kernel.org/pub/software/network/ethtool/ Enabling Wake on LAN* (WoL) --------------------------- - WoL is configured through the Ethtool* utility. + WoL is configured through the ethtool* utility. WoL will be enabled on the system during the next shut down or reboot. For this driver version, in order to enable WoL, the e1000 driver must be diff --git a/Documentation/networking/e1000e.txt b/Documentation/networking/e1000e.txt index 6aa048badf32..97b5ba942ebf 100644 --- a/Documentation/networking/e1000e.txt +++ b/Documentation/networking/e1000e.txt @@ -1,5 +1,5 @@ Linux* Driver for Intel(R) Network Connection -=============================================================== +============================================= Intel Gigabit Linux driver. Copyright(c) 1999 - 2010 Intel Corporation. @@ -61,6 +61,12 @@ per second, even if more packets have come in. This reduces interrupt load on the system and can lower CPU utilization under heavy load, but will increase latency as packets are not processed as quickly. +The default behaviour of the driver previously assumed a static +InterruptThrottleRate value of 8000, providing a good fallback value for +all traffic types, but lacking in small packet performance and latency. +The hardware can handle many more small packets per second however, and +for this reason an adaptive interrupt moderation algorithm was implemented. + The driver has two adaptive modes (setting 1 or 3) in which it dynamically adjusts the InterruptThrottleRate value based on the traffic that it receives. After determining the type of incoming traffic in the last @@ -86,8 +92,8 @@ InterruptThrottleRate is set to mode 1. In this mode, which operates the same as mode 3, the InterruptThrottleRate will be increased stepwise to 70000 for traffic in class "Lowest latency". -In simplified mode the interrupt rate is based on the ratio of Tx and -Rx traffic. If the bytes per second rate is approximately equal the +In simplified mode the interrupt rate is based on the ratio of TX and +RX traffic. If the bytes per second rate is approximately equal, the interrupt rate will drop as low as 2000 interrupts per second. If the traffic is mostly transmit or mostly receive, the interrupt rate could be as high as 8000. @@ -177,7 +183,7 @@ Copybreak Valid Range: 0-xxxxxxx (0=off) Default Value: 256 -Driver copies all packets below or equaling this size to a fresh Rx +Driver copies all packets below or equaling this size to a fresh RX buffer before handing it up the stack. This parameter is different than other parameters, in that it is a @@ -223,17 +229,17 @@ loading or enabling the driver, try disabling this feature. WriteProtectNVM --------------- -Valid Range: 0-1 -Default Value: 1 (enabled) - -Set the hardware to ignore all write/erase cycles to the GbE region in the -ICHx NVM (non-volatile memory). This feature can be disabled by the -WriteProtectNVM module parameter (enabled by default) only after a hardware -reset, but the machine must be power cycled before trying to enable writes. - -Note: the kernel boot option iomem=relaxed may need to be set if the kernel -config option CONFIG_STRICT_DEVMEM=y, if the root user wants to write the -NVM from user space via ethtool. +Valid Range: 0,1 +Default Value: 1 + +If set to 1, configure the hardware to ignore all write/erase cycles to the +GbE region in the ICHx NVM (in order to prevent accidental corruption of the +NVM). This feature can be disabled by setting the parameter to 0 during initial +driver load. +NOTE: The machine must be power cycled (full off/on) when enabling NVM writes +via setting the parameter to zero. Once the NVM has been locked (via the +parameter at 1 when the driver loads) it cannot be unlocked except via power +cycle. Additional Configurations ========================= @@ -259,32 +265,30 @@ Additional Configurations - Some adapters limit Jumbo Frames sized packets to a maximum of 4096 bytes and some adapters do not support Jumbo Frames. - Ethtool ------- The driver utilizes the ethtool interface for driver configuration and diagnostics, as well as displaying statistical information. We - strongly recommend downloading the latest version of Ethtool at: + strongly recommend downloading the latest version of ethtool at: - http://sourceforge.net/projects/gkernel. + http://ftp.kernel.org/pub/software/network/ethtool/ Speed and Duplex ---------------- - Speed and Duplex are configured through the Ethtool* utility. For - instructions, refer to the Ethtool man page. + Speed and Duplex are configured through the ethtool* utility. For + instructions, refer to the ethtool man page. Enabling Wake on LAN* (WoL) --------------------------- - WoL is configured through the Ethtool* utility. For instructions on - enabling WoL with Ethtool, refer to the Ethtool man page. + WoL is configured through the ethtool* utility. For instructions on + enabling WoL with ethtool, refer to the ethtool man page. WoL will be enabled on the system during the next shut down or reboot. For this driver version, in order to enable WoL, the e1000e driver must be loaded when shutting down or rebooting the system. In most cases Wake On LAN is only supported on port A for multiple port - adapters. To verify if a port supports Wake on LAN run ethtool eth<X>. - + adapters. To verify if a port supports Wake on Lan run ethtool eth<X>. Support ======= diff --git a/Documentation/networking/generic_netlink.txt b/Documentation/networking/generic_netlink.txt index d4f8b8b9b53c..3e071115ca90 100644 --- a/Documentation/networking/generic_netlink.txt +++ b/Documentation/networking/generic_netlink.txt @@ -1,3 +1,3 @@ A wiki document on how to use Generic Netlink can be found here: - * http://linux-net.osdl.org/index.php/Generic_Netlink_HOWTO + * http://www.linuxfoundation.org/collaborate/workgroups/networking/generic_netlink_howto diff --git a/Documentation/networking/igb.txt b/Documentation/networking/igb.txt index ab2d71831892..98953c0d5342 100644 --- a/Documentation/networking/igb.txt +++ b/Documentation/networking/igb.txt @@ -36,6 +36,7 @@ Default Value: 0 This parameter adds support for SR-IOV. It causes the driver to spawn up to max_vfs worth of virtual function. + Additional Configurations ========================= @@ -60,15 +61,16 @@ Additional Configurations Ethtool ------- The driver utilizes the ethtool interface for driver configuration and - diagnostics, as well as displaying statistical information. + diagnostics, as well as displaying statistical information. The latest + version of ethtool can be found at: - http://sourceforge.net/projects/gkernel. + http://ftp.kernel.org/pub/software/network/ethtool/ Enabling Wake on LAN* (WoL) --------------------------- - WoL is configured through the Ethtool* utility. + WoL is configured through the ethtool* utility. - For instructions on enabling WoL with Ethtool, refer to the Ethtool man page. + For instructions on enabling WoL with ethtool, refer to the ethtool man page. WoL will be enabled on the system during the next shut down or reboot. For this driver version, in order to enable WoL, the igb driver must be @@ -91,31 +93,6 @@ Additional Configurations REQUIREMENTS: MSI-X support is required for Multiqueue. If MSI-X is not found, the system will fallback to MSI or to Legacy interrupts. - LRO - --- - Large Receive Offload (LRO) is a technique for increasing inbound throughput - of high-bandwidth network connections by reducing CPU overhead. It works by - aggregating multiple incoming packets from a single stream into a larger - buffer before they are passed higher up the networking stack, thus reducing - the number of packets that have to be processed. LRO combines multiple - Ethernet frames into a single receive in the stack, thereby potentially - decreasing CPU utilization for receives. - - NOTE: You need to have inet_lro enabled via either the CONFIG_INET_LRO or - CONFIG_INET_LRO_MODULE kernel config option. Additionally, if - CONFIG_INET_LRO_MODULE is used, the inet_lro module needs to be loaded - before the igb driver. - - You can verify that the driver is using LRO by looking at these counters in - Ethtool: - - lro_aggregated - count of total packets that were combined - lro_flushed - counts the number of packets flushed out of LRO - lro_no_desc - counts the number of times an LRO descriptor was not available - for the LRO packet - - NOTE: IPv6 and UDP are not supported by LRO. - Support ======= diff --git a/Documentation/networking/igbvf.txt b/Documentation/networking/igbvf.txt index 056028138d9c..cbfe4ee65533 100644 --- a/Documentation/networking/igbvf.txt +++ b/Documentation/networking/igbvf.txt @@ -58,9 +58,11 @@ Additional Configurations Ethtool ------- The driver utilizes the ethtool interface for driver configuration and - diagnostics, as well as displaying statistical information. + diagnostics, as well as displaying statistical information. The ethtool + version 3.0 or later is required for this functionality, although we + strongly recommend downloading the latest version at: - http://sourceforge.net/projects/gkernel. + http://ftp.kernel.org/pub/software/network/ethtool/ Support ======= diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index 3c5e465296e1..d3d653a5f9b9 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -11,7 +11,9 @@ ip_forward - BOOLEAN for routers) ip_default_ttl - INTEGER - default 64 + Default value of TTL field (Time To Live) for outgoing (but not + forwarded) IP packets. Should be between 1 and 255 inclusive. + Default: 64 (as recommended by RFC1700) ip_no_pmtu_disc - BOOLEAN Disable Path MTU Discovery. @@ -185,7 +187,7 @@ tcp_cookie_size - INTEGER tcp_dsack - BOOLEAN Allows TCP to send "duplicate" SACKs. -tcp_ecn - BOOLEAN +tcp_ecn - INTEGER Enable Explicit Congestion Notification (ECN) in TCP. ECN is only used when both ends of the TCP flow support it. It is useful to avoid losses due to congestion (when the bottleneck router supports @@ -278,6 +280,17 @@ tcp_max_orphans - INTEGER more aggressively. Let me to remind again: each orphan eats up to ~64K of unswappable memory. +tcp_max_ssthresh - INTEGER + Limited Slow-Start for TCP with large congestion windows (cwnd) defined in + RFC3742. Limited slow-start is a mechanism to limit growth of the cwnd + on the region where cwnd is larger than tcp_max_ssthresh. TCP increases cwnd + by at most tcp_max_ssthresh segments, and by at least tcp_max_ssthresh/2 + segments per RTT when the cwnd is above tcp_max_ssthresh. + If TCP connection increased cwnd to thousands (or tens of thousands) segments, + and thousands of packets were being dropped during slow-start, you can set + tcp_max_ssthresh to improve performance for new TCP connection. + Default: 0 (off) + tcp_max_syn_backlog - INTEGER Maximal number of remembered connection requests, which are still did not receive an acknowledgment from connecting client. @@ -708,10 +721,28 @@ igmp_max_memberships - INTEGER Change the maximum number of multicast groups we can subscribe to. Default: 20 -conf/interface/* changes special settings per interface (where "interface" is - the name of your network interface) -conf/all/* is special, changes the settings for all interfaces + Theoretical maximum value is bounded by having to send a membership + report in a single datagram (i.e. the report can't span multiple + datagrams, or risk confusing the switch and leaving groups you don't + intend to). + + The number of supported groups 'M' is bounded by the number of group + report entries you can fit into a single datagram of 65535 bytes. + + M = 65536-sizeof (ip header)/(sizeof(Group record)) + + Group records are variable length, with a minimum of 12 bytes. + So net.ipv4.igmp_max_memberships should not be set higher than: + + (65536-24) / 12 = 5459 + + The value 5459 assumes no IP header options, so in practice + this number may be lower. + + conf/interface/* changes special settings per interface (where + "interface" is the name of your network interface) + conf/all/* is special, changes the settings for all interfaces log_martians - BOOLEAN Log packets with impossible addresses to kernel log. diff --git a/Documentation/networking/ixgb.txt b/Documentation/networking/ixgb.txt index a0d0ffb5e584..e196f16df313 100644 --- a/Documentation/networking/ixgb.txt +++ b/Documentation/networking/ixgb.txt @@ -309,15 +309,15 @@ Additional Configurations Ethtool ------- The driver utilizes the ethtool interface for driver configuration and - diagnostics, as well as displaying statistical information. Ethtool + diagnostics, as well as displaying statistical information. The ethtool version 1.6 or later is required for this functionality. The latest release of ethtool can be found from - http://sourceforge.net/projects/gkernel + http://ftp.kernel.org/pub/software/network/ethtool/ - NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support - for a more complete ethtool feature set can be enabled by upgrading - to the latest version. + NOTE: The ethtool version 1.6 only supports a limited set of ethtool options. + Support for a more complete ethtool feature set can be enabled by + upgrading to the latest version. NAPI diff --git a/Documentation/networking/ixgbe.txt b/Documentation/networking/ixgbe.txt index eeb68685c788..af77ed3c4172 100644 --- a/Documentation/networking/ixgbe.txt +++ b/Documentation/networking/ixgbe.txt @@ -1,107 +1,126 @@ Linux Base Driver for 10 Gigabit PCI Express Intel(R) Network Connection ======================================================================== -March 10, 2009 - +Intel Gigabit Linux driver. +Copyright(c) 1999 - 2010 Intel Corporation. Contents ======== -- In This Release - Identifying Your Adapter -- Building and Installation - Additional Configurations +- Performance Tuning +- Known Issues - Support +Identifying Your Adapter +======================== +The driver in this release is compatible with 82598 and 82599-based Intel +Network Connections. -In This Release -=============== +For more information on how to identify your adapter, go to the Adapter & +Driver ID Guide at: -This file describes the ixgbe Linux Base Driver for the 10 Gigabit PCI -Express Intel(R) Network Connection. This driver includes support for -Itanium(R)2-based systems. + http://support.intel.com/support/network/sb/CS-012904.htm -For questions related to hardware requirements, refer to the documentation -supplied with your 10 Gigabit adapter. All hardware requirements listed apply -to use with Linux. +SFP+ Devices with Pluggable Optics +---------------------------------- -The following features are available in this kernel: - - Native VLANs - - Channel Bonding (teaming) - - SNMP - - Generic Receive Offload - - Data Center Bridging +82599-BASED ADAPTERS -Channel Bonding documentation can be found in the Linux kernel source: -/Documentation/networking/bonding.txt +NOTES: If your 82599-based Intel(R) Network Adapter came with Intel optics, or +is an Intel(R) Ethernet Server Adapter X520-2, then it only supports Intel +optics and/or the direct attach cables listed below. -Ethtool, lspci, and ifconfig can be used to display device and driver -specific information. +When 82599-based SFP+ devices are connected back to back, they should be set to +the same Speed setting via ethtool. Results may vary if you mix speed settings. +82598-based adapters support all passive direct attach cables that comply +with SFF-8431 v4.1 and SFF-8472 v10.4 specifications. Active direct attach +cables are not supported. +Supplier Type Part Numbers -Identifying Your Adapter -======================== +SR Modules +Intel DUAL RATE 1G/10G SFP+ SR (bailed) FTLX8571D3BCV-IT +Intel DUAL RATE 1G/10G SFP+ SR (bailed) AFBR-703SDDZ-IN1 +Intel DUAL RATE 1G/10G SFP+ SR (bailed) AFBR-703SDZ-IN2 +LR Modules +Intel DUAL RATE 1G/10G SFP+ LR (bailed) FTLX1471D3BCV-IT +Intel DUAL RATE 1G/10G SFP+ LR (bailed) AFCT-701SDDZ-IN1 +Intel DUAL RATE 1G/10G SFP+ LR (bailed) AFCT-701SDZ-IN2 -This driver supports devices based on the 82598 controller and the 82599 -controller. +The following is a list of 3rd party SFP+ modules and direct attach cables that +have received some testing. Not all modules are applicable to all devices. -For specific information on identifying which adapter you have, please visit: +Supplier Type Part Numbers - http://support.intel.com/support/network/sb/CS-008441.htm +Finisar SFP+ SR bailed, 10g single rate FTLX8571D3BCL +Avago SFP+ SR bailed, 10g single rate AFBR-700SDZ +Finisar SFP+ LR bailed, 10g single rate FTLX1471D3BCL +Finisar DUAL RATE 1G/10G SFP+ SR (No Bail) FTLX8571D3QCV-IT +Avago DUAL RATE 1G/10G SFP+ SR (No Bail) AFBR-703SDZ-IN1 +Finisar DUAL RATE 1G/10G SFP+ LR (No Bail) FTLX1471D3QCV-IT +Avago DUAL RATE 1G/10G SFP+ LR (No Bail) AFCT-701SDZ-IN1 +Finistar 1000BASE-T SFP FCLF8522P2BTL +Avago 1000BASE-T SFP ABCU-5710RZ -Building and Installation -========================= +82599-based adapters support all passive and active limiting direct attach +cables that comply with SFF-8431 v4.1 and SFF-8472 v10.4 specifications. -select m for "Intel(R) 10GbE PCI Express adapters support" located at: - Location: - -> Device Drivers - -> Network device support (NETDEVICES [=y]) - -> Ethernet (10000 Mbit) (NETDEV_10000 [=y]) +Laser turns off for SFP+ when ifconfig down +------------------------------------------- +"ifconfig down" turns off the laser for 82599-based SFP+ fiber adapters. +"ifconfig up" turns on the later. -1. make modules & make modules_install -2. Load the module: +82598-BASED ADAPTERS -# modprobe ixgbe +NOTES for 82598-Based Adapters: +- Intel(R) Network Adapters that support removable optical modules only support + their original module type (i.e., the Intel(R) 10 Gigabit SR Dual Port + Express Module only supports SR optical modules). If you plug in a different + type of module, the driver will not load. +- Hot Swapping/hot plugging optical modules is not supported. +- Only single speed, 10 gigabit modules are supported. +- LAN on Motherboard (LOMs) may support DA, SR, or LR modules. Other module + types are not supported. Please see your system documentation for details. - The insmod command can be used if the full - path to the driver module is specified. For example: +The following is a list of 3rd party SFP+ modules and direct attach cables that +have received some testing. Not all modules are applicable to all devices. - insmod /lib/modules/<KERNEL VERSION>/kernel/drivers/net/ixgbe/ixgbe.ko +Supplier Type Part Numbers - With 2.6 based kernels also make sure that older ixgbe drivers are - removed from the kernel, before loading the new module: +Finisar SFP+ SR bailed, 10g single rate FTLX8571D3BCL +Avago SFP+ SR bailed, 10g single rate AFBR-700SDZ +Finisar SFP+ LR bailed, 10g single rate FTLX1471D3BCL - rmmod ixgbe; modprobe ixgbe +82598-based adapters support all passive direct attach cables that comply +with SFF-8431 v4.1 and SFF-8472 v10.4 specifications. Active direct attach +cables are not supported. -3. Assign an IP address to the interface by entering the following, where - x is the interface number: - ifconfig ethx <IP_address> +Flow Control +------------ +Ethernet Flow Control (IEEE 802.3x) can be configured with ethtool to enable +receiving and transmitting pause frames for ixgbe. When TX is enabled, PAUSE +frames are generated when the receive packet buffer crosses a predefined +threshold. When rx is enabled, the transmit unit will halt for the time delay +specified when a PAUSE frame is received. -4. Verify that the interface works. Enter the following, where <IP_address> - is the IP address for another machine on the same subnet as the interface - that is being tested: +Flow Control is enabled by default. If you want to disable a flow control +capable link partner, use ethtool: - ping <IP_address> + ethtool -A eth? autoneg off RX off TX off +NOTE: For 82598 backplane cards entering 1 gig mode, flow control default +behavior is changed to off. Flow control in 1 gig mode on these devices can +lead to Tx hangs. Additional Configurations ========================= - Viewing Link Messages - --------------------- - Link messages will not be displayed to the console if the distribution is - restricting system messages. In order to see network driver link messages on - your console, set dmesg to eight by entering the following: - - dmesg -n 8 - - NOTE: This setting is not saved across reboots. - - Jumbo Frames ------------ The driver supports Jumbo Frames for all adapters. Jumbo Frames support is @@ -123,13 +142,8 @@ Additional Configurations other protocols besides TCP. It's also safe to use with configurations that are problematic for LRO, namely bridging and iSCSI. - GRO is enabled by default in the driver. Future versions of ethtool will - support disabling and re-enabling GRO on the fly. - - Data Center Bridging, aka DCB ----------------------------- - DCB is a configuration Quality of Service implementation in hardware. It uses the VLAN priority tag (802.1p) to filter traffic. That means that there are 8 different priorities that traffic can be filtered into. @@ -163,24 +177,71 @@ Additional Configurations http://e1000.sf.net - Ethtool ------- The driver utilizes the ethtool interface for driver configuration and - diagnostics, as well as displaying statistical information. Ethtool - version 3.0 or later is required for this functionality. + diagnostics, as well as displaying statistical information. The latest + ethtool version is required for this functionality. The latest release of ethtool can be found from - http://sourceforge.net/projects/gkernel. + http://ftp.kernel.org/pub/software/network/ethtool/ - - NAPI + FCoE ---- + This release of the ixgbe driver contains new code to enable users to use + Fiber Channel over Ethernet (FCoE) and Data Center Bridging (DCB) + functionality that is supported by the 82598-based hardware. This code has + no default effect on the regular driver operation, and configuring DCB and + FCoE is outside the scope of this driver README. Refer to + http://www.open-fcoe.org/ for FCoE project information and contact + e1000-eedc@lists.sourceforge.net for DCB information. + + MAC and VLAN anti-spoofing feature + ---------------------------------- + When a malicious driver attempts to send a spoofed packet, it is dropped by + the hardware and not transmitted. An interrupt is sent to the PF driver + notifying it of the spoof attempt. + + When a spoofed packet is detected the PF driver will send the following + message to the system log (displayed by the "dmesg" command): + + Spoof event(s) detected on VF (n) + + Where n=the VF that attempted to do the spoofing. + + +Performance Tuning +================== + +An excellent article on performance tuning can be found at: + +http://www.redhat.com/promo/summit/2008/downloads/pdf/Thursday/Mark_Wagner.pdf + + +Known Issues +============ + + Enabling SR-IOV in a 32-bit Microsoft* Windows* Server 2008 Guest OS using + Intel (R) 82576-based GbE or Intel (R) 82599-based 10GbE controller under KVM + ----------------------------------------------------------------------------- + KVM Hypervisor/VMM supports direct assignment of a PCIe device to a VM. This + includes traditional PCIe devices, as well as SR-IOV-capable devices using + Intel 82576-based and 82599-based controllers. + + While direct assignment of a PCIe device or an SR-IOV Virtual Function (VF) + to a Linux-based VM running 2.6.32 or later kernel works fine, there is a + known issue with Microsoft Windows Server 2008 VM that results in a "yellow + bang" error. This problem is within the KVM VMM itself, not the Intel driver, + or the SR-IOV logic of the VMM, but rather that KVM emulates an older CPU + model for the guests, and this older CPU model does not support MSI-X + interrupts, which is a requirement for Intel SR-IOV. - NAPI (Rx polling mode) is supported in the ixgbe driver. NAPI is enabled - by default in the driver. + If you wish to use the Intel 82576 or 82599-based controllers in SR-IOV mode + with KVM and a Microsoft Windows Server 2008 guest try the following + workaround. The workaround is to tell KVM to emulate a different model of CPU + when using qemu to create the KVM guest: - See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI. + "-cpu qemu64,model=13" Support diff --git a/Documentation/networking/ixgbevf.txt b/Documentation/networking/ixgbevf.txt index 21dd5d15b6b4..5a91a41fa946 100644 --- a/Documentation/networking/ixgbevf.txt +++ b/Documentation/networking/ixgbevf.txt @@ -35,10 +35,6 @@ Driver ID Guide at: Known Issues/Troubleshooting ============================ - Unloading Physical Function (PF) Driver Causes System Reboots When VM is - Running and VF is Loaded on the VM - ------------------------------------------------------------------------ - Do not unload the PF driver (ixgbe) while VFs are assigned to guests. Support ======= diff --git a/Documentation/networking/phonet.txt b/Documentation/networking/phonet.txt index 24ad2adba6e5..81003581f47a 100644 --- a/Documentation/networking/phonet.txt +++ b/Documentation/networking/phonet.txt @@ -154,9 +154,28 @@ connections, one per accept()'d socket. write(cfd, msg, msglen); } -Connections are established between two endpoints by a "third party" -application. This means that both endpoints are passive; so connect() -is not possible. +Connections are traditionally established between two endpoints by a +"third party" application. This means that both endpoints are passive. + + +As of Linux kernel version 2.6.39, it is also possible to connect +two endpoints directly, using connect() on the active side. This is +intended to support the newer Nokia Wireless Modem API, as found in +e.g. the Nokia Slim Modem in the ST-Ericsson U8500 platform: + + struct sockaddr_spn spn; + int fd; + + fd = socket(PF_PHONET, SOCK_SEQPACKET, PN_PROTO_PIPE); + memset(&spn, 0, sizeof(spn)); + spn.spn_family = AF_PHONET; + spn.spn_obj = ...; + spn.spn_dev = ...; + spn.spn_resource = 0xD9; + connect(fd, (struct sockaddr *)&spn, sizeof(spn)); + /* normal I/O here ... */ + close(fd); + WARNING: When polling a connected pipe socket for writability, there is an @@ -181,45 +200,9 @@ The pipe protocol provides two socket options at the SOL_PNPIPE level: interface index of the network interface created by PNPIPE_ENCAP, or zero if encapsulation is off. - -Phonet Pipe-controller Implementation -------------------------------------- - -Phonet Pipe-controller is enabled by selecting the CONFIG_PHONET_PIPECTRLR Kconfig -option. It is useful when communicating with those Nokia Modems which do not -implement Pipe controller in them e.g. Nokia Slim Modem used in ST-Ericsson -U8500 platform. - -The implementation is based on the Data Connection Establishment Sequence -depicted in 'Nokia Wireless Modem API - Wireless_modem_user_guide.pdf' -document. - -It allows a phonet sequenced socket (host-pep) to initiate a Pipe connection -between itself and a remote pipe-end point (e.g. modem). - -The implementation adds socket options at SOL_PNPIPE level: - - PNPIPE_PIPE_HANDLE - It accepts an integer argument for setting value of pipe handle. - - PNPIPE_ENABLE accepts one integer value (int). If set to zero, the pipe - is disabled. If the value is non-zero, the pipe is enabled. If the pipe - is not (yet) connected, ENOTCONN is error is returned. - -The implementation also adds socket 'connect'. On calling the 'connect', pipe -will be created between the source socket and the destination, and the pipe -state will be set to PIPE_DISABLED. - -After a pipe has been created and enabled successfully, the Pipe data can be -exchanged between the host-pep and remote-pep (modem). - -User-space would typically follow below sequence with Pipe controller:- --socket --bind --setsockopt for PNPIPE_PIPE_HANDLE --connect --setsockopt for PNPIPE_ENCAP_IP --setsockopt for PNPIPE_ENABLE + PNPIPE_HANDLE is a read-only integer value. It contains the underlying + identifier ("pipe handle") of the pipe. This is only defined for + socket descriptors that are already connected or being connected. Authors diff --git a/Documentation/networking/stmmac.txt b/Documentation/networking/stmmac.txt index 7ee770b5ef5f..80a7a3454902 100644 --- a/Documentation/networking/stmmac.txt +++ b/Documentation/networking/stmmac.txt @@ -7,7 +7,7 @@ This is the driver for the MAC 10/100/1000 on-chip Ethernet controllers (Synopsys IP blocks); it has been fully tested on STLinux platforms. Currently this network device driver is for all STM embedded MAC/GMAC -(7xxx SoCs). +(7xxx SoCs). Other platforms start using it i.e. ARM SPEAr. DWC Ether MAC 10/100/1000 Universal version 3.41a and DWC Ether MAC 10/100 Universal version 4.0 have been used for developing the first code @@ -95,9 +95,14 @@ Several information came from the platform; please refer to the driver's Header file in include/linux directory. struct plat_stmmacenet_data { - int bus_id; - int pbl; - int has_gmac; + int bus_id; + int pbl; + int clk_csr; + int has_gmac; + int enh_desc; + int tx_coe; + int bugged_jumbo; + int pmt; void (*fix_mac_speed)(void *priv, unsigned int speed); void (*bus_setup)(unsigned long ioaddr); #ifdef CONFIG_STM_DRIVERS @@ -114,6 +119,12 @@ Where: registers (on STM platforms); - has_gmac: GMAC core is on board (get it at run-time in the next step); - bus_id: bus identifier. +- tx_coe: core is able to perform the tx csum in HW. +- enh_desc: if sets the MAC will use the enhanced descriptor structure. +- clk_csr: CSR Clock range selection. +- bugged_jumbo: some HWs are not able to perform the csum in HW for + over-sized frames due to limited buffer sizes. Setting this + flag the csum will be done in SW on JUMBO frames. struct plat_stmmacphy_data { int bus_id; @@ -131,13 +142,28 @@ Where: - interface: physical MII interface mode; - phy_reset: hook to reset HW function. +SOURCES: +- Kconfig +- Makefile +- stmmac_main.c: main network device driver; +- stmmac_mdio.c: mdio functions; +- stmmac_ethtool.c: ethtool support; +- stmmac_timer.[ch]: timer code used for mitigating the driver dma interrupts + Only tested on ST40 platforms based. +- stmmac.h: private driver structure; +- common.h: common definitions and VFTs; +- descs.h: descriptor structure definitions; +- dwmac1000_core.c: GMAC core functions; +- dwmac1000_dma.c: dma functions for the GMAC chip; +- dwmac1000.h: specific header file for the GMAC; +- dwmac100_core: MAC 100 core and dma code; +- dwmac100_dma.c: dma funtions for the MAC chip; +- dwmac1000.h: specific header file for the MAC; +- dwmac_lib.c: generic DMA functions shared among chips +- enh_desc.c: functions for handling enhanced descriptors +- norm_desc.c: functions for handling normal descriptors + TODO: -- Continue to make the driver more generic and suitable for other Synopsys - Ethernet controllers used on other architectures (i.e. ARM). -- 10G controllers are not supported. -- MAC uses Normal descriptors and GMAC uses enhanced ones. - This is a limit that should be reviewed. MAC could want to - use the enhanced structure. -- Checksumming: Rx/Tx csum is done in HW in case of GMAC only. +- XGMAC controller is not supported. - Review the timer optimisation code to use an embedded device that seems to be available in new chip generations. |