1 files changed, 92 insertions, 0 deletions
diff --git a/arch/ppc/platforms/spd8xx.h b/arch/ppc/platforms/spd8xx.h
new file mode 100644
index 000000000000..ed48d144f415
--- /dev/null
+++ b/arch/ppc/platforms/spd8xx.h
@@ -0,0 +1,92 @@
+/*
+ * Speech Design SPD8xxTS board specific definitions
+ *
+ * Copyright (c) 2000,2001 Wolfgang Denk (wd@denx.de)
+ */
+
+#ifdef __KERNEL__
+#ifndef __ASM_SPD8XX_H__
+#define __ASM_SPD8XX_H__
+
+#include <linux/config.h>
+
+#include <asm/ppcboot.h>
+
+#ifndef __ASSEMBLY__
+#define SPD_IMMR_BASE	0xFFF00000	/* phys. addr of IMMR */
+#define SPD_IMAP_SIZE	(64 * 1024)	/* size of mapped area */
+
+#define IMAP_ADDR	SPD_IMMR_BASE	/* physical base address of IMMR area */
+#define IMAP_SIZE	SPD_IMAP_SIZE	/* mapped size of IMMR area */
+
+#define PCMCIA_MEM_ADDR	((uint)0xFE100000)
+#define PCMCIA_MEM_SIZE	((uint)(64 * 1024))
+
+#define IDE0_INTERRUPT	10		/* = IRQ5 */
+#define IDE1_INTERRUPT	12		/* = IRQ6 */
+#define CPM_INTERRUPT	13		/* = SIU_LEVEL6 (was: SIU_LEVEL2) */
+
+/* override the default number of IDE hardware interfaces */
+#define MAX_HWIFS	2
+
+/*
+ * Definitions for IDE0 Interface
+ */
+#define IDE0_BASE_OFFSET		0x0000	/* Offset in PCMCIA memory */
+#define IDE0_DATA_REG_OFFSET		0x0000
+#define IDE0_ERROR_REG_OFFSET		0x0081
+#define IDE0_NSECTOR_REG_OFFSET		0x0082
+#define IDE0_SECTOR_REG_OFFSET		0x0083
+#define IDE0_LCYL_REG_OFFSET		0x0084
+#define IDE0_HCYL_REG_OFFSET		0x0085
+#define IDE0_SELECT_REG_OFFSET		0x0086
+#define IDE0_STATUS_REG_OFFSET		0x0087
+#define IDE0_CONTROL_REG_OFFSET		0x0106
+#define IDE0_IRQ_REG_OFFSET		0x000A	/* not used */
+
+/*
+ * Definitions for IDE1 Interface
+ */
+#define IDE1_BASE_OFFSET		0x0C00	/* Offset in PCMCIA memory */
+#define IDE1_DATA_REG_OFFSET		0x0000
+#define IDE1_ERROR_REG_OFFSET		0x0081
+#define IDE1_NSECTOR_REG_OFFSET		0x0082
+#define IDE1_SECTOR_REG_OFFSET		0x0083
+#define IDE1_LCYL_REG_OFFSET		0x0084
+#define IDE1_HCYL_REG_OFFSET		0x0085
+#define IDE1_SELECT_REG_OFFSET		0x0086
+#define IDE1_STATUS_REG_OFFSET		0x0087
+#define IDE1_CONTROL_REG_OFFSET		0x0106
+#define IDE1_IRQ_REG_OFFSET		0x000A	/* not used */
+
+/* CPM Ethernet through SCCx.
+ *
+ * Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC2 use.
+ */
+#define PA_ENET_MDC	((ushort)0x0001)	/* PA 15 !!! */
+#define PA_ENET_MDIO	((ushort)0x0002)	/* PA 14 !!! */
+#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
+#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
+#define PA_ENET_RCLK	((ushort)0x0200)	/* PA  6 */
+#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
+
+#define PB_ENET_TENA	((uint)0x00002000)	/* PB 18 */
+
+#define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
+#define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
+#define PC_ENET_RESET	((ushort)0x0100)	/* PC  7 !!! */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
+ * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x0000ff00)
+#define SICR_ENET_CLKRT	((uint)0x00002E00)
+
+/* We don't use the 8259.
+*/
+#define NR_8259_INTS	0
+
+#endif /* !__ASSEMBLY__ */
+#endif /* __ASM_SPD8XX_H__ */
+#endif /* __KERNEL__ */