diff options
Diffstat (limited to 'drivers/bluetooth')
| -rw-r--r-- | drivers/bluetooth/btsdio.c | 9 | ||||
| -rw-r--r-- | drivers/bluetooth/btusb.c | 24 |
2 files changed, 15 insertions, 18 deletions
diff --git a/drivers/bluetooth/btsdio.c b/drivers/bluetooth/btsdio.c index 7b624423a7e8..89ccb604045c 100644 --- a/drivers/bluetooth/btsdio.c +++ b/drivers/bluetooth/btsdio.c @@ -31,6 +31,7 @@ #include <linux/errno.h> #include <linux/skbuff.h> +#include <linux/mmc/host.h> #include <linux/mmc/sdio_ids.h> #include <linux/mmc/sdio_func.h> @@ -291,6 +292,14 @@ static int btsdio_probe(struct sdio_func *func, tuple = tuple->next; } + /* BCM43341 devices soldered onto the PCB (non-removable) use an + * uart connection for bluetooth, ignore the BT SDIO interface. + */ + if (func->vendor == SDIO_VENDOR_ID_BROADCOM && + func->device == SDIO_DEVICE_ID_BROADCOM_43341 && + !mmc_card_is_removable(func->card->host)) + return -ENODEV; + data = devm_kzalloc(&func->dev, sizeof(*data), GFP_KERNEL); if (!data) return -ENOMEM; diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index ce120fbe229e..54cef3dc0beb 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -23,6 +23,7 @@ #include <linux/module.h> #include <linux/usb.h> +#include <linux/usb/quirks.h> #include <linux/firmware.h> #include <asm/unaligned.h> @@ -360,8 +361,8 @@ static const struct usb_device_id blacklist_table[] = { #define BTUSB_FIRMWARE_LOADED 7 #define BTUSB_FIRMWARE_FAILED 8 #define BTUSB_BOOTING 9 -#define BTUSB_RESET_RESUME 10 -#define BTUSB_DIAG_RUNNING 11 +#define BTUSB_DIAG_RUNNING 10 +#define BTUSB_OOB_WAKE_ENABLED 11 struct btusb_data { struct hci_dev *hdev; @@ -1050,10 +1051,6 @@ static int btusb_open(struct hci_dev *hdev) return err; data->intf->needs_remote_wakeup = 1; - /* device specific wakeup source enabled and required for USB - * remote wakeup while host is suspended - */ - device_wakeup_enable(&data->udev->dev); if (test_and_set_bit(BTUSB_INTR_RUNNING, &data->flags)) goto done; @@ -1117,7 +1114,6 @@ static int btusb_close(struct hci_dev *hdev) goto failed; data->intf->needs_remote_wakeup = 0; - device_wakeup_disable(&data->udev->dev); usb_autopm_put_interface(data->intf); failed: @@ -2977,9 +2973,9 @@ static int btusb_probe(struct usb_interface *intf, /* QCA Rome devices lose their updated firmware over suspend, * but the USB hub doesn't notice any status change. - * Explicitly request a device reset on resume. + * explicitly request a device reset on resume. */ - set_bit(BTUSB_RESET_RESUME, &data->flags); + interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME; } #ifdef CONFIG_BT_HCIBTUSB_RTL @@ -2990,7 +2986,7 @@ static int btusb_probe(struct usb_interface *intf, * but the USB hub doesn't notice any status change. * Explicitly request a device reset on resume. */ - set_bit(BTUSB_RESET_RESUME, &data->flags); + interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME; } #endif @@ -3147,14 +3143,6 @@ static int btusb_suspend(struct usb_interface *intf, pm_message_t message) btusb_stop_traffic(data); usb_kill_anchored_urbs(&data->tx_anchor); - /* Optionally request a device reset on resume, but only when - * wakeups are disabled. If wakeups are enabled we assume the - * device will stay powered up throughout suspend. - */ - if (test_bit(BTUSB_RESET_RESUME, &data->flags) && - !device_may_wakeup(&data->udev->dev)) - data->udev->reset_resume = 1; - return 0; } |