diff options
Diffstat (limited to 'drivers/infiniband/hw/qib/qib_sd7220.c')
| -rw-r--r-- | drivers/infiniband/hw/qib/qib_sd7220.c | 1447 |
1 files changed, 1447 insertions, 0 deletions
diff --git a/drivers/infiniband/hw/qib/qib_sd7220.c b/drivers/infiniband/hw/qib/qib_sd7220.c new file mode 100644 index 000000000000..e9f9f8bc3204 --- /dev/null +++ b/drivers/infiniband/hw/qib/qib_sd7220.c @@ -0,0 +1,1447 @@ +/* + * Copyright (c) 2006, 2007, 2008, 2009, 2010 QLogic Corporation. + * All rights reserved. + * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. + * + * This software is available to you under a choice of one of two + * licenses. You may choose to be licensed under the terms of the GNU + * General Public License (GPL) Version 2, available from the file + * COPYING in the main directory of this source tree, or the + * OpenIB.org BSD license below: + * + * Redistribution and use in source and binary forms, with or + * without modification, are permitted provided that the following + * conditions are met: + * + * - Redistributions of source code must retain the above + * copyright notice, this list of conditions and the following + * disclaimer. + * + * - Redistributions in binary form must reproduce the above + * copyright notice, this list of conditions and the following + * disclaimer in the documentation and/or other materials + * provided with the distribution. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS + * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN + * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE + * SOFTWARE. + */ +/* + * This file contains all of the code that is specific to the SerDes + * on the QLogic_IB 7220 chip. + */ + +#include <linux/pci.h> +#include <linux/delay.h> +#include <linux/firmware.h> + +#include "qib.h" +#include "qib_7220.h" + +#define SD7220_FW_NAME "qlogic/sd7220.fw" +MODULE_FIRMWARE(SD7220_FW_NAME); + +/* + * Same as in qib_iba7220.c, but just the registers needed here. + * Could move whole set to qib_7220.h, but decided better to keep + * local. + */ +#define KREG_IDX(regname) (QIB_7220_##regname##_OFFS / sizeof(u64)) +#define kr_hwerrclear KREG_IDX(HwErrClear) +#define kr_hwerrmask KREG_IDX(HwErrMask) +#define kr_hwerrstatus KREG_IDX(HwErrStatus) +#define kr_ibcstatus KREG_IDX(IBCStatus) +#define kr_ibserdesctrl KREG_IDX(IBSerDesCtrl) +#define kr_scratch KREG_IDX(Scratch) +#define kr_xgxs_cfg KREG_IDX(XGXSCfg) +/* these are used only here, not in qib_iba7220.c */ +#define kr_ibsd_epb_access_ctrl KREG_IDX(ibsd_epb_access_ctrl) +#define kr_ibsd_epb_transaction_reg KREG_IDX(ibsd_epb_transaction_reg) +#define kr_pciesd_epb_transaction_reg KREG_IDX(pciesd_epb_transaction_reg) +#define kr_pciesd_epb_access_ctrl KREG_IDX(pciesd_epb_access_ctrl) +#define kr_serdes_ddsrxeq0 KREG_IDX(SerDes_DDSRXEQ0) + +/* + * The IBSerDesMappTable is a memory that holds values to be stored in + * various SerDes registers by IBC. + */ +#define kr_serdes_maptable KREG_IDX(IBSerDesMappTable) + +/* + * Below used for sdnum parameter, selecting one of the two sections + * used for PCIe, or the single SerDes used for IB. + */ +#define PCIE_SERDES0 0 +#define PCIE_SERDES1 1 + +/* + * The EPB requires addressing in a particular form. EPB_LOC() is intended + * to make #definitions a little more readable. + */ +#define EPB_ADDR_SHF 8 +#define EPB_LOC(chn, elt, reg) \ + (((elt & 0xf) | ((chn & 7) << 4) | ((reg & 0x3f) << 9)) << \ + EPB_ADDR_SHF) +#define EPB_IB_QUAD0_CS_SHF (25) +#define EPB_IB_QUAD0_CS (1U << EPB_IB_QUAD0_CS_SHF) +#define EPB_IB_UC_CS_SHF (26) +#define EPB_PCIE_UC_CS_SHF (27) +#define EPB_GLOBAL_WR (1U << (EPB_ADDR_SHF + 8)) + +/* Forward declarations. */ +static int qib_sd7220_reg_mod(struct qib_devdata *dd, int sdnum, u32 loc, + u32 data, u32 mask); +static int ibsd_mod_allchnls(struct qib_devdata *dd, int loc, int val, + int mask); +static int qib_sd_trimdone_poll(struct qib_devdata *dd); +static void qib_sd_trimdone_monitor(struct qib_devdata *dd, const char *where); +static int qib_sd_setvals(struct qib_devdata *dd); +static int qib_sd_early(struct qib_devdata *dd); +static int qib_sd_dactrim(struct qib_devdata *dd); +static int qib_internal_presets(struct qib_devdata *dd); +/* Tweak the register (CMUCTRL5) that contains the TRIMSELF controls */ +static int qib_sd_trimself(struct qib_devdata *dd, int val); +static int epb_access(struct qib_devdata *dd, int sdnum, int claim); +static int qib_sd7220_ib_load(struct qib_devdata *dd, + const struct firmware *fw); +static int qib_sd7220_ib_vfy(struct qib_devdata *dd, + const struct firmware *fw); + +/* + * Below keeps track of whether the "once per power-on" initialization has + * been done, because uC code Version 1.32.17 or higher allows the uC to + * be reset at will, and Automatic Equalization may require it. So the + * state of the reset "pin", is no longer valid. Instead, we check for the + * actual uC code having been loaded. + */ +static int qib_ibsd_ucode_loaded(struct qib_pportdata *ppd, + const struct firmware *fw) +{ + struct qib_devdata *dd = ppd->dd; + + if (!dd->cspec->serdes_first_init_done && + qib_sd7220_ib_vfy(dd, fw) > 0) + dd->cspec->serdes_first_init_done = 1; + return dd->cspec->serdes_first_init_done; +} + +/* repeat #define for local use. "Real" #define is in qib_iba7220.c */ +#define QLOGIC_IB_HWE_IB_UC_MEMORYPARITYERR 0x0000004000000000ULL +#define IB_MPREG5 (EPB_LOC(6, 0, 0xE) | (1L << EPB_IB_UC_CS_SHF)) +#define IB_MPREG6 (EPB_LOC(6, 0, 0xF) | (1U << EPB_IB_UC_CS_SHF)) +#define UC_PAR_CLR_D 8 +#define UC_PAR_CLR_M 0xC +#define IB_CTRL2(chn) (EPB_LOC(chn, 7, 3) | EPB_IB_QUAD0_CS) +#define START_EQ1(chan) EPB_LOC(chan, 7, 0x27) + +void qib_sd7220_clr_ibpar(struct qib_devdata *dd) +{ + int ret; + + /* clear, then re-enable parity errs */ + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, IB_MPREG6, + UC_PAR_CLR_D, UC_PAR_CLR_M); + if (ret < 0) { + qib_dev_err(dd, "Failed clearing IBSerDes Parity err\n"); + goto bail; + } + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, IB_MPREG6, 0, + UC_PAR_CLR_M); + + qib_read_kreg32(dd, kr_scratch); + udelay(4); + qib_write_kreg(dd, kr_hwerrclear, + QLOGIC_IB_HWE_IB_UC_MEMORYPARITYERR); + qib_read_kreg32(dd, kr_scratch); +bail: + return; +} + +/* + * After a reset or other unusual event, the epb interface may need + * to be re-synchronized, between the host and the uC. + * returns <0 for failure to resync within IBSD_RESYNC_TRIES (not expected) + */ +#define IBSD_RESYNC_TRIES 3 +#define IB_PGUDP(chn) (EPB_LOC((chn), 2, 1) | EPB_IB_QUAD0_CS) +#define IB_CMUDONE(chn) (EPB_LOC((chn), 7, 0xF) | EPB_IB_QUAD0_CS) + +static int qib_resync_ibepb(struct qib_devdata *dd) +{ + int ret, pat, tries, chn; + u32 loc; + + ret = -1; + chn = 0; + for (tries = 0; tries < (4 * IBSD_RESYNC_TRIES); ++tries) { + loc = IB_PGUDP(chn); + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, loc, 0, 0); + if (ret < 0) { + qib_dev_err(dd, "Failed read in resync\n"); + continue; + } + if (ret != 0xF0 && ret != 0x55 && tries == 0) + qib_dev_err(dd, "unexpected pattern in resync\n"); + pat = ret ^ 0xA5; /* alternate F0 and 55 */ + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, loc, pat, 0xFF); + if (ret < 0) { + qib_dev_err(dd, "Failed write in resync\n"); + continue; + } + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, loc, 0, 0); + if (ret < 0) { + qib_dev_err(dd, "Failed re-read in resync\n"); + continue; + } + if (ret != pat) { + qib_dev_err(dd, "Failed compare1 in resync\n"); + continue; + } + loc = IB_CMUDONE(chn); + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, loc, 0, 0); + if (ret < 0) { + qib_dev_err(dd, "Failed CMUDONE rd in resync\n"); + continue; + } + if ((ret & 0x70) != ((chn << 4) | 0x40)) { + qib_dev_err(dd, "Bad CMUDONE value %02X, chn %d\n", + ret, chn); + continue; + } + if (++chn == 4) + break; /* Success */ + } + return (ret > 0) ? 0 : ret; +} + +/* + * Localize the stuff that should be done to change IB uC reset + * returns <0 for errors. + */ +static int qib_ibsd_reset(struct qib_devdata *dd, int assert_rst) +{ + u64 rst_val; + int ret = 0; + unsigned long flags; + + rst_val = qib_read_kreg64(dd, kr_ibserdesctrl); + if (assert_rst) { + /* + * Vendor recommends "interrupting" uC before reset, to + * minimize possible glitches. + */ + spin_lock_irqsave(&dd->cspec->sdepb_lock, flags); + epb_access(dd, IB_7220_SERDES, 1); + rst_val |= 1ULL; + /* Squelch possible parity error from _asserting_ reset */ + qib_write_kreg(dd, kr_hwerrmask, + dd->cspec->hwerrmask & + ~QLOGIC_IB_HWE_IB_UC_MEMORYPARITYERR); + qib_write_kreg(dd, kr_ibserdesctrl, rst_val); + /* flush write, delay to ensure it took effect */ + qib_read_kreg32(dd, kr_scratch); + udelay(2); + /* once it's reset, can remove interrupt */ + epb_access(dd, IB_7220_SERDES, -1); + spin_unlock_irqrestore(&dd->cspec->sdepb_lock, flags); + } else { + /* + * Before we de-assert reset, we need to deal with + * possible glitch on the Parity-error line. + * Suppress it around the reset, both in chip-level + * hwerrmask and in IB uC control reg. uC will allow + * it again during startup. + */ + u64 val; + rst_val &= ~(1ULL); + qib_write_kreg(dd, kr_hwerrmask, + dd->cspec->hwerrmask & + ~QLOGIC_IB_HWE_IB_UC_MEMORYPARITYERR); + + ret = qib_resync_ibepb(dd); + if (ret < 0) + qib_dev_err(dd, "unable to re-sync IB EPB\n"); + + /* set uC control regs to suppress parity errs */ + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, IB_MPREG5, 1, 1); + if (ret < 0) + goto bail; + /* IB uC code past Version 1.32.17 allow suppression of wdog */ + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, IB_MPREG6, 0x80, + 0x80); + if (ret < 0) { + qib_dev_err(dd, "Failed to set WDOG disable\n"); + goto bail; + } + qib_write_kreg(dd, kr_ibserdesctrl, rst_val); + /* flush write, delay for startup */ + qib_read_kreg32(dd, kr_scratch); + udelay(1); + /* clear, then re-enable parity errs */ + qib_sd7220_clr_ibpar(dd); + val = qib_read_kreg64(dd, kr_hwerrstatus); + if (val & QLOGIC_IB_HWE_IB_UC_MEMORYPARITYERR) { + qib_dev_err(dd, "IBUC Parity still set after RST\n"); + dd->cspec->hwerrmask &= + ~QLOGIC_IB_HWE_IB_UC_MEMORYPARITYERR; + } + qib_write_kreg(dd, kr_hwerrmask, + dd->cspec->hwerrmask); + } + +bail: + return ret; +} + +static void qib_sd_trimdone_monitor(struct qib_devdata *dd, + const char *where) +{ + int ret, chn, baduns; + u64 val; + + if (!where) + where = "?"; + + /* give time for reset to settle out in EPB */ + udelay(2); + + ret = qib_resync_ibepb(dd); + if (ret < 0) + qib_dev_err(dd, "not able to re-sync IB EPB (%s)\n", where); + + /* Do "sacrificial read" to get EPB in sane state after reset */ + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, IB_CTRL2(0), 0, 0); + if (ret < 0) + qib_dev_err(dd, "Failed TRIMDONE 1st read, (%s)\n", where); + + /* Check/show "summary" Trim-done bit in IBCStatus */ + val = qib_read_kreg64(dd, kr_ibcstatus); + if (!(val & (1ULL << 11))) + qib_dev_err(dd, "IBCS TRIMDONE clear (%s)\n", where); + /* + * Do "dummy read/mod/wr" to get EPB in sane state after reset + * The default value for MPREG6 is 0. + */ + udelay(2); + + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, IB_MPREG6, 0x80, 0x80); + if (ret < 0) + qib_dev_err(dd, "Failed Dummy RMW, (%s)\n", where); + udelay(10); + + baduns = 0; + + for (chn = 3; chn >= 0; --chn) { + /* Read CTRL reg for each channel to check TRIMDONE */ + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, + IB_CTRL2(chn), 0, 0); + if (ret < 0) + qib_dev_err(dd, "Failed checking TRIMDONE, chn %d" + " (%s)\n", chn, where); + + if (!(ret & 0x10)) { + int probe; + + baduns |= (1 << chn); + qib_dev_err(dd, "TRIMDONE cleared on chn %d (%02X)." + " (%s)\n", chn, ret, where); + probe = qib_sd7220_reg_mod(dd, IB_7220_SERDES, + IB_PGUDP(0), 0, 0); + qib_dev_err(dd, "probe is %d (%02X)\n", + probe, probe); + probe = qib_sd7220_reg_mod(dd, IB_7220_SERDES, + IB_CTRL2(chn), 0, 0); + qib_dev_err(dd, "re-read: %d (%02X)\n", + probe, probe); + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, + IB_CTRL2(chn), 0x10, 0x10); + if (ret < 0) + qib_dev_err(dd, + "Err on TRIMDONE rewrite1\n"); + } + } + for (chn = 3; chn >= 0; --chn) { + /* Read CTRL reg for each channel to check TRIMDONE */ + if (baduns & (1 << chn)) { + qib_dev_err(dd, + "Reseting TRIMDONE on chn %d (%s)\n", + chn, where); + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, + IB_CTRL2(chn), 0x10, 0x10); + if (ret < 0) + qib_dev_err(dd, "Failed re-setting " + "TRIMDONE, chn %d (%s)\n", + chn, where); + } + } +} + +/* + * Below is portion of IBA7220-specific bringup_serdes() that actually + * deals with registers and memory within the SerDes itself. + * Post IB uC code version 1.32.17, was_reset being 1 is not really + * informative, so we double-check. + */ +int qib_sd7220_init(struct qib_devdata *dd) +{ + const struct firmware *fw; + int ret = 1; /* default to failure */ + int first_reset, was_reset; + + /* SERDES MPU reset recorded in D0 */ + was_reset = (qib_read_kreg64(dd, kr_ibserdesctrl) & 1); + if (!was_reset) { + /* entered with reset not asserted, we need to do it */ + qib_ibsd_reset(dd, 1); + qib_sd_trimdone_monitor(dd, "Driver-reload"); + } + + ret = request_firmware(&fw, SD7220_FW_NAME, &dd->pcidev->dev); + if (ret) { + qib_dev_err(dd, "Failed to load IB SERDES image\n"); + goto done; + } + + /* Substitute our deduced value for was_reset */ + ret = qib_ibsd_ucode_loaded(dd->pport, fw); + if (ret < 0) + goto bail; + + first_reset = !ret; /* First reset if IBSD uCode not yet loaded */ + /* + * Alter some regs per vendor latest doc, reset-defaults + * are not right for IB. + */ + ret = qib_sd_early(dd); + if (ret < 0) { + qib_dev_err(dd, "Failed to set IB SERDES early defaults\n"); + goto bail; + } + /* + * Set DAC manual trim IB. + * We only do this once after chip has been reset (usually + * same as once per system boot). + */ + if (first_reset) { + ret = qib_sd_dactrim(dd); + if (ret < 0) { + qib_dev_err(dd, "Failed IB SERDES DAC trim\n"); + goto bail; + } + } + /* + * Set various registers (DDS and RXEQ) that will be + * controlled by IBC (in 1.2 mode) to reasonable preset values + * Calling the "internal" version avoids the "check for needed" + * and "trimdone monitor" that might be counter-productive. + */ + ret = qib_internal_presets(dd); + if (ret < 0) { + qib_dev_err(dd, "Failed to set IB SERDES presets\n"); + goto bail; + } + ret = qib_sd_trimself(dd, 0x80); + if (ret < 0) { + qib_dev_err(dd, "Failed to set IB SERDES TRIMSELF\n"); + goto bail; + } + + /* Load image, then try to verify */ + ret = 0; /* Assume success */ + if (first_reset) { + int vfy; + int trim_done; + + ret = qib_sd7220_ib_load(dd, fw); + if (ret < 0) { + qib_dev_err(dd, "Failed to load IB SERDES image\n"); + goto bail; + } else { + /* Loaded image, try to verify */ + vfy = qib_sd7220_ib_vfy(dd, fw); + if (vfy != ret) { + qib_dev_err(dd, "SERDES PRAM VFY failed\n"); + goto bail; + } /* end if verified */ + } /* end if loaded */ + + /* + * Loaded and verified. Almost good... + * hold "success" in ret + */ + ret = 0; + /* + * Prev steps all worked, continue bringup + * De-assert RESET to uC, only in first reset, to allow + * trimming. + * + * Since our default setup sets START_EQ1 to + * PRESET, we need to clear that for this very first run. + */ + ret = ibsd_mod_allchnls(dd, START_EQ1(0), 0, 0x38); + if (ret < 0) { + qib_dev_err(dd, "Failed clearing START_EQ1\n"); + goto bail; + } + + qib_ibsd_reset(dd, 0); + /* + * If this is not the first reset, trimdone should be set + * already. We may need to check about this. + */ + trim_done = qib_sd_trimdone_poll(dd); + /* + * Whether or not trimdone succeeded, we need to put the + * uC back into reset to avoid a possible fight with the + * IBC state-machine. + */ + qib_ibsd_reset(dd, 1); + + if (!trim_done) { + qib_dev_err(dd, "No TRIMDONE seen\n"); + goto bail; + } + /* + * DEBUG: check each time we reset if trimdone bits have + * gotten cleared, and re-set them. + */ + qib_sd_trimdone_monitor(dd, "First-reset"); + /* Remember so we do not re-do the load, dactrim, etc. */ + dd->cspec->serdes_first_init_done = 1; + } + /* + * setup for channel training and load values for + * RxEq and DDS in tables used by IBC in IB1.2 mode + */ + ret = 0; + if (qib_sd_setvals(dd) >= 0) + goto done; +bail: + ret = 1; +done: + /* start relock timer regardless, but start at 1 second */ + set_7220_relock_poll(dd, -1); + + release_firmware(fw); + return ret; +} + +#define EPB_ACC_REQ 1 +#define EPB_ACC_GNT 0x100 +#define EPB_DATA_MASK 0xFF +#define EPB_RD (1ULL << 24) +#define EPB_TRANS_RDY (1ULL << 31) +#define EPB_TRANS_ERR (1ULL << 30) +#define EPB_TRANS_TRIES 5 + +/* + * query, claim, release ownership of the EPB (External Parallel Bus) + * for a specified SERDES. + * the "claim" parameter is >0 to claim, <0 to release, 0 to query. + * Returns <0 for errors, >0 if we had ownership, else 0. + */ +static int epb_access(struct qib_devdata *dd, int sdnum, int claim) +{ + u16 acc; + u64 accval; + int owned = 0; + u64 oct_sel = 0; + + switch (sdnum) { + case IB_7220_SERDES: + /* + * The IB SERDES "ownership" is fairly simple. A single each + * request/grant. + */ + acc = kr_ibsd_epb_access_ctrl; + break; + + case PCIE_SERDES0: + case PCIE_SERDES1: + /* PCIe SERDES has two "octants", need to select which */ + acc = kr_pciesd_epb_access_ctrl; + oct_sel = (2 << (sdnum - PCIE_SERDES0)); + break; + + default: + return 0; + } + + /* Make sure any outstanding transaction was seen */ + qib_read_kreg32(dd, kr_scratch); + udelay(15); + + accval = qib_read_kreg32(dd, acc); + + owned = !!(accval & EPB_ACC_GNT); + if (claim < 0) { + /* Need to release */ + u64 pollval; + /* + * The only writeable bits are the request and CS. + * Both should be clear + */ + u64 newval = 0; + qib_write_kreg(dd, acc, newval); + /* First read after write is not trustworthy */ + pollval = qib_read_kreg32(dd, acc); + udelay(5); + pollval = qib_read_kreg32(dd, acc); + if (pollval & EPB_ACC_GNT) + owned = -1; + } else if (claim > 0) { + /* Need to claim */ + u64 pollval; + u64 newval = EPB_ACC_REQ | oct_sel; + qib_write_kreg(dd, acc, newval); + /* First read after write is not trustworthy */ + pollval = qib_read_kreg32(dd, acc); + udelay(5); + pollval = qib_read_kreg32(dd, acc); + if (!(pollval & EPB_ACC_GNT)) + owned = -1; + } + return owned; +} + +/* + * Lemma to deal with race condition of write..read to epb regs + */ +static int epb_trans(struct qib_devdata *dd, u16 reg, u64 i_val, u64 *o_vp) +{ + int tries; + u64 transval; + + qib_write_kreg(dd, reg, i_val); + /* Throw away first read, as RDY bit may be stale */ + transval = qib_read_kreg64(dd, reg); + + for (tries = EPB_TRANS_TRIES; tries; --tries) { + transval = qib_read_kreg32(dd, reg); + if (transval & EPB_TRANS_RDY) + break; + udelay(5); + } + if (transval & EPB_TRANS_ERR) + return -1; + if (tries > 0 && o_vp) + *o_vp = transval; + return tries; +} + +/** + * qib_sd7220_reg_mod - modify SERDES register + * @dd: the qlogic_ib device + * @sdnum: which SERDES to access + * @loc: location - channel, element, register, as packed by EPB_LOC() macro. + * @wd: Write Data - value to set in register + * @mask: ones where data should be spliced into reg. + * + * Basic register read/modify/write, with un-needed acesses elided. That is, + * a mask of zero will prevent write, while a mask of 0xFF will prevent read. + * returns current (presumed, if a write was done) contents of selected + * register, or <0 if errors. + */ +static int qib_sd7220_reg_mod(struct qib_devdata *dd, int sdnum, u32 loc, + u32 wd, u32 mask) +{ + u16 trans; + u64 transval; + int owned; + int tries, ret; + unsigned long flags; + + switch (sdnum) { + case IB_7220_SERDES: + trans = kr_ibsd_epb_transaction_reg; + break; + + case PCIE_SERDES0: + case PCIE_SERDES1: + trans = kr_pciesd_epb_transaction_reg; + break; + + default: + return -1; + } + + /* + * All access is locked in software (vs other host threads) and + * hardware (vs uC access). + */ + spin_lock_irqsave(&dd->cspec->sdepb_lock, flags); + + owned = epb_access(dd, sdnum, 1); + if (owned < 0) { + spin_unlock_irqrestore(&dd->cspec->sdepb_lock, flags); + return -1; + } + ret = 0; + for (tries = EPB_TRANS_TRIES; tries; --tries) { + transval = qib_read_kreg32(dd, trans); + if (transval & EPB_TRANS_RDY) + break; + udelay(5); + } + + if (tries > 0) { + tries = 1; /* to make read-skip work */ + if (mask != 0xFF) { + /* + * Not a pure write, so need to read. + * loc encodes chip-select as well as address + */ + transval = loc | EPB_RD; + tries = epb_trans(dd, trans, transval, &transval); + } + if (tries > 0 && mask != 0) { + /* + * Not a pure read, so need to write. + */ + wd = (wd & mask) | (transval & ~mask); + transval = loc | (wd & EPB_DATA_MASK); + tries = epb_trans(dd, trans, transval, &transval); + } + } + /* else, failed to see ready, what error-handling? */ + + /* + * Release bus. Failure is an error. + */ + if (epb_access(dd, sdnum, -1) < 0) + ret = -1; + else + ret = transval & EPB_DATA_MASK; + + spin_unlock_irqrestore(&dd->cspec->sdepb_lock, flags); + if (tries <= 0) + ret = -1; + return ret; +} + +#define EPB_ROM_R (2) +#define EPB_ROM_W (1) +/* + * Below, all uC-related, use appropriate UC_CS, depending + * on which SerDes is used. + */ +#define EPB_UC_CTL EPB_LOC(6, 0, 0) +#define EPB_MADDRL EPB_LOC(6, 0, 2) +#define EPB_MADDRH EPB_LOC(6, 0, 3) +#define EPB_ROMDATA EPB_LOC(6, 0, 4) +#define EPB_RAMDATA EPB_LOC(6, 0, 5) + +/* Transfer date to/from uC Program RAM of IB or PCIe SerDes */ +static int qib_sd7220_ram_xfer(struct qib_devdata *dd, int sdnum, u32 loc, + u8 *buf, int cnt, int rd_notwr) +{ + u16 trans; + u64 transval; + u64 csbit; + int owned; + int tries; + int sofar; + int addr; + int ret; + unsigned long flags; + const char *op; + + /* Pick appropriate transaction reg and "Chip select" for this serdes */ + switch (sdnum) { + case IB_7220_SERDES: + csbit = 1ULL << EPB_IB_UC_CS_SHF; + trans = kr_ibsd_epb_transaction_reg; + break; + + case PCIE_SERDES0: + case PCIE_SERDES1: + /* PCIe SERDES has uC "chip select" in different bit, too */ + csbit = 1ULL << EPB_PCIE_UC_CS_SHF; + trans = kr_pciesd_epb_transaction_reg; + break; + + default: + return -1; + } + + op = rd_notwr ? "Rd" : "Wr"; + spin_lock_irqsave(&dd->cspec->sdepb_lock, flags); + + owned = epb_access(dd, sdnum, 1); + if (owned < 0) { + spin_unlock_irqrestore(&dd->cspec->sdepb_lock, flags); + return -1; + } + + /* + * In future code, we may need to distinguish several address ranges, + * and select various memories based on this. For now, just trim + * "loc" (location including address and memory select) to + * "addr" (address within memory). we will only support PRAM + * The memory is 8KB. + */ + addr = loc & 0x1FFF; + for (tries = EPB_TRANS_TRIES; tries; --tries) { + transval = qib_read_kreg32(dd, trans); + if (transval & EPB_TRANS_RDY) + break; + udelay(5); + } + + sofar = 0; + if (tries > 0) { + /* + * Every "memory" access is doubly-indirect. + * We set two bytes of address, then read/write + * one or mores bytes of data. + */ + + /* First, we set control to "Read" or "Write" */ + transval = csbit | EPB_UC_CTL | + (rd_notwr ? EPB_ROM_R : EPB_ROM_W); + tries = epb_trans(dd, trans, transval, &transval); + while (tries > 0 && sofar < cnt) { + if (!sofar) { + /* Only set address at start of chunk */ + int addrbyte = (addr + sofar) >> 8; + transval = csbit | EPB_MADDRH | addrbyte; + tries = epb_trans(dd, trans, transval, + &transval); + if (tries <= 0) + break; + addrbyte = (addr + sofar) & 0xFF; + transval = csbit | EPB_MADDRL | addrbyte; + tries = epb_trans(dd, trans, transval, + &transval); + if (tries <= 0) + break; + } + + if (rd_notwr) + transval = csbit | EPB_ROMDATA | EPB_RD; + else + transval = csbit | EPB_ROMDATA | buf[sofar]; + tries = epb_trans(dd, trans, transval, &transval); + if (tries <= 0) + break; + if (rd_notwr) + buf[sofar] = transval & EPB_DATA_MASK; + ++sofar; + } + /* Finally, clear control-bit for Read or Write */ + transval = csbit | EPB_UC_CTL; + tries = epb_trans(dd, trans, transval, &transval); + } + + ret = sofar; + /* Release bus. Failure is an error */ + if (epb_access(dd, sdnum, -1) < 0) + ret = -1; + + spin_unlock_irqrestore(&dd->cspec->sdepb_lock, flags); + if (tries <= 0) + ret = -1; + return ret; +} + +#define PROG_CHUNK 64 + +static int qib_sd7220_prog_ld(struct qib_devdata *dd, int sdnum, + const u8 *img, int len, int offset) +{ + int cnt, sofar, req; + + sofar = 0; + while (sofar < len) { + req = len - sofar; + if (req > PROG_CHUNK) + req = PROG_CHUNK; + cnt = qib_sd7220_ram_xfer(dd, sdnum, offset + sofar, + (u8 *)img + sofar, req, 0); + if (cnt < req) { + sofar = -1; + break; + } + sofar += req; + } + return sofar; +} + +#define VFY_CHUNK 64 +#define SD_PRAM_ERROR_LIMIT 42 + +static int qib_sd7220_prog_vfy(struct qib_devdata *dd, int sdnum, + const u8 *img, int len, int offset) +{ + int cnt, sofar, req, idx, errors; + unsigned char readback[VFY_CHUNK]; + + errors = 0; + sofar = 0; + while (sofar < len) { + req = len - sofar; + if (req > VFY_CHUNK) + req = VFY_CHUNK; + cnt = qib_sd7220_ram_xfer(dd, sdnum, sofar + offset, + readback, req, 1); + if (cnt < req) { + /* failed in read itself */ + sofar = -1; + break; + } + for (idx = 0; idx < cnt; ++idx) { + if (readback[idx] != img[idx+sofar]) + ++errors; + } + sofar += cnt; + } + return errors ? -errors : sofar; +} + +static int +qib_sd7220_ib_load(struct qib_devdata *dd, const struct firmware *fw) +{ + return qib_sd7220_prog_ld(dd, IB_7220_SERDES, fw->data, fw->size, 0); +} + +static int +qib_sd7220_ib_vfy(struct qib_devdata *dd, const struct firmware *fw) +{ + return qib_sd7220_prog_vfy(dd, IB_7220_SERDES, fw->data, fw->size, 0); +} + +/* + * IRQ not set up at this point in init, so we poll. + */ +#define IB_SERDES_TRIM_DONE (1ULL << 11) +#define TRIM_TMO (30) + +static int qib_sd_trimdone_poll(struct qib_devdata *dd) +{ + int trim_tmo, ret; + uint64_t val; + + /* + * Default to failure, so IBC will not start + * without IB_SERDES_TRIM_DONE. + */ + ret = 0; + for (trim_tmo = 0; trim_tmo < TRIM_TMO; ++trim_tmo) { + val = qib_read_kreg64(dd, kr_ibcstatus); + if (val & IB_SERDES_TRIM_DONE) { + ret = 1; + break; + } + msleep(10); + } + if (trim_tmo >= TRIM_TMO) { + qib_dev_err(dd, "No TRIMDONE in %d tries\n", trim_tmo); + ret = 0; + } + return ret; +} + +#define TX_FAST_ELT (9) + +/* + * Set the "negotiation" values for SERDES. These are used by the IB1.2 + * link negotiation. Macros below are attempt to keep the values a + * little more human-editable. + * First, values related to Drive De-emphasis Settings. + */ + +#define NUM_DDS_REGS 6 +#define DDS_REG_MAP 0x76A910 /* LSB-first list of regs (in elt 9) to mod */ + +#define DDS_VAL(amp_d, main_d, ipst_d, ipre_d, amp_s, main_s, ipst_s, ipre_s) \ + { { ((amp_d & 0x1F) << 1) | 1, ((amp_s & 0x1F) << 1) | 1, \ + (main_d << 3) | 4 | (ipre_d >> 2), \ + (main_s << 3) | 4 | (ipre_s >> 2), \ + ((ipst_d & 0xF) << 1) | ((ipre_d & 3) << 6) | 0x21, \ + ((ipst_s & 0xF) << 1) | ((ipre_s & 3) << 6) | 0x21 } } + +static struct dds_init { + uint8_t reg_vals[NUM_DDS_REGS]; +} dds_init_vals[] = { + /* DDR(FDR) SDR(HDR) */ + /* Vendor recommends below for 3m cable */ +#define DDS_3M 0 + DDS_VAL(31, 19, 12, 0, 29, 22, 9, 0), + DDS_VAL(31, 12, 15, 4, 31, 15, 15, 1), + DDS_VAL(31, 13, 15, 3, 31, 16, 15, 0), + DDS_VAL(31, 14, 15, 2, 31, 17, 14, 0), + DDS_VAL(31, 15, 15, 1, 31, 18, 13, 0), + DDS_VAL(31, 16, 15, 0, 31, 19, 12, 0), + DDS_VAL(31, 17, 14, 0, 31, 20, 11, 0), + DDS_VAL(31, 18, 13, 0, 30, 21, 10, 0), + DDS_VAL(31, 20, 11, 0, 28, 23, 8, 0), + DDS_VAL(31, 21, 10, 0, 27, 24, 7, 0), + DDS_VAL(31, 22, 9, 0, 26, 25, 6, 0), + DDS_VAL(30, 23, 8, 0, 25, 26, 5, 0), + DDS_VAL(29, 24, 7, 0, 23, 27, 4, 0), + /* Vendor recommends below for 1m cable */ +#define DDS_1M 13 + DDS_VAL(28, 25, 6, 0, 21, 28, 3, 0), + DDS_VAL(27, 26, 5, 0, 19, 29, 2, 0), + DDS_VAL(25, 27, 4, 0, 17, 30, 1, 0) +}; + +/* + * Now the RXEQ section of the table. + */ +/* Hardware packs an element number and register address thus: */ +#define RXEQ_INIT_RDESC(elt, addr) (((elt) & 0xF) | ((addr) << 4)) +#define RXEQ_VAL(elt, adr, val0, val1, val2, val3) \ + {RXEQ_INIT_RDESC((elt), (adr)), {(val0), (val1), (val2), (val3)} } + +#define RXEQ_VAL_ALL(elt, adr, val) \ + {RXEQ_INIT_RDESC((elt), (adr)), {(val), (val), (val), (val)} } + +#define RXEQ_SDR_DFELTH 0 +#define RXEQ_SDR_TLTH 0 +#define RXEQ_SDR_G1CNT_Z1CNT 0x11 +#define RXEQ_SDR_ZCNT 23 + +static struct rxeq_init { + u16 rdesc; /* in form used in SerDesDDSRXEQ */ + u8 rdata[4]; +} rxeq_init_vals[] = { + /* Set Rcv Eq. to Preset node */ + RXEQ_VAL_ALL(7, 0x27, 0x10), + /* Set DFELTHFDR/HDR thresholds */ + RXEQ_VAL(7, 8, 0, 0, 0, 0), /* FDR, was 0, 1, 2, 3 */ + RXEQ_VAL(7, 0x21, 0, 0, 0, 0), /* HDR */ + /* Set TLTHFDR/HDR theshold */ + RXEQ_VAL(7, 9, 2, 2, 2, 2), /* FDR, was 0, 2, 4, 6 */ + RXEQ_VAL(7, 0x23, 2, 2, 2, 2), /* HDR, was 0, 1, 2, 3 */ + /* Set Preamp setting 2 (ZFR/ZCNT) */ + RXEQ_VAL(7, 0x1B, 12, 12, 12, 12), /* FDR, was 12, 16, 20, 24 */ + RXEQ_VAL(7, 0x1C, 12, 12, 12, 12), /* HDR, was 12, 16, 20, 24 */ + /* Set Preamp DC gain and Setting 1 (GFR/GHR) */ + RXEQ_VAL(7, 0x1E, 16, 16, 16, 16), /* FDR, was 16, 17, 18, 20 */ + RXEQ_VAL(7, 0x1F, 16, 16, 16, 16), /* HDR, was 16, 17, 18, 20 */ + /* Toggle RELOCK (in VCDL_CTRL0) to lock to data */ + RXEQ_VAL_ALL(6, 6, 0x20), /* Set D5 High */ + RXEQ_VAL_ALL(6, 6, 0), /* Set D5 Low */ +}; + +/* There are 17 values from vendor, but IBC only accesses the first 16 */ +#define DDS_ROWS (16) +#define RXEQ_ROWS ARRAY_SIZE(rxeq_init_vals) + +static int qib_sd_setvals(struct qib_devdata *dd) +{ + int idx, midx; + int min_idx; /* Minimum index for this portion of table */ + uint32_t dds_reg_map; + u64 __iomem *taddr, *iaddr; + uint64_t data; + uint64_t sdctl; + + taddr = dd->kregbase + kr_serdes_maptable; + iaddr = dd->kregbase + kr_serdes_ddsrxeq0; + + /* + * Init the DDS section of the table. + * Each "row" of the table provokes NUM_DDS_REG writes, to the + * registers indicated in DDS_REG_MAP. + */ + sdctl = qib_read_kreg64(dd, kr_ibserdesctrl); + sdctl = (sdctl & ~(0x1f << 8)) | (NUM_DDS_REGS << 8); + sdctl = (sdctl & ~(0x1f << 13)) | (RXEQ_ROWS << 13); + qib_write_kreg(dd, kr_ibserdesctrl, sdctl); + + /* + * Iterate down table within loop for each register to store. + */ + dds_reg_map = DDS_REG_MAP; + for (idx = 0; idx < NUM_DDS_REGS; ++idx) { + data = ((dds_reg_map & 0xF) << 4) | TX_FAST_ELT; + writeq(data, iaddr + idx); + mmiowb(); + qib_read_kreg32(dd, kr_scratch); + dds_reg_map >>= 4; + for (midx = 0; midx < DDS_ROWS; ++midx) { + u64 __iomem *daddr = taddr + ((midx << 4) + idx); + data = dds_init_vals[midx].reg_vals[idx]; + writeq(data, daddr); + mmiowb(); + qib_read_kreg32(dd, kr_scratch); + } /* End inner for (vals for this reg, each row) */ + } /* end outer for (regs to be stored) */ + + /* + * Init the RXEQ section of the table. + * This runs in a different order, as the pattern of + * register references is more complex, but there are only + * four "data" values per register. + */ + min_idx = idx; /* RXEQ indices pick up where DDS left off */ + taddr += 0x100; /* RXEQ data is in second half of table */ + /* Iterate through RXEQ register addresses */ + for (idx = 0; idx < RXEQ_ROWS; ++idx) { + int didx; /* "destination" */ + int vidx; + + /* didx is offset by min_idx to address RXEQ range of regs */ + didx = idx + min_idx; + /* Store the next RXEQ register address */ + writeq(rxeq_init_vals[idx].rdesc, iaddr + didx); + mmiowb(); + qib_read_kreg32(dd, kr_scratch); + /* Iterate through RXEQ values */ + for (vidx = 0; vidx < 4; vidx++) { + data = rxeq_init_vals[idx].rdata[vidx]; + writeq(data, taddr + (vidx << 6) + idx); + mmiowb(); + qib_read_kreg32(dd, kr_scratch); + } + } /* end outer for (Reg-writes for RXEQ) */ + return 0; +} + +#define CMUCTRL5 EPB_LOC(7, 0, 0x15) +#define RXHSCTRL0(chan) EPB_LOC(chan, 6, 0) +#define VCDL_DAC2(chan) EPB_LOC(chan, 6, 5) +#define VCDL_CTRL0(chan) EPB_LOC(chan, 6, 6) +#define VCDL_CTRL2(chan) EPB_LOC(chan, 6, 8) +#define START_EQ2(chan) EPB_LOC(chan, 7, 0x28) + +/* + * Repeat a "store" across all channels of the IB SerDes. + * Although nominally it inherits the "read value" of the last + * channel it modified, the only really useful return is <0 for + * failure, >= 0 for success. The parameter 'loc' is assumed to + * be the location in some channel of the register to be modified + * The caller can specify use of the "gang write" option of EPB, + * in which case we use the specified channel data for any fields + * not explicitely written. + */ +static int ibsd_mod_allchnls(struct qib_devdata *dd, int loc, int val, + int mask) +{ + int ret = -1; + int chnl; + + if (loc & EPB_GLOBAL_WR) { + /* + * Our caller has assured us that we can set all four + * channels at once. Trust that. If mask is not 0xFF, + * we will read the _specified_ channel for our starting + * value. + */ + loc |= (1U << EPB_IB_QUAD0_CS_SHF); + chnl = (loc >> (4 + EPB_ADDR_SHF)) & 7; + if (mask != 0xFF) { + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, + loc & ~EPB_GLOBAL_WR, 0, 0); + if (ret < 0) { + int sloc = loc >> EPB_ADDR_SHF; + + qib_dev_err(dd, "pre-read failed: elt %d," + " addr 0x%X, chnl %d\n", + (sloc & 0xF), + (sloc >> 9) & 0x3f, chnl); + return ret; + } + val = (ret & ~mask) | (val & mask); + } + loc &= ~(7 << (4+EPB_ADDR_SHF)); + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, loc, val, 0xFF); + if (ret < 0) { + int sloc = loc >> EPB_ADDR_SHF; + + qib_dev_err(dd, "Global WR failed: elt %d," + " addr 0x%X, val %02X\n", + (sloc & 0xF), (sloc >> 9) & 0x3f, val); + } + return ret; + } + /* Clear "channel" and set CS so we can simply iterate */ + loc &= ~(7 << (4+EPB_ADDR_SHF)); + loc |= (1U << EPB_IB_QUAD0_CS_SHF); + for (chnl = 0; chnl < 4; ++chnl) { + int cloc = loc | (chnl << (4+EPB_ADDR_SHF)); + + ret = qib_sd7220_reg_mod(dd, IB_7220_SERDES, cloc, val, mask); + if (ret < 0) { + int sloc = loc >> EPB_ADDR_SHF; + + qib_dev_err(dd, "Write failed: elt %d," + " addr 0x%X, chnl %d, val 0x%02X," + " mask 0x%02X\n", + (sloc & 0xF), (sloc >> 9) & 0x3f, chnl, + val & 0xFF, mask & 0xFF); + break; + } + } + return ret; +} + +/* + * Set the Tx values normally modified by IBC in IB1.2 mode to default + * values, as gotten from first row of init table. + */ +static int set_dds_vals(struct qib_devdata *dd, struct dds_init *ddi) +{ + int ret; + int idx, reg, data; + uint32_t regmap; + + regmap = DDS_REG_MAP; + for (idx = 0; idx < NUM_DDS_REGS; ++idx) { + reg = (regmap & 0xF); + regmap >>= 4; + data = ddi->reg_vals[idx]; + /* Vendor says RMW not needed for these regs, use 0xFF mask */ + ret = ibsd_mod_allchnls(dd, EPB_LOC(0, 9, reg), data, 0xFF); + if (ret < 0) + break; + } + return ret; +} + +/* + * Set the Rx values normally modified by IBC in IB1.2 mode to default + * values, as gotten from selected column of init table. + */ +static int set_rxeq_vals(struct qib_devdata *dd, int vsel) +{ + int ret; + int ridx; + int cnt = ARRAY_SIZE(rxeq_init_vals); + + for (ridx = 0; ridx < cnt; ++ridx) { + int elt, reg, val, loc; + + elt = rxeq_init_vals[ridx].rdesc & 0xF; + reg = rxeq_init_vals[ridx].rdesc >> 4; + loc = EPB_LOC(0, elt, reg); + val = rxeq_init_vals[ridx].rdata[vsel]; + /* mask of 0xFF, because hardware does full-byte store. */ + ret = ibsd_mod_allchnls(dd, loc, val, 0xFF); + if (ret < 0) + break; + } + return ret; +} + +/* + * Set the default values (row 0) for DDR Driver Demphasis. + * we do this initially and whenever we turn off IB-1.2 + * + * The "default" values for Rx equalization are also stored to + * SerDes registers. Formerly (and still default), we used set 2. + * For experimenting with cables and link-partners, we allow changing + * that via a module parameter. + */ +static unsigned qib_rxeq_set = 2; +module_param_named(rxeq_default_set, qib_rxeq_set, uint, + S_IWUSR | S_IRUGO); +MODULE_PARM_DESC(rxeq_default_set, + "Which set [0..3] of Rx Equalization values is default"); + +static int qib_internal_presets(struct qib_devdata *dd) +{ + int ret = 0; + + ret = set_dds_vals(dd, dds_init_vals + DDS_3M); + + if (ret < 0) + qib_dev_err(dd, "Failed to set default DDS values\n"); + ret = set_rxeq_vals(dd, qib_rxeq_set & 3); + if (ret < 0) + qib_dev_err(dd, "Failed to set default RXEQ values\n"); + return ret; +} + +int qib_sd7220_presets(struct qib_devdata *dd) +{ + int ret = 0; + + if (!dd->cspec->presets_needed) + return ret; + dd->cspec->presets_needed = 0; + /* Assert uC reset, so we don't clash with it. */ + qib_ibsd_reset(dd, 1); + udelay(2); + qib_sd_trimdone_monitor(dd, "link-down"); + + ret = qib_internal_presets(dd); + return ret; +} + +static int qib_sd_trimself(struct qib_devdata *dd, int val) +{ + int loc = CMUCTRL5 | (1U << EPB_IB_QUAD0_CS_SHF); + + return qib_sd7220_reg_mod(dd, IB_7220_SERDES, loc, val, 0xFF); +} + +static int qib_sd_early(struct qib_devdata *dd) +{ + int ret; + + ret = ibsd_mod_allchnls(dd, RXHSCTRL0(0) | EPB_GLOBAL_WR, 0xD4, 0xFF); + if (ret < 0) + goto bail; + ret = ibsd_mod_allchnls(dd, START_EQ1(0) | EPB_GLOBAL_WR, 0x10, 0xFF); + if (ret < 0) + goto bail; + ret = ibsd_mod_allchnls(dd, START_EQ2(0) | EPB_GLOBAL_WR, 0x30, 0xFF); +bail: + return ret; +} + +#define BACTRL(chnl) EPB_LOC(chnl, 6, 0x0E) +#define LDOUTCTRL1(chnl) EPB_LOC(chnl, 7, 6) +#define RXHSSTATUS(chnl) EPB_LOC(chnl, 6, 0xF) + +static int qib_sd_dactrim(struct qib_devdata *dd) +{ + int ret; + + ret = ibsd_mod_allchnls(dd, VCDL_DAC2(0) | EPB_GLOBAL_WR, 0x2D, 0xFF); + if (ret < 0) + goto bail; + + /* more fine-tuning of what will be default */ + ret = ibsd_mod_allchnls(dd, VCDL_CTRL2(0), 3, 0xF); + if (ret < 0) + goto bail; + + ret = ibsd_mod_allchnls(dd, BACTRL(0) | EPB_GLOBAL_WR, 0x40, 0xFF); + if (ret < 0) + goto bail; + + ret = ibsd_mod_allchnls(dd, LDOUTCTRL1(0) | EPB_GLOBAL_WR, 0x04, 0xFF); + if (ret < 0) + goto bail; + + ret = ibsd_mod_allchnls(dd, RXHSSTATUS(0) | EPB_GLOBAL_WR, 0x04, 0xFF); + if (ret < 0) + goto bail; + + /* + * Delay for max possible number of steps, with slop. + * Each step is about 4usec. + */ + udelay(415); + + ret = ibsd_mod_allchnls(dd, LDOUTCTRL1(0) | EPB_GLOBAL_WR, 0x00, 0xFF); + +bail: + return ret; +} + +#define RELOCK_FIRST_MS 3 +#define RXLSPPM(chan) EPB_LOC(chan, 0, 2) +void toggle_7220_rclkrls(struct qib_devdata *dd) +{ + int loc = RXLSPPM(0) | EPB_GLOBAL_WR; + int ret; + + ret = ibsd_mod_allchnls(dd, loc, 0, 0x80); + if (ret < 0) + qib_dev_err(dd, "RCLKRLS failed to clear D7\n"); + else { + udelay(1); + ibsd_mod_allchnls(dd, loc, 0x80, 0x80); + } + /* And again for good measure */ + udelay(1); + ret = ibsd_mod_allchnls(dd, loc, 0, 0x80); + if (ret < 0) + qib_dev_err(dd, "RCLKRLS failed to clear D7\n"); + else { + udelay(1); + ibsd_mod_allchnls(dd, loc, 0x80, 0x80); + } + /* Now reset xgxs and IBC to complete the recovery */ + dd->f_xgxs_reset(dd->pport); +} + +/* + * Shut down the timer that polls for relock occasions, if needed + * this is "hooked" from qib_7220_quiet_serdes(), which is called + * just before qib_shutdown_device() in qib_driver.c shuts down all + * the other timers + */ +void shutdown_7220_relock_poll(struct qib_devdata *dd) +{ + if (dd->cspec->relock_timer_active) + del_timer_sync(&dd->cspec->relock_timer); +} + +static unsigned qib_relock_by_timer = 1; +module_param_named(relock_by_timer, qib_relock_by_timer, uint, + S_IWUSR | S_IRUGO); +MODULE_PARM_DESC(relock_by_timer, "Allow relock attempt if link not up"); + +static void qib_run_relock(unsigned long opaque) +{ + struct qib_devdata *dd = (struct qib_devdata *)opaque; + struct qib_pportdata *ppd = dd->pport; + struct qib_chip_specific *cs = dd->cspec; + int timeoff; + + /* + * Check link-training state for "stuck" state, when down. + * if found, try relock and schedule another try at + * exponentially growing delay, maxed at one second. + * if not stuck, our work is done. + */ + if ((dd->flags & QIB_INITTED) && !(ppd->lflags & + (QIBL_IB_AUTONEG_INPROG | QIBL_LINKINIT | QIBL_LINKARMED | + QIBL_LINKACTIVE))) { + if (qib_relock_by_timer) { + if (!(ppd->lflags & QIBL_IB_LINK_DISABLED)) + toggle_7220_rclkrls(dd); + } + /* re-set timer for next check */ + timeoff = cs->relock_interval << 1; + if (timeoff > HZ) + timeoff = HZ; + cs->relock_interval = timeoff; + } else + timeoff = HZ; + mod_timer(&cs->relock_timer, jiffies + timeoff); +} + +void set_7220_relock_poll(struct qib_devdata *dd, int ibup) +{ + struct qib_chip_specific *cs = dd->cspec; + + if (ibup) { + /* We are now up, relax timer to 1 second interval */ + if (cs->relock_timer_active) { + cs->relock_interval = HZ; + mod_timer(&cs->relock_timer, jiffies + HZ); + } + } else { + /* Transition to down, (re-)set timer to short interval. */ + unsigned int timeout; + + timeout = msecs_to_jiffies(RELOCK_FIRST_MS); + if (timeout == 0) + timeout = 1; + /* If timer has not yet been started, do so. */ + if (!cs->relock_timer_active) { + cs->relock_timer_active = 1; + init_timer(&cs->relock_timer); + cs->relock_timer.function = qib_run_relock; + cs->relock_timer.data = (unsigned long) dd; + cs->relock_interval = timeout; + cs->relock_timer.expires = jiffies + timeout; + add_timer(&cs->relock_timer); + } else { + cs->relock_interval = timeout; + mod_timer(&cs->relock_timer, jiffies + timeout); + } + } +} |