summaryrefslogtreecommitdiff
path: root/drivers/mmc/host/mmci.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/mmc/host/mmci.c')
-rw-r--r--drivers/mmc/host/mmci.c207
1 files changed, 177 insertions, 30 deletions
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 87b4fc6c98c2..563022825667 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -19,6 +19,7 @@
#include <linux/highmem.h>
#include <linux/log2.h>
#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
#include <linux/amba/bus.h>
#include <linux/clk.h>
#include <linux/scatterlist.h>
@@ -45,6 +46,12 @@ static unsigned int fmax = 515633;
* is asserted (likewise for RX)
* @fifohalfsize: number of bytes that can be written when MCI_TXFIFOHALFEMPTY
* is asserted (likewise for RX)
+ * @broken_blockend: the MCI_DATABLOCKEND is broken on the hardware
+ * and will not work at all.
+ * @broken_blockend_dma: the MCI_DATABLOCKEND is broken on the hardware when
+ * using DMA.
+ * @sdio: variant supports SDIO
+ * @st_clkdiv: true if using a ST-specific clock divider algorithm
*/
struct variant_data {
unsigned int clkreg;
@@ -52,6 +59,10 @@ struct variant_data {
unsigned int datalength_bits;
unsigned int fifosize;
unsigned int fifohalfsize;
+ bool broken_blockend;
+ bool broken_blockend_dma;
+ bool sdio;
+ bool st_clkdiv;
};
static struct variant_data variant_arm = {
@@ -65,6 +76,8 @@ static struct variant_data variant_u300 = {
.fifohalfsize = 8 * 4,
.clkreg_enable = 1 << 13, /* HWFCEN */
.datalength_bits = 16,
+ .broken_blockend_dma = true,
+ .sdio = true,
};
static struct variant_data variant_ux500 = {
@@ -73,7 +86,11 @@ static struct variant_data variant_ux500 = {
.clkreg = MCI_CLK_ENABLE,
.clkreg_enable = 1 << 14, /* HWFCEN */
.datalength_bits = 24,
+ .broken_blockend = true,
+ .sdio = true,
+ .st_clkdiv = true,
};
+
/*
* This must be called with host->lock held
*/
@@ -86,7 +103,22 @@ static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
if (desired >= host->mclk) {
clk = MCI_CLK_BYPASS;
host->cclk = host->mclk;
+ } else if (variant->st_clkdiv) {
+ /*
+ * DB8500 TRM says f = mclk / (clkdiv + 2)
+ * => clkdiv = (mclk / f) - 2
+ * Round the divider up so we don't exceed the max
+ * frequency
+ */
+ clk = DIV_ROUND_UP(host->mclk, desired) - 2;
+ if (clk >= 256)
+ clk = 255;
+ host->cclk = host->mclk / (clk + 2);
} else {
+ /*
+ * PL180 TRM says f = mclk / (2 * (clkdiv + 1))
+ * => clkdiv = mclk / (2 * f) - 1
+ */
clk = host->mclk / (2 * desired) - 1;
if (clk >= 256)
clk = 255;
@@ -129,10 +161,26 @@ mmci_request_end(struct mmci_host *host, struct mmc_request *mrq)
spin_lock(&host->lock);
}
+static void mmci_set_mask1(struct mmci_host *host, unsigned int mask)
+{
+ void __iomem *base = host->base;
+
+ if (host->singleirq) {
+ unsigned int mask0 = readl(base + MMCIMASK0);
+
+ mask0 &= ~MCI_IRQ1MASK;
+ mask0 |= mask;
+
+ writel(mask0, base + MMCIMASK0);
+ }
+
+ writel(mask, base + MMCIMASK1);
+}
+
static void mmci_stop_data(struct mmci_host *host)
{
writel(0, host->base + MMCIDATACTRL);
- writel(0, host->base + MMCIMASK1);
+ mmci_set_mask1(host, 0);
host->data = NULL;
}
@@ -162,6 +210,8 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data)
host->data = data;
host->size = data->blksz * data->blocks;
host->data_xfered = 0;
+ host->blockend = false;
+ host->dataend = false;
mmci_init_sg(host, data);
@@ -196,9 +246,14 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data)
irqmask = MCI_TXFIFOHALFEMPTYMASK;
}
+ /* The ST Micro variants has a special bit to enable SDIO */
+ if (variant->sdio && host->mmc->card)
+ if (mmc_card_sdio(host->mmc->card))
+ datactrl |= MCI_ST_DPSM_SDIOEN;
+
writel(datactrl, base + MMCIDATACTRL);
writel(readl(base + MMCIMASK0) & ~MCI_DATAENDMASK, base + MMCIMASK0);
- writel(irqmask, base + MMCIMASK1);
+ mmci_set_mask1(host, irqmask);
}
static void
@@ -233,20 +288,9 @@ static void
mmci_data_irq(struct mmci_host *host, struct mmc_data *data,
unsigned int status)
{
- if (status & MCI_DATABLOCKEND) {
- host->data_xfered += data->blksz;
-#ifdef CONFIG_ARCH_U300
- /*
- * On the U300 some signal or other is
- * badly routed so that a data write does
- * not properly terminate with a MCI_DATAEND
- * status flag. This quirk will make writes
- * work again.
- */
- if (data->flags & MMC_DATA_WRITE)
- status |= MCI_DATAEND;
-#endif
- }
+ struct variant_data *variant = host->variant;
+
+ /* First check for errors */
if (status & (MCI_DATACRCFAIL|MCI_DATATIMEOUT|MCI_TXUNDERRUN|MCI_RXOVERRUN)) {
dev_dbg(mmc_dev(host->mmc), "MCI ERROR IRQ (status %08x)\n", status);
if (status & MCI_DATACRCFAIL)
@@ -255,7 +299,10 @@ mmci_data_irq(struct mmci_host *host, struct mmc_data *data,
data->error = -ETIMEDOUT;
else if (status & (MCI_TXUNDERRUN|MCI_RXOVERRUN))
data->error = -EIO;
- status |= MCI_DATAEND;
+
+ /* Force-complete the transaction */
+ host->blockend = true;
+ host->dataend = true;
/*
* We hit an error condition. Ensure that any data
@@ -273,9 +320,64 @@ mmci_data_irq(struct mmci_host *host, struct mmc_data *data,
local_irq_restore(flags);
}
}
- if (status & MCI_DATAEND) {
+
+ /*
+ * On ARM variants in PIO mode, MCI_DATABLOCKEND
+ * is always sent first, and we increase the
+ * transfered number of bytes for that IRQ. Then
+ * MCI_DATAEND follows and we conclude the transaction.
+ *
+ * On the Ux500 single-IRQ variant MCI_DATABLOCKEND
+ * doesn't seem to immediately clear from the status,
+ * so we can't use it keep count when only one irq is
+ * used because the irq will hit for other reasons, and
+ * then the flag is still up. So we use the MCI_DATAEND
+ * IRQ at the end of the entire transfer because
+ * MCI_DATABLOCKEND is broken.
+ *
+ * In the U300, the IRQs can arrive out-of-order,
+ * e.g. MCI_DATABLOCKEND sometimes arrives after MCI_DATAEND,
+ * so for this case we use the flags "blockend" and
+ * "dataend" to make sure both IRQs have arrived before
+ * concluding the transaction. (This does not apply
+ * to the Ux500 which doesn't fire MCI_DATABLOCKEND
+ * at all.) In DMA mode it suffers from the same problem
+ * as the Ux500.
+ */
+ if (status & MCI_DATABLOCKEND) {
+ /*
+ * Just being a little over-cautious, we do not
+ * use this progressive update if the hardware blockend
+ * flag is unreliable: since it can stay high between
+ * IRQs it will corrupt the transfer counter.
+ */
+ if (!variant->broken_blockend)
+ host->data_xfered += data->blksz;
+ host->blockend = true;
+ }
+
+ if (status & MCI_DATAEND)
+ host->dataend = true;
+
+ /*
+ * On variants with broken blockend we shall only wait for dataend,
+ * on others we must sync with the blockend signal since they can
+ * appear out-of-order.
+ */
+ if (host->dataend && (host->blockend || variant->broken_blockend)) {
mmci_stop_data(host);
+ /* Reset these flags */
+ host->blockend = false;
+ host->dataend = false;
+
+ /*
+ * Variants with broken blockend flags need to handle the
+ * end of the entire transfer here.
+ */
+ if (variant->broken_blockend && !data->error)
+ host->data_xfered += data->blksz * data->blocks;
+
if (!data->stop) {
mmci_request_end(host, data->mrq);
} else {
@@ -356,7 +458,32 @@ static int mmci_pio_write(struct mmci_host *host, char *buffer, unsigned int rem
variant->fifosize : variant->fifohalfsize;
count = min(remain, maxcnt);
- writesl(base + MMCIFIFO, ptr, count >> 2);
+ /*
+ * The ST Micro variant for SDIO transfer sizes
+ * less then 8 bytes should have clock H/W flow
+ * control disabled.
+ */
+ if (variant->sdio &&
+ mmc_card_sdio(host->mmc->card)) {
+ if (count < 8)
+ writel(readl(host->base + MMCICLOCK) &
+ ~variant->clkreg_enable,
+ host->base + MMCICLOCK);
+ else
+ writel(readl(host->base + MMCICLOCK) |
+ variant->clkreg_enable,
+ host->base + MMCICLOCK);
+ }
+
+ /*
+ * SDIO especially may want to send something that is
+ * not divisible by 4 (as opposed to card sectors
+ * etc), and the FIFO only accept full 32-bit writes.
+ * So compensate by adding +3 on the count, a single
+ * byte become a 32bit write, 7 bytes will be two
+ * 32bit writes etc.
+ */
+ writesl(base + MMCIFIFO, ptr, (count + 3) >> 2);
ptr += count;
remain -= count;
@@ -437,7 +564,7 @@ static irqreturn_t mmci_pio_irq(int irq, void *dev_id)
* "any data available" mode.
*/
if (status & MCI_RXACTIVE && host->size < variant->fifosize)
- writel(MCI_RXDATAAVLBLMASK, base + MMCIMASK1);
+ mmci_set_mask1(host, MCI_RXDATAAVLBLMASK);
/*
* If we run out of data, disable the data IRQs; this
@@ -446,7 +573,7 @@ static irqreturn_t mmci_pio_irq(int irq, void *dev_id)
* stops us racing with our data end IRQ.
*/
if (host->size == 0) {
- writel(0, base + MMCIMASK1);
+ mmci_set_mask1(host, 0);
writel(readl(base + MMCIMASK0) | MCI_DATAENDMASK, base + MMCIMASK0);
}
@@ -469,6 +596,14 @@ static irqreturn_t mmci_irq(int irq, void *dev_id)
struct mmc_data *data;
status = readl(host->base + MMCISTATUS);
+
+ if (host->singleirq) {
+ if (status & readl(host->base + MMCIMASK1))
+ mmci_pio_irq(irq, dev_id);
+
+ status &= ~MCI_IRQ1MASK;
+ }
+
status &= readl(host->base + MMCIMASK0);
writel(status, host->base + MMCICLEAR);
@@ -635,6 +770,7 @@ static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id)
struct variant_data *variant = id->data;
struct mmci_host *host;
struct mmc_host *mmc;
+ unsigned int mask;
int ret;
/* must have platform data */
@@ -806,20 +942,30 @@ static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id)
if (ret)
goto unmap;
- ret = request_irq(dev->irq[1], mmci_pio_irq, IRQF_SHARED, DRIVER_NAME " (pio)", host);
- if (ret)
- goto irq0_free;
+ if (dev->irq[1] == NO_IRQ)
+ host->singleirq = true;
+ else {
+ ret = request_irq(dev->irq[1], mmci_pio_irq, IRQF_SHARED,
+ DRIVER_NAME " (pio)", host);
+ if (ret)
+ goto irq0_free;
+ }
- writel(MCI_IRQENABLE, host->base + MMCIMASK0);
+ mask = MCI_IRQENABLE;
+ /* Don't use the datablockend flag if it's broken */
+ if (variant->broken_blockend)
+ mask &= ~MCI_DATABLOCKEND;
- amba_set_drvdata(dev, mmc);
+ writel(mask, host->base + MMCIMASK0);
- mmc_add_host(mmc);
+ amba_set_drvdata(dev, mmc);
- dev_info(&dev->dev, "%s: MMCI rev %x cfg %02x at 0x%016llx irq %d,%d\n",
- mmc_hostname(mmc), amba_rev(dev), amba_config(dev),
+ dev_info(&dev->dev, "%s: PL%03x rev%u at 0x%08llx irq %d,%d\n",
+ mmc_hostname(mmc), amba_part(dev), amba_rev(dev),
(unsigned long long)dev->res.start, dev->irq[0], dev->irq[1]);
+ mmc_add_host(mmc);
+
return 0;
irq0_free:
@@ -864,7 +1010,8 @@ static int __devexit mmci_remove(struct amba_device *dev)
writel(0, host->base + MMCIDATACTRL);
free_irq(dev->irq[0], host);
- free_irq(dev->irq[1], host);
+ if (!host->singleirq)
+ free_irq(dev->irq[1], host);
if (host->gpio_wp != -ENOSYS)
gpio_free(host->gpio_wp);