summaryrefslogtreecommitdiff
path: root/drivers/net/ixgbe/ixgbe_82598.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/ixgbe/ixgbe_82598.c')
-rw-r--r--drivers/net/ixgbe/ixgbe_82598.c102
1 files changed, 69 insertions, 33 deletions
diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c
index d0f1d9d2c416..845c679c8b87 100644
--- a/drivers/net/ixgbe/ixgbe_82598.c
+++ b/drivers/net/ixgbe/ixgbe_82598.c
@@ -1,7 +1,7 @@
/*******************************************************************************
Intel 10 Gigabit PCI Express Linux driver
- Copyright(c) 1999 - 2010 Intel Corporation.
+ Copyright(c) 1999 - 2011 Intel Corporation.
This program is free software; you can redistribute it and/or modify it
under the terms and conditions of the GNU General Public License,
@@ -158,6 +158,7 @@ static s32 ixgbe_init_phy_ops_82598(struct ixgbe_hw *hw)
switch (hw->phy.type) {
case ixgbe_phy_tn:
+ phy->ops.setup_link = &ixgbe_setup_phy_link_tnx;
phy->ops.check_link = &ixgbe_check_phy_link_tnx;
phy->ops.get_firmware_version =
&ixgbe_get_phy_firmware_version_tnx;
@@ -280,10 +281,22 @@ static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw)
{
enum ixgbe_media_type media_type;
+ /* Detect if there is a copper PHY attached. */
+ switch (hw->phy.type) {
+ case ixgbe_phy_cu_unknown:
+ case ixgbe_phy_tn:
+ case ixgbe_phy_aq:
+ media_type = ixgbe_media_type_copper;
+ goto out;
+ default:
+ break;
+ }
+
/* Media type for I82598 is based on device ID */
switch (hw->device_id) {
case IXGBE_DEV_ID_82598:
case IXGBE_DEV_ID_82598_BX:
+ /* Default device ID is mezzanine card KX/KX4 */
media_type = ixgbe_media_type_backplane;
break;
case IXGBE_DEV_ID_82598AF_DUAL_PORT:
@@ -306,7 +319,7 @@ static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw)
media_type = ixgbe_media_type_unknown;
break;
}
-
+out:
return media_type;
}
@@ -354,7 +367,7 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
/* Negotiate the fc mode to use */
ret_val = ixgbe_fc_autoneg(hw);
- if (ret_val)
+ if (ret_val == IXGBE_ERR_FLOW_CONTROL)
goto out;
/* Disable any previous flow control settings */
@@ -372,10 +385,10 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
* 2: Tx flow control is enabled (we can send pause frames but
* we do not support receiving pause frames).
* 3: Both Rx and Tx flow control (symmetric) are enabled.
- * other: Invalid.
#ifdef CONFIG_DCB
* 4: Priority Flow Control is enabled.
#endif
+ * other: Invalid.
*/
switch (hw->fc.current_mode) {
case ixgbe_fc_none:
@@ -432,9 +445,10 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
reg = (rx_pba_size - hw->fc.low_water) << 6;
if (hw->fc.send_xon)
reg |= IXGBE_FCRTL_XONE;
+
IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num), reg);
- reg = (rx_pba_size - hw->fc.high_water) << 10;
+ reg = (rx_pba_size - hw->fc.high_water) << 6;
reg |= IXGBE_FCRTH_FCEN;
IXGBE_WRITE_REG(hw, IXGBE_FCRTH(packetbuf_num), reg);
@@ -627,13 +641,12 @@ out:
return 0;
}
-
/**
* ixgbe_setup_mac_link_82598 - Set MAC link speed
* @hw: pointer to hardware structure
* @speed: new link speed
* @autoneg: true if auto-negotiation enabled
- * @autoneg_wait_to_complete: true if waiting is needed to complete
+ * @autoneg_wait_to_complete: true when waiting for completion is needed
*
* Set the link speed in the AUTOC register and restarts link.
**/
@@ -672,7 +685,8 @@ static s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw,
* ixgbe_hw This will write the AUTOC register based on the new
* stored values
*/
- status = ixgbe_start_mac_link_82598(hw, autoneg_wait_to_complete);
+ status = ixgbe_start_mac_link_82598(hw,
+ autoneg_wait_to_complete);
}
return status;
@@ -698,7 +712,6 @@ static s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw,
/* Setup the PHY according to input speed */
status = hw->phy.ops.setup_link_speed(hw, speed, autoneg,
autoneg_wait_to_complete);
-
/* Set up MAC */
ixgbe_start_mac_link_82598(hw, autoneg_wait_to_complete);
@@ -770,7 +783,6 @@ static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw)
else if (phy_status == IXGBE_ERR_SFP_NOT_PRESENT)
goto no_phy_reset;
-
hw->phy.ops.reset(hw);
}
@@ -779,12 +791,9 @@ no_phy_reset:
* Prevent the PCI-E bus from from hanging by disabling PCI-E master
* access and verify no pending requests before reset
*/
- status = ixgbe_disable_pcie_master(hw);
- if (status != 0) {
- status = IXGBE_ERR_MASTER_REQUESTS_PENDING;
- hw_dbg(hw, "PCI-E Master disable polling has failed.\n");
- }
+ ixgbe_disable_pcie_master(hw);
+mac_reset_top:
/*
* Issue global reset to the MAC. This needs to be a SW reset.
* If link reset is used, it might reset the MAC when mng is using it
@@ -805,6 +814,19 @@ no_phy_reset:
hw_dbg(hw, "Reset polling failed to complete.\n");
}
+ /*
+ * Double resets are required for recovery from certain error
+ * conditions. Between resets, it is necessary to stall to allow time
+ * for any pending HW events to complete. We use 1usec since that is
+ * what is needed for ixgbe_disable_pcie_master(). The second reset
+ * then clears out any effects of those events.
+ */
+ if (hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED) {
+ hw->mac.flags &= ~IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
+ udelay(1);
+ goto mac_reset_top;
+ }
+
msleep(50);
gheccr = IXGBE_READ_REG(hw, IXGBE_GHECCR);
@@ -824,15 +846,15 @@ no_phy_reset:
IXGBE_WRITE_REG(hw, IXGBE_AUTOC, hw->mac.orig_autoc);
}
+ /* Store the permanent mac address */
+ hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr);
+
/*
* Store MAC address from RAR0, clear receive address registers, and
* clear the multicast table
*/
hw->mac.ops.init_rx_addrs(hw);
- /* Store the permanent mac address */
- hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr);
-
reset_hw_out:
if (phy_status)
status = phy_status;
@@ -849,6 +871,13 @@ reset_hw_out:
static s32 ixgbe_set_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
{
u32 rar_high;
+ u32 rar_entries = hw->mac.num_rar_entries;
+
+ /* Make sure we are using a valid rar index range */
+ if (rar >= rar_entries) {
+ hw_dbg(hw, "RAR index %d is out of range.\n", rar);
+ return IXGBE_ERR_INVALID_ARGUMENT;
+ }
rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(rar));
rar_high &= ~IXGBE_RAH_VIND_MASK;
@@ -868,14 +897,17 @@ static s32 ixgbe_clear_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
u32 rar_high;
u32 rar_entries = hw->mac.num_rar_entries;
- if (rar < rar_entries) {
- rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(rar));
- if (rar_high & IXGBE_RAH_VIND_MASK) {
- rar_high &= ~IXGBE_RAH_VIND_MASK;
- IXGBE_WRITE_REG(hw, IXGBE_RAH(rar), rar_high);
- }
- } else {
+
+ /* Make sure we are using a valid rar index range */
+ if (rar >= rar_entries) {
hw_dbg(hw, "RAR index %d is out of range.\n", rar);
+ return IXGBE_ERR_INVALID_ARGUMENT;
+ }
+
+ rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(rar));
+ if (rar_high & IXGBE_RAH_VIND_MASK) {
+ rar_high &= ~IXGBE_RAH_VIND_MASK;
+ IXGBE_WRITE_REG(hw, IXGBE_RAH(rar), rar_high);
}
return 0;
@@ -994,13 +1026,12 @@ static s32 ixgbe_write_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 val)
}
/**
- * ixgbe_read_i2c_eeprom_82598 - Read 8 bit EEPROM word of an SFP+ module
- * over I2C interface through an intermediate phy.
+ * ixgbe_read_i2c_eeprom_82598 - Reads 8 bit word over I2C interface.
* @hw: pointer to hardware structure
* @byte_offset: EEPROM byte offset to read
* @eeprom_data: value read
*
- * Performs byte read operation to SFP module's EEPROM over I2C interface.
+ * Performs 8 byte read operation to SFP module's EEPROM over I2C interface.
**/
static s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset,
u8 *eeprom_data)
@@ -1074,10 +1105,12 @@ static u32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
/* Copper PHY must be checked before AUTOC LMS to determine correct
* physical layer because 10GBase-T PHYs use LMS = KX4/KX */
- if (hw->phy.type == ixgbe_phy_tn ||
- hw->phy.type == ixgbe_phy_cu_unknown) {
- hw->phy.ops.read_reg(hw, MDIO_PMA_EXTABLE, MDIO_MMD_PMAPMD,
- &ext_ability);
+ switch (hw->phy.type) {
+ case ixgbe_phy_tn:
+ case ixgbe_phy_aq:
+ case ixgbe_phy_cu_unknown:
+ hw->phy.ops.read_reg(hw, MDIO_PMA_EXTABLE,
+ MDIO_MMD_PMAPMD, &ext_ability);
if (ext_ability & MDIO_PMA_EXTABLE_10GBT)
physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T;
if (ext_ability & MDIO_PMA_EXTABLE_1000BT)
@@ -1085,6 +1118,8 @@ static u32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
if (ext_ability & MDIO_PMA_EXTABLE_100BTX)
physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX;
goto out;
+ default:
+ break;
}
switch (autoc & IXGBE_AUTOC_LMS_MASK) {
@@ -1179,13 +1214,14 @@ static struct ixgbe_mac_operations mac_ops_82598 = {
.set_vmdq = &ixgbe_set_vmdq_82598,
.clear_vmdq = &ixgbe_clear_vmdq_82598,
.init_rx_addrs = &ixgbe_init_rx_addrs_generic,
- .update_uc_addr_list = &ixgbe_update_uc_addr_list_generic,
.update_mc_addr_list = &ixgbe_update_mc_addr_list_generic,
.enable_mc = &ixgbe_enable_mc_generic,
.disable_mc = &ixgbe_disable_mc_generic,
.clear_vfta = &ixgbe_clear_vfta_82598,
.set_vfta = &ixgbe_set_vfta_82598,
.fc_enable = &ixgbe_fc_enable_82598,
+ .acquire_swfw_sync = &ixgbe_acquire_swfw_sync,
+ .release_swfw_sync = &ixgbe_release_swfw_sync,
};
static struct ixgbe_eeprom_operations eeprom_ops_82598 = {