diff options
Diffstat (limited to 'drivers/serial/Kconfig')
| -rw-r--r-- | drivers/serial/Kconfig | 135 |
1 files changed, 130 insertions, 5 deletions
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index ad9f321968e1..315ea9916456 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -5,6 +5,7 @@ # menu "Serial drivers" + depends on HAS_IOMEM # # The new 8250/16550 serial drivers @@ -73,17 +74,21 @@ config SERIAL_8250_PCI depends on SERIAL_8250 && PCI default SERIAL_8250 help - This builds standard PCI serial support. You may be able to - disable this feature if you only need legacy serial support. - Saves about 9K. + Say Y here if you have PCI serial ports. + + To compile this driver as a module, choose M here: the module + will be called 8250_pci. config SERIAL_8250_PNP tristate "8250/16550 PNP device support" if EMBEDDED depends on SERIAL_8250 && PNP default SERIAL_8250 help - This builds standard PNP serial support. You may be able to - disable this feature if you only need legacy serial support. + Say Y here if you have serial ports described by PNPBIOS or ACPI. + These are typically ports built into the system board. + + To compile this driver as a module, choose M here: the module + will be called 8250_pnp. config SERIAL_8250_HP300 tristate @@ -254,6 +259,15 @@ config SERIAL_8250_AU1X00 to this option. The driver can handle 1 or 2 serial ports. If unsure, say N. +config SERIAL_8250_RM9K + bool "Support for MIPS RM9xxx integrated serial port" + depends on SERIAL_8250 != n && SERIAL_RM9000 + select SERIAL_8250_SHARE_IRQ + help + Selecting this option will add support for the integrated serial + port hardware found on MIPS RM9122 and similar processors. + If unsure, say N. + comment "Non-8250 serial port support" config SERIAL_AMBA_PL010 @@ -345,6 +359,23 @@ config SERIAL_ATMEL_TTYAT Say Y if you have an external 8250/16C550 UART. If unsure, say N. +config SERIAL_KS8695 + bool "Micrel KS8695 (Centaur) serial port support" + depends on ARCH_KS8695 + select SERIAL_CORE + help + This selects the Micrel Centaur KS8695 UART. Say Y here. + +config SERIAL_KS8695_CONSOLE + bool "Support for console on KS8695 (Centaur) serial port" + depends on SERIAL_KS8695=y + select SERIAL_CORE_CONSOLE + help + Say Y here if you wish to use a KS8695 (Centaur) UART as the + system console (the system console is the device which + receives all kernel messages and warnings and which allows + logins in single user mode). + config SERIAL_CLPS711X tristate "CLPS711X serial port support" depends on ARM && ARCH_CLPS711X @@ -499,6 +530,100 @@ config SERIAL_SA1100_CONSOLE your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) +config SERIAL_BFIN + tristate "Blackfin serial port support" + depends on BFIN + select SERIAL_CORE + select SERIAL_BFIN_UART0 if (BF531 || BF532 || BF533 || BF561) + help + Add support for the built-in UARTs on the Blackfin. + + To compile this driver as a module, choose M here: the + module will be called bfin_5xx. + +config SERIAL_BFIN_CONSOLE + bool "Console on Blackfin serial port" + depends on SERIAL_BFIN + select SERIAL_CORE_CONSOLE + +choice + prompt "UART Mode" + depends on SERIAL_BFIN + default SERIAL_BFIN_DMA + help + This driver supports the built-in serial ports of the Blackfin family + of CPUs + +config SERIAL_BFIN_DMA + bool "DMA mode" + depends on DMA_UNCACHED_1M + help + This driver works under DMA mode. If this option is selected, the + blackfin simple dma driver is also enabled. + +config SERIAL_BFIN_PIO + bool "PIO mode" + help + This driver works under PIO mode. + +endchoice + +config SERIAL_BFIN_UART0 + bool "Enable UART0" + depends on SERIAL_BFIN + help + Enable UART0 + +config BFIN_UART0_CTSRTS + bool "Enable UART0 hardware flow control" + depends on SERIAL_BFIN_UART0 + help + Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS + signal. + +config UART0_CTS_PIN + int "UART0 CTS pin" + depends on BFIN_UART0_CTSRTS + default 23 + help + The default pin is GPIO_GP7. + Refer to ./include/asm-blackfin/gpio.h to see the GPIO map. + +config UART0_RTS_PIN + int "UART0 RTS pin" + depends on BFIN_UART0_CTSRTS + default 22 + help + The default pin is GPIO_GP6. + Refer to ./include/asm-blackfin/gpio.h to see the GPIO map. + +config SERIAL_BFIN_UART1 + bool "Enable UART1" + depends on SERIAL_BFIN && (BF534 || BF536 || BF537) + help + Enable UART1 + +config BFIN_UART1_CTSRTS + bool "Enable UART1 hardware flow control" + depends on SERIAL_BFIN_UART1 + help + Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS + signal. + +config UART1_CTS_PIN + int "UART1 CTS pin" + depends on BFIN_UART1_CTSRTS + default -1 + help + Refer to ./include/asm-blackfin/gpio.h to see the GPIO map. + +config UART1_RTS_PIN + int "UART1 RTS pin" + depends on BFIN_UART1_CTSRTS + default -1 + help + Refer to ./include/asm-blackfin/gpio.h to see the GPIO map. + config SERIAL_IMX bool "IMX serial port support" depends on ARM && ARCH_IMX |