summaryrefslogtreecommitdiff
path: root/drivers/usb/musb/blackfin.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/usb/musb/blackfin.c')
-rw-r--r--drivers/usb/musb/blackfin.c80
1 files changed, 54 insertions, 26 deletions
diff --git a/drivers/usb/musb/blackfin.c b/drivers/usb/musb/blackfin.c
index 611a9d274363..fcb5206a65bd 100644
--- a/drivers/usb/musb/blackfin.c
+++ b/drivers/usb/musb/blackfin.c
@@ -171,8 +171,9 @@ static irqreturn_t blackfin_interrupt(int irq, void *__hci)
}
/* Start sampling ID pin, when plug is removed from MUSB */
- if (is_otg_enabled(musb) && (musb->xceiv->state == OTG_STATE_B_IDLE
- || musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) {
+ if ((is_otg_enabled(musb) && (musb->xceiv->state == OTG_STATE_B_IDLE
+ || musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) ||
+ (musb->int_usb & MUSB_INTR_DISCONNECT && is_host_active(musb))) {
mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
musb->a_wait_bcon = TIMER_DELAY;
}
@@ -323,30 +324,8 @@ int musb_platform_set_mode(struct musb *musb, u8 musb_mode)
return -EIO;
}
-int __init musb_platform_init(struct musb *musb, void *board_data)
+static void musb_platform_reg_init(struct musb *musb)
{
-
- /*
- * Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
- * and OTG HOST modes, while rev 1.1 and greater require PE7 to
- * be low for DEVICE mode and high for HOST mode. We set it high
- * here because we are in host mode
- */
-
- if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
- printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d \n",
- musb->config->gpio_vrsel);
- return -ENODEV;
- }
- gpio_direction_output(musb->config->gpio_vrsel, 0);
-
- usb_nop_xceiv_register();
- musb->xceiv = otg_get_transceiver();
- if (!musb->xceiv) {
- gpio_free(musb->config->gpio_vrsel);
- return -ENODEV;
- }
-
if (ANOMALY_05000346) {
bfin_write_USB_APHY_CALIB(ANOMALY_05000346_value);
SSYNC();
@@ -358,7 +337,8 @@ int __init musb_platform_init(struct musb *musb, void *board_data)
}
/* Configure PLL oscillator register */
- bfin_write_USB_PLLOSC_CTRL(0x30a8);
+ bfin_write_USB_PLLOSC_CTRL(0x3080 |
+ ((480/musb->config->clkin) << 1));
SSYNC();
bfin_write_USB_SRP_CLKDIV((get_sclk()/1000) / 32 - 1);
@@ -380,6 +360,33 @@ int __init musb_platform_init(struct musb *musb, void *board_data)
EP2_RX_ENA | EP3_RX_ENA | EP4_RX_ENA |
EP5_RX_ENA | EP6_RX_ENA | EP7_RX_ENA);
SSYNC();
+}
+
+int __init musb_platform_init(struct musb *musb, void *board_data)
+{
+
+ /*
+ * Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
+ * and OTG HOST modes, while rev 1.1 and greater require PE7 to
+ * be low for DEVICE mode and high for HOST mode. We set it high
+ * here because we are in host mode
+ */
+
+ if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
+ printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d\n",
+ musb->config->gpio_vrsel);
+ return -ENODEV;
+ }
+ gpio_direction_output(musb->config->gpio_vrsel, 0);
+
+ usb_nop_xceiv_register();
+ musb->xceiv = otg_get_transceiver();
+ if (!musb->xceiv) {
+ gpio_free(musb->config->gpio_vrsel);
+ return -ENODEV;
+ }
+
+ musb_platform_reg_init(musb);
if (is_host_enabled(musb)) {
musb->board_set_vbus = bfin_set_vbus;
@@ -394,6 +401,27 @@ int __init musb_platform_init(struct musb *musb, void *board_data)
return 0;
}
+#ifdef CONFIG_PM
+void musb_platform_save_context(struct musb *musb,
+ struct musb_context_registers *musb_context)
+{
+ if (is_host_active(musb))
+ /*
+ * During hibernate gpio_vrsel will change from high to low
+ * low which will generate wakeup event resume the system
+ * immediately. Set it to 0 before hibernate to avoid this
+ * wakeup event.
+ */
+ gpio_set_value(musb->config->gpio_vrsel, 0);
+}
+
+void musb_platform_restore_context(struct musb *musb,
+ struct musb_context_registers *musb_context)
+{
+ musb_platform_reg_init(musb);
+}
+#endif
+
int musb_platform_exit(struct musb *musb)
{
gpio_free(musb->config->gpio_vrsel);