summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-12-17mtd: spear_smi: Fix Write Burst modeMiquel Raynal
commit 69c7f4618c16b4678f8a4949b6bb5ace259c0033 upstream. Any write with either dd or flashcp to a device driven by the spear_smi.c driver will pass through the spear_smi_cpy_toio() function. This function will get called for chunks of up to 256 bytes. If the amount of data is smaller, we may have a problem if the data length is not 4-byte aligned. In this situation, the kernel panics during the memcpy: # dd if=/dev/urandom bs=1001 count=1 of=/dev/mtd6 spear_smi_cpy_toio [620] dest c9070000, src c7be8800, len 256 spear_smi_cpy_toio [620] dest c9070100, src c7be8900, len 256 spear_smi_cpy_toio [620] dest c9070200, src c7be8a00, len 256 spear_smi_cpy_toio [620] dest c9070300, src c7be8b00, len 233 Unhandled fault: external abort on non-linefetch (0x808) at 0xc90703e8 [...] PC is at memcpy+0xcc/0x330 The above error occurs because the implementation of memcpy_toio() tries to optimize the number of I/O by writing 4 bytes at a time as much as possible, until there are less than 4 bytes left and then switches to word or byte writes. Unfortunately, the specification states about the Write Burst mode: "the next AHB Write request should point to the next incremented address and should have the same size (byte, half-word or word)" This means ARM architecture implementation of memcpy_toio() cannot reliably be used blindly here. Workaround this situation by update the write path to stick to byte access when the burst length is not multiple of 4. Fixes: f18dbbb1bfe0 ("mtd: ST SPEAr: Add SMI driver for serial NOR flash") Cc: Russell King <linux@armlinux.org.uk> Cc: Boris Brezillon <boris.brezillon@collabora.com> Cc: stable@vger.kernel.org Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17tpm: add check after commands attribs tab allocationTadeusz Struk
commit f1689114acc5e89a196fec6d732dae3e48edb6ad upstream. devm_kcalloc() can fail and return NULL so we need to check for that. Cc: stable@vger.kernel.org Fixes: 58472f5cd4f6f ("tpm: validate TPM 2.0 commands") Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17usb: mon: Fix a deadlock in usbmon between mmap and readPete Zaitcev
commit 19e6317d24c25ee737c65d1ffb7483bdda4bb54a upstream. The problem arises because our read() function grabs a lock of the circular buffer, finds something of interest, then invokes copy_to_user() straight from the buffer, which in turn takes mm->mmap_sem. In the same time, the callback mon_bin_vma_fault() is invoked under mm->mmap_sem. It attempts to take the fetch lock and deadlocks. This patch does away with protecting of our page list with any semaphores, and instead relies on the kernel not close the device while mmap is active in a process. In addition, we prohibit re-sizing of a buffer while mmap is active. This way, when (now unlocked) fault is processed, it works with the page that is intended to be mapped-in, and not some other random page. Note that this may have an ABI impact, but hopefully no legitimate program is this wrong. Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Reported-by: syzbot+56f9673bb4cdcbeb0e92@syzkaller.appspotmail.com Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Fixes: 46eb14a6e158 ("USB: fix usbmon BUG trigger") Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191204203941.3503452b@suzdal.zaitcev.lan Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17usb: core: urb: fix URB structure initialization functionEmiliano Ingrassia
commit 1cd17f7f0def31e3695501c4f86cd3faf8489840 upstream. Explicitly initialize URB structure urb_list field in usb_init_urb(). This field can be potentially accessed uninitialized and its initialization is coherent with the usage of list_del_init() in usb_hcd_unlink_urb_from_ep() and usb_giveback_urb_bh() and its explicit initialization in usb_hcd_submit_urb() error path. Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191127160355.GA27196@ingrassia.epigenesys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17USB: adutux: fix interface sanity checkJohan Hovold
commit 3c11c4bed02b202e278c0f5c319ae435d7fb9815 upstream. Make sure to use the current alternate setting when verifying the interface descriptors to avoid binding to an invalid interface. Failing to do so could cause the driver to misbehave or trigger a WARN() in usb_submit_urb() that kernels with panic_on_warn set would choke on. Fixes: 03270634e242 ("USB: Add ADU support for Ontrak ADU devices") Cc: stable <stable@vger.kernel.org> # 2.6.19 Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191210112601.3561-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17USB: serial: io_edgeport: fix epic endpoint lookupJohan Hovold
commit 7c5a2df3367a2c4984f1300261345817d95b71f8 upstream. Make sure to use the current alternate setting when looking up the endpoints on epic devices to avoid binding to an invalid interface. Failing to do so could cause the driver to misbehave or trigger a WARN() in usb_submit_urb() that kernels with panic_on_warn set would choke on. Fixes: 6e8cf7751f9f ("USB: add EPIC support to the io_edgeport driver") Cc: stable <stable@vger.kernel.org> # 2.6.21 Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191210112601.3561-5-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17USB: idmouse: fix interface sanity checksJohan Hovold
commit 59920635b89d74b9207ea803d5e91498d39e8b69 upstream. Make sure to use the current alternate setting when verifying the interface descriptors to avoid binding to an invalid interface. Failing to do so could cause the driver to misbehave or trigger a WARN() in usb_submit_urb() that kernels with panic_on_warn set would choke on. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191210112601.3561-4-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17USB: atm: ueagle-atm: add missing endpoint checkJohan Hovold
commit 09068c1ad53fb077bdac288869dec2435420bdc4 upstream. Make sure that the interrupt interface has an endpoint before trying to access its endpoint descriptors to avoid dereferencing a NULL pointer. The driver binds to the interrupt interface with interface number 0, but must not assume that this interface or its current alternate setting are the first entries in the corresponding configuration arrays. Fixes: b72458a80c75 ("[PATCH] USB: Eagle and ADI 930 usb adsl modem driver") Cc: stable <stable@vger.kernel.org> # 2.6.16 Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191210112601.3561-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reportingChris Lesiak
commit 342a6928bd5017edbdae376042d8ad6af3d3b943 upstream. The IIO_HUMIDITYRELATIVE channel was being incorrectly reported back as percent when it should have been milli percent. This is via an incorrect scale value being returned to userspace. Signed-off-by: Chris Lesiak <chris.lesiak@licor.com> Acked-by: Matt Ranostay <matt.ranostay@konsulko.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17ARM: dts: pandora-common: define wl1251 as child node of mmc3H. Nikolaus Schaller
commit 4f9007d692017cef38baf2a9b82b7879d5b2407b upstream. Since v4.7 the dma initialization requires that there is a device tree property for "rx" and "tx" channels which is not provided by the pdata-quirks initialization. By conversion of the mmc3 setup to device tree this will finally allows to remove the OpenPandora wlan specific omap3 data-quirks. Fixes: 81eef6ca9201 ("mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Cc: <stable@vger.kernel.org> # v4.7+ Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17xhci: handle some XHCI_TRUST_TX_LENGTH quirks cases as default behaviour.Mathias Nyman
commit 7ff11162808cc2ec66353fc012c58bb449c892c3 upstream. xhci driver claims it needs XHCI_TRUST_TX_LENGTH quirk for both Broadcom/Cavium and a Renesas xHC controllers. The quirk was inteded for handling false "success" complete event for transfers that had data left untransferred. These transfers should complete with "short packet" events instead. In these two new cases the false "success" completion is reported after a "short packet" if the TD consists of several TRBs. xHCI specs 4.10.1.1.2 say remaining TRBs should report "short packet" as well after the first short packet in a TD, but this issue seems so common it doesn't make sense to add the quirk for all vendors. Turn these events into short packets automatically instead. This gets rid of the "The WARN Successful completion on short TX for slot 1 ep 1: needs XHCI_TRUST_TX_LENGTH quirk" warning in many cases. Cc: <stable@vger.kernel.org> Reported-by: Eli Billauer <eli.billauer@gmail.com> Reported-by: Ard Biesheuvel <ardb@kernel.org> Tested-by: Eli Billauer <eli.billauer@gmail.com> Tested-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20191211142007.8847-6-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17xhci: Increase STS_HALT timeout in xhci_suspend()Kai-Heng Feng
commit 7c67cf6658cec70d8a43229f2ce74ca1443dc95e upstream. I've recently observed failed xHCI suspend attempt on AMD Raven Ridge system: kernel: xhci_hcd 0000:04:00.4: WARN: xHC CMD_RUN timeout kernel: PM: suspend_common(): xhci_pci_suspend+0x0/0xd0 returns -110 kernel: PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -110 kernel: PM: dpm_run_callback(): pci_pm_suspend+0x0/0x150 returns -110 kernel: PM: Device 0000:04:00.4 failed to suspend async: error -110 Similar to commit ac343366846a ("xhci: Increase STS_SAVE timeout in xhci_suspend()") we also need to increase the HALT timeout to make it be able to suspend again. Cc: <stable@vger.kernel.org> # 5.2+ Fixes: f7fac17ca925 ("xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()") Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20191211142007.8847-5-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17usb: xhci: only set D3hot for pci deviceHenry Lin
commit f2c710f7dca8457e88b4ac9de2060f011254f9dd upstream. Xhci driver cannot call pci_set_power_state() on non-pci xhci host controllers. For example, NVIDIA Tegra XHCI host controller which acts as platform device with XHCI_SPURIOUS_WAKEUP quirk set in some platform hits this issue during shutdown. Cc: <stable@vger.kernel.org> Fixes: 638298dc66ea ("xhci: Fix spurious wakeups after S5 on Haswell") Signed-off-by: Henry Lin <henryl@nvidia.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20191211142007.8847-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17staging: gigaset: add endpoint-type sanity checkJohan Hovold
commit ed9ed5a89acba51b82bdff61144d4e4a4245ec8a upstream. Add missing endpoint-type sanity checks to probe. This specifically prevents a warning in USB core on URB submission when fuzzing USB descriptors. Signed-off-by: Johan Hovold <johan@kernel.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191202085610.12719-4-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17staging: gigaset: fix illegal free on probe errorsJohan Hovold
commit 84f60ca7b326ed8c08582417493982fe2573a9ad upstream. The driver failed to initialise its receive-buffer pointer, something which could lead to an illegal free on late probe errors. Fix this by making sure to clear all driver data at allocation. Fixes: 2032e2c2309d ("usb_gigaset: code cleanup") Cc: stable <stable@vger.kernel.org> # 2.6.33 Cc: Tilman Schmidt <tilman@imap.cc> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191202085610.12719-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17staging: gigaset: fix general protection fault on probeJohan Hovold
commit 53f35a39c3860baac1e5ca80bf052751cfb24a99 upstream. Fix a general protection fault when accessing the endpoint descriptors which could be triggered by a malicious device due to missing sanity checks on the number of endpoints. Reported-by: syzbot+35b1c403a14f5c89eba7@syzkaller.appspotmail.com Fixes: 07dc1f9f2f80 ("[PATCH] isdn4linux: Siemens Gigaset drivers - M105 USB DECT adapter") Cc: stable <stable@vger.kernel.org> # 2.6.17 Cc: Hansjoerg Lipp <hjlipp@web.de> Cc: Tilman Schmidt <tilman@imap.cc> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191202085610.12719-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17staging: rtl8712: fix interface sanity checkJohan Hovold
commit c724f776f048538ecfdf53a52b7a522309f5c504 upstream. Make sure to use the current alternate setting when verifying the interface descriptors to avoid binding to an invalid interface. Failing to do so could cause the driver to misbehave or trigger a WARN() in usb_submit_urb() that kernels with panic_on_warn set would choke on. Fixes: 2865d42c78a9 ("staging: r8712u: Add the new driver to the mainline kernel") Cc: stable <stable@vger.kernel.org> # 2.6.37 Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191210114751.5119-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17staging: rtl8188eu: fix interface sanity checkJohan Hovold
commit 74ca34118a0e05793935d804ccffcedd6eb56596 upstream. Make sure to use the current alternate setting when verifying the interface descriptors to avoid binding to an invalid interface. Failing to do so could cause the driver to misbehave or trigger a WARN() in usb_submit_urb() that kernels with panic_on_warn set would choke on. Fixes: c2478d39076b ("staging: r8188eu: Add files for new driver - part 20") Cc: stable <stable@vger.kernel.org> # 3.12 Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191210114751.5119-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17usb: Allow USB device to be warm reset in suspended stateKai-Heng Feng
commit e76b3bf7654c3c94554c24ba15a3d105f4006c80 upstream. On Dell WD15 dock, sometimes USB ethernet cannot be detected after plugging cable to the ethernet port, the hub and roothub get runtime resumed and runtime suspended immediately: ... [ 433.315169] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0 [ 433.315204] usb usb4: usb auto-resume [ 433.315226] hub 4-0:1.0: hub_resume [ 433.315239] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10202e2, return 0x10343 [ 433.315264] usb usb4-port1: status 0343 change 0001 [ 433.315279] xhci_hcd 0000:3a:00.0: clear port1 connect change, portsc: 0x10002e2 [ 433.315293] xhci_hcd 0000:3a:00.0: Get port status 4-2 read: 0x2a0, return 0x2a0 [ 433.317012] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.422282] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343 [ 433.422307] usb usb4-port1: do warm reset [ 433.422311] usb 4-1: device reset not allowed in state 8 [ 433.422339] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000 [ 433.422346] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343 [ 433.422356] usb usb4-port1: do warm reset [ 433.422358] usb 4-1: device reset not allowed in state 8 [ 433.422428] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 0 status = 0xf0002e2 [ 433.422455] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 1 status = 0xe0002a0 [ 433.422465] hub 4-0:1.0: hub_suspend [ 433.422475] usb usb4: bus auto-suspend, wakeup 1 [ 433.426161] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.466209] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.510204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.554051] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.598235] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.642154] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.686204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.730205] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.774203] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.818207] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.862040] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting [ 433.862053] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.862077] xhci_hcd 0000:3a:00.0: xhci_suspend: stopping port polling. [ 433.862096] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001 [ 433.862312] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_suspend: 0 [ 433.862445] xhci_hcd 0000:3a:00.0: PME# enabled [ 433.902376] xhci_hcd 0000:3a:00.0: restoring config space at offset 0xc (was 0x0, writing 0x20) [ 433.902395] xhci_hcd 0000:3a:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100403) [ 433.902490] xhci_hcd 0000:3a:00.0: PME# disabled [ 433.902504] xhci_hcd 0000:3a:00.0: enabling bus mastering [ 433.902547] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001 [ 433.902649] pcieport 0000:00:1b.0: PME: Spurious native interrupt! [ 433.902839] xhci_hcd 0000:3a:00.0: Port change event, 4-1, id 3, portsc: 0xb0202e2 [ 433.902842] xhci_hcd 0000:3a:00.0: resume root hub [ 433.902845] xhci_hcd 0000:3a:00.0: handle_port_status: starting port polling. [ 433.902877] xhci_hcd 0000:3a:00.0: xhci_resume: starting port polling. [ 433.902889] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling. [ 433.902891] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0 [ 433.902919] usb usb4: usb wakeup-resume [ 433.902942] usb usb4: usb auto-resume [ 433.902966] hub 4-0:1.0: hub_resume ... As Mathias pointed out, the hub enters Cold Attach Status state and requires a warm reset. However usb_reset_device() bails out early when the device is in suspended state, as its callers port_event() and hub_event() don't always resume the device. Since there's nothing wrong to reset a suspended device, allow usb_reset_device() to do so to solve the issue. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191106062710.29880-1-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17USB: documentation: flags on usb-storage versus UASOliver Neukum
commit 65cc8bf99349f651a0a2cee69333525fe581f306 upstream. Document which flags work storage, UAS or both Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191114112758.32747-4-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17USB: uas: heed CAPACITY_HEURISTICSOliver Neukum
commit 335cbbd5762d5e5c67a8ddd6e6362c2aa42a328f upstream. There is no need to ignore this flag. We should be as close to storage in that regard as makes sense, so honor flags whose cost is tiny. Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191114112758.32747-3-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17USB: uas: honor flag to avoid CAPACITY16Oliver Neukum
commit bff000cae1eec750d62e265c4ba2db9af57b17e1 upstream. Copy the support over from usb-storage to get feature parity Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191114112758.32747-2-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17media: venus: remove invalid compat_ioctl32 handlerArnd Bergmann
commit 4adc0423de92cf850d1ef5c0e7cb28fd7a38219e upstream. v4l2_compat_ioctl32() is the function that calls into v4l2_file_operations->compat_ioctl32(), so setting that back to the same function leads to a trivial endless loop, followed by a kernel stack overrun. Remove the incorrect assignment. Cc: stable@vger.kernel.org Fixes: 7472c1c69138 ("[media] media: venus: vdec: add video decoder files") Fixes: aaaa93eda64b ("[media] media: venus: venc: add video encoder files") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17scsi: qla2xxx: Fix driver unload hangQuinn Tran
commit dd322b7f3efc8cda085bb60eadc4aee6324eadd8 upstream. This patch fixes driver unload hang by removing msleep() Fixes: d74595278f4ab ("scsi: qla2xxx: Add multiple queue pair functionality.") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191105150657.8092-5-hmadhani@marvell.com Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17usb: gadget: pch_udc: fix use after freeGustavo A. R. Silva
commit 66d1b0c0580b7f1b1850ee4423f32ac42afa2e92 upstream. Remove pointer dereference after free. pci_pool_free doesn't care about contents of td. It's just a void* for it Addresses-Coverity-ID: 1091173 ("Use after free") Cc: stable@vger.kernel.org Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Link: https://lore.kernel.org/r/20191106202821.GA20347@embeddedor Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17usb: gadget: configfs: Fix missing spin_lock_init()Wei Yongjun
commit 093edc2baad2c258b1f55d1ab9c63c2b5ae67e42 upstream. The driver allocates the spinlock but not initialize it. Use spin_lock_init() on it to initialize it correctly. This is detected by Coccinelle semantic patch. Fixes: 1a1c851bbd70 ("usb: gadget: configfs: fix concurrent issue between composite APIs") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Cc: stable <stable@vger.kernel.org> Reviewed-by: Peter Chen <peter.chen@nxp.com> Link: https://lore.kernel.org/r/20191030034046.188808-1-weiyongjun1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17appletalk: Set error code if register_snap_client failedYueHaibing
commit c93ad1337ad06a718890a89cdd85188ff9a5a5cc upstream. If register_snap_client fails in atalk_init, error code should be set, otherwise it will triggers NULL pointer dereference while unloading module. Fixes: 9804501fa122 ("appletalk: Fix potential NULL pointer dereference in unregister_snap_client") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17appletalk: Fix potential NULL pointer dereference in unregister_snap_clientYueHaibing
commit 9804501fa1228048857910a6bf23e085aade37cc upstream. register_snap_client may return NULL, all the callers check it, but only print a warning. This will result in NULL pointer dereference in unregister_snap_client and other places. It has always been used like this since v2.6 Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> [bwh: Backported to <4.15: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17KVM: x86: fix out-of-bounds write in KVM_GET_EMULATED_CPUID (CVE-2019-19332)Paolo Bonzini
commit 433f4ba1904100da65a311033f17a9bf586b287e upstream. The bounds check was present in KVM_GET_SUPPORTED_CPUID but not KVM_GET_EMULATED_CPUID. Reported-by: syzbot+e3f4897236c4eeb8af4f@syzkaller.appspotmail.com Fixes: 84cffe499b94 ("kvm: Emulate MOVBE", 2013-10-29) Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17ASoC: rsnd: fixup MIX kctrl registrationKuninori Morimoto
commit 7aea8a9d71d54f449f49e20324df06341cc18395 upstream. Renesas sound device has many IPs and many situations. If platform/board uses MIXer, situation will be more complex. To avoid duplicate DVC kctrl registration when MIXer was used, it had original flags. But it was issue when sound card was re-binded, because no one can't cleanup this flags then. To solve this issue, commit 9c698e8481a15237a ("ASoC: rsnd: tidyup registering method for rsnd_kctrl_new()") checks registered card->controls, because if card was re-binded, these were cleanuped automatically. This patch could solve re-binding issue. But, it start to avoid MIX kctrl. To solve these issues, we need below. To avoid card re-binding issue: check registered card->controls To avoid duplicate DVC registration: check registered rsnd_kctrl_cfg To allow multiple MIX registration: check registered rsnd_kctrl_cfg This patch do it. Fixes: 9c698e8481a15237a ("ASoC: rsnd: tidyup registering method for rsnd_kctrl_new()") Reported-by: Jiada Wang <jiada_wang@mentor.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-By: Jiada Wang <jiada_wang@mentor.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17binder: Handle start==NULL in binder_update_page_range()Jann Horn
commit 2a9edd056ed4fbf9d2e797c3fc06335af35bccc4 upstream. The old loop wouldn't stop when reaching `start` if `start==NULL`, instead continuing backwards to index -1 and crashing. Luckily you need to be highly privileged to map things at NULL, so it's not a big problem. Fix it by adjusting the loop so that the loop variable is always in bounds. This patch is deliberately minimal to simplify backporting, but IMO this function could use a refactor. The jump labels in the second loop body are horrible (the error gotos should be jumping to free_range instead), and both loops would look nicer if they just iterated upwards through indices. And the up_read()+mmput() shouldn't be duplicated like that. Cc: stable@vger.kernel.org Fixes: 457b9a6f09f0 ("Staging: android: add binder driver") Signed-off-by: Jann Horn <jannh@google.com> Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Link: https://lore.kernel.org/r/20191018205631.248274-3-jannh@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17thermal: Fix deadlock in thermal thermal_zone_device_checkWei Wang
commit 163b00cde7cf2206e248789d2780121ad5e6a70b upstream. 1851799e1d29 ("thermal: Fix use-after-free when unregistering thermal zone device") changed cancel_delayed_work to cancel_delayed_work_sync to avoid a use-after-free issue. However, cancel_delayed_work_sync could be called insides the WQ causing deadlock. [54109.642398] c0 1162 kworker/u17:1 D 0 11030 2 0x00000000 [54109.642437] c0 1162 Workqueue: thermal_passive_wq thermal_zone_device_check [54109.642447] c0 1162 Call trace: [54109.642456] c0 1162 __switch_to+0x138/0x158 [54109.642467] c0 1162 __schedule+0xba4/0x1434 [54109.642480] c0 1162 schedule_timeout+0xa0/0xb28 [54109.642492] c0 1162 wait_for_common+0x138/0x2e8 [54109.642511] c0 1162 flush_work+0x348/0x40c [54109.642522] c0 1162 __cancel_work_timer+0x180/0x218 [54109.642544] c0 1162 handle_thermal_trip+0x2c4/0x5a4 [54109.642553] c0 1162 thermal_zone_device_update+0x1b4/0x25c [54109.642563] c0 1162 thermal_zone_device_check+0x18/0x24 [54109.642574] c0 1162 process_one_work+0x3cc/0x69c [54109.642583] c0 1162 worker_thread+0x49c/0x7c0 [54109.642593] c0 1162 kthread+0x17c/0x1b0 [54109.642602] c0 1162 ret_from_fork+0x10/0x18 [54109.643051] c0 1162 kworker/u17:2 D 0 16245 2 0x00000000 [54109.643067] c0 1162 Workqueue: thermal_passive_wq thermal_zone_device_check [54109.643077] c0 1162 Call trace: [54109.643085] c0 1162 __switch_to+0x138/0x158 [54109.643095] c0 1162 __schedule+0xba4/0x1434 [54109.643104] c0 1162 schedule_timeout+0xa0/0xb28 [54109.643114] c0 1162 wait_for_common+0x138/0x2e8 [54109.643122] c0 1162 flush_work+0x348/0x40c [54109.643131] c0 1162 __cancel_work_timer+0x180/0x218 [54109.643141] c0 1162 handle_thermal_trip+0x2c4/0x5a4 [54109.643150] c0 1162 thermal_zone_device_update+0x1b4/0x25c [54109.643159] c0 1162 thermal_zone_device_check+0x18/0x24 [54109.643167] c0 1162 process_one_work+0x3cc/0x69c [54109.643177] c0 1162 worker_thread+0x49c/0x7c0 [54109.643186] c0 1162 kthread+0x17c/0x1b0 [54109.643195] c0 1162 ret_from_fork+0x10/0x18 [54109.644500] c0 1162 cat D 0 7766 1 0x00000001 [54109.644515] c0 1162 Call trace: [54109.644524] c0 1162 __switch_to+0x138/0x158 [54109.644536] c0 1162 __schedule+0xba4/0x1434 [54109.644546] c0 1162 schedule_preempt_disabled+0x80/0xb0 [54109.644555] c0 1162 __mutex_lock+0x3a8/0x7f0 [54109.644563] c0 1162 __mutex_lock_slowpath+0x14/0x20 [54109.644575] c0 1162 thermal_zone_get_temp+0x84/0x360 [54109.644586] c0 1162 temp_show+0x30/0x78 [54109.644609] c0 1162 dev_attr_show+0x5c/0xf0 [54109.644628] c0 1162 sysfs_kf_seq_show+0xcc/0x1a4 [54109.644636] c0 1162 kernfs_seq_show+0x48/0x88 [54109.644656] c0 1162 seq_read+0x1f4/0x73c [54109.644664] c0 1162 kernfs_fop_read+0x84/0x318 [54109.644683] c0 1162 __vfs_read+0x50/0x1bc [54109.644692] c0 1162 vfs_read+0xa4/0x140 [54109.644701] c0 1162 SyS_read+0xbc/0x144 [54109.644708] c0 1162 el0_svc_naked+0x34/0x38 [54109.845800] c0 1162 D 720.000s 1->7766->7766 cat [panic] Fixes: 1851799e1d29 ("thermal: Fix use-after-free when unregistering thermal zone device") Cc: stable@vger.kernel.org Signed-off-by: Wei Wang <wvw@google.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17iomap: Fix pipe page leakage during splicingJan Kara
commit 419e9c38aa075ed0cd3c13d47e15954b686bcdb6 upstream. When splicing using iomap_dio_rw() to a pipe, we may leak pipe pages because bio_iov_iter_get_pages() records that the pipe will have full extent worth of data however if file size is not block size aligned iomap_dio_rw() returns less than what bio_iov_iter_get_pages() set up and splice code gets confused leaking a pipe page with the file tail. Handle the situation similarly to the old direct IO implementation and revert iter to actually returned read amount which makes iter consistent with value returned from iomap_dio_rw() and thus the splice code is happy. Fixes: ff6a9292e6f6 ("iomap: implement direct I/O") CC: stable@vger.kernel.org Reported-by: syzbot+991400e8eba7e00a26e1@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17RDMA/qib: Validate ->show()/store() callbacks before calling themViresh Kumar
commit 7ee23491b39259ae83899dd93b2a29ef0f22f0a7 upstream. The permissions of the read-only or write-only sysfs files can be changed (as root) and the user can then try to read a write-only file or write to a read-only file which will lead to kernel crash here. Protect against that by always validating the show/store callbacks. Link: https://lore.kernel.org/r/d45cc26361a174ae12dbb86c994ef334d257924b.1573096807.git.viresh.kumar@linaro.org Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17spi: atmel: Fix CS high supportGregory CLEMENT
commit 7cbb16b2122c09f2ae393a1542fed628505b9da6 upstream. Until a few years ago, this driver was only used with CS GPIO. The only exception is CS0 on AT91RM9200 which has to use internal CS. A limitation of the internal CS is that they don't support CS High. So by using the CS GPIO the CS high configuration was available except for the particular case CS0 on RM9200. When the support for the internal chip-select was added, the check of the CS high support was not updated. Due to this the driver accepts this configuration for all the SPI controller v2 (used by all SoCs excepting the AT91RM9200) whereas the hardware doesn't support it for infernal CS. This patch fixes the test to match the hardware capabilities. Fixes: 4820303480a1 ("spi: atmel: add support for the internal chip-select of the spi controller") Cc: <stable@vger.kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Link: https://lore.kernel.org/r/20191017141846.7523-3-gregory.clement@bootlin.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17crypto: user - fix memory leak in crypto_reportNavid Emamdoost
commit ffdde5932042600c6807d46c1550b28b0db6a3bc upstream. In crypto_report, a new skb is created via nlmsg_new(). This skb should be released if crypto_report_alg() fails. Fixes: a38f7907b926 ("crypto: Add userspace configuration API") Cc: <stable@vger.kernel.org> Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17crypto: ecdh - fix big endian bug in ECC libraryArd Biesheuvel
commit f398243e9fd6a3a059c1ea7b380c40628dbf0c61 upstream. The elliptic curve arithmetic library used by the EC-DH KPP implementation assumes big endian byte order, and unconditionally reverses the byte and word order of multi-limb quantities. On big endian systems, the byte reordering is not necessary, while the word ordering needs to be retained. So replace the __swab64() invocation with a call to be64_to_cpu() which should do the right thing for both little and big endian builds. Fixes: 3c4b23901a0c ("crypto: ecdh - Add ECDH software support") Cc: <stable@vger.kernel.org> # v4.9+ Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17crypto: ccp - fix uninitialized list headMark Salter
commit 691505a803a7f223b2af621848d581259c61f77d upstream. A NULL-pointer dereference was reported in fedora bz#1762199 while reshaping a raid6 array after adding a fifth drive to an existing array. [ 47.343549] md/raid:md0: raid level 6 active with 3 out of 5 devices, algorithm 2 [ 47.804017] md0: detected capacity change from 0 to 7885289422848 [ 47.822083] Unable to handle kernel read from unreadable memory at virtual address 0000000000000000 ... [ 47.940477] CPU: 1 PID: 14210 Comm: md0_raid6 Tainted: G W 5.2.18-200.fc30.aarch64 #1 [ 47.949594] Hardware name: AMD Overdrive/Supercharger/To be filled by O.E.M., BIOS ROD1002C 04/08/2016 [ 47.958886] pstate: 00400085 (nzcv daIf +PAN -UAO) [ 47.963668] pc : __list_del_entry_valid+0x2c/0xa8 [ 47.968366] lr : ccp_tx_submit+0x84/0x168 [ccp] [ 47.972882] sp : ffff00001369b970 [ 47.976184] x29: ffff00001369b970 x28: ffff00001369bdb8 [ 47.981483] x27: 00000000ffffffff x26: ffff8003b758af70 [ 47.986782] x25: ffff8003b758b2d8 x24: ffff8003e6245818 [ 47.992080] x23: 0000000000000000 x22: ffff8003e62450c0 [ 47.997379] x21: ffff8003dfd6add8 x20: 0000000000000003 [ 48.002678] x19: ffff8003e6245100 x18: 0000000000000000 [ 48.007976] x17: 0000000000000000 x16: 0000000000000000 [ 48.013274] x15: 0000000000000000 x14: 0000000000000000 [ 48.018572] x13: ffff7e000ef83a00 x12: 0000000000000001 [ 48.023870] x11: ffff000010eff998 x10: 00000000000019a0 [ 48.029169] x9 : 0000000000000000 x8 : ffff8003e6245180 [ 48.034467] x7 : 0000000000000000 x6 : 000000000000003f [ 48.039766] x5 : 0000000000000040 x4 : ffff8003e0145080 [ 48.045064] x3 : dead000000000200 x2 : 0000000000000000 [ 48.050362] x1 : 0000000000000000 x0 : ffff8003e62450c0 [ 48.055660] Call trace: [ 48.058095] __list_del_entry_valid+0x2c/0xa8 [ 48.062442] ccp_tx_submit+0x84/0x168 [ccp] [ 48.066615] async_tx_submit+0x224/0x368 [async_tx] [ 48.071480] async_trigger_callback+0x68/0xfc [async_tx] [ 48.076784] ops_run_biofill+0x178/0x1e8 [raid456] [ 48.081566] raid_run_ops+0x248/0x818 [raid456] [ 48.086086] handle_stripe+0x864/0x1208 [raid456] [ 48.090781] handle_active_stripes.isra.0+0xb0/0x278 [raid456] [ 48.096604] raid5d+0x378/0x618 [raid456] [ 48.100602] md_thread+0xa0/0x150 [ 48.103905] kthread+0x104/0x130 [ 48.107122] ret_from_fork+0x10/0x18 [ 48.110686] Code: d2804003 f2fbd5a3 eb03003f 54000320 (f9400021) [ 48.116766] ---[ end trace 23f390a527f7ad77 ]--- ccp_tx_submit is passed a dma_async_tx_descriptor which is contained in a ccp_dma_desc and adds it to a ccp channel's pending list: list_del(&desc->entry); list_add_tail(&desc->entry, &chan->pending); The problem is that desc->entry may be uninitialized in the async_trigger_callback path where the descriptor was gotten from ccp_prep_dma_interrupt which got it from ccp_alloc_dma_desc which doesn't initialize the desc->entry list head. So, just initialize the list head to avoid the problem. Cc: <stable@vger.kernel.org> Reported-by: Sahaj Sarup <sahajsarup@gmail.com> Signed-off-by: Mark Salter <msalter@redhat.com> Acked-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17crypto: af_alg - cast ki_complete ternary op to intAyush Sawal
commit 64e7f852c47ce99f6c324c46d6a299a5a7ebead9 upstream. when libkcapi test is executed using HW accelerator, cipher operation return -74.Since af_alg_async_cb->ki_complete treat err as unsigned int, libkcapi receive 429467222 even though it expect -ve value. Hence its required to cast resultlen to int so that proper error is returned to libkcapi. AEAD one shot non-aligned test 2(libkcapi test) ./../bin/kcapi -x 10 -c "gcm(aes)" -i 7815d4b06ae50c9c56e87bd7 -k ea38ac0c9b9998c80e28fb496a2b88d9 -a "853f98a750098bec1aa7497e979e78098155c877879556bb51ddeb6374cbaefc" -t "c4ce58985b7203094be1d134c1b8ab0b" -q "b03692f86d1b8b39baf2abb255197c98" Fixes: d887c52d6ae4 ("crypto: algif_aead - overhaul memory management") Cc: <stable@vger.kernel.org> Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com> Signed-off-by: Atul Gupta <atul.gupta@chelsio.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17crypto: crypto4xx - fix double-free in crypto4xx_destroy_sdrChristian Lamparter
commit 746c908c4d72e49068ab216c3926d2720d71a90d upstream. This patch fixes a crash that can happen during probe when the available dma memory is not enough (this can happen if the crypto4xx is built as a module). The descriptor window mapping would end up being free'd twice, once in crypto4xx_build_pdr() and the second time in crypto4xx_destroy_sdr(). Fixes: 5d59ad6eea82 ("crypto: crypto4xx - fix crypto4xx_build_pdr, crypto4xx_build_sdr leak") Cc: <stable@vger.kernel.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17KVM: x86: fix presentation of TSX feature in ARCH_CAPABILITIESPaolo Bonzini
commit cbbaa2727aa3ae9e0a844803da7cef7fd3b94f2b upstream. KVM does not implement MSR_IA32_TSX_CTRL, so it must not be presented to the guests. It is also confusing to have !ARCH_CAP_TSX_CTRL_MSR && !RTM && ARCH_CAP_TAA_NO: lack of MSR_IA32_TSX_CTRL suggests TSX was not hidden (it actually was), yet the value says that TSX is not vulnerable to microarchitectural data sampling. Fix both. Cc: stable@vger.kernel.org Tested-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17KVM: x86: do not modify masked bits of shared MSRsPaolo Bonzini
commit de1fca5d6e0105c9d33924e1247e2f386efc3ece upstream. "Shared MSRs" are guest MSRs that are written to the host MSRs but keep their value until the next return to userspace. They support a mask, so that some bits keep the host value, but this mask is only used to skip an unnecessary MSR write and the value written to the MSR is always the guest MSR. Fix this and, while at it, do not update smsr->values[slot].curr if for whatever reason the wrmsr fails. This should only happen due to reserved bits, so the value written to smsr->values[slot].curr will not match when the user-return notifier and the host value will always be restored. However, it is untidy and in rare cases this can actually avoid spurious WRMSRs on return to userspace. Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Tested-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17KVM: arm/arm64: vgic: Don't rely on the wrong pending tableZenghui Yu
commit ca185b260951d3b55108c0b95e188682d8a507b7 upstream. It's possible that two LPIs locate in the same "byte_offset" but target two different vcpus, where their pending status are indicated by two different pending tables. In such a scenario, using last_byte_offset optimization will lead KVM relying on the wrong pending table entry. Let us use last_ptr instead, which can be treated as a byte index into a pending table and also, can be vcpu specific. Fixes: 280771252c1b ("KVM: arm64: vgic-v3: KVM_DEV_ARM_VGIC_SAVE_PENDING_TABLES") Cc: stable@vger.kernel.org Signed-off-by: Zenghui Yu <yuzenghui@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Acked-by: Eric Auger <eric.auger@redhat.com> Link: https://lore.kernel.org/r/20191029071919.177-4-yuzenghui@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17drm/i810: Prevent underflow in ioctlDan Carpenter
commit 4f69851fbaa26b155330be35ce8ac393e93e7442 upstream. The "used" variables here come from the user in the ioctl and it can be negative. It could result in an out of bounds write. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20191004102251.GC823@mwanda Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17jbd2: Fix possible overflow in jbd2_log_space_left()Jan Kara
commit add3efdd78b8a0478ce423bb9d4df6bd95e8b335 upstream. When number of free space in the journal is very low, the arithmetic in jbd2_log_space_left() could underflow resulting in very high number of free blocks and thus triggering assertion failure in transaction commit code complaining there's not enough space in the journal: J_ASSERT(journal->j_free > 1); Properly check for the low number of free blocks. CC: stable@vger.kernel.org Reviewed-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20191105164437.32602-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17kernfs: fix ino wrap-around detectionTejun Heo
commit e23f568aa63f64cd6b355094224cc9356c0f696b upstream. When the 32bit ino wraps around, kernfs increments the generation number to distinguish reused ino instances. The wrap-around detection tests whether the allocated ino is lower than what the cursor but the cursor is pointing to the next ino to allocate so the condition never triggers. Fix it by remembering the last ino and comparing against that. Signed-off-by: Tejun Heo <tj@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Fixes: 4a3ef68acacf ("kernfs: implement i_generation") Cc: Namhyung Kim <namhyung@kernel.org> Cc: stable@vger.kernel.org # v4.14+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17can: slcan: Fix use-after-free Read in slcan_openJouni Hogander
commit 9ebd796e24008f33f06ebea5a5e6aceb68b51794 upstream. Slcan_open doesn't clean-up device which registration failed from the slcan_devs device list. On next open this list is iterated and freed device is accessed. Fix this by calling slc_free_netdev in error path. Driver/net/can/slcan.c is derived from slip.c. Use-after-free error was identified in slip_open by syzboz. Same bug is in slcan.c. Here is the trace from the Syzbot slip report: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x197/0x210 lib/dump_stack.c:118 print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374 __kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506 kasan_report+0x12/0x20 mm/kasan/common.c:634 __asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132 sl_sync drivers/net/slip/slip.c:725 [inline] slip_open+0xecd/0x11b7 drivers/net/slip/slip.c:801 tty_ldisc_open.isra.0+0xa3/0x110 drivers/tty/tty_ldisc.c:469 tty_set_ldisc+0x30e/0x6b0 drivers/tty/tty_ldisc.c:596 tiocsetd drivers/tty/tty_io.c:2334 [inline] tty_ioctl+0xe8d/0x14f0 drivers/tty/tty_io.c:2594 vfs_ioctl fs/ioctl.c:46 [inline] file_ioctl fs/ioctl.c:509 [inline] do_vfs_ioctl+0xdb6/0x13e0 fs/ioctl.c:696 ksys_ioctl+0xab/0xd0 fs/ioctl.c:713 __do_sys_ioctl fs/ioctl.c:720 [inline] __se_sys_ioctl fs/ioctl.c:718 [inline] __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718 do_syscall_64+0xfa/0x760 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe Fixes: ed50e1600b44 ("slcan: Fix memory leak in error path") Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: David Miller <davem@davemloft.net> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com> Cc: linux-stable <stable@vger.kernel.org> # >= v5.4 Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17tty: vt: keyboard: reject invalid keycodesDmitry Torokhov
commit b2b2dd71e0859436d4e05b2f61f86140250ed3f8 upstream. Do not try to handle keycodes that are too big, otherwise we risk doing out-of-bounds writes: BUG: KASAN: global-out-of-bounds in clear_bit include/asm-generic/bitops-instrumented.h:56 [inline] BUG: KASAN: global-out-of-bounds in kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline] BUG: KASAN: global-out-of-bounds in kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495 Write of size 8 at addr ffffffff89a1b2d8 by task syz-executor108/1722 ... kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline] kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495 input_to_handler+0x3b6/0x4c0 drivers/input/input.c:118 input_pass_values.part.0+0x2e3/0x720 drivers/input/input.c:145 input_pass_values drivers/input/input.c:949 [inline] input_set_keycode+0x290/0x320 drivers/input/input.c:954 evdev_handle_set_keycode_v2+0xc4/0x120 drivers/input/evdev.c:882 evdev_do_ioctl drivers/input/evdev.c:1150 [inline] In this case we were dealing with a fuzzed HID device that declared over 12K buttons, and while HID layer should not be reporting to us such big keycodes, we should also be defensive and reject invalid data ourselves as well. Reported-by: syzbot+19340dff067c2d3835c0@syzkaller.appspotmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191122204220.GA129459@dtor-ws Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17CIFS: Fix SMB2 oplock break processingPavel Shilovsky
commit fa9c2362497fbd64788063288dc4e74daf977ebb upstream. Even when mounting modern protocol version the server may be configured without supporting SMB2.1 leases and the client uses SMB2 oplock to optimize IO performance through local caching. However there is a problem in oplock break handling that leads to missing a break notification on the client who has a file opened. It latter causes big latencies to other clients that are trying to open the same file. The problem reproduces when there are multiple shares from the same server mounted on the client. The processing code tries to match persistent and volatile file ids from the break notification with an open file but it skips all share besides the first one. Fix this by looking up in all shares belonging to the server that issued the oplock break. Cc: Stable <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-12-17CIFS: Fix NULL-pointer dereference in smb2_push_mandatory_locksPavel Shilovsky
commit 6f582b273ec23332074d970a7fb25bef835df71f upstream. Currently when the client creates a cifsFileInfo structure for a newly opened file, it allocates a list of byte-range locks with a pointer to the new cfile and attaches this list to the inode's lock list. The latter happens before initializing all other fields, e.g. cfile->tlink. Thus a partially initialized cifsFileInfo structure becomes available to other threads that walk through the inode's lock list. One example of such a thread may be an oplock break worker thread that tries to push all cached byte-range locks. This causes NULL-pointer dereference in smb2_push_mandatory_locks() when accessing cfile->tlink: [598428.945633] BUG: kernel NULL pointer dereference, address: 0000000000000038 ... [598428.945749] Workqueue: cifsoplockd cifs_oplock_break [cifs] [598428.945793] RIP: 0010:smb2_push_mandatory_locks+0xd6/0x5a0 [cifs] ... [598428.945834] Call Trace: [598428.945870] ? cifs_revalidate_mapping+0x45/0x90 [cifs] [598428.945901] cifs_oplock_break+0x13d/0x450 [cifs] [598428.945909] process_one_work+0x1db/0x380 [598428.945914] worker_thread+0x4d/0x400 [598428.945921] kthread+0x104/0x140 [598428.945925] ? process_one_work+0x380/0x380 [598428.945931] ? kthread_park+0x80/0x80 [598428.945937] ret_from_fork+0x35/0x40 Fix this by reordering initialization steps of the cifsFileInfo structure: initialize all the fields first and then add the new byte-range lock list to the inode's lock list. Cc: Stable <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-01 04:38:56 +0000