summaryrefslogtreecommitdiff
AgeCommit message (Expand)Author
2015-01-06arm: vf610-colibri-dual-eth: UART supportBhuvanchandra DV
2015-01-06ARM: imx: clk-vf610: Add clock for UART4 and UART5Bhuvanchandra DV
2015-01-06arm: vf610-colibri-dual-eth: Remove nodesBhuvanchandra DV
2014-11-20drivers/net/ethernet/freescale: fec_main: Fixed dual ethernet usageBhuvanchandra DV
2014-11-20ARM: dts: vf610: Add device trees for Dual Ethernet boardBhuvanchandra DV
2014-11-19Merge branch 'vf610-dcu-3.18-2' into toradex_vf_3.18-nextStefan Agner
2014-11-19Merge branch 'vf610-nfc-3.18' into toradex_vf_3.18-nextStefan Agner
2014-11-19ARM: colibri_vf61: enable fsl_nand driverStefan Agner
2014-11-19imx:vf610: Allow user to enable NAND controller for the VF610 SOC.Bill Pringlemeir
2014-11-19imx:vf610: Add device tree support for the fsl_nfc driver and NAND interface.Bill Pringlemeir
2014-11-19mtd:fsl_nfc: Add device tree documentation.Bill Pringlemeir
2014-11-19mtd:fsl_nfc: Add hardware 45 byte BHC-ECC support for 24 bit corrections.Bill Pringlemeir
2014-11-19mtd:fsl_nfc: Nand flash controller for VF610, MPC5125, etc.Bill Pringlemeir
2014-11-19dmaengine: fsl-edma: fix calculation of remaining bytesStefan Agner
2014-11-19ARM: dts: vf610-colibri: enable DCU framebufferStefan Agner
2014-11-19video: fsl-dcu-fb: add video= cmdline supportStefan Agner
2014-11-19video: fsl-dcu-fb: support signal polarity configurationStefan Agner
2014-11-19video: fsl-dcu-fb: use native-display timingStefan Agner
2014-11-19video: fsl-dcu-fb: use num_timings to iterate timingsStefan Agner
2014-11-19Documentation: DT: Add DCU framebuffer driverAlison Wang
2014-11-19fb: Add DCU framebuffer driver for Vybrid VF610 platformAlison Wang
2014-11-19ARM: clk: vf610: Add DCU and TCON clock supportAlison Wang
2014-11-19ARM: dts: vf610-twr: Enable DCU and TCON devicesAlison Wang
2014-11-19ARM: dts: vf610: Add DCU and TCON nodesAlison Wang
2014-11-19Merge branch 'vf610-adc-temperature' into toradex_vf_3.18-nextStefan Agner
2014-11-19drivers/iio/adc/vf610-adc: Add temperature sensor supportarchive/vf610-adc-temperatureSanchayan Maity
2014-11-19Merge branch 'vf610-snvs-rtc' into toradex_vf_3.18-nextStefan Agner
2014-11-19drivers/rtc/rtc-snvs: Add clock supportSanchayan Maity
2014-11-19ARM: dts: vfxxx: Add SNVS nodeSanchayan Maity
2014-11-19ARM: imx: clk-vf610: Add clock for SNVSSanchayan Maity
2014-11-19Merge branch 'vf610-gpio-v5-non-dts' into toradex_vf_3.18-nextStefan Agner
2014-11-19Merge branch 'imx/dt' into for-nextShawn Guo
2014-11-19Merge branch 'imx/soc' into for-nextShawn Guo
2014-11-19ARM: dts: imx6: add pm_power_off support for i.mx6 chipsimx-dt-3.19Robin Gong
2014-11-19ARM: dts: vf-colibri: add USB regulatorsStefan Agner
2014-11-19ARM: dts: imx6: phyFLEX: Add CAN supportChristian Hemp
2014-11-19ARM: dts: imx6: phyFLEX: Add PCIeChristian Hemp
2014-11-19ARM: dts: imx6: phyFLEX: Set correct interrupt for pmicChristian Hemp
2014-11-19ARM: dts: imx6: phyFLEX: Enable gpmi in module fileChristian Hemp
2014-11-19ARM: dts: imx6: phyFLEX: set nodes in alphabetical orderChristian Hemp
2014-11-19ARM: dts: vf-colibri-eval-v3.dts: Enable ST-M41T0M6 RTCBhuvanchandra DV
2014-11-19ARM: dts: vf-colibri: Add I2C supportBhuvanchandra DV
2014-11-19ARM: dts: imx6qdl: Enable CODA960 VPUPhilipp Zabel
2014-11-19ARM: dts: imx6q-tbs2910: Remove unneeded 'fsl,mode' propertyFabio Estevam
2014-11-19ARM: dts: vf610: enable USB misc/phy nodes where necessaryStefan Agner
2014-11-19ARM: dts: vf610: use new GPIO supportStefan Agner
2014-11-19ARM: dts: pbab01: enable I2S audio on phyFLEX-i.MX6 boardsDmitry Lavnikevich
2014-11-19ARM: dts: pbab01: move i2c pins and frequency configuration into pfla02Dmitry Lavnikevich
2014-11-19ARM: dts: vf500-colibri: add Colibri VF50 supportStefan Agner
2014-11-19ARM: dts: vf610: create generic base device treesStefan Agner
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-02 21:04:02 +0000