summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2015-05-06serial: 8250_dw: add support for AMD SOC CarrizoKen Xue
commit 5ef86b74209db33c133b5f18738dd8f3189b63a1 upstream. Add ACPI identifier for UART on AMD SOC Carrizo. Signed-off-by: Ken Xue <Ken.Xue@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06dm crypt: fix deadlock when async crypto algorithm returns -EBUSYBen Collins
commit 0618764cb25f6fa9fb31152995de42a8a0496475 upstream. I suspect this doesn't show up for most anyone because software algorithms typically don't have a sense of being too busy. However, when working with the Freescale CAAM driver it will return -EBUSY on occasion under heavy -- which resulted in dm-crypt deadlock. After checking the logic in some other drivers, the scheme for crypt_convert() and it's callback, kcryptd_async_done(), were not correctly laid out to properly handle -EBUSY or -EINPROGRESS. Fix this by using the completion for both -EBUSY and -EINPROGRESS. Now crypt_convert()'s use of completion is comparable to af_alg_wait_for_completion(). Similarly, kcryptd_async_done() follows the pattern used in af_alg_complete(). Before this fix dm-crypt would lockup within 1-2 minutes running with the CAAM driver. Fix was regression tested against software algorithms on PPC32 and x86_64, and things seem perfectly happy there as well. Signed-off-by: Ben Collins <ben.c@servergy.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06clk: qcom: Fix ipq806x LCC frequency tablesStephen Boyd
commit b3261d768bcdd4b368179ed85becf38c95461848 upstream. These frequency tables list the wrong rates. Either they don't have the correct frequency at all, or they're specified in kHz instead of Hz. Fix it. Fixes: c99e515a92e9 "clk: qcom: Add IPQ806X LPASS clock controller (LCC) driver" Tested-by: Kenneth Westfield <kwestfie@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06clk: qcom: fix RCG M/N counter configurationArchit Taneja
commit 0b21503dbbfa669dbd847b33578d4041513cddb2 upstream. Currently, a RCG's M/N counter (used for fraction division) is set to either 'bypass' (counter disabled) or 'dual edge' (counter enabled) based on whether the corresponding rcg struct has a mnd field specified and a non-zero N. In the case where M and N are the same value, the M/N counter is still enabled by code even though no division takes place. Leaving the RCG in such a state can result in improper behavior. This was observed with the DSI pixel clock RCG when M and N were both set to 1. Add an additional check (M != N) to enable the M/N counter only when it's needed for fraction division. Signed-off-by: Archit Taneja <architt@codeaurora.org> Fixes: bcd61c0f535a (clk: qcom: Add support for root clock generators (RCGs)) Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06clk: qcom: Properly change rates for ahbix clockStephen Boyd
commit 9d3745d44a7faa7d24db7facb1949a1378162f3e upstream. The ahbix clock can never be turned off in practice. To change the rates we need to switch the mux off the M/N counter to an always on source (XO), reprogram the M/N counter to get the rate we want and finally switch back to the M/N counter. Add a new ops structure for this type of clock so that we can set the rate properly. Fixes: c99e515a92e9 "clk: qcom: Add IPQ806X LPASS clock controller (LCC) driver" Tested-by: Kenneth Westfield <kwestfie@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06clk: qcom: Fix i2c frequency tableStephen Boyd
commit 0bf0ff82c34da02ee5795101b328225a2d519594 upstream. PXO is 25MHz, not 27MHz. Fix the table. Fixes: 24d8fba44af3 "clk: qcom: Add support for IPQ8064's global clock controller (GCC)" Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Reviewed-by: Andy Gross <agross@codeaurora.org> Tested-by: Andy Gross <agross@codeaurora.org> Signed-off-by: Michael Turquette <mturquette@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06clk: tegra: Use the proper parent for plld_dsiThierry Reding
commit c1d676cec572544616273d5853cb7cc38fbaa62b upstream. The current parent, plld_out0, does not exist. The proper name is pll_d_out0. While at it, rename the plld_dsi clock to pll_d_dsi_out to be more consistent with other clock names. Fixes: b270491eb9a0 ("clk: tegra: Define PLLD_DSI and remove dsia(b)_mux") Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06clk: tegra: Register the proper number of resetsThierry Reding
commit 5e43e259171e1eee8bc074d9c44be434e685087b upstream. The number of resets controls is 32 times the number of peripheral register banks rather than 32 times the number of clocks. This reduces (drastically) the number of reset controls registered from 10080 (315 clocks * 32) to 224 (6 peripheral register banks * 32). This also fixes a potential crash because trying to use any of the excess reset controls (224-10079) would have caused accesses beyond the array bounds of the peripheral register banks definition array. Cc: Peter De Schrijver <pdeschrijver@nvidia.com> Cc: Prashant Gaikwad <pgaikwad@nvidia.com> Fixes: 6d5b988e7dc5 ("clk: tegra: implement a reset driver") Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06clk: samsung: exynos4: Disable ARMCLK down feature on Exynos4210 SoCBartlomiej Zolnierkiewicz
commit 3a9e9cb65be84d6c64fbe9c69a73c15d59f29454 upstream. Commit 42773b28e71d ("clk: samsung: exynos4: Enable ARMCLK down feature") enabled ARMCLK down feature on all Exynos4 SoCs. Unfortunately on Exynos4210 SoC ARMCLK down feature causes a lockup when ondemand cpufreq governor is used. Fix it by limiting ARMCLK down feature to Exynos4x12 SoCs. This patch was tested on: - Exynos4210 SoC based Trats board - Exynos4210 SoC based Origen board - Exynos4412 SoC based Trats2 board - Exynos4412 SoC based Odroid-U3 board Cc: Daniel Drake <drake@endlessm.com> Cc: Tomasz Figa <t.figa@samsung.com> Cc: Kukjin Kim <kgene@kernel.org> Fixes: 42773b28e71d ("clk: samsung: exynos4: Enable ARMCLK down feature") Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Michael Turquette <mturquette@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06gpio: mvebu: Fix mask/unmask managment per irq chip typeGregory CLEMENT
commit 61819549f572edd7fce53f228c0d8420cdc85f71 upstream. Level IRQ handlers and edge IRQ handler are managed by tow different sets of registers. But currently the driver uses the same mask for the both registers. It lead to issues with the following scenario: First, an IRQ is requested on a GPIO to be triggered on front. After, this an other IRQ is requested for a GPIO of the same bank but triggered on level. Then the first one will be also setup to be triggered on level. It leads to an interrupt storm. The different kind of handler are already associated with two different irq chip type. With this patch the driver uses a private mask for each one which solves this issue. It has been tested on an Armada XP based board and on an Armada 375 board. For the both boards, with this patch is applied, there is no such interrupt storm when running the previous scenario. This bug was already fixed but in a different way in the legacy version of this driver by Evgeniy Dushistov: 9ece8839b1277fb9128ff6833411614ab6c88d68 "ARM: orion: Fix for certain sequence of request_irq can cause irq storm". The fact the new version of the gpio drive could be affected had been discussed there: http://thread.gmane.org/gmane.linux.ports.arm.kernel/344670/focus=364012 Reported-by: Evgeniy A. Dushistov <dushistov@mail.ru> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06xtensa: ISS: fix locking in TAP network adapterMax Filippov
commit 24e94454c8cb6a13634f5a2f5a01da53a546a58d upstream. - don't lock lp->lock in the iss_net_timer for the call of iss_net_poll, it will lock it itself; - invert order of lp->lock and opened_lock acquisition in the iss_net_open to make it consistent with iss_net_poll; - replace spin_lock with spin_lock_bh when acquiring locks used in iss_net_timer from non-atomic context; - replace spin_lock_irqsave with spin_lock_bh in the iss_net_start_xmit as the driver doesn't use lp->lock in the hard IRQ context; - replace __SPIN_LOCK_UNLOCKED(lp.lock) with spin_lock_init, otherwise lockdep is unhappy about using non-static key. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06xtensa: provide __NR_sync_file_range2 instead of __NR_sync_file_rangeMax Filippov
commit 01e84c70fe40c8111f960987bcf7f931842e6d07 upstream. xtensa actually uses sync_file_range2 implementation, so it should define __NR_sync_file_range2 as other architectures that use that function. That fixes userspace interface (that apparently never worked) and avoids special-casing xtensa in libc implementations. See the thread ending at http://lists.busybox.net/pipermail/uclibc/2015-February/048833.html for more details. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06xtensa: xtfpga: fix hardware lockup caused by LCD driverMax Filippov
commit 4949009eb8d40a441dcddcd96e101e77d31cf1b2 upstream. LCD driver is always built for the XTFPGA platform, but its base address is not configurable, and is wrong for ML605/KC705. Its initialization locks up KC705 board hardware. Make the whole driver optional, and its base address and bus width configurable. Implement 4-bit bus access method. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06ACPI / scan: Annotate physical_node_lock in acpi_scan_is_offline()Rafael J. Wysocki
commit 4c533c801d1c9b5c38458a0e7516e0cf50643782 upstream. acpi_scan_is_offline() may be called under the physical_node_lock lock of the given device object's parent, so prevent lockdep from complaining about that by annotating that instance with SINGLE_DEPTH_NESTING. Fixes: caa73ea158de (ACPI / hotplug / driver core: Handle containers in a special way) Reported-and-tested-by: Xie XiuQi <xiexiuqi@huawei.com> Reviewed-by: Toshi Kani <toshi.kani@hp.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06ACPICA: Store GPE register enable masks upfrontRafael J. Wysocki
commit 0ee0d34985ceffe4036319e1e46df8bff591b9e3 upstream. It is reported that ACPI interrupts do not work any more on Dell Latitude D600 after commit c50f13c672df (ACPICA: Save current masks of enabled GPEs after enable register writes). The problem turns out to be related to the fact that the enable_mask and enable_for_run GPE bit masks are not in sync (in the absence of any system suspend/resume events) for at least one GPE register on that machine. Address this problem by writing the enable_for_run mask into enable_mask as soon as enable_for_run is updated instead of doing that only after the subsequent register write has succeeded. For consistency, update acpi_hw_gpe_enable_write() to store the bit mask to be written into the GPE register in enable_mask unconditionally before the write. Since the ACPI_GPE_SAVE_MASK flag is not necessary any more after that, drop it along with the symbols depending on it. Reported-and-tested-by: Jim Bos <jim876@xs4all.nl> Fixes: c50f13c672df (ACPICA: Save current masks of enabled GPEs after enable register writes) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06ACPICA: Tables: Don't release ACPI_MTX_TABLES in ↵Octavian Purdila
acpi_tb_install_standard_table(). commit 77ddc2fe08329e375505bc36a3df3233fe57317b upstream. ACPICA commit c70434d4da13e65b6163c79a5aa16b40193631c7 ACPI_MTX_TABLES is acquired and released by the callers of acpi_tb_install_standard_table() so releasing it in the function itself is causing the following error in Linux kernel if the table is reloaded: ACPI Error: Mutex [0x2] is not acquired, cannot release (20141107/utmutex-321) Call Trace: [<ffffffff81b0bd48>] dump_stack+0x4f/0x7b [<ffffffff81546bf5>] acpi_ut_release_mutex+0x47/0x67 [<ffffffff81544357>] acpi_load_table+0x73/0xcb Link: https://github.com/acpica/acpica/commit/c70434d4 Signed-off-by: Octavian Purdila <octavian.purdila@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06ACPICA: Utilities: split IO address types from data type models.Lv Zheng
commit 2b8760100e1de69b6ff004c986328a82947db4ad upstream. ACPICA commit aacf863cfffd46338e268b7415f7435cae93b451 It is reported that on a physically 64-bit addressed machine, 32-bit kernel can trigger crashes in accessing the memory regions that are beyond the 32-bit boundary. The region field's start address should still be 32-bit compliant, but after a calculation (adding some offsets), it may exceed the 32-bit boundary. This case is rare and buggy, but there are real BIOSes leaked with such issues (see References below). This patch fixes this gap by always defining IO addresses as 64-bit, and allows OSPMs to optimize it for a real 32-bit machine to reduce the size of the internal objects. Internal acpi_physical_address usages in the structures that can be fixed by this change include: 1. struct acpi_object_region: acpi_physical_address address; 2. struct acpi_address_range: acpi_physical_address start_address; acpi_physical_address end_address; 3. struct acpi_mem_space_context; acpi_physical_address address; 4. struct acpi_table_desc acpi_physical_address address; See known issues 1 for other usages. Note that acpi_io_address which is used for ACPI_PROCESSOR may also suffer from same problem, so this patch changes it accordingly. For iasl, it will enforce acpi_physical_address as 32-bit to generate 32-bit OSPM compatible tables on 32-bit platforms, we need to define ACPI_32BIT_PHYSICAL_ADDRESS for it in acenv.h. Known issues: 1. Cleanup of mapped virtual address In struct acpi_mem_space_context, acpi_physical_address is used as a virtual address: acpi_physical_address mapped_physical_address; It is better to introduce acpi_virtual_address or use acpi_size instead. This patch doesn't make such a change. Because this should be done along with a change to acpi_os_map_memory()/acpi_os_unmap_memory(). There should be no functional problem to leave this unchanged except that only this structure is enlarged unexpectedly. Link: https://github.com/acpica/acpica/commit/aacf863c Reference: https://bugzilla.kernel.org/show_bug.cgi?id=87971 Reference: https://bugzilla.kernel.org/show_bug.cgi?id=79501 Reported-and-tested-by: Paul Menzel <paulepanter@users.sourceforge.net> Reported-and-tested-by: Sial Nije <sialnije@gmail.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06ASoC: pcm512x: Fix divide by zero issueHoward Mitchell
commit f073faa73626f41db7050a69edd5074c53ce6d6c upstream. If den=1 and pllin_rate>20MHz then den and num are adjusted to 0 causing a divide by zero error a few lines further on. Therefore this patch correctly scales num and den such that pllin_rate/den < 20MHz as required in the device data sheet. Signed-off-by: Howard Mitchell <hm@hmbedded.co.uk> Signed-off-by: Mark Brown <broonie@sirena.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06ASoC: pcm512x: Add 'Analogue' prefix to analogue volume controlsHoward Mitchell
commit 4d9b13c7cc803fbde59d7e998f7de2b9a2101c7e upstream. This is to ensure that 'alsactl restore' does not apply default initialisation as the chip reset defaults are preferred. Signed-off-by: Howard Mitchell <hm@hmbedded.co.uk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06ASoC: davinci-evm: drop un-necessary remove functionManish Badarkhe
commit a57069e33fbc6625f39e1b09c88ea44629a35206 upstream. As davinci card gets registered using 'devm_' api there is no need to unregister the card in 'remove' function. Hence drop the 'remove' function. Fixes: ee2f615d6e59c (ASoC: davinci-evm: Add device tree binding) Signed-off-by: Manish Badarkhe <manishvb@ti.com> Signed-off-by: Jyri Sarha <jsarha@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06ASoC: wm8741: Fix rates constraints valuesSergej Sawazki
commit 8787041d9bb832b9449b1eb878cedcebce42c61a upstream. The WM8741 DAC supports the following typical audio sampling rates: 44.1kHz, 88.2kHz, 176.4kHz (eg: with a master clock of 22.5792MHz) 32kHz, 48kHz, 96kHz, 192kHz (eg: with a master clock of 24.576MHz) For the rates lists, we should use 82000 instead of 88235, 176400 instead of 1764000 and 192000 instead of 19200 (seems to be a typo). Signed-off-by: Sergej Sawazki <ce3a@gmx.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06ASoC: cs4271: Increase delay time after resetPascal Huerst
commit 74ff960222d90999508b4ba0d3449f796695b6d5 upstream. The delay time after a reset in the codec probe callback was too short, and did not work on certain hw because the codec needs more time to power on. This increases the delay time from 1us to 1ms. Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com> Acked-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06powerpc/cell: Fix cell iommu after it_page_shift changesMichael Ellerman
commit 7261b956b276aa97fbf60d00f1d7717d2ea6ee78 upstream. The patch to add it_page_shift incorrectly changed the increment of uaddr to use it_page_shift, rather then (1 << it_page_shift). This broke booting on at least some Cell blades, as the iommu was basically non-functional. Fixes: 3a553170d35d ("powerpc/iommu: Add it_page_shift field to determine iommu page size") Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06powerpc/cell: Fix crash in iic_setup_cpu() after per_cpu changesMichael Ellerman
commit b0dd00addc5035f87ec9c5820dacc1ebc7fcb3e6 upstream. The conversion from __get_cpu_var() to this_cpu_ptr() in iic_setup_cpu() is wrong. It causes an oops at boot. We need the per-cpu address of struct cpu_iic, not cpu_iic.regs->prio. Sparse noticed this, because we pass a non-iomem pointer to out_be64(), but we obviously don't check the sparse results often enough. Fixes: 69111bac42f5 ("powerpc: Replace __get_cpu_var uses") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06powerpc: Fix missing L2 cache size in /sys/devices/system/cpuDave Olson
commit f7e9e358362557c3aa2c1ec47490f29fe880a09e upstream. This problem appears to have been introduced in 2.6.29 by commit 93197a36a9c1 "Rewrite sysfs processor cache info code". This caused lscpu to error out on at least e500v2 devices, eg: error: cannot open /sys/devices/system/cpu/cpu0/cache/index2/size: No such file or directory Some embedded powerpc systems use cache-size in DTS for the unified L2 cache size, not d-cache-size, so we need to allow for both DTS names. Added a new CACHE_TYPE_UNIFIED_D cache_type_info structure to handle this. Fixes: 93197a36a9c1 ("powerpc: Rewrite sysfs processor cache info code") Signed-off-by: Dave Olson <olson@cumulusnetworks.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06powerpc/powernv: Don't map M64 segments using M32DTGavin Shan
commit 027fa02f84e851e21daffdf8900d6117071890f8 upstream. If M64 has been supported, the prefetchable 64-bits memory resources shouldn't be mapped to the corresponding PE# via M32DT. Unfortunately, we're doing that in pnv_ioda_setup_pe_seg() wrongly. The issue was introduced by commit 262af55 ("powerpc/powernv: Enable M64 aperatus for PHB3"). The patch fixes the issue by simply skipping M64 resources when updating to M32DT. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06arm64: errata: add workaround for cortex-a53 erratum #845719Will Deacon
commit 905e8c5dcaa147163672b06fe9dcb5abaacbc711 upstream. When running a compat (AArch32) userspace on Cortex-A53, a load at EL0 from a virtual address that matches the bottom 32 bits of the virtual address used by a recent load at (AArch64) EL1 might return incorrect data. This patch works around the issue by writing to the contextidr_el1 register on the exception return path when returning to a 32-bit task. This workaround is patched in at runtime based on the MIDR value of the processor. Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06arm64: apply alternatives for !SMP kernelsMark Rutland
commit 137650aad96c9594683445e41afa8ac5a2097520 upstream. Currently we only perform alternative patching for kernels built with CONFIG_SMP, as we call apply_alternatives_all() in smp.c, which is only built for CONFIG_SMP. Thus !SMP kernels may not have necessary alternatives patched in. This patch ensures that we call apply_alternatives_all() once all CPUs are booted, even for !SMP kernels, by having the smp_init_cpus() stub call this for !SMP kernels via up_late_init. A new wrapper, do_post_cpus_up_work, is added so we can hook other calls here later (e.g. boot mode logging). Cc: Andre Przywara <andre.przywara@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Fixes: e039ee4ee3fcf174 ("arm64: add alternative runtime patching") Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06arm64: Adjust EFI libstub object include logicSteve Capper
commit ad08fd494bf00c03ae372e0bbd9cefa37bf608d6 upstream. Commit f4f75ad5 ("efi: efistub: Convert into static library") introduced a static library for EFI stub, libstub. The EFI libstub directory is referenced by the kernel build system via a obj subdirectory rule in: drivers/firmware/efi/Makefile Unfortunately, arm64 also references the EFI libstub via: libs-$(CONFIG_EFI_STUB) += drivers/firmware/efi/libstub/ If we're unlucky, the kernel build system can enter libstub via two simultaneous threads resulting in build failures such as: fixdep: error opening depfile: drivers/firmware/efi/libstub/.efi-stub-helper.o.d: No such file or directory scripts/Makefile.build:257: recipe for target 'drivers/firmware/efi/libstub/efi-stub-helper.o' failed make[1]: *** [drivers/firmware/efi/libstub/efi-stub-helper.o] Error 2 Makefile:939: recipe for target 'drivers/firmware/efi/libstub' failed make: *** [drivers/firmware/efi/libstub] Error 2 make: *** Waiting for unfinished jobs.... This patch adjusts the arm64 Makefile to reference the compiled library explicitly (as is currently done in x86), rather than the directory. Fixes: f4f75ad5 efi: efistub: Convert into static library Signed-off-by: Steve Capper <steve.capper@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06arm64: head.S: ensure visibility of page tablesMark Rutland
commit 91d57155dc5ab4b311624b7ee570339b6af19ad5 upstream. After writing the page tables, we use __inval_cache_range to invalidate any stale cache entries. Strongly Ordered memory accesses are not ordered w.r.t. cache maintenance instructions, and hence explicit memory barriers are required to provide this ordering. However, __inval_cache_range was written to be used on Normal Cacheable memory once the MMU and caches are on, and does not have any barriers prior to the DC instructions. This patch adds a DMB between the page tables being written and the corresponding cachelines being invalidated, ensuring that the invalidation makes the new data visible to subsequent cacheable accesses. A barrier is not required before the prior invalidate as we do not access the page table memory area prior to this, and earlier barriers in preserve_boot_args and set_cpu_boot_mode_flag ensures ordering w.r.t. any stores performed prior to entering Linux. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Fixes: c218bca74eeafa2f ("arm64: Relax the kernel cache requirements for boot") Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06arm64: fix midr range for Cortex-A57 erratum 832075Bo Yan
commit 6d1966dfd6e0ad2f8aa4b664ae1a62e33abe1998 upstream. Register MIDR_EL1 is masked to get variant and revision fields, then compared against midr_range_min and midr_range_max when checking whether CPU is affected by any particular erratum. However, variant and revision fields in MIDR_EL1 are separated by 16 bits, so the min and max of midr range should be constructed accordingly, otherwise the patch will not be applied when variant field is non-0. Acked-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Bo Yan <byan@nvidia.com> [will: use MIDR_VARIANT_SHIFT to construct upper bound] Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06Bluetooth: ath3k: Add support Atheros AR5B195 combo Mini PCIe cardAlexander Ploumistos
commit 2eeff0b4317a02f0e281df891d990194f0737aae upstream. Add 04f2:aff1 to ath3k.c supported devices list and btusb.c blacklist, so that the device can load the ath3k firmware and re-enumerate itself as an AR3011 device. T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04f2 ProdID=aff1 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Alexander Ploumistos <alexpl@fedoraproject.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06iser-target: Fix possible deadlock in RDMA_CM connection errorSagi Grimberg
commit 4a579da2586bd3b79b025947ea24ede2bbfede62 upstream. Before we reach to connection established we may get an error event. In this case the core won't teardown this connection (never established it), so we take care of freeing it ourselves. Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06iser-target: Fix session hang in case of an rdma read DIF errorSagi Grimberg
commit 364189f0ada5478e4faf8a552d6071a650d757cd upstream. This hang was a result of a missing command put when a DIF error occurred during a rdma read (and we sent an CHECK_CONDITION error without passing it to the backend). Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06target/file: Fix SG table for prot_buf initializationAkinobu Mita
commit c836777830428372074d5129ac513e1472c99791 upstream. In fd_do_prot_rw(), it allocates prot_buf which is used to copy from se_cmd->t_prot_sg by sbc_dif_copy_prot(). The SG table for prot_buf is also initialized by allocating 'se_cmd->t_prot_nents' entries of scatterlist and setting the data length of each entry to PAGE_SIZE at most. However if se_cmd->t_prot_sg contains a clustered entry (i.e. sg->length > PAGE_SIZE), the SG table for prot_buf can't be initialized correctly and sbc_dif_copy_prot() can't copy to prot_buf. (This actually happened with TCM loopback fabric module) As prot_buf is allocated by kzalloc() and it's physically contiguous, we only need a single scatterlist entry. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06target/file: Fix UNMAP with DIF protection supportAkinobu Mita
commit 64d240b721b21e266ffde645ec965c3b6d1c551f upstream. When UNMAP command is issued with DIF protection support enabled, the protection info for the unmapped region is remain unchanged. So READ command for the region causes data integrity failure. This fixes it by invalidating protection info for the unmapped region by filling with 0xff pattern. This change also adds helper function fd_do_prot_fill() in order to reduce code duplication with existing fd_format_prot(). Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06target/file: Fix BUG() when CONFIG_DEBUG_SG=y and DIF protection enabledAkinobu Mita
commit 38da0f49e8aa1649af397d53f88e163d0e60c058 upstream. When CONFIG_DEBUG_SG=y and DIF protection support enabled, kernel BUG()s are triggered due to the following two issues: 1) prot_sg is not initialized by sg_init_table(). When CONFIG_DEBUG_SG=y, scatterlist helpers check sg entry has a correct magic value. 2) vmalloc'ed buffer is passed to sg_set_buf(). sg_set_buf() uses virt_to_page() to convert virtual address to struct page, but it doesn't work with vmalloc address. vmalloc_to_page() should be used instead. As prot_buf isn't usually too large, so fix it by allocating prot_buf by kmalloc instead of vmalloc. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06target: Fix COMPARE_AND_WRITE with SG_TO_MEM_NOALLOC handlingNicholas Bellinger
commit c8e639852ad720499912acedfd6b072325fd2807 upstream. This patch fixes a bug for COMPARE_AND_WRITE handling with fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC. It adds the missing allocation for cmd->t_bidi_data_sg within transport_generic_new_cmd() that is used by COMPARE_AND_WRITE for the initial READ payload, even if the fabric is already providing a pre-allocated buffer for cmd->t_data_sg. Also, fix zero-length COMPARE_AND_WRITE handling within the compare_and_write_callback() and target_complete_ok_work() to queue the response, skipping the initial READ. This fixes COMPARE_AND_WRITE emulation with loopback, vhost, and xen-backend fabric drivers using SG_TO_MEM_NOALLOC. Reported-by: Christoph Hellwig <hch@lst.de> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06iscsi-target: Convert iscsi_thread_set usage to kthread.hNicholas Bellinger
commit 88dcd2dab5c23b1c9cfc396246d8f476c872f0ca upstream. This patch converts iscsi-target code to use modern kthread.h API callers for creating RX/TX threads for each new iscsi_conn descriptor, and releasing associated RX/TX threads during connection shutdown. This is done using iscsit_start_kthreads() -> kthread_run() to start new kthreads from within iscsi_post_login_handler(), and invoking kthread_stop() from existing iscsit_close_connection() code. Also, convert iscsit_logout_post_handler_closesession() code to use cmpxchg when determing when iscsit_cause_connection_reinstatement() needs to sleep waiting for completion. Reported-by: Sagi Grimberg <sagig@mellanox.com> Tested-by: Sagi Grimberg <sagig@mellanox.com> Cc: Slava Shwartsman <valyushash@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06scsi: storvsc: Fix a bug in copy_from_bounce_buffer()K. Y. Srinivasan
commit 8de580742fee8bc34d116f57a20b22b9a5f08403 upstream. We may exit this function without properly freeing up the maapings we may have acquired. Fix the bug. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Long Li <longli@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06UBI: fix check for "too many bytes"Brian Norris
commit 299d0c5b27346a77a0777c993372bf8777d4f2e5 upstream. The comparison from the previous line seems to have been erroneously (partially) copied-and-pasted onto the next. The second line should be checking req.bytes, not req.lnum. Coverity CID #139400 Signed-off-by: Brian Norris <computersforpeace@gmail.com> [rw: Fixed comparison] Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06UBI: initialize LEB number variableBrian Norris
commit f16db8071ce18819fbd705ddcc91c6f392fb61f8 upstream. In some of the 'out_not_moved' error paths, lnum may be used uninitialized. Don't ignore the warning; let's fix it. This uninitialized variable doesn't have much visible effect in the end, since we just schedule the PEB for erasure, and its LEB number doesn't really matter (it just gets printed in debug messages). But let's get it straight anyway. Coverity CID #113449 Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06UBI: fix out of bounds writeBrian Norris
commit d74adbdb9abf0d2506a6c4afa534d894f28b763f upstream. If aeb->len >= vol->reserved_pebs, we should not be writing aeb into the PEB->LEB mapping. Caught by Coverity, CID #711212. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06UBI: account for bitflips in both the VID header and dataBrian Norris
commit 8eef7d70f7c6772c3490f410ee2bceab3b543fa1 upstream. We are completely discarding the earlier value of 'bitflips', which could reflect a bitflip found in ubi_io_read_vid_hdr(). Let's use the bitwise OR of header and data 'bitflip' statuses instead. Coverity CID #1226856 Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for ↵Thomas D
O= option in Makefile commit f82263c6989c31ae9b94cecddffb29dcbec38710 upstream. Since commit ee0778a30153 ("tools/power: turbostat: make Makefile a bit more capable") turbostat's Makefile is using [...] BUILD_OUTPUT := $(PWD) [...] which obviously causes trouble when building "turbostat" with make -C /usr/src/linux/tools/power/x86/turbostat ARCH=x86 turbostat because GNU make does not update nor guarantee that $PWD is set. This patch changes the Makefile to use $CURDIR instead, which GNU make guarantees to set and update (i.e. when using "make -C ...") and also adds support for the O= option (see "make help" in your root of your kernel source tree for more details). Link: https://bugs.gentoo.org/show_bug.cgi?id=533918 Fixes: ee0778a30153 ("tools/power: turbostat: make Makefile a bit more capable") Signed-off-by: Thomas D. <whissi@whissi.de> Cc: Mark Asselstine <mark.asselstine@windriver.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06tools lib traceevent kbuffer: Remove extra update to data pointer in PADDINGSteven Rostedt (Red Hat)
commit c5e691928bf166ac03430e957038b60adba3cf6c upstream. When a event PADDING is hit (a deleted event that is still in the ring buffer), translate_data() sets the length of the padding and also updates the data pointer which is passed back to the caller. This is unneeded because the caller also updates the data pointer with the passed back length. translate_data() should not update the pointer, only set the length. Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: http://lkml.kernel.org/r/20150324135923.461431960@goodmis.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTHAnton Blanchard
commit 9a5cbce421a283e6aea3c4007f141735bf9da8c3 upstream. We cap 32bit userspace backtraces to PERF_MAX_STACK_DEPTH (currently 127), but we forgot to do the same for 64bit backtraces. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06perf tools: Work around lack of sched_getcpu in glibc < 2.6.Vinson Lee
commit e1e455f4f4d35850c30235747620d0d078fe9f64 upstream. This patch fixes this build error with glibc < 2.6. CC util/cloexec.o cc1: warnings being treated as errors util/cloexec.c: In function ‘perf_flag_probe’: util/cloexec.c:24: error: implicit declaration of function ‘sched_getcpu’ util/cloexec.c:24: error: nested extern declaration of ‘sched_getcpu’ make: *** [util/cloexec.o] Error 1 Signed-off-by: Vinson Lee <vlee@twitter.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Yann Droneaud <ydroneaud@opteya.com> Link: http://lkml.kernel.org/r/1427137761-16119-1-git-send-email-vlee@twopensource.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06perf tools: Fix perf-read-vdsox32 not building and lib64 install dirH.J. Lu
commit 76aea7731e7050c066943a1d7456ec6510702601 upstream. Commit: c6e5e9fbc3ea ("perf tools: Fix building error in x86_64 when dwarf unwind is on") removed the definition of IS_X86_64 but not all places using it, with the consequence that perf-read-vdsox32 would not be built anymore, and the default lib install directory was 'lib' instead of 'lib64'. Also needs to go to v3.19. Signed-off-by: H.J. Lu <hjl.tools@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Link: http://lkml.kernel.org/r/CAMe9rOqpGVq3D88w+D15ef7sv6G6k57ZeTvxBm46=WFgzo9p1w@mail.gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-06perf symbols: Define STT_GNU_IFUNC for glibc 2.9 and older.Vinson Lee
commit 4e31050f482c02c822b150d71cf1ea5be7c9d6e4 upstream. The token STT_GNU_IFUNC is not available with glibc 2.9 and older. Define this token if it is not already defined. This patch fixes this build errors with older versions of glibc. CC util/symbol-elf.o util/symbol-elf.c: In function ‘elf_sym__is_function’: util/symbol-elf.c:75: error: ‘STT_GNU_IFUNC’ undeclared (first use in this function) util/symbol-elf.c:75: error: (Each undeclared identifier is reported only once util/symbol-elf.c:75: error: for each function it appears in.) make: *** [util/symbol-elf.o] Error 1 Signed-off-by: Vinson Lee <vlee@twitter.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Anton Blanchard <anton@samba.org> Cc: Avi Kivity <avi@cloudius-systems.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Stephane Eranian <eranian@google.com> Cc: Waiman Long <Waiman.Long@hp.com> Link: http://lkml.kernel.org/r/1423528286-13630-1-git-send-email-vlee@twopensource.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-05-12 06:20:54 +0000