| Age | Commit message (Collapse) | Author |
|---|
|
Update the sun8i-h3-orangepi-plus.dts model string to reflect that it
is valid for both the Orange Pi Plus and the Orange Pi Plus 2.
This is also meant to help users realize that it is not valid for
the new Orange Pi Plus 2E, which will get its own dts.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Orange Pi Plus really is an Orange Pi 2 extended with:
1) A sata <-> usb bridge connected to ehci3
2) An eMMC on mmc2
3) An external gigabit ethernet phy instead of the integrated 100Mbit phy
This commit changes the dts to reflect this by making it include
the Orange Pi 2 dts and then adding the extra bits.
Note that the difference in ethernet phy is not taken into account
because we do not have an ethernet driver for the H3 yet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Fix the following issues with the gpio_keys node:
1) Use of undocumented input-name property
2) Use of a unit-address on the sw2 node
3) Having "PL03" in the pinctrl node which does not exist, this should
be "PL3"
And add support for the sw2 button on the board.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Fix sun8i-h3-orangepi-plus.dts:
1) Having 2 pio nodes, by merging these into one
2) Having the pio and r_pio nodes before the mmc nodes, while they
should be sorted by alphabet
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Orangepi Plus has a 16GB eMMC, the vcc, the lack of pull-ups and
the use of the hw-reset pin have all been verified with the board
schematic.
With this dts node for mmc2, the eMMC runs at the following ios settings:
clock: 52000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 3 (8 bits)
timing spec: 8 (mmc DDR52)
signal voltage: 0 (3.30 V)
driver type: 0 (driver type B)
Note the mmcblk1boot0/boot1 partitions are unused as the BROM will load
the SPL from 8k from the start of the main blockdev, just as with a
regular sdcard in mmc0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Orangepi Plus and Orangepi Plus 2 have a realtek rtl8189etv sdio
wifi chip. This commit adds a device-tree node to power it up, so
that the mmc subsys can scan it, and enables the mmc controller which
is connected to it.
Note that this just makes the wifi controller show up as a sdio device.
In order for it to work a compatible sdio driver is necessary, an out
of tree driver is available here:
https://github.com/jwrdegoede/rtl8189ES_linux/
Binding the driver is not done through device tree, but through sdio
vendor- and device-id, so it can safely be enabled in devicetree
without having a driver upstream yet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Enable the ir receiver found on the orangepi plus board.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Enable the 2 USB host controllers used on the Orange Pi Plus
and add the necessary regulators.
Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
OrangePi Plus board has dwo leds - green ("pwr") and red ("status")
and a switch ("sw4"). This patch describes them in a devicetree.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
