| Age | Commit message (Collapse) | Author |
|---|
|
Out-of-the-box the analogue camera adapter fails detecting with the
following error:
[ 6.503046] adv7280 2-0021: adv7280_probe:Analog Device adv7280 not detected -6!
Unfortunately, the camera seems to be held in reset due to the BL_ON pin
not being serviced.
Fix this by hogging the camera_nreset aka BL_ON pin to output high.
Related-to: ELB-2580
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
eMMC, used in Colibri iMX7D eMMC modules, supports
200Mhz mode with vccq=1.8v.
Remove the max-frequency limit, it increases the performance significantly:
== before fix ====
root@colibri-imx7-emmc:~# hdparm -t /dev/mmcblk1
/dev/mmcblk1:
Timing buffered disk reads: `^H252 MB in 3.02 seconds = 83.54 MB/sec
==================
=== after fix ====
root@colibri-imx7-emmc:~# hdparm -t /dev/mmcblk0
/dev/mmcblk0:
Timing buffered disk reads: 408 MB in 3.00 seconds = 135.94 MB/sec
==================
Related-to: ELB-1442
Fixes: f928a4a377e4 ("ARM: dts: imx7: add Toradex Colibri iMX7D
1GB (eMMC) support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
The interface of Apalis modules is MXM3, not SODIMM.
Just fix the name of the reset touch pin.
Fixes: 96458caa3562 ("ARM: dts: imx6: Add touchscreens used
on Toradex eval boards")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
toradex_4.14-2.0.x-imx-next
Conflicts:
sound/soc/codecs/sgtl5000.c
|
|
This is the 4.14.159 stable release
Conflicts:
arch/arm/Kconfig.debug
arch/arm/boot/dts/imx7s.dtsi
arch/arm/mach-imx/cpuidle-imx6sx.c
drivers/crypto/caam/caamalg.c
drivers/crypto/mxs-dcp.c
drivers/dma/imx-sdma.c
drivers/input/keyboard/imx_keypad.c
drivers/net/can/flexcan.c
drivers/net/can/rx-offload.c
drivers/net/wireless/ath/ath10k/pci.c
drivers/pci/dwc/pci-imx6.c
drivers/spi/spi-fsl-lpspi.c
drivers/usb/dwc3/gadget.c
|
|
commit 287897f9aaa2ad1c923d9875914f57c4dc9159c8 upstream.
The MMC card detection GPIO polarity is active low on TAO3530, like in many
other similar boards. Now the card is not detected and it is unable to
mount rootfs from an SD card.
Fix this by using the correct polarity.
This incorrect polarity was defined already in the commit 30d95c6d7092
("ARM: dts: omap3: Add Technexion TAO3530 SOM omap3-tao3530.dtsi") in v3.18
kernel and later changed to use defined GPIO constants in v4.4 kernel by
the commit 3a637e008e54 ("ARM: dts: Use defined GPIO constants in flags
cell for OMAP2+ boards").
While the latter commit did not introduce the issue I'm marking it with
Fixes tag due the v4.4 kernels still being maintained.
Fixes: 3a637e008e54 ("ARM: dts: Use defined GPIO constants in flags cell for OMAP2+ boards")
Cc: linux-stable <stable@vger.kernel.org> # 4.4+
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4f9007d692017cef38baf2a9b82b7879d5b2407b upstream.
Since v4.7 the dma initialization requires that there is a
device tree property for "rx" and "tx" channels which is
not provided by the pdata-quirks initialization.
By conversion of the mmc3 setup to device tree this will
finally allows to remove the OpenPandora wlan specific omap3
data-quirks.
Fixes: 81eef6ca9201 ("mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.7+
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5719ac19fc32d892434939c1756c2f9a8322e6ef ]
"arm,cortex-a15-pmu" is not a valid fallback compatible string for an
Cortex-A7 PMU, so drop it.
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f3b2f758ec1e6cdb13c925647cbd8ad4938b78fb ]
There's a bug in dtc in checking for duplicate node names when there's
another section (e.g. "/ { };"). In this case, skeleton.dtsi provides
another section. Upon removal of skeleton.dtsi, the dtb fails to build
due to a duplicate node 'fixedregulator@0'. As both nodes were pretty
much the same 3.3V fixed regulator, it hasn't really mattered. Fix this
by renaming the nodes to something unique. In the process, drop the
unit-address which shouldn't be present wtihout reg property.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c40ad24254f1dbd54f2df5f5f524130dc1862122 ]
PXA25xx SoCs don't have a USB controller, so drop the node from the
common pxa2xx.dtsi base file. Both pxa27x and pxa3xx have a dedicated
node already anyway.
While at it, unify the names for the nodes across all pxa platforms.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reported-by: Sergey Yanovich <ynvich@gmail.com>
Link: https://patchwork.kernel.org/patch/8375421/
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7f4b001b7f6e0480b5bdab9cd8ce1711e43e5cb5 ]
There's a bug in dtc in checking for duplicate node names when there's
another section (e.g. "/ { };"). In this case, skeleton.dtsi provides
another section. Upon removal of skeleton.dtsi, the dtb fails to build
due to a duplicate node 'fixedregulator@0'. As both nodes were pretty
much the same 3.3V fixed regulator, it hasn't really mattered. Fix this
by renaming the nodes to something unique. In the process, drop the
unit-address which shouldn't be present wtihout reg property.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 400583983f8a8e95ec02c9c9e2b50188753a87fb ]
gpio-pxa uses two cell to encode the interrupt source: the pin number
and the trigger type. Adjust the device node accordingly.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 438a44ce7e51ce571f942433c6c7cb87c4c0effd ]
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ed5fc60b909427be6ca93d3e07a0a5f296d7000a ]
Our HDMI output endpoint on the A10s DTSI has a warning under DTC: "graph
node has single child node 'endpoint', #address-cells/#size-cells are not
necessary". Fix this by removing those properties.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit efc2e0bd9594060915696a418564aefd0270b1d6 ]
It is not correct to assign the 24MHz clock oscillator to the GPIO
ports.
Fix it by assigning the proper GPIO clocks instead.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c955b7aec510145129ca7aaea6ecbf6d748f5ebf ]
According to the Rockchip vendor tree the PMU interrupt number is
76, so fix it accordingly.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6035cbcceb069f87296b3cd0bc4736ad5618bf47 ]
DWC2 hardware module integrated in Samsung SoCs requires some quirks to
operate properly, so use Samsung SoC specific compatible to notify driver
to apply respective fixes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 03d9f8fa2bfdc791865624d3adc29070cf67814e ]
There is no functional change from this, but it is confusing to find two
copies of vcc_sys and no vcc_flash when looking in
/sys/class/regulator/*/name.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 998a84c27a7f3f9133d32af64e19c05cec161a1a ]
imx53-voipac-dmm-668 has two memory nodes, but the correct representation
would be to use a single one with two reg entries - one for each RAM chip
select, so fix it accordingly.
Reported-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d88b11ef91b15d0af9c0676cbf4f441a0dff0c56 ]
This sets the partition information on the SQ201 to be read
out from the RedBoot partition table, removes the static
partition table and sets our boot options to mount root from
/dev/mtdblock2 where the squashfs+JFFS2 resides.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
There is now a mainline variant for a regulator-fixed to be enabled
by a clock. Make use of this newly cherry-picked mainline feature.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Some pinmuxings are obviously wrong, originating from a copy/paste
error. This patch corrects that with the following strategy:
- Set all reserved bits to zero
- Leave drive strength and slew rate as is
- Add sensible pull and hysteresis depending on the function of the pin
- Not used pins are muxed to their reset-value defined by the SoC
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
[ Upstream commit a763ecc15d0e37c3a15ff6825183061209832685 ]
OMAP5's Super-Speed USB port has a software mailbox register
that needs to be fed with VBUS and ID events from an external
VBUS/ID comparator.
Without this, Host role will not work correctly.
Fixes: 656c1a65ab55 ("ARM: dts: omap5: enable OTG role for DWC3 controller")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6f270d88a0c4a11725afd8fd2001ae408733afbf ]
at91sam9x5cm comes with a 2Gb NAND flash. Fix the rootfs size to
match this limit.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit df90fc64367ffdb6f1b5c0f0c4940d44832b0174 ]
sama5d4_xplained comes with a 4Gb NAND flash. Increase the rootfs
size to match this limit.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6c700289a3e84d5d3f2a95cf27732a7f7fce105b ]
The size of the register should be the size of the whole memory block,
not just the registers, that are needed.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 656c1a65ab555ee5c7cd0d6aee8ab82ca3c1795f ]
Since SMPS10 and OTG cable detection extcon are described here, and
work to enable OTG power when an OTG cable is plugged in, we can
define OTG mode in the controller (which is disabled by default in
omap5.dtsi).
Tested on OMAP5EVM and Pyra.
Suggested-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b830526f304764753fcb8b4a563a94080e982a6c ]
Add ti,syscon-unaligned-access property to PCIe RC nodes to set
appropriate bits in CTRL_CORE_SMA_SW_7 register to enable workaround for
errata i870.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 11236ef582b8d66290bb3b3710e03ca1d85d8ad8 ]
SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 016add12977bcc30f77d7e48fc9a3a024cb46645 ]
SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ebea2a43fdafdbce918bd7e200b709d6c33b9f3b ]
The power key is controlled solely by the EC, which only tiggeres this
gpio after wakeup.
Fixes immediately return to suspend after wake from LP1.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1c997fe4becdc6fcbc06e23982ceb65621e6572a ]
Fix MMC1 cmd pin pull-up causing issues on carrier boards without
external pull-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 564706f65cda3de52b09e51feb423a43940fe661 ]
There was a dot instead of a comma. Fix this.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a2df0984e73fd9e1dad5fc3f1c307ec3de395e30 ]
It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.
The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e807f0298144c06740022a2f900d86b7f115595e ]
The vmmc phandle, like all power supply property names, must have the
'-supply' suffix.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cf680cc5251487b9a39919c3cda31a108af19cf8 ]
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/dove-cubox.dtb: Warning (i2c_bus_reg): /i2c-mux/i2c@0/clock-generator: I2C bus unit address format error, expected "60"
arch/arm/boot/dts/dove-cubox-es.dtb: Warning (i2c_bus_reg): /i2c-mux/i2c@0/clock-generator: I2C bus unit address format error, expected "60"
arch/arm/boot/dts/dove-cubox.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-cubox-es.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-dove-db.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-sbc-a510.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@10600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dove-sbc-a510.dtb: Warning (spi_bus_bridge): /mbus/internal-regs/spi-ctrl@14600: node name for SPI buses should be 'spi'
arch/arm/boot/dts/orion5x-kuroboxpro.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lschl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lsgl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/orion5x-linkstation-lswtgl.dtb: Warning (i2c_bus_reg): /soc/internal-regs/i2c@11000/rtc: I2C bus unit address format error, expected "32"
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2f967f9e9fa076affb711da1a8389b5d33814fc6 ]
SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ecde29569e3484e1d0a032bf4074449bce4d4a03 ]
The "lcdaclk_b_1" group is muxed with the function "lcd"
but needs a separate entry to be muxed in with "lcda"
rather than "lcd".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2f217d24ecaec2012e628d21e244eef0608656a4 ]
The unit address of the Cortex-A9 SCU device node contains one zero too
many. Remove it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dcbf6b18d81bcdc51390ca1b258c17e2e13b7d0c ]
am335x-evm has only one CPSW external port physically wired, but DT defines
2 ext. ports. As result, PHY connection failure reported for the second
ext. port.
Update DT to reflect am335x-evm board HW configuration, and, while here,
switch to use phy-handle instead of phy_id.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 53dd9dce6979bc54d64a3a09a2fb20187a025be7 ]
The next update of libfdt has a new dependency on INT_MAX. Update the
instances of libfdt_env.h in the kernel to either include the necessary
header with the definition or define it locally.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 131c3eb428ccd5f0c784b9edb4f72ec296a045d2 ]
dtc has new checks for SPI buses. The rk3036 dts file has a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cbbc488ed85061a765cf370c3e41f383c1e0add6 ]
dtc has new checks for I2C buses. Fix the warnings in unit-addresses.
arch/arm/boot/dts/socfpga_cyclone5_de0_sockit.dtb: Warning (i2c_bus_reg): /soc/i2c@ffc04000/adxl345@0: I2C bus unit address format error, expected "53"
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd73a3dd257fb838bd456a18eeee0ef0224b7a40 ]
while compiling an ipq4019 target, dtc will complain:
regulator@b089000 unit address format error, expected "2089000"
The saw0 regulator reg value seems to be
copied and pasted from qcom-ipq8064.dtsi.
This patch fixes the reg value to match that of the
unit address which in turn silences the warning.
(There is no driver for qcom,saw2 right now.
So this went unnoticed)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1ae00833e30c9b4af5cbfda65d75b1de12f74013 ]
This is needed to make the display and venc work properly.
Compare to omap3-beagle.dts.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fa99c21ecb3cd4021a60d0e8bf880e78b5bd0729 ]
Vendor defined U-Boot has changed the partition scheme a while ago:
* kernel partition 6MB
* file system partition uses the remainder up to end of the NAND
* increased size of the environment partition (to get an OneNAND compatible base address)
* shrink the U-Boot partition
Let's be compatible (e.g. Debian kernel built from upstream).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7384a24248eda140a234d356b6c840701ee9f055 ]
we fix penirq polarity, add penirq pinmux and touchscreen
properties.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8905592b6e50cec905e6c6035bbd36201a3bfac1 ]
The omap dss susbystem takes the display aliases to find
out which displays exist. To enable tv-out we must define
an alias.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f6591391373dbff2c0200e1055d4ff86191578d2 ]
* fix connector compatibility (composite)
* add comment for gpio1 23
* add proper #address-cells
* we use only one venc_out channel for composite
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
