| Age | Commit message (Collapse) | Author |
|---|
|
The following devices/functionalities were tested:
* Main UART.
* Ethernet0.
* Ethernet1.
* SD.
* USB host.
* USB otg.
* Display(and its backlight).
* Touchscreen.
* Audio.
* nand.
* i2c and the pcf8563 device.
* The gpio buttons.
* The gpio leds.
* Watchdog
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
|
|
This board is based on the M28 SoM with custom baseboard. Supported
are LEDs, ethernet, PWM, LCD, SD slots.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch converts clk-imx2[38] clocksource_of_init compatible init
associated with fsl,imx2[38]-clkctrl. With arch/arm calling
of_clk_init(NULL) from time_init(), we can now also remove custom
.init_time hooks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
|
|
As all CrystalFontz boards are compatible with "crystalfontz,cfa10036", make it
easier to add future boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
There is no need to print the silicon revision as "TO1.2", just print it as
"1.2" instead:
$ cat /sys/bus/soc/devices/soc0/revision
1.2
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The mxs_restart() function uses of_iomap() which triggers the
following BUG_ON(in_interrupt()) when called in interrupt context
(e.g. thru SYSRQ-B):
SysRq : Resetting
------------[ cut here ]------------
kernel BUG at mm/vmalloc.c:1310!
Internal error: Oops - BUG: 0 [#1] PREEMPT ARM
Modules linked in: i2c_dev
CPU: 0 PID: 0 Comm: swapper Not tainted 3.11.0-rc2-next-20130729-karo+ #196
task: c04e1c38 ti: c04d8000 task.ti: c04d8000
PC is at __get_vm_area_node.clone.25+0x34/0x140
LR is at get_vm_area_caller+0x38/0x44
pc : [<c008a988>] lr : [<c008b434>] psr: 20000013
sp : c04d9db0 ip : 00000001 fp : 00000001
r10: c8800000 r9 : 00000000 r8 : 000000d0
r7 : 00002000 r6 : 00000001 r5 : 00000001 r4 : 00002000
r3 : 00010000 r2 : 00000001 r1 : c04d9db0 r0 : 00002000
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 0005317f Table: 46920000 DAC: 00000017
Process swapper (pid: 0, stack limit = 0xc04d81b8)
Create the mapping upon startup from mxs_machine_init().
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add a call to of_clk_init() to register clocks defined in DT.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a999 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
|
|
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"These changes from 30 individual branches for the most part update
device tree files, but there are also a few source code changes that
have crept in this time, usually in order to atomically move over a
driver from using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (372 commits)
ARM: at91: dt: rm9200ek: add spi support
ARM: at91: dt: rm9200: add spi support
ARM: at91/DT: at91sam9n12: add SPI DMA client infos
ARM: at91/DT: sama5d3: add SPI DMA client infos
ARM: at91/DT: fix SPI compatibility string
ARM: Kirkwood: Fix the internal register ranges translation
ARM: dts: bcm281xx: change comment to C89 style
ARM: mmc: bcm281xx SDHCI driver (dt mods)
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
ARM: dts: omap5-uevm: Provide USB Host PHY clock frequency
ARM: dts: omap4-panda: Fix DVI EDID reads
ARM: dts: omap4-panda: Add USB Host support
arm: mvebu: enable mini-PCIe connectors on Armada 370 RD
ARM: shmobile: irqpin: add a DT property to enable masking on parent
ARM: dts: AM43x EPOS EVM support
ARM: dts: OMAP5: Add bandgap DT entry
ARM: dts: AM33XX: Add pinmux configuration for CPSW to am335x EVM
ARM: dts: AM33XX: Add pinmux configuration for CPSW to EVMsk
ARM: dts: AM33XX: Add pinmux configuration for CPSW to beaglebone
...
|
|
Instead of using a GPIO to turn on/off the CAN transceiver, it is better to
use a regulator as some systems may use a PMIC to power the CAN transceiver.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The CFA-10057 is a breakout board for the CFA-10036 that has Ethernet,
USB and a 4.3" LCD screen on it.
Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The CFA-10055 is yet another breakout board for the CFA-10036, and is
basically a CFA-10037, with the screen and LCD controller found on the
CFA-10049.
Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Using the soc bus infrastructure is helpful for reporting several SoC related
information such as: family, machine, SoC name and SoC revision.
$ cat /sys/bus/soc/devices/soc0/family
Freescale MXS Family
$ cat /sys/bus/soc/devices/soc0/machine
Freescale i.MX28 Evaluation Kit
$ cat /sys/bus/soc/devices/soc0/soc_id
i.MX28
$ cat /sys/bus/soc/devices/soc0/revision
TO1.2
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Commit ebafed7a ("ARM: irq: Call irqchip_init if no init_irq function is
specified") removed the need to explictly setup the init_irq field in
the machine description when using only irqchip_init. Remove that
declaration for mxs as well.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Now that the ARM core code calls debug_ll_io_init, we can remove it from
the machine_desc declaration.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
|
|
Move display timing configurations into device tree, so that the
auxdata for mxsfb driver can be killed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
With fec driver taking care of enet_out clk, most of board setup
do not need to enable enet_out clk. So remove them.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The device_initcall is not a friend of multiplatform build. Call
mxs_pm_init() as a machine_desc hook instead of device_initcall.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Most of the stuff in the headers are used nowhere now. Move a few
things that are useful for mach-mxs.c into there and remove the headers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Most of the function hooks are same between imx23 and imx28
machine_desc, so merge them into one.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
All three remaining functions declared in common.h are implemented by
clock driver. Create header include/linux/clk/mxs.h to contain them
and remove common.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
All the users of mxs_get_ocotp() are in mach-mxs.c. Move the function
into mach-mxs.c, make it a static function, and then remove ocotp.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The only user of the static mapping done in mx23_map_io and mx28_map_io
is low-level debug now. Use debug_ll_io_init() instead, so that the
static mapping is used nowhere and can be removed completely later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
There is no user of function mxs_reset_block() now. Let's move
mxs_restart() into mach-mxs.c as a static function and remove system.c
completely.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Move icoll.c into drivers/irqchip as irq-mxs.c, and along with the
renaming, change the driver to use IRQCHIP_DECLARE.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Select CLKSRC_OF and use clocksource_of_init() to initialize timer, so
that the call to mxs_timer_init() in clock driver can be removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The issue fixed by this patch manifests only then using X11
with mxsfb driver. The X11 will display either shifted image
or otherwise distorted image on the LCD.
The problem is that the X11 tries to reconfigure the framebuffer
and along the way calls fb_ops.fb_set_par() with X11's desired
configuration values. The field of particular interest is
fb_info->var.sync which contains non-standard values if
configured by kernel. These are either FB_SYNC_DATA_ENABLE_HIGH_ACT,
FB_SYNC_DOTCLK_FAILING_ACT or both, depending on the platform
configuration. Both of these values are defined in the
include/linux/mxsfb.h file.
The driver interprets these values and configures the LCD controller
accordingly. Yet X11 only has access to the standard values for this
field defined in include/uapi/linux/fb.h and thus, unlike kernel,
omits these special values. This results in distorted image on the
LCD.
This patch moves these non-standard values into new field of the
mxsfb_platform_data structure so the driver can in turn check this
field instead of the video mode field for these specific portions.
Moreover, this patch prefixes these values with MXSFB_SYNC_ prefix
instead of FB_SYNC_ prefix to prevent confusion of subsequent users.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Linux ARM <linux-arm-kernel@lists.infradead.org>
Cc: Linux FBDEV <linux-fbdev@vger.kernel.org>
Cc: Lothar Waßmann <LW@karo-electronics.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Commit 1fe42740 ("ARM: dts: mxs: Add the LCD to the 10049 board") seem
to have been applied with some fuzzyness, and the framebuffer
initialisation code for the CFA-10049 ended up in the CFA-10037
initialisation function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
into next/dt
From Shawn Guo:
mxs device tree changes for 3.9
- Mostly cfa100xx related device tree source updates
* tag 'mxs-dt-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: dts: Add rotary encoder to the CFA-10049
ARM: mxs: dts: Add gpio-keys for the rotary to the CFA-10049
ARM: dts: mxs: Add the LCD to the 10049 board
ARM: dts: mxs: Add muxing options for the third PWM
ARM: dts: cfa10049: Change the SPI3 bus to spi-gpio
ARM: mxs: dt: Add Crystalfontz CFA-10037 device tree support
ARM: mxs: Enable touchscreen on m28evk
ARM: dts: cfa10049: Add PCA9555 GPIO expander to the device tree
|
|
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The CFA-10037 is another expansion board for the CFA-10036 module, with
only a USB Host, a Ethernet device and a lot of gpios.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc update from Benjamin Herrenschmidt:
"The main highlight is probably some base POWER8 support. There's more
to come such as transactional memory support but that will wait for
the next one.
Overall it's pretty quiet, or rather I've been pretty poor at picking
things up from patchwork and reviewing them this time around and Kumar
no better on the FSL side it seems..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (73 commits)
powerpc+of: Rename and fix OF reconfig notifier error inject module
powerpc: mpc5200: Add a3m071 board support
powerpc/512x: don't compile any platform DIU code if the DIU is not enabled
powerpc/mpc52xx: use module_platform_driver macro
powerpc+of: Export of_reconfig_notifier_[register,unregister]
powerpc/dma/raidengine: add raidengine device
powerpc/iommu/fsl: Add PAMU bypass enable register to ccsr_guts struct
powerpc/mpc85xx: Change spin table to cached memory
powerpc/fsl-pci: Add PCI controller ATMU PM support
powerpc/86xx: fsl_pcibios_fixup_bus requires CONFIG_PCI
drivers/virt: the Freescale hypervisor driver doesn't need to check MSR[GS]
powerpc/85xx: p1022ds: Use NULL instead of 0 for pointers
powerpc: Disable relocation on exceptions when kexecing
powerpc: Enable relocation on during exceptions at boot
powerpc: Move get_longbusy_msecs into hvcall.h and remove duplicate function
powerpc: Add wrappers to enable/disable relocation on exceptions
powerpc: Add set_mode hcall
powerpc: Setup relocation on exceptions for bare metal systems
powerpc: Move initial mfspr LPCR out of __init_LPCR
powerpc: Add relocation on exception vector handlers
...
|
|
Add DTS file for this custom board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Rename the prom_*_property routines of the generic OF code to of_*_property.
This brings them in line with the naming used by the rest of the OF code.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Currently, the kernel unconditionally adds "local-mac-address" and
"mac-address" properties under both FEC ethernet DT nodes in case
the update_fec_mac_prop() function is called. These properties are
loaded with MAC address compiled from vendors OUI and a per-device
NIC saved in OCOTP storage.
Some more advanced bootloaders do augment the DT passed to the kernel
by these properties already. In such case, it is wrong for kernel to
override these values.
Adjust the FEC MAC address loading so that in case the DT properties
are already present in the DT passed from the bootloader, skip the
loading from OCOTP altogether. If the DT properties are not present,
load them from OCOTP.
Note that the later case will lead to zeroed out MAC address if OCOTP
is not programmed. This will lead to FEC not working at all.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The APF28 is a small SOM built around an i.MX28 processor with 128MBytes DDR2,
256MBytes NAND Flash and an Ethernet PHY.
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Pull ARM soc-specific updates, take 2 from Olof Johansson:
"This branch converts the MXS Freescale platform to use irqdomains and
sparse IRQ, in preparation for DT probing and multiplatform kernels."
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: remove mach/irqs.h
ARM: mxs: select SPARSE_IRQ
ARM: mxs: adopt irq_domain support for icoll driver
ARM: mxs: select MULTI_IRQ_HANDLER
ARM: mxs: retrieve timer irq from device tree
gpio/mxs: adopt irq_domain support for mxs gpio driver
|
|
Pull ARM soc device tree updates from Olof Johansson:
"Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8."
Trivial conflicts due to removal of vt8500 files, and one documentation
file that was added with slightly different contents both here and in
the USb tree.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (212 commits)
arm: vt8500: Fixup for missing gpio.h
ARM: LPC32xx: LED fix in PHY3250 DTS file
ARM: dt: mmp-dma: add binding file
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
ARM: tegra: Add Avionic Design Medcom-Wide support
ARM: tegra: Add Avionic Design Plutux support
ARM: tegra: Add Avionic Design Tamonten support
ARM: tegra: dts: Add pwm label
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
...
|
|
There is no such part as KS8001, KS8041 or KS8051. There are only
KSZ8001, KSZ8041 and KSZ8051. Rename these parts as such to match
the Micrel naming.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't load the FEC MAC address from OCOTP, but use the one supplied
via device tree by U-Boot. This is the preferred way, every DT-capable
bootloader does set up "mac-address" and "local-mac-address" properties
into the DT passed to the kernel.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Remove irq_domain_add_legacy call from mach-mxs.c and have icoll adopt
irq_domain support in the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
As part of multi-platform effort, let's enable MULTI_IRQ_HANDLER for
mach-mxs and remove entry-macro.S.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
