| Age | Commit message (Collapse) | Author |
|---|
|
The data patterns should allow us to easily tell if somebody accesses
initdata/code after it was freed. Same code as on various other
architectures.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Size zones and holes in an architecture independent manner for s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Virtual memmap support for s390. Inspired by the ia64 implementation.
Unlike ia64 we need a mechanism which allows us to dynamically attach
shared memory regions.
These memory regions are accessed via the dcss device driver. dcss
implements the 'direct_access' operation, which requires struct pages
for every single shared page.
Therefore this implementation provides an interface to attach/detach
shared memory:
int add_shared_memory(unsigned long start, unsigned long size);
int remove_shared_memory(unsigned long start, unsigned long size);
The purpose of the add_shared_memory function is to add the given
memory range to the 1:1 mapping and to make sure that the
corresponding range in the vmemmap is backed with physical pages.
It also initialises the new struct pages.
remove_shared_memory in turn only invalidates the page table
entries in the 1:1 mapping. The page tables and the memory used for
struct pages in the vmemmap are currently not freed. They will be
reused when the next segment will be attached.
Given that the maximum size of a shared memory region is 2GB and
in addition all regions must reside below 2GB this is not too much of
a restriction, but there is room for improvement.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Commit 7676bef9c183fd573822cac9992927ef596d584c breaks DCSS support on
s390. DCSS needs initialized struct pages to work. With the usage of
add_active_range() only the struct pages for physically present pages
are initialized.
This could be fixed if the DCSS driver would initiliaze the struct pages
itself, but this doesn't work too. This is because the mem_map array
does not include holes after the last present memory area and therefore
there is nothing that could be initialized.
To fix this and to avoid some dirty hacks revert this patch for now.
Will be added later when we move to a virtual mem_map.
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use page_to_phys and pfn_to_page to avoid open-coded mem_map usage.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Size zones and holes in an architecture independent manner for s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Major cleanup of all s390 inline assemblies. They now have a common
coding style. Quite a few have been shortened, mainly by using register
asm variables. Use of the EX_TABLE macro helps as well. The atomic ops,
bit ops and locking inlines new use the Q-constraint if a newer gcc
is used. That results in slightly better code.
Thanks to Christian Borntraeger for proof reading the changes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Changed and simplified some page table related #defines and code.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Don't waste DMA capable pages for identity mapping page tables.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Put s390's syscall tables into .rodata section and write protect this
section to prevent misuse of it. Suggested by Arjan van de Ven
<arjan@infradead.org>.
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Sanitize some s390 Kconfig options. We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT. Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The memory setup didn't take care of memory holes and this makes the memory
management think there would be more memory available than there is in
reality. That causes the OOM killer to kill processes even if there is enough
memory left that can be written to the swap space.
The patch fixes this by using free_area_init_node with an array of memory
holes instead of free_area_init. Further the patch cleans up the code in
setup.c by splitting setup_arch into smaller pieces.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
