| Age | Commit message (Expand) | Author |
|---|
| 2013-02-13 | sabrelite: mipi camera, turn on pwm3 | Troy Kisky |
| 2013-02-13 | pwm: add high_perf clock option, fix rounding | Troy Kisky |
| 2013-02-13 | mx6_sabrelite: setup J12 as CSI1 | Troy Kisky |
| 2013-02-12 | pcie: add MSI support | Troy Kisky |
| 2013-02-12 | pcie: fix legacy interrupts for bridge | Troy Kisky |
| 2013-02-12 | pcie: fix bridge access and bus 1 access | Troy Kisky |
| 2013-02-12 | pcie: force gen1 speed | Troy Kisky |
| 2013-02-12 | mx6qsabrelite: export buttons as GPIO if no KEYBOARD_GPIO | Eric Nelson |
| 2013-02-12 | nitrogen6x_defconfig: Add NAPI to match Freescale config, prevent network ins... | Eric Nelson |
| 2013-02-12 | nitrogen6x_defconfig: sync with latest Kconfig defaults | Eric Nelson |
| 2013-02-12 | nitrogen6x_defconfig: remove unsupported cameras | Eric Nelson |
| 2013-02-12 | Nitrogen6 SOM: mipi | Troy Kisky |
| 2013-02-12 | mx6q_sabrelite: add mx6solo/mx6duallite support | Troy Kisky |
| 2013-02-12 | board-mx6q_sabrelite: detect Flexcan controller chip | Troy Kisky |
| 2013-02-12 | i.MX6: mx6qsabrelite: add weak pull-up on RGB touch screen interrupt line (GP... | Eric Nelson |
| 2013-02-12 | nitrogen6x_defconfig: sync with non-Android settings | Eric Nelson |
| 2013-02-12 | i.MX6: mx6q_sabrelite: add vwl1271 regulator | Eric Nelson |
| 2013-02-12 | i.MX6: mx6q_sabre_lite: add wl1271 interface on ESDHC2 | Eric Nelson |
| 2013-02-12 | i.MX6: mx6q_sabrelite: add SD2+WiFi pad setup | Eric Nelson |
| 2013-02-12 | nitrogen6x_defconfig: add supported hardware/features | Eric Nelson |
| 2013-02-12 | i.MX6: mx6q_sabrelite: Add support for FocalTech ft5x06 driver | Eric Nelson |
| 2013-02-12 | i.MX6Q: mx6q_sabrelite: Add TSC2004 touch screen support | Eric Nelson |
| 2013-02-12 | i.MX6: mx6q_sabrelite: Sabre Lite doesn't expose UART3, Nitrogen6W does | Eric Nelson |
| 2013-02-12 | i.MX6: mx6q_sabrelite: set up UART3 (/dev/ttymxc2) with RTS, CTS on pins EIM_... | Eric Nelson |
| 2013-02-12 | i.MX6Q: mx6q_sabrelite: fix SDHC write-protect pins | Eric Nelson |
| 2013-02-12 | i.MX6: mx6q_sabrelite: route SGTL5000 to audmux 3 on Nitrogen6 | Eric Nelson |
| 2013-02-12 | i.MX6: mx6q_sabrelite: Add Nitrogen6W detection | Eric Nelson |
| 2013-02-12 | i.MX6: mx6q_sabrelite: swap SD cards to have numbering match U-Boot | Eric Nelson |
| 2013-02-12 | mx6qsabrelite: move HDMI to IPU0/DI1 to separate it from the parallel RGB dis... | Eric Nelson |
| 2013-02-12 | i.MX6Q: mx6q_sabrelite: Add PWM0 backlight (on DRGB connector) | Eric Nelson |
| 2013-02-12 | i.MX6: mx6q_sabrelite: add DVFS, MIPI_CSI2, PCIE, PERFMON to automatic Sabre-... | Eric Nelson |
| 2013-02-12 | mx6q_sabrelite: add pcie support | Eric Nelson |
| 2013-02-12 | i.MX6: mx6q_sabrelite: set MTD size for SPI Nor to match U-Boot | Eric Nelson |
| 2013-02-12 | mmc: esdhc: add caps flag to esdhc_platform_data | Troy Kisky |
| 2013-02-12 | sabrelite: allow gigabit, 0 tx delay, set phy irq | Troy Kisky |
| 2013-02-12 | fix execute permissions | Troy Kisky |
| 2013-02-12 | ENGR00241003-1 mx6: need to add delay in LDO voltage setting | Anson Huang |
| 2012-12-12 | ENGR00235817 mx6: use SNVS LPGPR register to store boot mode value. | Zhang Jiejing |
| 2012-12-12 | ENGR00236031 MX6 USB :Change default USB H1 and OTG driver load order | make shi |
| 2012-12-05 | ENGR00235624 Quad/DualLite ARD: MTD partition non aligned | Alejandro Sierra |
| 2012-12-05 | ENGR00235630 MX6 USB :fix USB does not work when plug in device during suspend | make shi |
| 2012-11-29 | ENGR00235268: change caam_ipg_clk's CG to CG6 | Terry Lv |
| 2012-11-29 | ENGR00235081 Quad DL: Fix chip select for SPI-NOR and flags | Alejandro Sierra |
| 2012-11-28 | ENGR00234685-2 mx6q_sabreauto: change Sabreauto board to LDO-ENABLED mode | Robin Gong |
| 2012-11-28 | ENGR00234685-1 cpufreq:fix one bug in cpufreq driver if I2C transfer error | Robin Gong |
| 2012-11-28 | ENGR00234531 fix MFGTOOL issue after USB module loadable done | Tony LIU |
| 2012-11-28 | ENGR00234411-2 CPUFREQ: fix one code bug on regulator restore when fail | Robin Gong |
| 2012-11-28 | ENGR00234411-1 Sabreauto: fix error print COULD NOT SET GP VOLTAGE. | Robin Gong |
| 2012-11-28 | ENGR00234354-2: board-mx6q_sabreauto aline weim-nor partition layout | Adrian Alonso |
| 2012-11-28 | ENGR00234354-1: board-mx6q_sabreauto aline spi-nor partition layout | Adrian Alonso |
