| Age | Commit message (Collapse) | Author |
|---|
|
Disable wireless drivers and cfg80211 module to avoid conflicts
with backported drivers.
Related-to: ELB-2724
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Disabling all wireless drivers and cfg80211 module to avoid conflicts
with backported drivers.
Related-to: ELB-2724
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Enable WIRELESS_EXT, WEXT_PRIV and MODULE_SIG options as needed for
the backports-5.4.
Related-to: ELB-2724
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
As suggested by the reference manual in a note in chapter 13.2
this commit disables the keeper and enables a 100k pull-down on the
adc pins.
Related-to: ELB-2690
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
(cherry picked from commit d5a3675860d03d783689de3ed7cb3dec27e6a155)
|
|
The correct spelling for the property is gpios, otherwise the regulator
will neither reserve nor control any gpio(s).
Thus any SD/MMC card which can use UHS 1 modes will fail.
Related-to: #46566
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
This takes the mainline part that adds the wifi chip. This patch
solves the issue that exists when resuming from suspend.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Specify the start dealy cell point when send first CMD19
in tuning procedure. This fixes these tunning procedure issues, and
lets to use UHS-I mode properly:
sdhci: Tuning procedure failed, falling back to fixed sampling clock
mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900,
card status 0xb00
Fixes: http://redmine.toradex.int/issues/46566
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
|
|
Add the stmpe-adc DT node as found on Toradex iMX6 modules
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
- add recovery mode for applicable i2c buses for
Colibri iMX7 module.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
- fix the name of pinctrl set for i2c2 recovery mode;
- add recovery mode for applicable i2c buses for
Apalis/Colibri iMX6Q/D/DL modules.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Related to: #49059
|
|
Commit 41ec065fc5841 fixes ecspi sdma script type for spi1-4 only.
Commit df07101e1c4a2 sets wrong type of sdma script for SPI5.
The workaroud sdma script NOT work in SPBA bus, so return back
the correct sdma script type for spi5.
Related to: #48675
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
toradex_4.9-2.3.x-imx-next
|
|
This is the 4.9.166 stable release
|
|
I don't know where that mcp258x came from but it really is a mcp2515.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
commit 6f44a0bacb79a03972c83759711832b382b1b8ac upstream.
In current die(), the irq is disabled for __die() handle, not
including the possible panic() handling. Since the log in __die()
can take several hundreds ms, new irq might come and interrupt
current die().
If the process calling die() holds some critical resource, and some
other process scheduled later also needs it, then it would deadlock.
The first panic will not be executed.
So here disable irq for the whole flow of die().
Signed-off-by: Qiao Zhou <qiaozhou@asrmicro.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 47c25036b60f27b86ab44b66a8861bcf81cde39b upstream.
Insert Branch instruction instead of NOP to make sure assembler don't
patch code in forbidden slot. In jump label function, it might
be possible to patch Control Transfer Instructions(CTIs) into
forbidden slot, which will generate Reserved Instruction exception
in MIPS release 6.
Signed-off-by: Archer Yan <ayan@wavecomp.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
[paul.burton@mips.com:
- Add MIPS prefix to subject.
- Mark for stable from v4.0, which introduced r6 support, onwards.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3f0a53bc6482fb09770982a8447981260ea258dc upstream.
This fixes booting with the combination of CONFIG_RELOCATABLE=y
and CONFIG_MIPS_ELF_APPENDED_DTB=y.
Sections that appear after the relocation table are not relocated
on system boot (except .bss, which has special handling).
With CONFIG_MIPS_ELF_APPENDED_DTB, the dtb is part of the
vmlinux ELF, so it must be relocated together with everything else.
Fixes: 069fd766271d ("MIPS: Reserve space for relocation table")
Signed-off-by: Yasha Cherikovsky <yasha.che3@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5f5f67da9781770df0403269bc57d7aae608fecd upstream.
Timekeeping IRQs from CS5536 MFGPT are routed to i8259, which then
triggers the "cascade" IRQ on MIPS CPU. Without IRQF_NO_SUSPEND in
cascade_irqaction, MFGPT interrupts will be masked in suspend mode,
and the machine would be unable to resume once suspended.
Previously, MIPS IRQs were not disabled properly, so the original
code appeared to work. Commit a3e6c1eff5 ("MIPS: IRQ: Fix disable_irq on
CPU IRQs") uncovers the bug. To fix it, add IRQF_NO_SUSPEND to
cascade_irqaction.
This commit is functionally identical to 0add9c2f1cff ("MIPS:
Loongson-3: Add IRQF_NO_SUSPEND to Cascade irqaction"), but it forgot
to apply the same fix to Loongson2.
Signed-off-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bbeac2830f4de270bb48141681cb730aadf8dce1 upstream.
Reported by syzkaller:
The kvm-intel.unrestricted_guest=0
WARNING: CPU: 5 PID: 1014 at /home/kernel/data/kvm/arch/x86/kvm//x86.c:7227 kvm_arch_vcpu_ioctl_run+0x38b/0x1be0 [kvm]
CPU: 5 PID: 1014 Comm: warn_test Tainted: G W OE 4.13.0-rc3+ #8
RIP: 0010:kvm_arch_vcpu_ioctl_run+0x38b/0x1be0 [kvm]
Call Trace:
? put_pid+0x3a/0x50
? rcu_read_lock_sched_held+0x79/0x80
? kmem_cache_free+0x2f2/0x350
kvm_vcpu_ioctl+0x340/0x700 [kvm]
? kvm_vcpu_ioctl+0x340/0x700 [kvm]
? __fget+0xfc/0x210
do_vfs_ioctl+0xa4/0x6a0
? __fget+0x11d/0x210
SyS_ioctl+0x79/0x90
entry_SYSCALL_64_fastpath+0x23/0xc2
? __this_cpu_preempt_check+0x13/0x20
The syszkaller folks reported a residual mmio emulation request to userspace
due to vm86 fails to emulate inject real mode interrupt(fails to read CS) and
incurs a triple fault. The vCPU returns to userspace with vcpu->mmio_needed == true
and KVM_EXIT_SHUTDOWN exit reason. However, the syszkaller testcase constructs
several threads to launch the same vCPU, the thread which lauch this vCPU after
the thread whichs get the vcpu->mmio_needed == true and KVM_EXIT_SHUTDOWN will
trigger the warning.
#define _GNU_SOURCE
#include <pthread.h>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <sys/wait.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/mman.h>
#include <fcntl.h>
#include <unistd.h>
#include <linux/kvm.h>
#include <stdio.h>
int kvmcpu;
struct kvm_run *run;
void* thr(void* arg)
{
int res;
res = ioctl(kvmcpu, KVM_RUN, 0);
printf("ret1=%d exit_reason=%d suberror=%d\n",
res, run->exit_reason, run->internal.suberror);
return 0;
}
void test()
{
int i, kvm, kvmvm;
pthread_t th[4];
kvm = open("/dev/kvm", O_RDWR);
kvmvm = ioctl(kvm, KVM_CREATE_VM, 0);
kvmcpu = ioctl(kvmvm, KVM_CREATE_VCPU, 0);
run = (struct kvm_run*)mmap(0, 4096, PROT_READ|PROT_WRITE, MAP_SHARED, kvmcpu, 0);
srand(getpid());
for (i = 0; i < 4; i++) {
pthread_create(&th[i], 0, thr, 0);
usleep(rand() % 10000);
}
for (i = 0; i < 4; i++)
pthread_join(th[i], 0);
}
int main()
{
for (;;) {
int pid = fork();
if (pid < 0)
exit(1);
if (pid == 0) {
test();
exit(0);
}
int status;
while (waitpid(pid, &status, __WALL) != pid) {}
}
return 0;
}
This patch fixes it by resetting the vcpu->mmio_needed once we receive
the triple fault to avoid the residue.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Zubin Mithra <zsm@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34333cc6c2cb021662fd32e24e618d1b86de95bf upstream.
Regarding segments with a limit==0xffffffff, the SDM officially states:
When the effective limit is FFFFFFFFH (4 GBytes), these accesses may
or may not cause the indicated exceptions. Behavior is
implementation-specific and may vary from one execution to another.
In practice, all CPUs that support VMX ignore limit checks for "flat
segments", i.e. an expand-up data or code segment with base=0 and
limit=0xffffffff. This is subtly different than wrapping the effective
address calculation based on the address size, as the flat segment
behavior also applies to accesses that would wrap the 4g boundary, e.g.
a 4-byte access starting at 0xffffffff will access linear addresses
0xffffffff, 0x0, 0x1 and 0x2.
Fixes: f9eb4af67c9d ("KVM: nVMX: VMX instructions: add checks for #GP/#SS exceptions")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 946c522b603f281195af1df91837a1d4d1eb3bc9 upstream.
The VMCS.EXIT_QUALIFCATION field reports the displacements of memory
operands for various instructions, including VMX instructions, as a
naturally sized unsigned value, but masks the value by the addr size,
e.g. given a ModRM encoded as -0x28(%ebp), the -0x28 displacement is
reported as 0xffffffd8 for a 32-bit address size. Despite some weird
wording regarding sign extension, the SDM explicitly states that bits
beyond the instructions address size are undefined:
In all cases, bits of this field beyond the instruction’s address
size are undefined.
Failure to sign extend the displacement results in KVM incorrectly
treating a negative displacement as a large positive displacement when
the address size of the VMX instruction is smaller than KVM's native
size, e.g. a 32-bit address size on a 64-bit KVM.
The very original decoding, added by commit 064aea774768 ("KVM: nVMX:
Decoding memory operands of VMX instructions"), sort of modeled sign
extension by truncating the final virtual/linear address for a 32-bit
address size. I.e. it messed up the effective address but made it work
by adjusting the final address.
When segmentation checks were added, the truncation logic was kept
as-is and no sign extension logic was introduced. In other words, it
kept calculating the wrong effective address while mostly generating
the correct virtual/linear address. As the effective address is what's
used in the segment limit checks, this results in KVM incorreclty
injecting #GP/#SS faults due to non-existent segment violations when
a nested VMM uses negative displacements with an address size smaller
than KVM's native address size.
Using the -0x28(%ebp) example, an EBP value of 0x1000 will result in
KVM using 0x100000fd8 as the effective address when checking for a
segment limit violation. This causes a 100% failure rate when running
a 32-bit KVM build as L1 on top of a 64-bit KVM L0.
Fixes: f9eb4af67c9d ("KVM: nVMX: VMX instructions: add checks for #GP/#SS exceptions")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e2477233145f2156434afb799583bccd878f3e9f upstream.
Fix boolean expressions by using logical AND operator '&&' instead of
bitwise operator '&'.
This issue was detected with the help of Coccinelle.
Fixes: 4fa084af28ca ("ARM: OSIRIS: DVS (Dynamic Voltage Scaling) supoort.")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
[krzk: Fix -Wparentheses warning]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca6d5149d2ad0a8d2f9c28cbe379802260a0a5e0 upstream.
GCC 8 warns about the logic in vr_get/set(), which with -Werror breaks
the build:
In function ‘user_regset_copyin’,
inlined from ‘vr_set’ at arch/powerpc/kernel/ptrace.c:628:9:
include/linux/regset.h:295:4: error: ‘memcpy’ offset [-527, -529] is
out of the bounds [0, 16] of object ‘vrsave’ with type ‘union
<anonymous>’ [-Werror=array-bounds]
arch/powerpc/kernel/ptrace.c: In function ‘vr_set’:
arch/powerpc/kernel/ptrace.c:623:5: note: ‘vrsave’ declared here
} vrsave;
This has been identified as a regression in GCC, see GCC bug 88273.
However we can avoid the warning and also simplify the logic and make
it more robust.
Currently we pass -1 as end_pos to user_regset_copyout(). This says
"copy up to the end of the regset".
The definition of the regset is:
[REGSET_VMX] = {
.core_note_type = NT_PPC_VMX, .n = 34,
.size = sizeof(vector128), .align = sizeof(vector128),
.active = vr_active, .get = vr_get, .set = vr_set
},
The end is calculated as (n * size), ie. 34 * sizeof(vector128).
In vr_get/set() we pass start_pos as 33 * sizeof(vector128), meaning
we can copy up to sizeof(vector128) into/out-of vrsave.
The on-stack vrsave is defined as:
union {
elf_vrreg_t reg;
u32 word;
} vrsave;
And elf_vrreg_t is:
typedef __vector128 elf_vrreg_t;
So there is no bug, but we rely on all those sizes lining up,
otherwise we would have a kernel stack exposure/overwrite on our
hands.
Rather than relying on that we can pass an explict end_pos based on
the sizeof(vrsave). The result should be exactly the same but it's
more obviously not over-reading/writing the stack and it avoids the
compiler warning.
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Mathieu Malaterre <malat@debian.org>
Cc: stable@vger.kernel.org
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fe1ef6bcdb4fca33434256a802a3ed6aacf0bd2f upstream.
Commit 8792468da5e1 "powerpc: Add the ability to save FPU without
giving it up" unexpectedly removed the MSR_FE0 and MSR_FE1 bits from
the bitmask used to update the MSR of the previous thread in
__giveup_fpu() causing a KVM-PR MacOS guest to lockup and panic the
host kernel.
Leaving FE0/1 enabled means unrelated processes might receive FPEs
when they're not expecting them and crash. In particular if this
happens to init the host will then panic.
eg (transcribed):
qemu-system-ppc[837]: unhandled signal 8 at 12cc9ce4 nip 12cc9ce4 lr 12cc9ca4 code 0
systemd[1]: unhandled signal 8 at 202f02e0 nip 202f02e0 lr 001003d4 code 0
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Reinstate these bits to the MSR bitmask to enable MacOS guests to run
under 32-bit KVM-PR once again without issue.
Fixes: 8792468da5e1 ("powerpc: Add the ability to save FPU without giving it up")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 36da5ff0bea2dc67298150ead8d8471575c54c7d upstream.
The 83xx has 8 SPRG registers and uses at least SPRG4
for DTLB handling LRU.
Fixes: 2319f1239592 ("powerpc/mm: e300c2/c3/c4 TLB errata workaround")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b62f9bd2246b7d3d086e571397c14ba52645ef1 upstream.
Currently the opal log is globally readable. It is kernel policy to
limit the visibility of physical addresses / kernel pointers to root.
Given this and the fact the opal log may contain this information it
would be better to limit the readability to root.
Fixes: bfc36894a48b ("powerpc/powernv: Add OPAL message log interface")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Reviewed-by: Stewart Smith <stewart@linux.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d183ca8baec983dc4208ca45ece3c36763df912 upstream.
'nobats' kernel parameter or some options like CONFIG_DEBUG_PAGEALLOC
deny the use of BATS for mapping memory.
This patch makes sure that the specific wii RAM mapping function
takes it into account as well.
Fixes: de32400dd26e ("wii: use both mem1 and mem2 as ram")
Cc: stable@vger.kernel.org
Reviewed-by: Jonathan Neuschafer <j.neuschaefer@gmx.net>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9580b71b5a7863c24a9bd18bcd2ad759b86b1eff upstream.
Clear the on-stack STACK_FRAME_REGS_MARKER on exception exit in order
to avoid confusing stacktrace like the one below.
Call Trace:
[c0e9dca0] [c01c42a0] print_address_description+0x64/0x2bc (unreliable)
[c0e9dcd0] [c01c4684] kasan_report+0xfc/0x180
[c0e9dd10] [c0895130] memchr+0x24/0x74
[c0e9dd30] [c00a9e38] msg_print_text+0x124/0x574
[c0e9dde0] [c00ab710] console_unlock+0x114/0x4f8
[c0e9de40] [c00adc60] vprintk_emit+0x188/0x1c4
--- interrupt: c0e9df00 at 0x400f330
LR = init_stack+0x1f00/0x2000
[c0e9de80] [c00ae3c4] printk+0xa8/0xcc (unreliable)
[c0e9df20] [c0c27e44] early_irq_init+0x38/0x108
[c0e9df50] [c0c15434] start_kernel+0x310/0x488
[c0e9dff0] [00003484] 0x3484
With this patch the trace becomes:
Call Trace:
[c0e9dca0] [c01c42c0] print_address_description+0x64/0x2bc (unreliable)
[c0e9dcd0] [c01c46a4] kasan_report+0xfc/0x180
[c0e9dd10] [c0895150] memchr+0x24/0x74
[c0e9dd30] [c00a9e58] msg_print_text+0x124/0x574
[c0e9dde0] [c00ab730] console_unlock+0x114/0x4f8
[c0e9de40] [c00adc80] vprintk_emit+0x188/0x1c4
[c0e9de80] [c00ae3e4] printk+0xa8/0xcc
[c0e9df20] [c0c27e44] early_irq_init+0x38/0x108
[c0e9df50] [c0c15434] start_kernel+0x310/0x488
[c0e9dff0] [00003484] 0x3484
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 28713169d879b67be2ef2f84dcf54905de238294 upstream.
This patch fixes a build failure when using GCC 8.1:
/usr/bin/ld: block/partitions/ldm.o: in function `ldm_parse_tocblock':
block/partitions/ldm.c:153: undefined reference to `strcmp'
This is caused by a new optimization which effectively replaces a
strncmp() call with a strcmp() call. This affects a number of strncmp()
call sites in the kernel.
The entire class of optimizations is avoided with -fno-builtin, which
gets enabled by -ffreestanding. This may avoid possible future build
failures in case new optimizations appear in future compilers.
I haven't done any performance measurements with this patch but I did
count the function calls in a defconfig build. For example, there are now
23 more sprintf() calls and 39 fewer strcpy() calls. The effect on the
other libc functions is smaller.
If this harms performance we can tackle that regression by optimizing
the call sites, ideally using semantic patches. That way, clang and ICC
builds might benfit too.
Cc: stable@vger.kernel.org
Reference: https://marc.info/?l=linux-m68k&m=154514816222244&w=2
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eaf46edf6ea89675bd36245369c8de5063a0272c upstream.
The NEON MAC calculation routine fails to handle the case correctly
where there is some data in the buffer, and the input fills it up
exactly. In this case, we enter the loop at the end with w8 == 0,
while a negative value is assumed, and so the loop carries on until
the increment of the 32-bit counter wraps around, which is quite
obviously wrong.
So omit the loop altogether in this case, and exit right away.
Reported-by: Eric Biggers <ebiggers@kernel.org>
Fixes: a3fd82105b9d1 ("arm64/crypto: AES in CCM mode using ARMv8 Crypto ...")
Cc: stable@vger.kernel.org
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d5e3c55e01d8b1774b37b4647c30fb22f1d39077 ]
Newer ARC gcc handles lp_start, lp_end in a different way and doesn't
like them in the clobber list.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f8a15f97664178f27dfbf86a38f780a532cb6df0 ]
ARCv2 optimized memcpy uses PREFETCHW instruction for prefetching the
next cache line but doesn't ensure that the line is not past the end of
the buffer. PRETECHW changes the line ownership and marks it dirty,
which can cause data corruption if this area is used for DMA IO.
Fix the issue by avoiding the PREFETCHW. This leads to performance
degradation but it is OK as we'll introduce new memcpy implementation
optimized for unaligned memory access using.
We also cut off all PREFETCH instructions at they are quite useless
here:
* we call PREFETCH right before LOAD instruction call.
* we copy 16 or 32 bytes of data (depending on CONFIG_ARC_HAS_LL64)
in a main logical loop. so we call PREFETCH 4 times (or 2 times)
for each L1 cache line (in case of 64B L1 cache Line which is
default case). Obviously this is not optimal.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 74698f6971f25d045301139413578865fc2bd8f9 ]
Updates to the GIC architecture allow ID_AA64PFR0_EL1.GIC to have
values other than 0 or 1. At the moment, Linux is quite strict in the
way it handles this field at early boot stage (cpufeature is fine) and
will refuse to use the system register CPU interface if it doesn't
find the value 1.
Fixes: 021f653791ad17e03f98aaa7fb933816ae16f161 ("irqchip: gic-v3: Initial support for GICv3")
Reported-by: Chase Conklin <Chase.Conklin@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1b5ba350784242eb1f899bcffd95d2c7cff61e84 ]
Arm TC2 fails cpu hotplug stress test.
This issue was tracked down to a missing copy of the new affinity
cpumask for the vexpress-spc interrupt into struct
irq_common_data.affinity when the interrupt is migrated in
migrate_one_irq().
Fix it by replacing the arm specific hotplug cpu migration with the
generic irq code.
This is the counterpart implementation to commit 217d453d473c ("arm64:
fix a migrating irq bug when hotplug cpu").
Tested with cpu hotplug stress test on Arm TC2 (multi_v7_defconfig plus
CONFIG_ARM_BIG_LITTLE_CPUFREQ=y and CONFIG_ARM_VEXPRESS_SPC_CPUFREQ=y).
The vexpress-spc interrupt (irq=22) on this board is affine to CPU0.
Its affinity cpumask now changes correctly e.g. from 0 to 1-4 when
CPU0 is hotplugged out.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
uninitialized
[ Upstream commit dc30e70391376ba3987aeb856ae6d9c0706534f1 ]
In function omap4_dsi_mux_pads(), local variable "reg" could
be uninitialized if function regmap_read() returns -EINVAL.
However, it will be used directly in the later context, which
is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Provide proper configuration for VGEN3, to make sure it's is always powered
which allows that rail to be automatically switched to 1.8 volts
for proper UHS-I operation. By default it's disabled.
With UHS-I enabled:
[ 104.153898] mmc1: new ultra high speed SDR104 SDHC card at address 59b4
[ 104.166202] mmcblk1: mmc1:59b4 USD00 15.0 GiB
[ 104.173923] mmcblk1: p1
root@colibri-imx6:~# hdparm -t /dev/mmcblk1
/dev/mmcblk1:
Timing buffered disk reads: 226 MB in 3.01 seconds = 75.01 MB/sec
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
|
|
commit f764c58b7faa26f5714e6907f892abc2bc0de4f8 upstream.
Guenter reported a build warning for CONFIG_CPU_SUP_INTEL=n:
> With allmodconfig-CONFIG_CPU_SUP_INTEL, this patch results in:
>
> In file included from arch/x86/events/amd/core.c:8:0:
> arch/x86/events/amd/../perf_event.h:1036:45: warning: ‘struct cpu_hw_event’ declared inside parameter list will not be visible outside of this definition or declaration
> static inline int intel_cpuc_prepare(struct cpu_hw_event *cpuc, int cpu)
While harmless (an unsed pointer is an unused pointer, no matter the type)
it needs fixing.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: d01b1f96a82e ("perf/x86/intel: Make cpuc allocations consistent")
Link: http://lkml.kernel.org/r/20190315081410.GR5996@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52f64909409c17adf54fcf5f9751e0544ca3a6b4 upstream
Skylake systems will receive a microcode update to address a TSX
errata. This microcode will (by default) clobber PMC3 when TSX
instructions are (speculatively or not) executed.
It also provides an MSR to cause all TSX transaction to abort and
preserve PMC3.
Add the CPUID enumeration and MSR definition.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 11f8b2d65ca9029591c8df26bb6bd063c312b7fe upstream
Such that we can re-use it.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d01b1f96a82e5dd7841a1d39db3abfdaf95f70ab upstream
The cpuc data structure allocation is different between fake and real
cpuc's; use the same code to init/free both.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Exynos5420
commit 28928a3ce142b2e4e5a7a0f067cefb41a3d2c3f9 upstream.
In Odroid XU3 Lite board, the temperature levels reported for thermal
zone 0 were weird. In warm room:
/sys/class/thermal/thermal_zone0/temp:32000
/sys/class/thermal/thermal_zone1/temp:51000
/sys/class/thermal/thermal_zone2/temp:55000
/sys/class/thermal/thermal_zone3/temp:54000
/sys/class/thermal/thermal_zone4/temp:51000
Sometimes after booting the value was even equal to ambient temperature
which is highly unlikely to be a real temperature of sensor in SoC.
The thermal sensor's calibration (trimming) is based on fused values.
In case of the board above, the fused values are: 35, 52, 43, 58 and 43
(corresponding to each TMU device). However driver defined a minimum value
for fused data as 40 and for smaller values it was using a hard-coded 55
instead. This lead to mapping data from sensor to wrong temperatures
for thermal zone 0.
Various vendor 3.10 trees (Hardkernel's based on Samsung LSI, Artik 10)
do not impose any limits on fused values. Since we do not have any
knowledge about these limits, use 0 as a minimum accepted fused value.
This should essentially allow accepting any reasonable fused value thus
behaving like vendor driver.
The exynos5420-tmu-sensor-conf.dtsi is copied directly from existing
exynos4412 with one change - the samsung,tmu_min_efuse_value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit afc9f65e01cd114cb2cedf544d22239116ce0cc6 ]
When building the kernel as Thumb-2 with binutils 2.29 or newer, if the
assembler has seen the .type directive (via ENDPROC()) for a symbol, it
automatically handles the setting of the lowest bit when the symbol is
used with ADR. The badr macro on the other hand handles this lowest bit
manually. This leads to a jump to a wrong address in the wrong state
in the syscall return path:
Internal error: Oops - undefined instruction: 0 [#2] SMP THUMB2
Modules linked in:
CPU: 0 PID: 652 Comm: modprobe Tainted: G D 4.18.0-rc3+ #8
PC is at ret_fast_syscall+0x4/0x62
LR is at sys_brk+0x109/0x128
pc : [<80101004>] lr : [<801c8a35>] psr: 60000013
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 50c5387d Table: 9e82006a DAC: 00000051
Process modprobe (pid: 652, stack limit = 0x(ptrval))
80101000 <ret_fast_syscall>:
80101000: b672 cpsid i
80101002: f8d9 2008 ldr.w r2, [r9, #8]
80101006: f1b2 4ffe cmp.w r2, #2130706432 ; 0x7f000000
80101184 <local_restart>:
80101184: f8d9 a000 ldr.w sl, [r9]
80101188: e92d 0030 stmdb sp!, {r4, r5}
8010118c: f01a 0ff0 tst.w sl, #240 ; 0xf0
80101190: d117 bne.n 801011c2 <__sys_trace>
80101192: 46ba mov sl, r7
80101194: f5ba 7fc8 cmp.w sl, #400 ; 0x190
80101198: bf28 it cs
8010119a: f04f 0a00 movcs.w sl, #0
8010119e: f3af 8014 nop.w {20}
801011a2: f2af 1ea2 subw lr, pc, #418 ; 0x1a2
To fix this, add a new symbol name which doesn't have ENDPROC used on it
and use that with badr. We can't remove the badr usage since that would
would cause breakage with older binutils.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a66352e005488ecb4b534ba1af58a9f671eba9b8 upstream.
Add minimal parameters needed by the Exynos CLKOUT driver to Exynos3250
PMU node. This fixes the following warning on boot:
exynos_clkout_init: failed to register clkout clock
Fixes: d19bb397e19e ("ARM: dts: exynos: Update PMU node with CLKOUT related data")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ec33745bccc8f336957c751f4153421cc9ef5a54 upstream.
Commit 225da7e65a03 ("ARM: dts: add eMMC reset line for
exynos4412-odroid-common") added MMC power sequence for eMMC card of
Odroid X2/U3. It reused generic sd1_cd pin control configuration node
and only disabled pull-up. However that time the pinctrl configuration
was not applied during MMC power sequence driver initialization. This
has been changed later by commit d97a1e5d7cd2 ("mmc: pwrseq: convert to
proper platform device").
It turned out then, that the provided pinctrl configuration is not
correct, because the eMMC_RTSN line is being re-configured as 'special
function/card detect function for mmc1 controller' not the simple
'output', thus the power sequence driver doesn't really set the pin
value. This in effect broke the reboot of Odroid X2/U3 boards. Fix this
by providing separate node with eMMC_RTSN pin configuration.
Cc: <stable@vger.kernel.org>
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 225da7e65a03 ("ARM: dts: add eMMC reset line for exynos4412-odroid-common")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2b424cfc69728224fcb5fad138ea7260728e0901 ]
Patch (b6c7a324df37b "MIPS: Fix get_frame_info() handling of
microMIPS function size.") introduces additional function size
check for microMIPS by only checking insn between ip and ip + func_size.
However, func_size in get_frame_info() is always 0 if KALLSYMS is not
enabled. This causes get_frame_info() to return immediately without
calculating correct frame_size, which in turn causes "Can't analyze
schedule() prologue" warning messages at boot time.
This patch removes func_size check, and let the frame_size check run
up to 128 insns for both MIPS and microMIPS.
Signed-off-by: Jun-Ru Chang <jrjang@realtek.com>
Signed-off-by: Tony Wu <tonywu@realtek.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b6c7a324df37b ("MIPS: Fix get_frame_info() handling of microMIPS function size.")
Cc: <ralf@linux-mips.org>
Cc: <jhogan@kernel.org>
Cc: <macro@mips.com>
Cc: <yamada.masahiro@socionext.com>
Cc: <peterz@infradead.org>
Cc: <mingo@kernel.org>
Cc: <linux-mips@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2a81efb0de0e33f2d2c83154af0bd3ce389b3269 ]
Add compatible to gicv3 node to enable quirk required to restrict writing
to GICR_WAKER register which is restricted on msm8996 SoC in Hypervisor.
With this quirk MSM8996 can at least boot out of mainline, which can help
community to work with boards based on MSM8996.
Without this patch Qualcomm DB820c board reboots on mainline.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ba16adeb346387eb2d1ada69003588be96f098fa ]
devm_ allocated data will be automatically freed. The free
of devm_ allocated data is invalid.
Fixes: 1c459de1e645 ("ARM: pxa: ssp: use devm_ functions")
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
[title's prefix changed]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a8e911d13540487942d53137c156bd7707f66e5d ]
If the kernel is configured with KASAN_EXTRA, the stack size is
increasted significantly because this option sets "-fstack-reuse" to
"none" in GCC [1]. As a result, it triggers stack overrun quite often
with 32k stack size compiled using GCC 8. For example, this reproducer
https://github.com/linux-test-project/ltp/blob/master/testcases/kernel/syscalls/madvise/madvise06.c
triggers a "corrupted stack end detected inside scheduler" very reliably
with CONFIG_SCHED_STACK_END_CHECK enabled.
There are just too many functions that could have a large stack with
KASAN_EXTRA due to large local variables that have been called over and
over again without being able to reuse the stacks. Some noticiable ones
are
size
7648 shrink_page_list
3584 xfs_rmap_convert
3312 migrate_page_move_mapping
3312 dev_ethtool
3200 migrate_misplaced_transhuge_page
3168 copy_process
There are other 49 functions are over 2k in size while compiling kernel
with "-Wframe-larger-than=" even with a related minimal config on this
machine. Hence, it is too much work to change Makefiles for each object
to compile without "-fsanitize-address-use-after-scope" individually.
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715#c23
Although there is a patch in GCC 9 to help the situation, GCC 9 probably
won't be released in a few months and then it probably take another
6-month to 1-year for all major distros to include it as a default.
Hence, the stack usage with KASAN_EXTRA can be revisited again in 2020
when GCC 9 is everywhere. Until then, this patch will help users avoid
stack overrun.
This has already been fixed for arm64 for the same reason via
6e8830674ea ("arm64: kasan: Increase stack size for KASAN_EXTRA").
Link: http://lkml.kernel.org/r/20190109215209.2903-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2aa958c99c7fd3162b089a1a56a34a0cdb778de1 ]
Kexec-ing a kernel with "efi=noruntime" on the first kernel's command
line causes the following null pointer dereference:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
#PF error: [normal kernel read fault]
Call Trace:
efi_runtime_map_copy+0x28/0x30
bzImage64_load+0x688/0x872
arch_kexec_kernel_image_load+0x6d/0x70
kimage_file_alloc_init+0x13e/0x220
__x64_sys_kexec_file_load+0x144/0x290
do_syscall_64+0x55/0x1a0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Just skip the EFI info setup if EFI runtime services are not enabled.
[ bp: Massage commit message. ]
Suggested-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: bhe@redhat.com
Cc: David Howells <dhowells@redhat.com>
Cc: erik.schmauss@intel.com
Cc: fanc.fnst@cn.fujitsu.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: kexec@lists.infradead.org
Cc: lenb@kernel.org
Cc: linux-acpi@vger.kernel.org
Cc: Philipp Rudo <prudo@linux.vnet.ibm.com>
Cc: rafael.j.wysocki@intel.com
Cc: robert.moore@intel.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Cc: Yannik Sembritzki <yannik@sembritzki.me>
Link: https://lkml.kernel.org/r/20190118111310.29589-2-kasong@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f2b3d8566d81deaca31f4e3163def0bea7746e11 ]
On systems with VHE the kernel and KVM's world-switch code run at the
same exception level. Code that is only used on a VHE system does not
need to be annotated as __hyp_text as it can reside anywhere in the
kernel text.
__hyp_text was also used to prevent kprobes from patching breakpoint
instructions into this region, as this code runs at a different
exception level. While this is no longer true with VHE, KVM still
switches VBAR_EL1, meaning a kprobe's breakpoint executed in the
world-switch code will cause a hyp-panic.
Move the __hyp_text check in the kprobes blacklist so it applies on
VHE systems too, to cover the common code and guest enter/exit
assembly.
Fixes: 888b3c8720e0 ("arm64: Treat all entry code as non-kprobe-able")
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
