| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit c24a5c735f87d0549060de31367c095e8810b895 ]
The commit
080edf75d337 ("dmaengine: hsu: set HSU_CH_MTSR to memory width")
has been mistakenly submitted. The further investigations show that
the original code does better job since the memory side transfer size
has never been configured by DMA users.
As per latest revision of documentation: "Channel minimum transfer size
(CHnMTSR)... For IOSF UART, maximum value that can be programmed is 64 and
minimum value that can be programmed is 1."
This reverts commit 080edf75d337d35faa6fc3df99342b10d2848d16.
Fixes: 080edf75d337 ("dmaengine: hsu: set HSU_CH_MTSR to memory width")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Since we have nice macro IRQ_RETVAL() we would use it to convert a flag of
handled interrupt from int to irqreturn_t.
The rationale of doing this is:
a) hence we implicitly mark hsu_dma_do_irq() as an auxiliary function that
can't be used as interrupt handler directly, and
b) to be in align with serial driver which is using serial8250_handle_irq()
that returns plain int by design.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To allow other code to safely read DMA Channel Status Register (where
the register attribute for Channel Error, Descriptor Time Out &
Descriptor Done fields are read-clear), export hsu_dma_get_status().
hsu_dma_irq() is renamed to hsu_dma_do_irq() and requires Status
Register value to be passed in.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
|
|
This tells, for example, IOMMU what the maximum size of a segment
the DMA controller can send.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The timeout capability is only available on the so called DMA write channels,
i.e. associated with UART Rx FIFO. It means we don't need to check the
direction of the channel to handle timeouts.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Current code allows only up to 3 descriptors to be programmed to the hardware
since it is used wrong calculations. Change % to min_t() to allow as many
descriptors as user supplied. At once it could be programmed up to 4
descriptors due to hardware limitations.
The issue was found under stress test, so it might not bother ordinary users.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
There is a typo in documentation regarding to descriptor empty bit (DESCE)
which is set to 1 when descriptor is empty. Thus, status register at the end of
a transfer usually returns all DESCE bits set and thus it will never be zero.
Moreover, there are 2 bits (CDESC) that encode current descriptor, on which
interrupt has been asserted. In case when we have few descriptors programmed we
might have non-zero value.
Remove DESCE and CDESC bits from DMA channel status register (HSU_CH_SR) when
reading it.
Fixes: 2b49e0c56741 ("dmaengine: append hsu DMA driver")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The commit f0579c8ceaf1 ("dmaengine: hsu: speed up residue calculation")
speeded up calculation of the queued descriptor but broke the initial residue
value for active descriptor.
In accordance with documentation the hardware descriptor is updated each time
DMA transfered some bytes. It means we have to calculate a sum of lengths of
non-submitted hardware descriptors and whatever current values in the hardware.
Do this straightforward.
Fixes: f0579c8ceaf1 ("dmaengine: hsu: speed up residue calculation")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
HSU_CH_MTSR register should be programmed to a minimum size to transfer. This
size on a memory side of the transfer. Program it accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
There is no need to calculate an overall length of the descriptor each time we
call for DMA transfer status. Instead we do this at descriptor allocation stage
and keep the stored length for further usage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
There are no platforms where it's not possible to calculate
the number of channels based on IO space length, and since
that is the only purpose for struct hsu_dma_platform_data,
removing it.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All hardware accesses are done under virtual channel lock. That's why specific
channel lock is excessive and can be removed safely. This has been tested on
Intel Medfield and Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The vd->node is removed from the lists when the transfer started so the
vchan_get_all_descriptors() will not find it. This results memory leak.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[andy: fix the typo to prevent a compilation error]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The GFP_ATOMIC is too strict, and DMAEngine documentation make an advice to use
GFP_NOWAIT. This patch does the conversion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are few places where the implemented pieces of code are not needed, i.e.:
- direction can't be wrong in hsu_dma_chan_start()
- desc->active set to 0 by kzalloc
- DMAEngine is NULL-aware when call ->device_alloc_chan_resources()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The HSU DMA is developed to support High Speed UART controllers found in
particular on Intel MID platforms such as Intel Medfield.
The existing implementation is tighten to the drivers/tty/serial/mfd.c driver
and has a lot of disadvantages. Besides that we would like to get rid of the
old HS UART driver in regarding to extending the 8250 which supports generic
DMAEngine API. That's why the current driver has been developed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
