| Age | Commit message (Collapse) | Author |
|---|
|
Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode,
tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us.
tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode:
Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us
Fast-mode: tLOW = 1.39 us, tHIGH = 1.11 us
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
- For a repeated START condition, this controller starts data transfer
immediately after the slave address is written to the TX-FIFO.
- Once the TX-FIFO empty interrupt is asserted, the controller makes
a pause even if additional data are written to the TX-FIFO.
Given those circumstances, the data after a repeated START may not be
transferred if the interrupt is asserted while the TX-FIFO is being
filled up. A more reliable way is to append TX data only in the
interrupt handler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
I was totally screwed up in commit eaba68785c2d ("i2c: uniphier-f:
fix race condition when IRQ is cleared"). Since that commit, if the
number of read bytes is multiple of the FIFO size (8, 16, 24... bytes),
the STOP condition could be issued twice, depending on the timing.
If this happens, the controller will go wrong, resulting in the timeout
error.
It was more than 3 years ago when I wrote this driver, so my memory
about this hardware was vague. Please let me correct the description
in the commit log of eaba68785c2d.
Clearing the IRQ status on exiting the IRQ handler is absolutely
fine. This controller makes a pause while any IRQ status is asserted.
If the IRQ status is cleared first, the hardware may start the next
transaction before the IRQ handler finishes what it supposed to do.
This partially reverts the bad commit with clear comments so that I
will never repeat this mistake.
I also investigated what is happening at the last moment of the read
mode. The UNIPHIER_FI2C_INT_RF interrupt is asserted a bit earlier
(by half a period of the clock cycle) than UNIPHIER_FI2C_INT_RB.
I consulted a hardware engineer, and I got the following information:
UNIPHIER_FI2C_INT_RF
asserted at the falling edge of SCL at the 8th bit.
UNIPHIER_FI2C_INT_RB
asserted at the rising edge of SCL at the 9th (ACK) bit.
In order to avoid calling uniphier_fi2c_stop() twice, check the latter
interrupt. I also commented this because it is obscure hardware internal.
Fixes: eaba68785c2d ("i2c: uniphier-f: fix race condition when IRQ is cleared")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The current IRQ handler clears all the IRQ status bits when it bails
out. This is dangerous because it might clear away the status bits
that have just been set while processing the current handler. If this
happens, the IRQ event for the latest transfer is lost forever.
The IRQ status bits must be cleared *before* the next transfer is
kicked.
Fixes: 6a62974b667f ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Currently, a timeout error could happen at a repeated START condition.
For a (non-repeated) START condition, the controller starts sending
data when the UNIPHIER_FI2C_CR_STA bit is set. However, for a repeated
START condition, the hardware starts running when the slave address is
written to the TX FIFO - the write to the UNIPHIER_FI2C_CR register is
actually unneeded.
Because the hardware is already running before the IRQ is enabled for
a repeated START, the driver may miss the IRQ event. In most cases,
this problem does not show up since modern CPUs are much faster than
the I2C transfer. However, it is still possible that a context switch
happens after the controller starts, but before the IRQ register is
set up.
To fix this,
- Do not write UNIPHIER_FI2C_CR for repeated START conditions.
- Enable IRQ *before* writing the slave address to the TX FIFO.
- Disable IRQ for the current CPU while queuing up the TX FIFO;
If the CPU is interrupted by some task, the interrupt handler
might be invoked due to the empty TX FIFO before completing the
setup.
Fixes: 6a62974b667f ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This is unlikely to happen, but it is possible for a CPU to enter
the interrupt handler just after wait_for_completion_timeout() has
expired. If this happens, the hardware is accessed from multiple
contexts concurrently.
Disable the IRQ after wait_for_completion_timeout(), and do nothing
from the handler when the IRQ is disabled.
Fixes: 6a62974b667f ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This driver currently emits a STOP if the next message is not
I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.
Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.
Fixes: 6a62974b667f ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When resuming, set up registers that have been lost in the sleep state.
Also, add clock handling in the resume / suspend hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Documentation/CodingStyle recommends to use label names which say
what the goto does or why the goto exists.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Currently, the status register FI2C_SR is checked immediately after
a STOP condition is issued in case of the deferred STOP condition.
It takes typically 5-10 usec until the corresponding bits in the
register are set, so the error check for "stop condition was not
completed" is very likely to be false positive.
Add wait code to relax the status register check.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Currently, the adapter is set to the master mode at the first use.
Since then, it is kept in the slave mode, so unexpected glitch
signals on the I2C lines may cause the adapter into insane state.
Setting it to the master mode along with initialization solves the
problem.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Akio Noda <noda.akio@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If clk_prepare_enable() fails, clk_disable_unprepare() is called in
the failure path, where the enable_count is still zero, so it hits
WARN_ON(core->enable_count == 0) in the clk_core_disable().
To fix this, make the clock setting more linear in the probe function
so that it can exploit "goto err" in case of error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Just in case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver. Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add support for on-chip I2C controller used on newer UniPhier SoCs
such as PH1-Pro4, PH1-Pro5, etc. This adapter is equipped with
8-depth TX/RX FIFOs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
