| Age | Commit message (Collapse) | Author |
|---|
|
Add bd71840 driver name to sync the product name on board.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
|
|
Signed-off-by: Haoran.Wang <elven.wang@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
(cherry picked from commit 37f67d291e74a3428310cb5c98f556411042f810)
|
|
When remove sound card build config, there will be error
drivers/built-in.o: In function `mxc_hdmi_register_audio':
vf610_adc.c:(.text+0xd64f8): undefined reference to `_snd_pcm_stream_lock_irqsave'
vf610_adc.c:(.text+0xd6518): undefined reference to `snd_pcm_stream_unlock_irqrestore'
drivers/built-in.o: In function `mxc_hdmi_abort_stream':
vf610_adc.c:(.text+0xd65a4): undefined reference to `_snd_pcm_stream_lock_irqsave'
vf610_adc.c:(.text+0xd65d0): undefined reference to `snd_pcm_stream_unlock_irqrestore'
make: *** [vmlinux] Error 1
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
|
|
Charger interrupt can't be caught anymore after plug in DC 5V in/out dozens of
times, that caused by VBUS_I or CHG_I pending interrupt not cleared in time. The root
cause is VBUS_I and CHG_I will be triggered in very narrow window, and VBUS_I/CHG_I
act as the sub-interrupt of charger and share the same interrupt handler. Thus if CHG_I
interrupt status is coming while VBUS_I handler is running, CHG_I interrupt status will
never be cleared, since interrupt has been disabled in ISR. The unclear CHG_I interrupt
status make pf1550 never trigger next interrupt again. So clear all charger interrupt
status in ISR to workaround instead of ack for every sub-intterrupt.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
|
|
That's pf1550's internal interrupt, useless for charger.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
|
|
voltages
check OTP_SW2_DVS_ENB bit for the different voltage list while SW2
regulator registered.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
|
|
add ".use_ack" ..etc for pf1550 irq, since we have to clear irq status in
pf1550, else no any more interrupt trigged.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
|
|
Correct num_regs of regmap_irq_chip structure, otherwise request irq
failed.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
|
|
Add basic pf1550 mfd driver.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
|
|
null check substream before using it. Reported by coverity.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
(cherry picked from commit fad2b9c1285a34eab0dec9f90edc06ec94e70a61)
|
|
i2c device client shouldn't be freed by i2c device driver, there have
problems in below cases:
- one device match to different drivers, the second matched driver will
cannot access i2c device client if it is freed by the first matched driver.
- one module driver insmod: the first insmod fail free client due to system
low memory, after kswapd system free pages and has enough free pages, the
second insmod will cause match failed.
Signed-off-by: Fugang Duan <B38611@freescale.com>
|
|
Add PMIC 'MAX17135' module drivers to 4.1.y kernel. These are necessary
to supply power for E-ink panel display functions.
Signed-off-by: Robby Cai <r63905@freescale.com>
|
|
Forward imx_3.14.y IPU and display drivers to 4.1 kernel.
This includes IPU core driver, display driver, LDB and HDMI driver.
Signed-off-by: Sandor Yu <R01008@freescale.com>
|
|
The si476x_core_get_revision_info will send i2c command to FM module, if it
return error, there is no FM modules attached, so we need't to register the
sound card. otherwise, the pulseaudio will access this sound card, but return
a lot of i2c error.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
(cherry picked from commit 4c8e9916128f05f9b4115e1ee1af4a1e7d800c4a)
|
|
Currently, si476x-rev1.0 and si476x-rev4.0 board just support A10 compatible
command set. For si476x-rev1.0 board, its firmware revision is unsupported and
will revert to A10 compatible function. For si476x-rev4.0 board, its firmware
revision is two and will use A30 function, but A30 command set function can't
work for the rev4.0 board.
So make the command set configurable in dts. If "revision-a10" is present,
set the revision to SI476X_REVISION_A10 to use A10 compatible commit set.
Otherwise, get the revision from si476x register.
Signed-off-by: Zidan Wang <b50113@freescale.com>
(cherry picked from commit b648714c3b71ee084188ae04b1e6a6f2554fe2cb)
|
|
Add of_compatible for si476x-codec, then si476x-codec driver will have
codec_of_node, So machine driver can use the codec_of_node.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
(cherry picked from commit e2ec44f91a21b127e155e8317d06e8ead7fd2678)
(cherry picked from commit ac6decaf5414e784ae81a524edc2f32060061b59)
|
|
In commit e856a0ebc23dcd2c933e3f902317652cc50f0067, we disabled
wait_event_timeout for CMD_POWER_DOWN, which will cause power down
failed sometimes, then FM will fail to reopen.
In this patch enable the wait_event_timeout for power down.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
(cherry picked from commit 30aa7f1a3580d0a5bc866c624d1da441fd5502c1)
(cherry picked from commit 2b1990fee264d805fcdc0005dcf8b5b63b261d51)
|
|
cherry-pick below patch from imx_3.14.y
ENGR00276567-6 mfd: si476x: Use default configuration when no platform data
This would allow the driver to work normally without specific platform data,
when using devicetree for example.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
(cherry picked from commit 23e369b88b546d7b699ca9ec46e195a05c61b717)
(cherry picked from commit a2449e1d303e341f32556fb7f4ebc7dcbdd9ead1)
|
|
cherry-pick below patch from imx_3.14.y
ENGR00276567-4 mfd: si476x: Fix power up failure
This's some logical error in power-up code, thus fix it.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
(cherry picked from commit 77d97ad1bb77c0e3c60b9781a06b61d4b4667de1)
(cherry picked from commit b656522da2685ef9a4da2229b6786d5cd0c12189)
|
|
[ Upstream commit 10492ee8ed9188d6d420e1f79b2b9bdbc0624e65 ]
It currently only works if the parent bus uses "simple-bus". We
currently try to probe children with non-existing compatible values.
And we're missing .probe.
I noticed this while testing devices configured to probe using ti-sysc
interconnect target module driver. For that we also may want to rebind
the driver, so let's remove __init and __exit.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8c8f74f327a76604a499fad8c54c15e1c0ee8051 ]
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c2b1509c77a99a0dcea0a9051ca743cb88385f50 ]
Use devm_elk_get() to let Linux manage struct clk memory to avoid the following
memory leakage report:
unreferenced object 0xdd75efc0 (size 64):
comm "systemd-udevd", pid 186, jiffies 4294945126 (age 1195.750s)
hex dump (first 32 bytes):
61 64 63 5f 74 73 63 5f 66 63 6b 00 00 00 00 00 adc_tsc_fck.....
00 00 00 00 92 03 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<c0a15260>] kmemleak_alloc+0x40/0x74
[<c0287a10>] __kmalloc_track_caller+0x198/0x388
[<c0255610>] kstrdup+0x40/0x5c
[<c025565c>] kstrdup_const+0x30/0x3c
[<c0636630>] __clk_create_clk+0x60/0xac
[<c0630918>] clk_get_sys+0x74/0x144
[<c0630cdc>] clk_get+0x5c/0x68
[<bf0ac540>] ti_tscadc_probe+0x260/0x468 [ti_am335x_tscadc]
[<c06f3c0c>] platform_drv_probe+0x60/0xac
[<c06f1abc>] driver_probe_device+0x214/0x2dc
[<c06f1c18>] __driver_attach+0x94/0xc0
[<c06efe2c>] bus_for_each_dev+0x90/0xa0
[<c06f1470>] driver_attach+0x28/0x30
[<c06f1030>] bus_add_driver+0x184/0x1ec
[<c06f2b74>] driver_register+0xb0/0xf0
[<c06f3b4c>] __platform_driver_register+0x40/0x54
Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2f606da78230f09cf1a71fde6ee91d0c710fa2b2 ]
Instantiating the sm501 OHCI subdevice results in a kernel warning.
sm501-usb sm501-usb: SM501 OHCI
sm501-usb sm501-usb: new USB bus registered, assigned bus number 1
WARNING: CPU: 0 PID: 1 at ./include/linux/dma-mapping.h:516
ohci_init+0x194/0x2d8
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Tainted: G W
4.18.0-rc7-00178-g0b5b1f9a78b5 #1
PC is at ohci_init+0x194/0x2d8
PR is at ohci_init+0x168/0x2d8
PC : 8c27844c SP : 8f81dd94 SR : 40008001
TEA : 29613060
R0 : 00000000 R1 : 00000000 R2 : 00000000 R3 : 00000202
R4 : 8fa98b88 R5 : 8c277e68 R6 : 00000000 R7 : 00000000
R8 : 8f965814 R9 : 8c388100 R10 : 8fa98800 R11 : 8fa98928
R12 : 8c48302c R13 : 8fa98920 R14 : 8c48302c
MACH: 00000096 MACL: 0000017c GBR : 00000000 PR : 8c278420
Call trace:
[<(ptrval)>] usb_add_hcd+0x1e8/0x6ec
[<(ptrval)>] _dev_info+0x0/0x54
[<(ptrval)>] arch_local_save_flags+0x0/0x8
[<(ptrval)>] arch_local_irq_restore+0x0/0x24
[<(ptrval)>] ohci_hcd_sm501_drv_probe+0x114/0x2d8
...
Initialize coherent_dma_mask when creating SM501 subdevices to fix
the problem.
Fixes: b6d6454fdb66f ("mfd: SM501 core driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6afebb70ee7a4bde106dc1a875e7ac7997248f84 upstream.
Fixes https://bugs.linaro.org/show_bug.cgi?id=3903
LTP Functional tests have caused a bad paging request when triggering
the regmap_read_debugfs() logic of the device PMIC Hi6553 (reading
regmap/f8000000.pmic/registers file during read_all test):
Unable to handle kernel paging request at virtual address ffff0
[ffff00000984e000] pgd=0000000077ffe803, pud=0000000077ffd803,0
Internal error: Oops: 96000007 [#1] SMP
...
Hardware name: HiKey Development Board (DT)
...
Call trace:
regmap_mmio_read8+0x24/0x40
regmap_mmio_read+0x48/0x70
_regmap_bus_reg_read+0x38/0x48
_regmap_read+0x68/0x170
regmap_read+0x50/0x78
regmap_read_debugfs+0x1a0/0x308
regmap_map_read_file+0x48/0x58
full_proxy_read+0x68/0x98
__vfs_read+0x48/0x80
vfs_read+0x94/0x150
SyS_read+0x6c/0xd8
el0_svc_naked+0x30/0x34
Code: aa1e03e0 d503201f f9400280 8b334000 (39400000)
Investigations have showed that, when triggered by debugfs read()
handler, the mmio regmap logic was reading a bigger (16k) register area
than the one mapped by devm_ioremap_resource() during hi655x-pmic probe
time (4k).
This commit changes hi655x's max register, according to HW specs, to be
the same as the one declared in the pmic device in hi6220's dts, fixing
the issue.
Cc: <stable@vger.kernel.org> #v4.9 #v4.14 #v4.16 #v4.17
Signed-off-by: Rafael David Tinoco <rafael.tinoco@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0dbbf25561b29ffab5ba6277429760abdf49ceff ]
If we cannot communicate with the EC chip to detect the protocol version
and its features, it's very likely useless to continue. Else we will
commit all kind of uninformed mistakes (using the wrong protocol, the
wrong buffer size, mixing the EC with other chips).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e93a658576ab115977225c9d0992b97ff19ba8c upstream.
Intel Cannon Lake PCH has much higher 216 MHz input clock to LPSS I2C
than Sunrisepoint which uses 120 MHz. Preliminary information was that
both share the same clock rate but actual silicon implements elevated
rate for better support for 3.4 MHz high-speed I2C.
This incorrect input clock rate results too high I2C bus clock in case
ACPI doesn't provide tuned I2C timing parameters since I2C host
controller driver calculates them from input clock rate.
Fix this by using the correct rate. We still share the same 230 ns SDA
hold time value than Sunrisepoint.
Cc: stable@vger.kernel.org
Fixes: b418bbff36dd ("mfd: intel-lpss: Add Intel Cannonlake PCI IDs")
Reported-by: Jian-Hong Pan <jian-hong@endlessm.com>
Reported-by: Chris Chiu <chiu@endlessm.com>
Reported-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d28b62520830b2d0bffa2d98e81afc9f5e537e8b upstream.
According to documentation REMAP register has to be programmed in
either DMA or PIO mode of the slice.
Move the DMA capability check below to let REMAP register be programmed
in PIO mode.
Cc: stable@vger.kernel.org # 4.3+
Fixes: 4b45efe85263 ("mfd: Add support for Intel Sunrisepoint LPSS devices")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 85e9b13cbb130a3209f21bd7933933399c389ffe upstream.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent node was prematurely freed, while the
child node was leaked.
Note that the CONFIG_OF compile guard can be removed as
of_get_child_by_name() provides a !CONFIG_OF implementation which always
fails.
Fixes: 37e13cecaa14 ("mfd: Add support for Device Tree to twl6040")
Fixes: ca2cad6ae38e ("mfd: Fix twl6040 build failure")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a423772de2f3d7b00899987884f62f63ae00dcb upstream.
A helper purported to look up a child node based on its name was using
the wrong of-helper and ended up prematurely freeing the parent of-node
while leaking any matching node.
To make things worse, any matching node would not even necessarily be a
child node as the whole device tree was searched depth-first starting at
the parent.
Fixes: 019a7e6b7b31 ("mfd: twl4030-audio: Add DT support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15d8374874ded0bec37ef27f8301a6d54032c0e5 upstream.
On the Tegra124 Nyan-Big chromebook the very first SPI message sent to
the EC is failing.
The Tegra SPI driver configures the SPI chip-selects to be active-high
by default (and always has for many years). The EC SPI requires an
active-low chip-select and so the Tegra chip-select is reconfigured to
be active-low when the EC SPI driver calls spi_setup(). The problem is
that if the first SPI message to the EC is sent too soon after
reconfiguring the SPI chip-select, it fails.
The EC SPI driver prevents back-to-back SPI messages being sent too
soon by keeping track of the time the last transfer was sent via the
variable 'last_transfer_ns'. To prevent the very first transfer being
sent too soon, initialise the 'last_transfer_ns' variable after calling
spi_setup() and before sending the first SPI message.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 362741a21a5c4b9ee31e75ce28d63c6d238a745c ]
There is the only path, where mxs_lradc_probe() leaves clk undisabled,
since it does return instead of goto err_clk.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 18f77393796848e68909e65d692c1d1436f06e06 upstream.
When fsl-imx25-tsadc is compiled as a module, loading, unloading and
reloading the module will lead to a crash.
Unable to handle kernel paging request at virtual address bf005430
[<c004df6c>] (irq_find_matching_fwspec)
from [<c028d5ec>] (of_irq_get+0x58/0x74)
[<c028d594>] (of_irq_get)
from [<c01ff970>] (platform_get_irq+0x48/0xc8)
[<c01ff928>] (platform_get_irq)
from [<bf00e33c>] (mx25_tsadc_probe+0x220/0x2f4 [fsl_imx25_tsadc])
irq_find_matching_fwspec() loops over all registered irq domains. The
irq domain is still registered from last time the module was loaded but
the pointer to its operations is invalid after the module was unloaded.
Add a removal function which clears the irq handler and removes the irq
domain. With this cleanup in place, it's possible to unload and reload
the module.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 07d70913dce59f3c8e5d0ca76250861158a9ca6c upstream.
Avoton/Rangeley are based on Silvermount micro-architecture, like
Bay Trail, and uses the INTEL_SPI_BYT method to drive SPI.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This time (again) cpufreq gets the majority of changes which mostly
are driver updates (including a major consolidation of intel_pstate),
some schedutil governor modifications and core cleanups.
There also are some changes in the system suspend area, mostly related
to diagnostics and debug messages plus some renames of things related
to suspend-to-idle. One major change here is that suspend-to-idle is
now going to be preferred over S3 on systems where the ACPI tables
indicate to do so and provide requsite support (the Low Power Idle S0
_DSM in particular). The system sleep documentation and the tools
related to it are updated too.
The rest is a few cpuidle changes (nothing major), devfreq updates,
generic power domains (genpd) framework updates and a few assorted
modifications elsewhere.
Specifics:
- Drop the P-state selection algorithm based on a PID controller from
intel_pstate and make it use the same P-state selection method
(based on the CPU load) for all types of systems in the active mode
(Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to take
cross-CPU utilization updates into account and modify the schedutil
governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the mediatek
cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points (OPP)
DT bindings and update its whitelist of supported systems (Viresh
Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen, Finley
Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to make
it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number of
items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on x86
in a more straightforward way and to use %pOF instead of full_name
(Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor issues
(Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava)"
* tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (87 commits)
cpuidle: Make drivers initialize polling state
cpuidle: Move polling state initialization code to separate file
cpuidle: Eliminate the CPUIDLE_DRIVER_STATE_START symbol
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
PM: docs: Delete the obsolete states.txt document
PM: docs: Describe high-level PM strategies and sleep states
PM / devfreq: Fix memory leak when fail to register device
PM / devfreq: Add dependency on PM_OPP
PM / devfreq: Move private devfreq_update_stats() into devfreq
PM / devfreq: Convert to using %pOF instead of full_name
PM / AVS: rockchip-io: add io selectors and supplies for RV1108
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpuidle: Convert to using %pOF instead of full_name
cpufreq: Convert to using %pOF instead of full_name
PM / Domains: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
...
|
|
Both Bay and Cherry Trail devices may be used together with a Crystal Cove
PMIC. Each platform has its own variant of the PMIC, which both use the
same ACPI HID, but they are not 100% compatible.
This commits makes the intel_soc_pmic_core code check the _HRV of the
ACPI-firmware-node and selects intel_soc_pmic_config_byt_crc resp.
intel_soc_pmic_config_cht_crc based on this.
This fixes the Bay Trail specific ACPI OpRegion code causing problems
on Cherry Trail devices. Specifically this was causing the external
microsd slot on a Dell Venue 8 5855 (Cherry Trail version) to not work
and the eMMC to become unreliable and throw lots of errors.
Fixes: 5165238460 ("mfd: intel_soc_pmic: Core driver")
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Both Bay and Cherry Trail devices may be used together with a Crystal Cove
PMIC. Each platform has its own variant of the PMIC, which both use the
same ACPI HID, but they are not 100% compatible.
Looking at the android x86 kernel sources where most of the Crystal Cove
code comes from, it talks about "Valley View", "Bay Trail" and / or BYT
without ever mentioning Cherry Trail, with the exception of the regulator
driver. The Asus Zenfone-2 kernel code has 2 regulator drivers, one
for Crystal Cove and one for what it calls Crystal Cove Plus. The
Crystal Cove Plus regulator driver is the only one to mention Cherry
Trail and that driver uses different register addresses then the
normal (Bay Trail) Crystal Cove regulator driver, showing that at
least the regulator register addresses are different.
The GPIO code should work on both, and the PWM code is known to work on
both and is necessary for backlight control on some Cherry Trail devices.
Testing has shown that the ACPI OpRegion code otoh is causing problems
on Cherry Trail devices, which is not surprising as it deals with the
regulators and those have different register addresses on CHT.
Specifically the ACPI OpRegion code causes the external microsd slot on
a Dell Venue 8 5855 (Cherry Trail version) to not work and the eMMC to
become unreliable and throw lots of errors.
This commit replaces the single mfd_cell array currently used for Crystal
Cove with 2 separate arrays, one for the Bay Trail variant and one for
the Cherry Trail variant, note that the Cherry Trail version of the array
only contains gpio and pwm cells. The PMIC OpRegion cell is deliberately
not included and drivers for the other cells in the Bay Trail cell array
were never upstreamed.
Fixes: 7cf0a66f32 ("mfd: intel_soc_pmic: Crystal Cove support")
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
gcc-8 notices that the register number calculation is wrong
when the offset is an 'u8' but the number is larger than 256:
drivers/mfd/omap-usb-tll.c: In function 'omap_tll_init':
drivers/mfd/omap-usb-tll.c:90:46: error: overflow in conversion from 'int' to 'u8 {aka unsigned char}' chages value from 'i * 256 + 2070' to '22' [-Werror=overflow]
This addresses it by always using a 32-bit offset number for
the register. This is apparently an old problem that previous
compilers did not find.
Fixes: 16fa3dc75c22 ("mfd: omap-usb-tll: HOST TLL platform driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
spi_device_id are not supposed to change at runtime. All functions
working with spi_device_id provided by <linux/i2c.h> work with
const spi_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Commit 274e43edcda6f ("mfd: intel-lpss: Do not put device in reset
state on suspend") changed the behavior on suspend by not putting LPSS
controllers into reset. This was done because S3/S0ix fail if UART
device is put into reset and no_console_suspend flag is enabled.
Because of the above change, I2C controller gets into a bad state if
it observes that the I2C lines are pulled low when power to I2C device
is cut off during suspend (generally, I2C lines are pulled to power
rail of the I2C device in order to ensure that there is no leakage
because of the pulls when device is turned off). This results in the
controller timing out for all future I2C operations after resume. It
is primarily because of the following sequence of operations:
During suspend:
1. I2C controller is disabled, but it is not put into reset.
2. Power to I2C device is cut off.
3. #2 results in the I2C lines being pulled low.
==> At this point the I2C controller gets into a bad state
On resume:
1. Power to I2C device is enabled.
2. #2 results in the I2C lines being pulled high.
3. I2C controller is enabled.
However, even after enabling the I2C controller, all future I2C xfers
fail since the controller is in a bad state and does not attempt to
make any transactions and hence times out.
In order to ensure that the controller does not get into a bad state,
this change puts it into reset if the controller type is not
UART. With this change, the order of operations is:
During suspend:
1. I2C controller is disabled and put into reset.
2. Power to I2C device is cut off.
3. #2 results in the I2C lines being pulled low.
On resume:
1. Power to I2C device is enabled.
2. #2 results in the I2C lines being pulled high.
3. I2C controller is enabled and taken out of reset.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds a missing PCI ID of the Intel Sunrise Point chipset to the Intel LPSS driver.
It fixes a bug causing the touchpad of the Lenovo Yoga 720-15 not to be recognized.
See also bug 1700657 on bugs.launchpad.net.
Many thanks to CoolStar, who found this solution!
Reported-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: Mike Schwartz <mykesx@gmail.com>
Tested-by: Björn Dahlgren <bjodah@gmail.com>
Signed-off-by: Florian R. Hölzlwimmer <git.ich@frhoelzlwimmer.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
clk_prepare_enable() can fail here and we must check its return value.
we must disable clock, if t7l66xb_probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The PMIC provides ACPI OpRegions which must be available for other
drivers' PS0 / PS3 methods early-on as such it must be builtin as the
Kconfig help text already states.
Somehow its Kconfig option ended up being a tristate though, this fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This fixes missing mfd_remove_devices() call when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The TPS68470 device is an advanced power management
unit that powers a Compact Camera Module (CCM),
generates clocks for image sensors, drives a dual
LED for Flash and incorporates two LED drivers for
general purpose indicators.
This patch adds support for TPS68470 mfd device.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
At least on Lenovo Thinkpad Yoga, the BIOS seems to monitor the SPI-NOR
write protection bit and if it is flipped to read/write it assumes the
BIOS configuration was changed on next reboot. It then, for unknown
reasons, resets the BIOS settings back to default.
We can prevent this by just leaving the write protection bit intact and
let the SPI-NOR driver know whether the device is writable or not. In
case of this particular Lenovo the SPI-NOR flash will be exposed as
read-only.
Fixes: ff00d7a32a1b ("mfd: lpc_ich: Add support for SPI serial flash host controller")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195951
Reported-by: Abdó Roig-Marange <abdo.roig@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
For HSMC controller, the register layout depends on the device i.e. the
offset of setup, pulse, cycle, mode and timings registers is not the
same. An helper is added to provide the correct register layout.
Fixes: fe9d7cb22ef3 ("mfd: syscon: atmel-smc: Add new helpers to ease
SMC regs manipulation")
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
