| Age | Commit message (Collapse) | Author |
|---|
|
When the line discipline install fails for reasons such as missing user-space
UIM or broken communication between UIM and ST driver, then the ST
attempts/retries to request for ldisc installation again.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
download firmware behaves differently at different times, when logs are
enabled and the system is loaded, the wait_for_completion is able to wait for
every send, However during other times the wait does not happen.
So, for reliability reinitializing the completion before every send, makes
sure the wait happens for every send.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Texas Instrument's shared transport driver interpret incoming data from the
UART based on the various protocol drivers registered to the driver such as
btwilink driver or FM or GPS driver which provide logical channel IDs.
In case of bad-behavior from chip such as HCI Event response for a GPS command
or a HCI Event (h/w error event) for a FM response & In case of bad-behavior
from UART driver such as dropping data bytes a fail-safe is required to avoid
kernel panic.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Vijay Badawadagi <bvijay@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
After the version information has been read, the completion which assists in
wait_for_completion during the firmware send/wait sequence is being re-used
and hence this needs to be re-initialised for fool proof firmware download
retries.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Certain platform specific or Host-WiLink Interface specific actions would be
required to be taken when the chip is being enabled and after the chip is
disabled such as configuration of the mux modes for the GPIO of host connected
to the nshutdown of the chip or relinquishing UART after the chip is disabled.
Similar actions can also be taken when the chip is in deep sleep or when the
chip is awake. Performance enhancements such as configuring the host to run
faster when chip is awake and slower when chip is asleep can also be made
here.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Previously the private data of each protocol registered to use ST was
used to determine whether the protocol was registered to use shared
transport or otherwise.
However, now a flag is_registered is maintained to identify whether a
protocol intends to use ST.
Upon closing of the UART the error message relevant to this lack of
un-registration was misleading and this patch fixes that.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
allmodconfig compile fails on s390 because of the new PTI driver:
drivers/misc/pti.c:407:3: error: implicit declaration of function 'pci_iounmap'
drivers/misc/pti.c:410:3: error: implicit declaration of function 'pci_release_region'
Add a 'depends on PCI' statement so it doesn't get compiled.
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With the arrival of concurrency-managed workqueues there is no need for
our driver to use dedicated workqueue; system-wide one should suffice just
fine.
[akpm@linux-foundation.org: fix comment layout & grammar]
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (26 commits)
amba pl011: workaround for uart registers lockup
n_gsm: fix the wrong FCS handling
pch_uart: add missing comment about OKI ML7223
pch_uart: Add MSI support
tty: fix "IRQ45: nobody cared"
PTI feature to allow user to name and mark masterchannel request.
0 for o PTI Makefile bug.
tty: serial: samsung.c remove legacy PM code.
SERIAL: SC26xx: Fix link error.
serial: mrst_max3110: initialize waitqueue earlier
mrst_max3110: Change max missing message priority.
tty: s5pv210: Add delay loop on fifo reset function for UART
tty/serial: Fix XSCALE serial ports, e.g. ce4100
serial: bfin_5xx: fix off-by-one with resource size
drivers/tty: use printk_ratelimited() instead of printk_ratelimit()
tty: n_gsm: Added refcount usage to gsm_mux and gsm_dlci structs
tty: n_gsm: Add raw-ip support
tty: n_gsm: expose gsmtty device nodes at ldisc open time
pch_phub: Fix register miss-setting issue
serial: 8250, increase PASS_LIMIT
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
updated Documentation/ja_JP/SubmittingPatches
debugfs: add documentation for debugfs_create_x64
uio: uio_pdrv_genirq: Add OF support
firmware: gsmi: remove sysfs entries when unload the module
Documentation/zh_CN: Fix messy code file email-clients.txt
driver core: add more help description for "path to uevent helper"
driver-core: modify FIRMWARE_IN_KERNEL help message
driver-core: Kconfig grammar corrections in firmware configuration
DOCUMENTATION: Replace create_device() with device_create().
DOCUMENTATION: Update overview.txt in Doc/driver-model.
pti: pti_tty_install documentation mispelling.
|
|
* Merge akpm patch series: (122 commits)
drivers/connector/cn_proc.c: remove unused local
Documentation/SubmitChecklist: add RCU debug config options
reiserfs: use hweight_long()
reiserfs: use proper little-endian bitops
pnpacpi: register disabled resources
drivers/rtc/rtc-tegra.c: properly initialize spinlock
drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
drivers/rtc: add support for Qualcomm PMIC8xxx RTC
drivers/rtc/rtc-s3c.c: support clock gating
drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
init: skip calibration delay if previously done
misc/eeprom: add eeprom access driver for digsy_mtc board
misc/eeprom: add driver for microwire 93xx46 EEPROMs
checkpatch.pl: update $logFunctions
checkpatch: make utf-8 test --strict
checkpatch.pl: add ability to ignore various messages
checkpatch: add a "prefer __aligned" check
checkpatch: validate signature styles and To: and Cc: lines
checkpatch: add __rcu as a sparse modifier
checkpatch: suggest using min_t or max_t
...
Did this as a merge because of (trivial) conflicts in
- Documentation/feature-removal-schedule.txt
- arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
|
|
Both displays on digsy_mtc board obtain their configuration from microwire
EEPROMs which are connected to the SoC over GPIO lines. We need an easy
way to access the EEPROMs to write the needed display configuration or to
read out the currently programmed configuration. The generic
eeprom_93xx46 SPI driver added by previous patch allows EEPROM access over
sysfs. Using the simple driver added by this patch we provide used GPIO
interface and access control description on the board for generic
eeprom_93xx46 driver and spi_gpio driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add EEPROM driver for 93xx46 chips. It can also be used with spi_gpio
driver to access 93xx46 EEPROMs connected over GPIO lines. This driver
supports read/write/erase access to the EEPROM chips over sysfs files.
[rdunlap@xenotime.net: fix printk format]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The FSA9480 is a USB port accessory detector and switch. This patch adds
support the FSA9480 USB Switch.
[akpm@linux-foundation.org: make a couple of things static]
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As stated in drivers/mfd/cs5535-mfd.c, the mfd driver exposes the BARs
which then make the GPIO, MFGPT, ACPI, etc. all visible to the system.
So the dependencies of the MFGPT stuff have changed, and most people
expect Kconfig to bring in the necessary dependencies. Without them, the
module fails to load and most people don't understand why because the
details of the rewrite aren't captured anywhere most people who know to
look.
This dependency needs to be reflected in Kconfig.
Signed-off-by: Philip A. Prindeville <philipp@redfish-solutions.com>
Acked-by: Alexandros C. Couloumbis <alex@ozo.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If dmi_get_system_info() returns NULL, pch_phub_probe() will dereferencea
a zero pointer.
This oops was observed on an Atom based board which has no BIOS, but a
bootloder which doesn't privde DMI data.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sync with Linus' tree to be able to apply pending patches that
are based on newer code already present upstream.
|
|
This feature addition provides a new parameter in
pti_request_masterchannel() to allow the user
to provide their own name to mark the request when
the trace is viewed in a PTI SW trace viewer
(like MPTA). If a name is not provided and
NULL is provided, the 'current' process name is used.
API function header documentation documents this.
Signed-off-by: Jeremy Rocher <rocher.jeremy@gmail.com>
Signed-off-by: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes an issue where 'obj' was actually
spelled '0bj' and would skip compiling the pti driver.
Signed-off-by: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Register "interrupt delay value" is for GbE which is connected to Bus-m of PCIe.
However currently, the value is set for Bus-n.
As a result, the value is not set correctly.
This patch moves setting the value processing of Bus-n to Bus-m.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6
* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Connector: Correctly set the error code in case of success when dispatching receive callbacks
Connector: Set the CN_NETLINK_USERS correctly
pti: PTI semantics fix in pti_tty_cleanup.
pti: ENXIO error case memory leak PTI fix.
pti: double-free security PTI fix
drivers:misc: ti-st: fix skipping of change remote baud
drivers/base/platform.c: don't mark platform_device_register_resndata() as __init_or_module
st_kim: Handle case of no device found for ID 0
firmware: fix GOOGLE_SMI kconfig dependency warning
|
|
Fix this section mismatch:
WARNING: drivers/misc/ioc4.o(.data+0x144): Section mismatch in reference from the variable ioc4_load_modules_work to the function .devinit.text:ioc4_load_modules()
The variable ioc4_load_modules_work references
the function __devinit ioc4_load_modules()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
This one is potentially fatal; by the time ioc4_load_modules is invoked
it may already have been freed. For that reason ioc4_load_modules_work
can't be turned to __devinitdata but also because it's referenced in
ioc4_exit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Brent Casavant <bcasavan@sgi.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
checking count
We observed the crash point count going negative in cases where the
crash point is hit multiple times before the check of "count == 0" is
done. Because of this we never call lkdtm_do_action(). This patch just
adds a spinlock to protect count.
Reported-by: Tapan Dhimant <tdhimant@akamai.com>
Signed-off-by: Josh Hunt <johunt@akamai.com>
Acked-by: Ankita Garg <ankita@in.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: queue: bring discard_granularity/alignment into line with SCSI
mmc: queue: append partition subname to queue thread name
mmc: core: make erase timeout calculation allow for gated clock
mmc: block: switch card to User Data Area when removing the block driver
mmc: sdio: reset card during power_restore
mmc: cb710: fix #ifdef HAVE_EFFICIENT_UNALIGNED_ACCESS
mmc: sdhi: DMA slave ID 0 is invalid
mmc: tmio: fix regression in TMIO_MMC_WRPROTECT_DISABLE handling
mmc: omap_hsmmc: use original sg_len for dma_unmap_sg
mmc: omap_hsmmc: fix ocr mask usage
mmc: sdio: fix runtime PM path during driver removal
mmc: Add PCI fixup quirks for Ricoh 1180:e823 reader
mmc: sdhi: fix module unloading
mmc: of_mmc_spi: add NO_IRQ define to of_mmc_spi.c
mmc: vub300: fix null dereferences in error handling
|
|
HAVE_EFFICIENT_UNALIGNED_ACCESS is a config option, therefore it needs
the CONFIG_ before it when used by the preprocessor.
Signed-off-by: James Hogan <james@albanarts.com>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
pxa168_eth: fix race in transmit path.
ipv4, ping: Remove duplicate icmp.h include
netxen: fix race in skb->len access
sgi-xp: fix a use after free
hp100: fix an skb->len race
netpoll: copy dev name of slaves to struct netpoll
ipv4: fix multicast losses
r8169: fix static initializers.
inet_diag: fix inet_diag_bc_audit()
gigaset: call module_put before restart of if_open()
farsync: add module_put to error path in fst_open()
net: rfs: enable RFS before first data packet is received
fs_enet: fix freescale FCC ethernet dp buffer alignment
netdev: bfin_mac: fix memory leak when freeing dma descriptors
vlan: don't call ndo_vlan_rx_register on hardware that doesn't have vlan support
caif: Bugfix - XOFF removed channel from caif-mux
tun: teach the tun/tap driver to support netpoll
dp83640: drop PHY status frames in the driver.
dp83640: fix phy status frame event parsing
phylib: Allow BCM63XX PHY to be selected only on BCM63XX.
...
|
|
Its illegal to dereference skb after dev_kfree_skb(skb)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Robin Holt <holt@sgi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CONFIG_PM_RUNTIME
Fixes this warning:
drivers/misc/apds990x.c: At top level:
drivers/misc/apds990x.c:613: warning: `apds990x_chip_on' defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the wrong `if' condition for the check if the requested timer is
available.
The bitmap avail is used to store if a timer is used already. test_bit()
is used to check if the requested timer is available. If a bit in the
avail bitmap is set it means that the timer is available.
The runtime effect would be that allocating a specific timer always fails
(versus telling cs5535_mfgpt_alloc_timer to allocate the first available
timer, which works).
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
spear_pcie_gadget_probe error path
In the case of goto err_kzalloc, we should kfree target.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch tidies up the documentation for pti_tty_install()
function.
Signed-off-by: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes a semantics issue in the pti_tty_cleanup()
routine.
Signed-off-by: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes a memory leak that can occur in the error case
ENXIO is returned in the pti_tty_install() routine.
Signed-off-by: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes a double-free error that will not always be
seen unless /dev/pti char interface is stressed.
Signed-off-by: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Before the incrementing of ptr in skip_change_remote_baud,
it points to cur_action, but the increment is done by
the size of nxt_action instead. This could cause ptr
to not point to a bts_action structure, which is
harmful for the increment of ptr done in download_firmware.
Therefore, the skipping is first done for cur_action.
Signed-off-by: Shahar Lev <shahar@wizery.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Running ktest.pl, I hit this bug:
[ 19.780654] BUG: unable to handle kernel NULL pointer dereference at 0000000c
[ 19.780660] IP: [<c112efcd>] dev_get_drvdata+0xc/0x46
[ 19.780669] *pdpt = 0000000031daf001 *pde = 0000000000000000
[ 19.780673] Oops: 0000 [#1] SMP
[ 19.780680] Dumping ftrace buffer:^M
[ 19.780685] (ftrace buffer empty)
[ 19.780687] Modules linked in: ide_pci_generic firewire_ohci firewire_core evbug crc_itu_t e1000 ide_core i2c_i801 iTCO_wdt
[ 19.780697]
[ 19.780700] Pid: 346, comm: v4l_id Not tainted 2.6.39-test-02740-gcaebc16-dirty #4 /DG965MQ
[ 19.780706] EIP: 0060:[<c112efcd>] EFLAGS: 00010202 CPU: 0
[ 19.780709] EIP is at dev_get_drvdata+0xc/0x46
[ 19.780712] EAX: 00000008 EBX: f1e37da4 ECX: 00000000 EDX: 00000000
[ 19.780715] ESI: f1c3f200 EDI: c33ec95c EBP: f1e37d80 ESP: f1e37d80
[ 19.780718] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 19.780721] Process v4l_id (pid: 346, ti=f1e36000 task=f2bc2a60 task.ti=f1e36000)
[ 19.780723] Stack:
[ 19.780725] f1e37d8c c117d395 c33ec93c f1e37db4 c117a0f9 00000002 00000000 c1725e54
[ 19.780732] 00000001 00000007 f2918c90 f1c3f200 c33ec95c f1e37dd4 c1789d3d 22222222
[ 19.780740] 22222222 22222222 f2918c90 f1c3f200 f29194f4 f1e37de8 c178d5c4 c1725e54
[ 19.780747] Call Trace:
[ 19.780752] [<c117d395>] st_kim_ref+0x28/0x41
[ 19.780756] [<c117a0f9>] st_register+0x29/0x562
[ 19.780761] [<c1725e54>] ? v4l2_open+0x111/0x1e3
[ 19.780766] [<c1789d3d>] fmc_prepare+0x97/0x424
[ 19.780770] [<c178d5c4>] fm_v4l2_fops_open+0x70/0x106
[ 19.780773] [<c1725e54>] ? v4l2_open+0x111/0x1e3
[ 19.780777] [<c1725e9b>] v4l2_open+0x158/0x1e3
[ 19.780782] [<c065173b>] chrdev_open+0x22c/0x276
[ 19.780787] [<c0647c4e>] __dentry_open+0x35c/0x581
[ 19.780792] [<c06498f9>] nameidata_to_filp+0x7c/0x96
[ 19.780795] [<c065150f>] ? cdev_put+0x57/0x57
[ 19.780800] [<c0660cad>] do_last+0x743/0x9d4
[ 19.780804] [<c065d5fc>] ? path_init+0x1ee/0x596
[ 19.780808] [<c0661481>] path_openat+0x10c/0x597
[ 19.780813] [<c05204a1>] ? trace_hardirqs_off+0x27/0x37
[ 19.780817] [<c0509651>] ? local_clock+0x78/0xc7
[ 19.780821] [<c0661945>] do_filp_open+0x39/0xc2
[ 19.780827] [<c1cabc76>] ? _raw_spin_unlock+0x4c/0x5d^M
[ 19.780831] [<c0674ccd>] ? alloc_fd+0x19e/0x1b7
[ 19.780836] [<c06499ca>] do_sys_open+0xb7/0x1bd
[ 19.780840] [<c0608eea>] ? sys_munmap+0x78/0x8d
[ 19.780844] [<c0649b06>] sys_open+0x36/0x58
[ 19.780849] [<c1cb809f>] sysenter_do_call+0x12/0x38
[ 19.780852] Code: d8 2f 20 c3 01 83 15 dc 2f 20 c3 00 f0 ff 00 83 05 e0 2f 20 c3 01 83 15 e4 2f 20 c3 00 5d c3 55 89 e5 3e 8d 74 26 00 85 c0 74 28 <8b> 40 04 83 05 e8 2f 20 c3 01 83 15 ec 2f 20 c3 00 85 c0 74 13 ^M
[ 19.780889] EIP: [<c112efcd>] dev_get_drvdata+0xc/0x46 SS:ESP 0068:f1e37d80
[ 19.780894] CR2: 000000000000000c
[ 19.780898] ---[ end trace e7d1d0f6a2d1d390 ]---
The id of 0 passed to st_kim_ref() found no device, keeping pdev null,
and causing pdev->dev cause a NULL pointer dereference. After having
st_kim_ref() check for NULL, the st_unregister() function needed to be
updated to handle the case that st_gdata was not set by the
st_kim_ref().
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This reverts commit b1c43f82c5aa265442f82dba31ce985ebb7aa71c.
It was broken in so many ways, and results in random odd pty issues.
It re-introduced the buggy schedule_work() in flush_to_ldisc() that can
cause endless work-loops (see commit a5660b41af6a: "tty: fix endless
work loop when the buffer fills up").
It also used an "unsigned int" return value fo the ->receive_buf()
function, but then made multiple functions return a negative error code,
and didn't actually check for the error in the caller.
And it didn't actually work at all. BenH bisected down odd tty behavior
to it:
"It looks like the patch is causing some major malfunctions of the X
server for me, possibly related to PTYs. For example, cat'ing a
large file in a gnome terminal hangs the kernel for -minutes- in a
loop of what looks like flush_to_ldisc/workqueue code, (some ftrace
data in the quoted bits further down).
...
Some more data: It -looks- like what happens is that the
flush_to_ldisc work queue entry constantly re-queues itself (because
the PTY is full ?) and the workqueue thread will basically loop
forver calling it without ever scheduling, thus starving the consumer
process that could have emptied the PTY."
which is pretty much exactly the problem we fixed in a5660b41af6a.
Milton Miller pointed out the 'unsigned int' issue.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Milton Miller <miltonm@bga.com>
Cc: Stefan Bigler <stefan.bigler@keymile.com>
Cc: Toby Gray <toby.gray@realvnc.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The new instruction_pointer_set helper is defined for people who have
converted to asm-generic/ptrace.h, so don't use it generally unless
the arch needs it (in which case it has been converted). This should
fix building of kgdb tests for arches not yet converted.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The Blackfin arch, like the x86 arch, needs to adjust the PC manually
after a breakpoint is hit as normally this is handled by the remote gdb.
However, rather than starting another arch ifdef mess, create a common
GDB_ADJUSTS_BREAK_OFFSET define for any arch to opt-in via their kgdb.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Dongdong Deng <dongdong.deng@windriver.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (48 commits)
serial: 8250_pci: add support for Cronyx Omega PCI multiserial board.
tty/serial: Fix break handling for PORT_TEGRA
tty/serial: Add explicit PORT_TEGRA type
n_tracerouter and n_tracesink ldisc additions.
Intel PTI implementaiton of MIPI 1149.7.
Kernel documentation for the PTI feature.
export kernel call get_task_comm().
tty: Remove to support serial for S5P6442
pch_phub: Support new device ML7223
8250_pci: Add support for the Digi/IBM PCIe 2-port Adapter
ASoC: Update cx20442 for TTY API change
pch_uart: Support new device ML7223 IOH
parport: Use request_muxed_region for IT87 probe and lock
tty/serial: add support for Xilinx PS UART
n_gsm: Use print_hex_dump_bytes
drivers/tty/moxa.c: Put correct tty value
TTY: tty_io, annotate locking functions
TTY: serial_core, remove superfluous set_task_state
TTY: serial_core, remove invalid test
Char: moxa, fix locking in moxa_write
...
Fix up trivial conflicts in drivers/bluetooth/hci_ldisc.c and
drivers/tty/serial/Makefile.
I did the hci_ldisc thing as an evil merge, cleaning things up.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (152 commits)
powerpc: Fix hard CPU IDs detection
powerpc/pmac: Update via-pmu to new syscore_ops
powerpc/kvm: Fix the build for 32-bit Book 3S (classic) processors
powerpc/kvm: Fix kvmppc_core_pending_dec
powerpc: Remove last piece of GEMINI
powerpc: Fix for Pegasos keyboard and mouse
powerpc: Make early memory scan more resilient to out of order nodes
powerpc/pseries/iommu: Cleanup ddw naming
powerpc/pseries/iommu: Find windows after kexec during boot
powerpc/pseries/iommu: Remove ddw property when destroying window
powerpc/pseries/iommu: Add additional checks when changing iommu mask
powerpc/pseries/iommu: Use correct return type in dupe_ddw_if_already_created
powerpc: Remove unused/obsolete CONFIG_XICS
misc: Add CARMA DATA-FPGA Programmer support
misc: Add CARMA DATA-FPGA Access Driver
powerpc: Make IRQ_NOREQUEST last to clear, first to set
powerpc: Integrated Flash controller device tree bindings
powerpc/85xx: Create dts of each core in CAMP mode for P1020RDB
powerpc/85xx: Fix PCIe IDSEL for Px020RDB
powerpc/85xx: P2020 DTS: re-organize dts files
...
|
|
Commit e66eed651fd1 ("list: remove prefetching from regular list
iterators") removed the include of prefetch.h from list.h, which
uncovered several cases that had apparently relied on that rather
obscure header file dependency.
So this fixes things up a bit, using
grep -L linux/prefetch.h $(git grep -l '[^a-z_]prefetchw*(' -- '*.[ch]')
grep -L 'prefetchw*(' $(git grep -l 'linux/prefetch.h' -- '*.[ch]')
to guide us in finding files that either need <linux/prefetch.h>
inclusion, or have it despite not needing it.
There are more of them around (mostly network drivers), but this gets
many core ones.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Manual merge of arch/powerpc/kernel/smp.c and add missing scheduler_ipi()
call to arch/powerpc/platforms/cell/interrupt.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This adds support for programming the data processing FPGAs on the OVRO
CARMA board. These FPGAs have a special programming sequence that
requires that we program the Freescale DMA engine, which is only
available inside the kernel.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This driver allows userspace to access the data processing FPGAs on the
OVRO CARMA board. It has two modes of operation:
1) random access
This allows users to poke any DATA-FPGA registers by using mmap to map
the address region directly into their memory map.
2) correlation dumping
When correlating, the DATA-FPGA's have special requirements for getting
the data out of their memory before the next correlation. This nominally
happens at 64Hz (every 15.625ms). If the data is not dumped before the
next correlation, data is lost.
The data dumping driver handles buffering up to 1 second worth of
correlation data from the FPGAs. This lowers the realtime scheduling
requirements for the userspace process reading the device.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The PTI (Parallel Trace Interface) driver directs
trace data routed from various parts in the system out
through an Intel Penwell PTI port and out of the mobile
device for analysis with a debugging tool (Lauterbach or Fido).
Though n_tracesink and n_tracerouter line discipline drivers
are used to extract modem tracing data to the PTI driver
and other parts of an Intel mobile solution, the PTI driver
can be used independent of n_tracesink and n_tracerouter.
You should select this driver if the target kernel is meant for
an Intel Atom (non-netbook) mobile device containing a MIPI
P1149.7 standard implementation.
Signed-off-by: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
