| Age | Commit message (Collapse) | Author |
|---|
|
If the driver receives a TX CQE with status as 0x1 or 0x9 or 0xb,
the completion indexes should not be used. The driver must stop
consuming CQEs from this TXQ/CQ. The TXQ from this point on-wards
to be in a bad state. Driver should destroy and recreate the TXQ.
0x1: LANCER_TX_COMP_LSO_ERR
0x9 LANCER_TX_COMP_SGE_ERR
0xb: LANCER_TX_COMP_PARITY_ERR
Reset the adapter if driver sees this error in TX completion. Also
adding sge error counter in ethtool stats.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On certain platforms BE3 chips may indicate spurious UEs (unrecoverable
error). Because of the UE detection logic was disabled in the driver
for BE3 chips. Because of this, even in cases of a real UE,
a failover will not occur. This patch re-enables UE detection on BE3
and if a UE is detected, reads the POST register. If the POST register,
reports either a FAT_LOG_STATE or a ARMFW_UE, then it means that a valid
UE occurred in the chip.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the year and company name in the copyright string
in be_hw.h.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch supports recovery from UEs caused due to Transient Parity
Errors (TPE), in BE2, BE3 and Skyhawk adapters. This change avoids
system reboot when such errors occur. The driver recovers from these
errors such that the adapter resumes full operational status as prior
to the UE.
Following is the list of changes in the driver to support this:
o The driver registers its UE recoverable capability with ARM FW at init
time. This also allows the driver to know if the feature is supported in
the FW.
o As the UE recovery requires precise time bound processing, the driver
creates its own error recovery work queue with a single worker thread (per
module, shared across functions).
o Each function runs an error detection task at an interval of 1 second as
required by the FW. The error detection logic already exists for BEx/SH,
but it now runs in the context of a separate worker thread.
o When an error is detected by the task, if it is recoverable, the PF0
driver instance initiates a soft reset, while other PF driver instances
wait for the reset to complete and the chip to become ready. Once
the chip is ready, all driver instances including PF0, resume to
reinitialize the respective functions.
o The PF0 driver checks for some recovery criteria, to determine if the
recovery can be initiated. If the criteria is not met, the PF0 driver does
not initiate a soft reset, it retains the existing behavior to stop
further processing and requires a reboot to get the chip to operational
state again.
o To allow each function to share the workq, while also making progress in
its recovery process, a per-function recovery state machine is used.
The per-function tasks avoid blocking operations like msleep() while in
this state machine (until reinit state) and instead reschedule for the
required delay.
o With these changes, the existing error recovery code for Lancer also
runs in the context of the new worker thread.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vasundhara Volam <vasundhara.volam@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently adaptive interrupt moderation is set by calculating
and configuring an EQ-delay every second. This is done via
a FW-cmd. But, on Skyhawk-R a "re-arm to interrupt" delay
can be set while ringing the EQ-DB. This patch uses this
facility to calculate and set the interrupt delay every 1ms.
This helps moderating interrupts better when the traffic
is bursty.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 32-bit fields of a tx-wrb are little endian. The driver is currently
using be_dws_le_to_cpu() routine to swap (cpu to le) all the fields of
a tx-wrb. So, the rsvd field is also unnecessarily swapped.
This patch fixes this by individually swapping the required fields.
Also, the type of the fields in eth_tx_wrb{} is now changed to __le32
from u32 to avoid sparse warnings.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BIT(x) is the preffered usage.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some FW cmd related definitions were included in be_hw.h
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch uses skb->xmit_more flag to batch TX requests.
TX is flushed either when xmit_more is false or there is
no more space in the TXQ.
Skyhawk-R and BEx chips require an even number of wrbs to be posted.
So, when a batch of TX requests is accumulated, the last header wrb
may need to be fixed with an extra dummy wrb.
This patch refactors be_xmit() routine as a sequence of be_xmit_enqueue()
and be_xmit_flush() calls. The Tx completion code is also
updated to be able to unmap/free a batch of skbs rather than a single
skb.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW reports TX completion errors in TX completion. This patch adds these
counters to ethtool statistics.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Certain new flash regions have been added to Skyhawk-R FW image. The newer
FW images specify op_types for each region. A region is flashed only
when it's CRC doesn't match that of the region on the HW flash. While
upgrading to a new FW image the driver is expected to tolerate certain
errors.
This patch re-factors code under be_flash() to support the above scheme.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch mainly implements the add/del_vxlan_port() methods by invoking
the needed FW cmds for supporting VxLAN offloads for Skyhawk-R.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently multi-channel configuration is read via the QUERY_FW_CONFIG cmd.
This method has been deprecated by the Skyhawk-R FW. Instead,
GET_PROFILE_CONFIG::port-desc must be used to query this configuration.
This patch also:
a) introduces a few macros to identify certain categories of multi-channel
configs
2) re-factors the be_cmd_set_profile_config() code to be able to read any kind
of desc (and not just the nic-desc.)
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Firmware update would be detected by looking at the sliport_error1/
sliport_error2 register values(0x02/0x00). If its not a FW reset the current
messaging would take place. If the error is due to FW reset, log a message to
user that "Firmware update in progress" and also do not log sliport_status and
sliport_error register values.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added code to initiate FW dump via ethtool. Driver checks if the previous dump
has been cleared before initiating the dump. It doesn't initiate the dump
if it is not cleared.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW does not compute L4 checksum for IP Fragmented packets.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid flashing BE3 UFI on BE3-R chip by verifying asic_revision
number of the chip.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Skyhawk-R and BE3-R (SuperNIC profile) require V2 version
of TXQ_CREATE cmd to be used.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/intel/e1000e/netdev.c
Minor conflict in e1000e, a line that got fixed in 'net'
has been removed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SLIPORT_SEMAPHORE register shadowed in the
config-space may not reflect the correct POST stage after
an EEH reset in BE2/3; it may return FW_READY state even though
FW is not ready. This causes the driver to prematurely
poll the FW mailbox and fail.
For BE2/3 use the CSR-BAR/0xac instead.
Reported-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SEMAPHORE register was being accessed from the csr BAR space. This BAR
may not be available in some Skyhawk-R configurations. Instead, access this
register via the PCI config space (it's available there too).
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SKYHAWK_FAMILY will not identify all revisions of the chip.
Use device-id check (skyhawk_chip() macro) instead.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After FW error, driver should wait for NO_RESOURCE error to disappear before
proceeding with recovery.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After FW download, activate new FW by invoking FW reset.
Recreate rings once new FW is operational.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CUST_SCRATCHPAD_CSR register is used for marking if FW cleanup is
needed. This is used in a crash kernel scenario. Do no use this register as
it is not available for some functions. Instead, always issue an FLR when
a function is probed *except* when VFs are preset (enabled in the previous
PF load).
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
- Add generic and mlx4 support for "raw" QPs: allow suitably privileged
applications to send and receive arbitrary packets directly to/from
the hardware
- Add "doorbell drop" handling to the cxgb4 driver
- A fairly large batch of qib hardware driver changes
- A few fixes for lockdep-detected issues
- A few other miscellaneous fixes and cleanups
Fix up trivial conflict in drivers/net/ethernet/emulex/benet/be.h.
* tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (53 commits)
RDMA/cxgb4: Include vmalloc.h for vmalloc and vfree
IB/mlx4: Fix mlx4_ib_add() error flow
IB/core: Fix IB_SA_COMP_MASK macro
IB/iser: Fix error flow in iser ep connection establishment
IB/mlx4: Increase the number of vectors (EQs) available for ULPs
RDMA/cxgb4: Add query_qp support
RDMA/cxgb4: Remove kfifo usage
RDMA/cxgb4: Use vmalloc() for debugfs QP dump
RDMA/cxgb4: DB Drop Recovery for RDMA and LLD queues
RDMA/cxgb4: Disable interrupts in c4iw_ev_dispatch()
RDMA/cxgb4: Add DB Overflow Avoidance
RDMA/cxgb4: Add debugfs RDMA memory stats
cxgb4: DB Drop Recovery for RDMA and LLD queues
cxgb4: Common platform specific changes for DB Drop Recovery
cxgb4: Detect DB FULL events and notify RDMA ULD
RDMA/cxgb4: Drop peer_abort when no endpoint found
RDMA/cxgb4: Always wake up waiters in c4iw_peer_abort_intr()
mlx4_core: Change bitmap allocator to work in round-robin fashion
RDMA/nes: Don't call event handler if pointer is NULL
RDMA/nes: Fix for the ORD value of the connecting peer
...
|
|
Calling pci_disable_sriov() while VFs are assigned to VMs causes
kernel panic. This patch uses PCI_DEV_FLAGS_ASSIGNED bit state of the
VF's pci_dev to avoid this. Also, the unconditional function reset cmd
issued on a PF probe can delete the VF configuration for the
previously enabled VFs. A scratchpad register is now used to issue a
function reset only when needed (i.e., in a crash dump scenario.)
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Increase MSI-X vectors by 5 for RoCE traffic.
- Add macro to check roce support on a device.
- Add device-specific doorbell and MSI-X vector fields shared with NIC
functionality.
- Provide RoCE driver registration and deregistration functions.
- Add support functions which will be invoked on adapter add/remove
and port up/down events.
- Traverse through the list of adapters to invoke callback functions.
Signed-off-by: Parav Pandit <parav.pandit@emulex.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Skip flashing a FW component if that component is not present in a
particular FW UFI image.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add code to detect UE in case of Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Moves the Emulex driver into drivers/net/ethernet/emulex/ and
make the necessary Kconfig and Makefile changes.
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
