summaryrefslogtreecommitdiff
path: root/drivers/net/usb/asix.c
AgeCommit message (Collapse)Author
2012-07-16asix: Rename asix.c to asix_devices.cChristian Riesch
This patch further creates two additional copies of asix.c. In another patch these copies will be used to factor out common code. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-07asix: avoid copies in tx pathEric Dumazet
I noticed excess calls to skb_copy_expand() or memmove() in asix driver. This driver needs to push 4 bytes in front of frame (packet_len) and maybe add 4 bytes after the end (if padlen is 4) So it should set needed_headroom & needed_tailroom to avoid copies. But its not enough, because many packets are cloned before entering asix_tx_fixup() and this driver use skb_cloned() as a lazy way to check if it can push and put additional bytes in frame. Avoid skb_copy_expand() expensive call, using following rules : - We are allowed to push 4 bytes in headroom if skb_header_cloned() is false (and if we have 4 bytes of headroom) - We are allowed to put 4 bytes at tail if skb_cloned() is false (and if we have 4 bytes of tailroom) TCP packets for example are cloned, but skb_header_release() was called in tcp stack, allowing us to use headroom for our needs. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Allan Chou <allan@asix.com.tw> Cc: Trond Wuellner <trond@chromium.org> Cc: Grant Grundler <grundler@chromium.org> Cc: Paul Stewart <pstew@chromium.org> Cc: Ming Lei <tom.leiming@gmail.com> Tested-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-29asix: allow full size 8021Q frames to be receivedEric Dumazet
asix driver drops 8021Q full size frames because it doesn't take into account VLAN header size. Tested on AX88772 adapter. Signed-off-by: Eric Dumazet <edumazet@google.com> CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org> CC: Allan Chou <allan@asix.com.tw> CC: Trond Wuellner <trond@chromium.org> CC: Grant Grundler <grundler@chromium.org> CC: Paul Stewart <pstew@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-18USB: Disable hub-initiated LPM for comms devices.Sarah Sharp
Hub-initiated LPM is not good for USB communications devices. Comms devices should be able to tell when their link can go into a lower power state, because they know when an incoming transmission is finished. Ideally, these devices would slam their links into a lower power state, using the device-initiated LPM, after finishing the last packet of their data transfer. If we enable the idle timeouts for the parent hubs to enable hub-initiated LPM, we will get a lot of useless LPM packets on the bus as the devices reject LPM transitions when they're in the middle of receiving data. Worse, some devices might blindly accept the hub-initiated LPM and power down their radios while they're in the middle of receiving a transmission. The Intel Windows folks are disabling hub-initiated LPM for all USB communications devices under a xHCI USB 3.0 host. In order to keep the Linux behavior as close as possible to Windows, we need to do the same in Linux. Set the disable_hub_initiated_lpm flag for for all USB communications drivers. I know there aren't currently any USB 3.0 devices that implement these class specifications, but we should be ready if they do. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Hansjoerg Lipp <hjlipp@web.de> Cc: Tilman Schmidt <tilman@imap.cc> Cc: Karsten Keil <isdn@linux-pingi.de> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Jan Dumon <j.dumon@option.com> Cc: Petko Manolov <petkan@users.sourceforge.net> Cc: Steve Glendinning <steve.glendinning@smsc.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com> Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: Brett Rudley <brudley@broadcom.com> Cc: Roland Vossen <rvossen@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com> Cc: Kan Yan <kanyan@broadcom.com> Cc: Dan Williams <dcbw@redhat.com> Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: Herton Ronaldo Krzesinski <herton@canonical.com> Cc: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Chaoming Li <chaoming_li@realsil.com.cn> Cc: Daniel Drake <dsd@gentoo.org> Cc: Ulrich Kunitz <kune@deine-taler.de> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2012-04-24asix: Fix tx transfer padding for full-speed USBIngo van Lil
The asix.c USB Ethernet driver avoids ending a tx transfer with a zero- length packet by appending a four-byte padding to transfers whose length is a multiple of maxpacket. However, the hard-coded 512 byte maxpacket length is valid for high-speed USB only; full-speed USB uses 64 byte packets. Signed-off-by: Ingo van Lil <inguin@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-18Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2012-03-16asix: asix_rx_fixup surgery to reduce skb truesizesEric Dumazet
asix_rx_fixup() is complex, and does some unnecessary memory copies (at least on x86 where NET_IP_ALIGN is 0) Also, it tends to provide skbs with a big truesize (4096+256 with MTU=1500) to upper stack, so incoming trafic consume a lot of memory and I noticed early packet drops because we hit socket rcvbuf too fast. Switch to a different strategy, using copybreak so that we provide nice skbs to upper stack (including the NET_SKB_PAD to avoid future head reallocations in some paths) With this patch, I no longer see packets drops or tcp collapses on various tcp workload with a AX88772 adapter. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Aurelien Jacobs <aurel@gnuage.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Trond Wuellner <trond@chromium.org> Cc: Grant Grundler <grundler@chromium.org> Cc: Paul Stewart <pstew@chromium.org> Reviewed-by: Grant Grundler <grundler@chromium.org> Reviewed-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-11usb: asix: Patch for Sitecom LN-031Joerg Neikes
This patch adds support for the Sitecom LN-031 USB adapter with a AX88178 chip. Added USB id to find correct driver for AX88178 1000 Ethernet adapter. Signed-off-by: Joerg Neikes <j.neikes@midlandgate.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-10asix: fix setting custom MAC address on Asix 88178 devicesJussi Kivilinna
In kernel v3.2 initialization sequence for Asix 88178 devices was changed so that hardware is reseted on every time interface is brought up (ifconfig up), instead just at USB probe time. This causes problem with setting custom MAC address to device as ax88178_reset causes reload of MAC address from EEPROM. This patch fixes the issue by rewriting MAC address at end of ax88178_reset. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: Grant Grundler <grundler@chromium.org> Cc: Allan Chou <allan@asix.com.tw> Cc: stable <stable@vger.kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-10asix: fix setting custom MAC address on Asix 88772 devicesJussi Kivilinna
In kernel v3.2 initialization sequence for Asix 88772 devices was changed so that hardware is reseted on every time interface is brought up (ifconfig up), instead just at USB probe time. This causes problem with setting custom MAC address to device as ax88772_reset causes reload of MAC address from EEPROM. This patch fixes the issue by rewriting MAC address at end of ax88772_reset. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: Grant Grundler <grundler@chromium.org> Cc: Allan Chou <allan@asix.com.tw> Cc: stable <stable@vger.kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: igmp: Avoid zero delay when receiving odd mixture of IGMP queries netdev: make net_device_ops const bcm63xx: make ethtool_ops const usbnet: make ethtool_ops const net: Fix build with INET disabled. net: introduce netif_addr_lock_nested() and call if when appropriate net: correct lock name in dev_[uc/mc]_sync documentations. net: sk_update_clone is only used in net/core/sock.c 8139cp: fix missing napi_gro_flush. pktgen: set correct max and min in pktgen_setup_inject() smsc911x: Unconditionally include linux/smscphy.h in smsc911x.h asix: fix infinite loop in rx_fixup() net: Default UDP and UNIX diag to 'n'. r6040: fix typo in use of MCR0 register bits net: fix sock_clone reference mismatch with tcp memcontrol
2012-01-09usbnet: make ethtool_ops conststephen hemminger
The ethtool_ops table of function pointers should be const. Fix all the usb network drivers. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-07asix: fix infinite loop in rx_fixup()Aurelien Jacobs
At this point if skb->len happens to be 2, the subsequant skb_pull(skb, 4) call won't work and the skb->len won't be decreased and won't ever reach 0, resulting in an infinite loop. With an ASIX 88772 under heavy load, without this patch, rx_fixup() reaches an infinite loop in less than a minute. With this patch applied, no infinite loop even after hours of heavy load. Signed-off-by: Aurelien Jacobs <aurel@gnuage.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-07Merge branch 'driver-core-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core * 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits) arm: fix up some samsung merge sysdev conversion problems firmware: Fix an oops on reading fw_priv->fw in sysfs loading file Drivers:hv: Fix a bug in vmbus_driver_unregister() driver core: remove __must_check from device_create_file debugfs: add missing #ifdef HAS_IOMEM arm: time.h: remove device.h #include driver-core: remove sysdev.h usage. clockevents: remove sysdev.h arm: convert sysdev_class to a regular subsystem arm: leds: convert sysdev_class to a regular subsystem kobject: remove kset_find_obj_hinted() m86k: gpio - convert sysdev_class to a regular subsystem mips: txx9_sram - convert sysdev_class to a regular subsystem mips: 7segled - convert sysdev_class to a regular subsystem sh: dma - convert sysdev_class to a regular subsystem sh: intc - convert sysdev_class to a regular subsystem power: suspend - convert sysdev_class to a regular subsystem power: qe_ic - convert sysdev_class to a regular subsystem power: cmm - convert sysdev_class to a regular subsystem s390: time - convert sysdev_class to a regular subsystem ... Fix up conflicts with 'struct sysdev' removal from various platform drivers that got changed: - arch/arm/mach-exynos/cpu.c - arch/arm/mach-exynos/irq-eint.c - arch/arm/mach-s3c64xx/common.c - arch/arm/mach-s3c64xx/cpu.c - arch/arm/mach-s5p64x0/cpu.c - arch/arm/mach-s5pv210/common.c - arch/arm/plat-samsung/include/plat/cpu.h - arch/powerpc/kernel/sysfs.c and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
2012-01-06Merge branch 'driver-core-next' into Linux 3.2Greg Kroah-Hartman
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file, and it fixes the build error in the arch/x86/kernel/microcode_core.c file, that the merge did not catch. The microcode_core.c patch was provided by Stephen Rothwell <sfr@canb.auug.org.au> who was invaluable in the merge issues involved with the large sysdev removal process in the driver-core tree. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-12-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: net/bluetooth/l2cap_core.c Just two overlapping changes, one added an initialization of a local variable, and another change added a new local variable. Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-23drivers/net/usb/asix: fixed asix_get_wol reported wrong wol status issueallan
Fixed the asix_get_wol() routine reported wrong wol status issue. Signed-off-by: Allan Chou <allan@asix.com.tw> Tested-by: Eugene <elubarsky@gmail.com>; Allan Chou <allan@asix.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-12-19asix: new device idAurelien Jacobs
Adds the device id needed for the USB Ethernet Adapter delivered by ASUS with their Zenbook. Signed-off-by: Aurelien Jacobs <aurel@gnuage.org> Acked-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-18USB: convert drivers/net/* to use module_usb_driver()Greg Kroah-Hartman
This converts the drivers in drivers/net/* to use the module_usb_driver() macro which makes the code smaller and a bit simpler. Added bonus is that it removes some unneeded kernel log messages about drivers loading and/or unloading. Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Samuel Ortiz <samuel@sortiz.org> Cc: Oliver Neukum <oliver@neukum.name> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Petko Manolov <petkan@users.sourceforge.net> Cc: Steve Glendinning <steve.glendinning@smsc.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Dan Williams <dcbw@redhat.com> Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: Herton Ronaldo Krzesinski <herton@canonical.com> Cc: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Chaoming Li <chaoming_li@realsil.com.cn> Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi> Cc: "David S. Miller" <davem@davemloft.net> Cc: Roel Kluin <roel.kluin@gmail.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Jiri Pirko <jpirko@redhat.com> Cc: Pavel Roskin <proski@gnu.org> Cc: Yoann DI-RUZZA <y.diruzza@lim.eu> Cc: George <george0505@realtek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-15net-next:asix: V2 Update VERSIONGrant Grundler
Only update VERSION to reflect previous changes. Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-15net-next:asix: V2 more fixes for ax88178 phy init sequenceGrant Grundler
Now works on Samsung Series 5 (chromebook) Two fixes here: o use 0x7F mask for phymode o read phyid *AFTER* phy is powered up (via GPIOs) Signed-off-by: Allan Chou <allan@asix.com.tw> Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-15net-next:asix: reduce AX88772 init time by about 2 secondsGrant Grundler
ax88772_reset takes about 2 seconds and is called twice. Once from ax88772_bind() directly and again indirectly from usbnet_open(). Reset the USB FW/Phy enough to blink the LEDs when inserted. Signed-off-by: Allan Chou <allan@asix.com.tw> Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-15net-next:asix:poll in asix_get_phyid in case phy not readyGrant Grundler
Sometimes the phy isn't ready after reset...poll and pray it will be soon. Signed-off-by: Freddy Xin <freddy@asix.com.tw> Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-15net-next:asix:PHY_MODE_RTL8211CL should be 0xCGrant Grundler
Use correct value for rtl phy support. (rtl phy are in AX88178 devices like NWU220G and USB2-ET1000). Signed-off-by: Allan Chou <allan@asix.com.tw> Tested-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-19NET: asix: fix ethtool -e for AX88178 USB dongleGrant Grundler
"ethtool -e ethX" dumps EEPROM data. Patch sets EEPROM length for device. Ethtool works alot better when the kernel believes the length is > 0. From: Allan Chou <allan@asix.com.tw> Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-04NET: white space/coding style cleanup of asix driverGrant Grundler
check patch was complaining...mostly replaced: if ((ret = asix_foo(xx)) < 0) ... with ret = asix_foo(xx); if (ret < 0) ... Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-04NET: fix phy init for Asix AX88178 USB (GigE)Grant Grundler
Asix provided this patch and I've confirmed "Plugable USB2-E1000" and "Shenzhen Winstars NWU220G" USB dongles can get a link and TX/RX data. Signed-off-by: "Freddy Xin" <freddy@asix.com.tw> Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-04NET: fix phy init for AX88772 USB ethernetGrant Grundler
Fix phy initialization for AX88772 (USB 2.0 100BT). Failure was occasionally DHCP wouldn't work after reboot or suspend/resume cycle. Remove MONITOR_MODE. In this mode, Received packets are not buffered when the remote wakeup is enabled. Signed-off-by: "Freddy Xin" <freddy@asix.com.tw> Signed-off-by: Grant Grundler <grundler@chromium.org> Acked-by: Olof Johansson <olofj@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-17net: remove use of ndo_set_multicast_list in driversJiri Pirko
replace it by ndo_set_rx_mode Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27ASIX: Use only 11 bits of header for data sizeMarek Vasut
The AX88772B uses only 11 bits of the header for the actual size. The other bits are used for something else. This causes dmesg full of messages: asix_rx_fixup() Bad Header Length This patch trims the check to only 11 bits. I believe on older chips, the remaining 5 top bits are unused. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27ASIX: Simplify condition in rx_fixup()Marek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-21ASIX: Add AX88772B USB IDMarek Vasut
This device can be found in Acer Iconia TAB W500 tablet dock. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-29ethtool: Call ethtool's get/set_settings callbacks with cleaned dataDavid Decotigny
This makes sure that when a driver calls the ethtool's get/set_settings() callback of another driver, the data passed to it is clean. This guarantees that speed_hi will be zeroed correctly if the called callback doesn't explicitely set it: we are sure we don't get a corrupted speed from the underlying driver. We also take care of setting the cmd field appropriately (ETHTOOL_GSET/SSET). This applies to dev_ethtool_get_settings(), which now makes sure it sets up that ethtool command parameter correctly before passing it to drivers. This also means that whoever calls dev_ethtool_get_settings() does not have to clean the ethtool command parameter. This function also becomes an exported symbol instead of an inline. All drivers visible to make allyesconfig under x86_64 have been updated. Signed-off-by: David Decotigny <decot@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-17asix: add USB ID for Logitec LAN-GTJ U2AArnaud Ebalard
Logitec LAN-GTJ U2A (http://www.pro.logitec.co.jp/pro/g/gLAN-GTJU2A/) USB 2.0 10/10/1000 Ethernet adapter is based on ASIX AX88178 chipset. This patch adds missing USB ID for the device. Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-11Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
2010-06-07asix: check packet size against mtu+ETH_HLEN instead of ETH_FRAME_LENJussi Kivilinna
Driver checks received packet is too large in asix_rx_fixup() and fails if it is. Problem is that MTU might be set larger than 1500 and asix fails to work correctly with VLAN tagged packets. The check should be 'dev->net->mtu + ETH_HLEN' instead. Tested with AX88772. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-03drivers/net: use __packed annotationEric Dumazet
cleanup patch. Use new __packed annotation in drivers/net/ Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-25drivers/net/usb/asix.c: Fix pointer cast.David S. Miller
Stephen Rothwell reports the following new warning: drivers/net/usb/asix.c: In function 'asix_rx_fixup': drivers/net/usb/asix.c:325: warning: cast from pointer to integer of different size drivers/net/usb/asix.c:354: warning: cast from pointer to integer of different size The code just cares about the low alignment bits, so use an "unsigned long" cast instead of one to "u32". Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17drivers/net/usb: Use kmemdupJulia Lawall
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17drivers/net/usb/asix.c: Fix unaligned accessesNeil Jones
Using this driver can cause unaligned accesses in the IP layer This has been fixed by aligning the skb data correctly using the spare room left over by the 4 byte header inserted between packets by the device. Signed-off-by: Neil Jones <NeilJay@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-11Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/stmmac/stmmac_main.c drivers/net/wireless/wl12xx/wl1271_cmd.c drivers/net/wireless/wl12xx/wl1271_main.c drivers/net/wireless/wl12xx/wl1271_spi.c net/core/ethtool.c net/mac80211/scan.c
2010-04-03net: convert multicast list to list_headJiri Pirko
Converts the list and the core manipulating with it to be the same as uc_list. +uses two functions for adding/removing mc address (normal and "global" variant) instead of a function parameter. +removes dev_mcast.c completely. +exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for manipulation with lists on a sandbox (used in bonding and 80211 drivers) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-30include cleanup: Update gfp.h and slab.h includes to prepare for breaking ↵Tejun Heo
implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-10asix: fix setting mac address for AX88772Jussi Kivilinna
Setting new MAC address only worked when device was set to promiscuous mode. Fix MAC address by writing new address to device using undocumented command AX_CMD_READ_NODE_ID+1. Patch is tested with AX88772 device. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: David Hollis <dhollis@davehollis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-18net/usb: convert to use netdev_for_each_mc_addrJiri Pirko
also removed needless checks in smsc95xx Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-17usbnet: Convert dev(dbg|err|warn|info) macros to netdev_<level>Joe Perches
These macros are too similar to the dev_<level> equivalents but take a usbnet * argument. Convert them to the recently introduced netdev_<level> macros and remove the old macros. The old macros had "\n" appended to the format string. Add the "\n" to the converted uses. Some existing uses of the dev<foo> macros in cdc_eem.c probably mistakenly had trailing "\n". No "\n" added there. Fix net1080 this/other log message inversion. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-12net: use netdev_mc_count and netdev_mc_empty when appropriateJiri Pirko
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss anything). Used spatch and did small tweaks and conding style changes when it was suitable. Jirka Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03drivers/net: Move && and || to end of previous lineJoe Perches
Only files where David Miller is the primary git-signer. wireless, wimax, ixgbe, etc are not modified. Compile tested x86 allyesconfig only Not all files compiled (not x86 compatible) Added a few > 80 column lines, which I ignored. Existing checkpatch complaints ignored. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-10usbnet: Set link down initially for drivers that update link stateBen Hutchings
Some usbnet drivers update link state while others do not due to hardware limitations. Add a flag to distinguish those that do, and set the link down initially for their devices. This is intended to fix this bug: http://bugs.debian.org/444043 Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02netdev: drivers should make ethtool_ops constStephen Hemminger
No need to put ethtool_ops in data, they should be const. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.0.4) at 2024-05-23 02:02:21 +0000