summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath5k/base.c
AgeCommit message (Collapse)Author
2009-04-22atheros: put atheros wireless drivers into ath/Luis R. Rodriguez
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath5k: use regulatory infrastructureBob Copeland
Make ath5k select the ath module and add in the hooks to make the eeprom regulatory hint and reg notifier take effect. Changes to attach.c Changes-licensed-under: ISC Changes to base.c Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-22ath5k: reduce exported channel listBob Copeland
Claiming every available 5 ghz channel has a couple of negative side-effects: scanning takes a long time, and the channel list overflows the available buffer space for netlink commands, resulting in: $ iw phy phy0 info command failed: No buffer space available (-105) This patch adds a modparam so people who want to see all the channels can do so by passing all_channels=1. By default users will see a smaller list of channels. This also halves scan time, from 10 seconds down to less than 5 when using world regulatory. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Reported-by: Simon Farnsworth <simon@farnz.org.uk> Tested-By: Simon Farnsworth <simon@farnz.org.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-04-07dma-mapping: replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)Yang Hongyang
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32) Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-27ath5k: properly drop packets from ops->txBob Copeland
We shouldn't return NETDEV_TX_BUSY from the TX callback, especially after we've mucked with the sk_buffs. Drop the packets and return NETDEV_TX_OK. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27ath5k: warn and correct rate for unknown hw rate indexesBob Copeland
ath5k sets up a mapping table from the hardware rate index to the rate index used by mac80211; however, we have seen some received frames with incorrect rate indexes. Such frames normally get dropped with a warning in __ieee80211_rx(), but it doesn't include enough information to track down the error. This patch adds a warning to hw_to_driver_rix for any lookups that result in a rate index of -1, then returns a valid rate so the frame can be processed. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27ath5k: Add tx power calibration supportNick Kossifidis
* Add tx power calibration support * Add a few tx power limits * Hardcode default power to 12.5dB * Disable TPC for now v2: Address Jiri's comments Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27ath5k: remove dummy PCI "retry timeout" fixBob Copeland
Remove the PCI retry timeout code, for all the same reasons that Luis Rodriguez removed it for ath9k. Changes-licensed-under: 3-Clause-BSD Cc: Luis Rodriguez <lrodriguez@atheros.com> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-27ath5k: disable MIB interruptsBob Copeland
The MIB interrupt fires whenever counters overflow; however without support for automatic noise immunity, we can sometimes get an interrupt storm. The get_stats() callback reads the counters anyway so we can disable the interrupt for now until ANI is implemented. This fixes the issue reported in http://bugzilla.kernel.org/show_bug.cgi?id=12647. Changes-licensed-under: 3-Clause-BSD Cc: stable@kernel.org Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16ath5k: extract LED code into a separate fileBob Copeland
Move LED code out of base.c for clarity. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-16ath5k: constify stuffJiri Slaby
Make some structures const to place them in .rodata, since we won't change them. Most important parts of objdump -h: - 0 .text 00011170 + 0 .text 00011140 - 5 .rodata 0000828e + 5 .rodata 0000895e - 13 .data 00000560 + 13 .data 00000110 - 14 .devinit.data 00000260 Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Cc: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05ath5k: fix hw rate index conditionJiri Slaby
Make sure we print out a warning when the index is out of bounds, i.e. even on hw_rix == AR5K_MAX_RATES. Also change to WARN and print text with the reported hw_rix. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Nick Kossifidis <mickflemm@gmail.com> Cc: Luis R. Rodriguez <lrodriguez@atheros.com> Cc: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath5k: compute rts/cts duration after computing full pktlenBob Copeland
RTS and CTS-to-self duration needs to go after ICV len is considered. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath5k: move beacon processing to a taskletBob Copeland
We currently send beacons directly from the interrupt routine. This can hold up interrupt processing in beaconing modes and makes the ISR somewhat more complex. Move it to a tasklet like rx and tx. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath5k: use spin_lock_irqsave for beacon lockBob Copeland
ath5k_reset can be called from process context, which in turn can call ath5k_beacon_config which takes the sc->block spinlock. Since it can also be taken in hard irq context, use spin_lock_irqsave everywhere. This fixes a potential deadlock in adhoc mode. Changes-licensed-under: 3-Clause-BSD Cc: stable@kernel.org Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath5k: don't mask off interrupt bitsBob Copeland
Since interrupts are already masked by the hardware, there's no need to discard interrupt bits in the ISR itself. Also, in ath5k_beacon_config we mask off a couple of bits without locking, so doing this mask in software can lead to unhandled beacon timer and beacon miss interrupts. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-13ath5k: Don't call reset on config_interfaceNick Kossifidis
* We call reset too often and this can result various PHY problems. On config_interface we don't need to reset the whole device. TODO: Create a function hw_fast_reset that only resets the PCU (tx/rx stuff) and not the whole device so that we can use this for stuck beacons etc. Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-13ath5k: Disable BMISS interruptsNick Kossifidis
* Don't enable BMISS interrupts as we don't handle them yet Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-13ath5k: Update gain_F calibration code and add documentationNick Kossifidis
* Update and cleanup rf gain optimization code * Add comments and refferences to docs and use sane function names * Use only step index on ath5k_gain, no need to have a pointer to the current step since we can determine te step from it's index, this also allows us to put all other structs on rfgain.h and cleanup ath5k.h a little * No need for ah_rfgain variable, we use ah_gain.g_state for everything * Tested on RF2112B chip but gain_F calibration is not yet done (we will finish this on the next patch where we'll rewrite rf-buffer handling) * Use initial rf gain settings for 2316 and 2317 SoCs introduced on a previous patch It seems big but it's mostly cleanup, very few functional changes have been made on phy.c Signed-off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-09ath5k: properly free rx dma descriptorsFelix Fietkau
When freeing rx dma descriptors, use the right buffer size. Fixes kernel oopses on module unload on ixp4xx and most likely other platforms as well. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-03Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2009-01-29ath5k: fix locking in ath5k_configBob Copeland
ath5k_config updates the software context without taking sc->lock. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: support LED's on emachines E510 notebookTulio Magno Quites Machado Filho
Add vendor ID for AMBIT and use it to set the ath5k LED gpio. base.c: Changes-licensed-under: 3-Clause-BSD Signed-off-by: Tulio Magno Quites Machado Filho <tuliom@gmail.com> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29mac80211: Generic TSF debuggingAlina Friedrichsen
This patch enables low-level driver independent debugging of the TSF and remove the driver specific things of ath5k and ath9k from the debugfs. Signed-off-by: Alina Friedrichsen <x-alina@gmx.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: honor the RTS/CTS bitsBob Copeland
The ath5k driver didn't use set_rts_threshold or use_cts_prot, and also didn't check the IEEE80211_TX_RC_USE_{RTS_CTS,CTS_PROTECT} RC flags. Tell the hardware about these so RTS/CTS will work, and so the device will work better in mixed b/g environments. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: use short preamble when possibleBob Copeland
ath5k previously ignored TX_RC_SHORT_PREAMBLE and did not use config->use_short_preamble, so the long preamble was always used for transmitted packets. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: remove stop/start calls from within suspend/resumeBob Copeland
mac80211 now takes down interfaces automatically during suspend so doing it in the driver is unnecessary. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: fix bf->skb==NULL panic in ath5k_tasklet_rxBob Copeland
Under memory pressure, we may not be able to allocate a new skb for new packets. If the allocation fails, ath5k_tasklet_rx will exit but will leave a buffer in the list with a NULL skb, eventually triggering a BUG_ON. Extract the skb allocation from ath5k_rxbuf_setup() and change the tasklet to allocate the next skb before accepting a packet. Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29ath5k: support LEDs on Acer Aspire One netbookBob Copeland
Add vendor ID for Foxconn and use it to set the ath5k LED gpio and polarity for Acer branded laptops. base.c: Changes-licensed-under: 3-Clause-BSD Reported-by: Maxim Levitsky <maximlevitsky@gmail.com> Tested-by: Maxim Levitsky <maximlevitsky@gmail.com> Tested-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-29mac80211: clean up set_key callbackJohannes Berg
The set_key callback now seems rather odd, passing a MAC address instead of a station struct, and a local address instead of a vif struct. Change that. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Bob Copeland <me@bobcopeland.com> [ath5k] Acked-by: Ivo van Doorn <ivdoorn@gmail.com> [rt2x00] Acked-by: Christian Lamparter <chunkeey@web.de> [p54] Tested-by: Kalle Valo <kalle.valo@nokia.com> [iwl3945] Tested-by: Samuel Ortiz <samuel@sortiz.org> [iwl3945] Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-12ath5k: fix return values from ath5k_txBob Copeland
Should return NETDEV_TX_{OK,BUSY} instead of 0,-1 (this doesn't change any current functionality). Changes-licensed-under: 3-Clause-BSD Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19ath5k: correct packet length in tx descriptorsBob Copeland
Packet length calculation (which includes frame check sequence) should take into account whether we add a pad field or not. Extract the calculation into a helper and use it in both places. Changes to desc.c Changes-licensed-under: ISC Changes to ath5k.h, base.c Changes-licensed-under: 3-Clause-BSD Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19ath5k: fix 802.11 header padding on RX, unpadding on TXBenoit PAPILLAULT
Padding the 802.11 header to a multiple of 4 bytes needs to be done only for frames with a body. This fixes a bug where 2 bytes were missing in monitor mode for ACK frames. Inspired by a patch from Jouni Malinen on ath9k. Ref: http://bugzilla.kernel.org/show_bug.cgi?id=12101 : Signed-off-by: Benoit Papillault <benoit.papillault@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-26Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/hp-plus.c drivers/net/wireless/ath5k/base.c drivers/net/wireless/ath9k/recv.c net/wireless/reg.c
2008-11-26ath5k: set mac address in add_interfaceBob Copeland
Configure the mac address in add_interface and clear it in remove_interface so that users can change the mac address to something other than the one in the eeprom. Also avoid setting it at attach time so that we won't ack packets until fully set up. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-25ath5k: name pci driver "ath5k" tooJohannes Berg
Call the ath5k pci driver struct "ath5k" too to be less confusing in sysfs. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-25ath5k: disable beacon filter when station is not associatedMartin Xu
Ath5k driver has too many interrupts per second at idle http://bugzilla.kernel.org/show_bug.cgi?id=11749 Signed-off-by: Martin Xu <martin.xu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21ath5k: allow APs to receive beaconsLuis R. Rodriguez
Allow APs to receive beacons to detect when it needs to use protection to update the NAV correctly on 11b stations. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21ath5k: Fix IMR initNick Kossifidis
*On a previous patch i splitted AR5K_INT_TX to multiple different TX interrupt flags for better handling but i forgot to unmask the new TXDESC and TXEOL interrupts on ath5k_init and only left TXOK. However for each queue we enable TXDESC and TXEOL interrupts, not TXOK so we don't handle TX interrupts at all (because these interrupts remain masked on PISR) and under load it results packet loss. Fix the problem by unmasking TXDESC and TXEOL on ath5k_init. Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-10ath5k: update keycache to support TKIP handlingBob Copeland
Newer parts have slots at entry+64 for michael mic and can do WPA-TKIP in hardware. The open-sourced Atheros HAL has code for accessing this portion so now we know how where to put the key material. Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-10ath5k: enable hardware encryption for WEPBob Copeland
This change re-enables hardware encryption for ath5k after setting up mac80211 to handle the initialization vectors which happens to make it work. Add a module param (nohwcrypt) to optionally turn it off. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-06Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/wireless/ath5k/base.c net/8021q/vlan_core.c
2008-11-06Revert "ath5k: honor FIF_BCN_PRBRESP_PROMISC in STA mode"John W. Linville
Unfortunately, the result was that mac80211 didn't see all the beacons it actually wanted to see. This caused lost associations. Hopefully we can revisit this when mac80211 is less greedy about seeing beacons directly... This reverts commit 063279062a8c530cc90fb77797db16c49c905b26. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31ath5k: Update interrupt masking codeNick Kossifidis
*Properly get/set all available ISR/IMR values and review common/uncommon bits *Better handling of per-txq interrupts (we can now resolve what q is generating each interrupt -this will help in debuging wme later) *Some minor updates from legacy-hal *Properly handle RXNOFRM and TXNOFRM interrupt masking (even when we don't set them on IMR they keep showing up, so we disable them by zeroing AR5K_RXNOFRM and AR5K_TXNOFRM registers). This doesn't exist on legacy-hal but i've tested it on various cards and it works fine. Changes-Licensed-under: ISC Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31ath5k: reduce checkpatch.pl errorsJohn Daiker
A few changes to reduce checkpatch.pl errors in the ath5k driver. For the most part, I only fixed cosmetic things, and left the actual 'code flow' untouched (hopefully)! Diff is against wireless-testing HEAD. Signed-off-by: John Daiker <daikerjohn@gmail.com> Reviewed-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31mac80211/drivers: rewrite the rate control APIJohannes Berg
So after the previous changes we were still unhappy with how convoluted the API is and decided to make things simpler for everybody. This completely changes the rate control API, now taking into account 802.11n with MCS rates and more control, most drivers don't support that though. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31ath5k: fix mesh point operationAndrey Yurovsky
This patch fixes mesh point operation (thanks to YanBo for pointing out the problem): make mesh point interfaces start beaconing when they come up and configure the RX filter in mesh mode so that mesh beacons and action frames are received. Add mesh point to the check in ath5k_add_interface. Tested with multiple AR5211 cards. Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31ath5k: correct ath5k signal qualityLuis R. Rodriguez
This adjusts ath5k's signal quality reporting taking into consideration received beacons at an RSSI of 35 should indicate you can use of 54 Mbps on a single stream card (all ath5k cards) reliably. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31Ath5k: add AP modeJiri Slaby
Add support for AP mode. This involves: - enablement in ath5k_beacon_config -- initialize beacon timer - add AP to the supported modes in ath5k_add_interface - handle beacon change even for AP in ath5k_config_interface - remove useless test for IBSS in ath5k_beacon_update Note that it doesn't enable the AP mode for the driver. It must be enabled by NL80211_IFTYPE_AP bit added to interface_modes. v2: Fixed opmode constant (IEEE80211_ to NL80211_) Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Nick Kossifidis <mickflemm@gmail.com> Cc: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-10-31mac80211: introduce hw config change flagsJohannes Berg
This makes mac80211 notify the driver which configuration actually changed, e.g. channel etc. No driver changes, this is just plumbing, driver authors are expected to act on this if they want to. Also remove the HW CONFIG debug printk, it's incorrect, often we configure something else. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-05-27 00:53:52 +0000