summaryrefslogtreecommitdiff
path: root/drivers/s390/net/qeth_l2_main.c
AgeCommit message (Collapse)Author
2019-11-20s390/qeth: invoke softirqs after napi_schedule()Julian Wiedmann
[ Upstream commit 4d19db777a2f32c9b76f6fd517ed8960576cb43e ] Calling napi_schedule() from process context does not ensure that the NET_RX softirq is run in a timely fashion. So trigger it manually. This is no big issue with current code. A call to ndo_open() is usually followed by a ndo_set_rx_mode() call, and for qeth this contains a spin_unlock_bh(). Except for OSN, where qeth_l2_set_rx_mode() bails out early. Nevertheless it's best to not depend on this behaviour, and just fix the issue at its source like all other drivers do. For instance see commit 83a0c6e58901 ("i40e: Invoke softirqs after napi_reschedule"). Fixes: a1c3ed4c9ca0 ("qeth: NAPI support for l2 and l3 discipline") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-06-25s390/qeth: fix VLAN attribute in bridge_hostnotify udev eventAlexandra Winter
[ Upstream commit 335726195e460cb6b3f795b695bfd31f0ea70ef0 ] Enabling sysfs attribute bridge_hostnotify triggers a series of udev events for the MAC addresses of all currently connected peers. In case no VLAN is set for a peer, the device reports the corresponding MAC addresses with VLAN ID 4096. This currently results in attribute VLAN=4096 for all non-VLAN interfaces in the initial series of events after host-notify is enabled. Instead, no VLAN attribute should be reported in the udev event for non-VLAN interfaces. Only the initial events face this issue. For dynamic changes that are reported later, the device uses a validity flag. This also changes the code so that it now sets the VLAN attribute for MAC addresses with VID 0. On Linux, no qeth interface will ever be registered with VID 0: Linux kernel registers VID 0 on all network interfaces initially, but qeth will drop .ndo_vlan_rx_add_vid for VID 0. Peers with other OSs could register MACs with VID 0. Fixes: 9f48b9db9a22 ("qeth: bridgeport support - address notifications") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2018-10-10s390/qeth: don't dump past end of unknown HW headerJulian Wiedmann
[ Upstream commit 0ac1487c4b2de383b91ecad1be561b8f7a2c15f4 ] For inbound data with an unsupported HW header format, only dump the actual HW header. We have no idea how much payload follows it, and what it contains. Worst case, we dump past the end of the Inbound Buffer and access whatever is located next in memory. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-31s390/qeth: free netdevice when removing a cardJulian Wiedmann
[ Upstream commit 6be687395b3124f002a653c1a50b3260222b3cd7 ] On removal, a qeth card's netdevice is currently not properly freed because the call chain looks as follows: qeth_core_remove_device(card) lx_remove_device(card) unregister_netdev(card->dev) card->dev = NULL !!! qeth_core_free_card(card) if (card->dev) !!! free_netdev(card->dev) Fix it by free'ing the netdev straight after unregistering. This also fixes the sysfs-driven layer switch case (qeth_dev_layer2_store()), where the need to free the current netdevice was not considered at all. Note that free_netdev() takes care of the netif_napi_del() for us too. Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-17s390/qeth: fix GSO throughput regressionJulian Wiedmann
[ Upstream commit 6d69b1f1eb7a2edf8a3547f361c61f2538e054bb ] Using GSO with small MTUs currently results in a substantial throughput regression - which is caused by how qeth needs to map non-linear skbs into its IO buffer elements: compared to a linear skb, each GSO-segmented skb effectively consumes twice as many buffer elements (ie two instead of one) due to the additional header-only part. This causes the Output Queue to be congested with low-utilized IO buffers. Fix this as follows: If the MSS is low enough so that a non-SG GSO segmentation produces order-0 skbs (currently ~3500 byte), opt out from NETIF_F_SG. This is where we anticipate the biggest savings, since an SG-enabled GSO segmentation produces skbs that always consume at least two buffer elements. Larger MSS values continue to get a SG-enabled GSO segmentation, since 1) the relative overhead of the additional header-only buffer element becomes less noticeable, and 2) the linearization overhead increases. With the throughput regression fixed, re-enable NETIF_F_SG by default to reap the significant CPU savings of GSO. Fixes: 5722963a8e83 ("qeth: do not turn on SG per default") Reported-by: Nils Hoppmann <niho@de.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-17s390/qeth: build max size GSO skbs on L2 devicesJulian Wiedmann
[ Upstream commit 0cbff6d4546613330a1c5f139f5c368e4ce33ca1 ] The current GSO skb size limit was copy&pasted over from the L3 path, where it is needed due to a TSO limitation. As L2 devices don't offer TSO support (and thus all GSO skbs are segmented before they reach the driver), there's no reason to restrict the stack in how large it may build the GSO skbs. Fixes: d52aec97e5bc ("qeth: enable scatter/gather in layer 2 mode") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-18s390/qeth: use skb_cow_head() for L2 OSA xmitJulian Wiedmann
Taking a full copy via skb_realloc_headroom() on every xmit is overkill and wastes CPU time; all we actually need is to push on the qeth_hdr. So rework the L2 OSA TX path to avoid the copy. Minor complications arise because struct qeth_hdr must not cross a page boundary. So add a new helper qeth_push_hdr() that catches this, and falls back to the hdr cache that we already use for IQDs. This change uncovered that qeth's TX completion takes rather long. Now that we no longer free the original skb straight away and thus call skb->destructor later than before, throughput regresses significantly. For now, restore old behaviour by adding an explicit skb_orphan(), and a big TODO to improve the TX completion time. Tested-by: Nils Hoppmann <niho@de.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-18s390/qeth: pass full IQD header length to fill_buffer()Julian Wiedmann
This is a prerequisite for unifying the code to build header elements. The TSO header has a different size, so we can no longer rely on implicitly adding the size of a normal qeth_hdr. No functional change. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-18s390/qeth: pass TSO data offset to fill_buffer()Julian Wiedmann
For TSO we need to skip the skb's qeth/IP/TCP headers when mapping it into buffer elements. Instead of (mis)using skb_pull(), pass a corresponding offset to fill_buffer() like we already do for IQDs. No actual change in the resulting TSO buffers. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-18s390/qeth: pass TSO header length to fill_buffer()Julian Wiedmann
The TSO code already calculates the length of its header element, no need to duplicate this in the low-level code again. Use this opportunity to make hd_len unsigned, and for TSO match its calculation to what tso_fill_header() does. No functional change. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-18s390/qeth: pass full data length to l2_fill_header()Julian Wiedmann
For IQD we already need to fix up the qeth_hdr's length field, and future changes will require more flexibility for OSA as well. The device-specific path knows best what header length it requires, so just pass it from there. While at it, remove the unused qeth_card parameter. No functional change. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-18s390/qeth: split L2 xmit pathsJulian Wiedmann
l2_hard_start_xmit() actually doesn't contain much shared code, and having device-specific paths makes isolated changes a lot easier. So split it into three routines for IQD, OSN and OSD/OSM/OSX. No functional change. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-15s390/qeth: extract bridgeport cmd builderJulian Wiedmann
Consolidation of duplicated code, no functional change. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-15s390/net: reduce inliningJulian Wiedmann
Clean up the inline cruft in s390 net drivers. Many of the inlined functions had only one caller anyway. Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-15s390/qeth: make more use of skb APIJulian Wiedmann
Replace some open-coded parts with their proper API calls. Also remove two skb_[re]set_mac_header() calls in the L2 xmit paths that are clearly no longer required, since at least commit 6d1ccff62780 ("net: reset mac header in dev_start_xmit()"). Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-15s390/qeth: remove extra L2 adapterparms queryJulian Wiedmann
qeth_l2_request_initial_mac() queries the device for its supported adapterparms, even though they already have been queried as part of the device's high-level setup. Remove that extra call. The only call chain for qeth_l2_request_initial_mac() is __qeth_l2_set_online() qeth_core_hardsetup_card() qeth_query_setadapterparms() qeth_l2_setup_netdev() qeth_l2_request_initial_mac() qeth_query_setadapterparms() , and we only reach qeth_l2_request_initial_mac() if the first adapterparms query succeeds. Hence removing the second query results in no loss of functionality. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-15s390/qeth: don't access skb after transmissionJulian Wiedmann
After transmitting a skb via send_packet[_fast](), the statistics code accesses the skb once more to account for transmitted page frags. This has a (theoretical?) race against the TX completion - if the TX completion is processed and frees the skb before hard_start_xmit() gets to the statistics part, we access random memory. Fix this by caching the # of page frags, before the skb is transmitted. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-20s390/qeth: use diag26c to get MAC address on L2Julian Wiedmann
When a s390 guest runs on a z/VM host that's part of a SSI cluster, it can be migrated to a different host. In this case, the MAC address it originally obtained on the old host may be re-assigned to a new guest. This would result in address conflicts between the two guests. When running as z/VM guest, use the diag26c MAC Service to obtain a hypervisor-managed MAC address. The MAC Service is SSI-aware, and won't re-assign the address after the guest is migrated to a new host. This patch adds support for the z/VM MAC Service on L2 devices. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-20s390/qeth: add ipa return codes for bridgeportKittipon Meesompop
add ipa return codes for Bridgeport (HiperSockets and OSA) according to system level design. Signed-off-by: Kittipon Meesompop <kmeesomp@linux.vnet.ibm.com> Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16networking: make skb_push & __skb_push return void pointersJohannes Berg
It seems like a historic accident that these return unsigned char *, and in many places that means casts are required, more often than not. Make these functions return void * and remove all the casts across the tree, adding a (u8 *) cast only where the unsigned char pointer was used directly, all done with the following spatch: @@ expression SKB, LEN; typedef u8; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - *(fn(SKB, LEN)) + *(u8 *)fn(SKB, LEN) @@ expression E, SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; type T; @@ - E = ((T *)(fn(SKB, LEN))) + E = fn(SKB, LEN) @@ expression SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - fn(SKB, LEN)[0] + *(u8 *)fn(SKB, LEN) Note that the last part there converts from push(...)[0] to the more idiomatic *(u8 *)push(...). Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-06s390/qeth: log bridgeport capabilitiesJulian Wiedmann
Bridgeport is a l2-specific feature, and we should write its capabilities to a debug entry. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-11s390/qeth: avoid null pointer dereference on OSNJulian Wiedmann
Access card->dev only after checking whether's its valid. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-11s390/qeth: unbreak OSM and OSN supportJulian Wiedmann
commit b4d72c08b358 ("qeth: bridgeport support - basic control") broke the support for OSM and OSN devices as follows: As OSM and OSN are L2 only, qeth_core_probe_device() does an early setup by loading the l2 discipline and calling qeth_l2_probe_device(). In this context, adding the l2-specific bridgeport sysfs attributes via qeth_l2_create_device_attributes() hits a BUG_ON in fs/sysfs/group.c, since the basic sysfs infrastructure for the device hasn't been established yet. Note that OSN actually has its own unique sysfs attributes (qeth_osn_devtype), so the additional attributes shouldn't be created at all. For OSM, add a new qeth_l2_devtype that contains all the common and l2-specific sysfs attributes. When qeth_core_probe_device() does early setup for OSM or OSN, assign the corresponding devtype so that the ccwgroup probe code creates the full set of sysfs attributes. This allows us to skip qeth_l2_create_device_attributes() in case of an early setup. Any device that can't do early setup will initially have only the generic sysfs attributes, and when it's probed later qeth_l2_probe_device() adds the l2-specific attributes. If an early-setup device is removed (by calling ccwgroup_ungroup()), device_unregister() will - using the devtype - delete the l2-specific attributes before qeth_l2_remove_device() is called. So make sure to not remove them twice. What complicates the issue is that qeth_l2_probe_device() and qeth_l2_remove_device() is also called on a device when its layer2 attribute changes (ie. its layer mode is switched). For early-setup devices this wouldn't work properly - we wouldn't remove the l2-specific attributes when switching to L3. But switching the layer mode doesn't actually make any sense; we already decided that the device can only operate in L2! So just refuse to switch the layer mode on such devices. Note that OSN doesn't have a layer2 attribute, so we only need to special-case OSM. Based on an initial patch by Ursula Braun. Fixes: b4d72c08b358 ("qeth: bridgeport support - basic control") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-11s390/qeth: handle sysfs error during initializationUrsula Braun
When setting up the device from within the layer discipline's probe routine, creating the layer-specific sysfs attributes can fail. Report this error back to the caller, and handle it by releasing the layer discipline. Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> [jwi: updated commit msg, moved an OSN change to a subsequent patch] Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-11s390/qeth: convert to ETHTOOL_GLINKSETTINGS APIJulian Wiedmann
get_settings() is deprecated and lacks support for higher link speeds, so implement get_link_ksettings() instead. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-11s390/qeth: use and remove some definesJulian Wiedmann
1. a buffer has 16 is_header flags, because that's its # of elements 2. replace the last occurrence of QETH_HEADER_SIZE, and remove it Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-11s390/qeth: use correct return type for hard_start_xmit()Julian Wiedmann
ndo_start_xmit() expects us to return netdev_tx_t here... Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-11s390/qeth: remove unused parameterJulian Wiedmann
'elements_needed' is not used in qeth_do_send_packet_fast(), so consequently remove it. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-11s390/qeth: move gdev shutdown handler to coreJulian Wiedmann
Duplicated code. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-11s390/qeth: move NAPI poll routine to coreJulian Wiedmann
Identical code, we just need to call a layer-specific hook to process any received buffer. qeth_buffer_reclaim_work() is shuffled around to avoid a forward declaration for qeth_queue_input_buffer(). Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-11s390/qeth: move common ioctl handling to coreJulian Wiedmann
There's a number of layer-independent ioctls that we can handle in core, and reduce code duplication. For layer-specific ioctls, add a do_ioctl() discipline hook. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-07s390/qeth: Remove unused codeJulian Wiedmann
1. options.add_hhlen is set but never used, drop it 2. clean up no longer required forward declarations 3. delete all sorts of unused defines Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-24s390/qeth: size calculation outbound buffersJulian Wiedmann
Depending on the device type, hard_start_xmit() builds different output buffer formats. For instance with HiperSockets, on both L2 and L3 we strip the ETH header from the skb - L3 doesn't need it, and L2 carries it in the buffer's header element. For this, we pass data_offset = ETH_HLEN all the way down to __qeth_fill_buffer(), where skb->data is then adjusted accordingly. But the initial size calculation still considers the *full* skb length (including the ETH header). So qeth_get_elements_no() can erroneously reject a skb as too big, even though it would actually fit into an output buffer once the ETH header has been trimmed off later. Fix this by passing an additional offset to qeth_get_elements_no(), that indicates where in the skb the on-wire data actually begins. Since the current code uses data_offset=-1 for some special handling on OSA, we need to clamp data_offset to 0... On HiperSockets this helps when sending ~MTU-size skbs with weird page alignment. No change for OSA or AF_IUCV. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-12s390/qeth: issue STARTLAN as first IPA commandJulian Wiedmann
STARTLAN needs to be the first IPA command after MPC initialization completes. So move the qeth_send_startlan() call from the layer disciplines into the core path, right after the MPC handshake. While at it, replace the magic LAN OFFLINE return code with the existing enum. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-12s390/qeth: shuffle MAC management functions aroundJulian Wiedmann
Move all MAC utility functions in one place, and drop the forward declarations. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-12s390/qeth: extract qeth_l2_remove_mac()Julian Wiedmann
This matches qeth_l2_write_mac(). Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-12s390/qeth: consolidate errno translationJulian Wiedmann
Consolidate errno handling for MAC management: Instead of doing this in every caller, do it in one place. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Suggested-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-12s390/qeth: don't convert return code twiceJulian Wiedmann
qeth_l2_send_groupmac() already translates the return code, so calling qeth_setdel_makerc() a second time only produces garbage. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-12s390/qeth: drop qeth_l2_del_all_macs() parameterJulian Wiedmann
The only caller passes del = 0, so remove both the parameter and the code that handles != 0. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-20s390/net: use net core MTU range checkingJarod Wilson
ctcm: - min_mtu = 576, max_mtu = 65527 netiucv: - min_mtu = 576, max_mtu = 65535 qeth: - min_mtu = 64, max_mtu = 65535 CC: netdev@vger.kernel.org CC: linux-s390@vger.kernel.org CC: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-16qeth: do not turn on SG per defaultUrsula Braun
According to recent performance measurements, turning on net_device feature NETIF_F_SG only behaves well, but turning on feature NETIF_F_GSO shows bad results. Since the kernel activates NETIF_F_GSO automatically as soon as the driver configures feature NETIF_F_SG, qeth should not activate feature NETIF_F_SG per default, until the qeth problems with NETIF_F_GSO are solved. Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-16qeth: do not limit number of gso segmentsUrsula Braun
To reduce the need of skb_linearize() calls, gso_max_segs of qeth net_devices had been limited according to the maximum number of qdio SBAL elements. But a gso segment cannot be larger than the mtu-size, while an SBAL element can contain up to 4096 bytes. The gso_max_segs limitation limits the maximum packet size given to the qeth driver. Performance measurements with tso-enabled qeth network interfaces and mtu-size 1500 showed, that the disadvantage of smaller packets is much more severe than the advantage of fewer skb_linearize() calls. This patch gets rid of the gso_max_segs limitations in the qeth driver. Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-16qeth: restore device features after recoveryHans Wippel
After device recovery, only a basic set of network device features is enabled on the device. If features like checksum offloading or TSO were enabled by the user before the recovery, this results in a mismatch between the network device features, that the kernel assumes to be enabled on the device, and the features actually enabled on the device. This patch tries to restore previously set features, that require changes on the device, after the recovery of a device. In case of an error, the network device's features are changed to contain only the features that are actually turned on. Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/ethernet/mellanox/mlx5/core/en.h drivers/net/ethernet/mellanox/mlx5/core/en_main.c drivers/net/usb/r8152.c All three conflicts were overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-04qeth: delete napi struct when removing a qeth deviceUrsula Braun
A qeth_card contains a napi_struct linked to the net_device during device probing. This struct must be deleted when removing the qeth device, otherwise Panic on oops can occur when qeth devices are repeatedly removed and added. Fixes: a1c3ed4c9ca ("qeth: NAPI support for l2 and l3 discipline") Cc: stable@vger.kernel.org # v2.6.37+ Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Tested-by: Alexander Klein <ALKL@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-16qeth: add network device features for VLAN devicesHans Wippel
Network device features indicate the capabilities of network devices (e.g., TX checksum offloading and TSO) and their configuration state. Additional network device features (vlan_features) indicate for each network device, which capabilities can be used on VLAN devices, that are configured on the respective base network device. In the current qeth implementation, network device features are only set for the base network devices and not for the VLAN devices. Thus, features like TX checksum offloading cannot be used on VLAN devices. This patch adds network device features to vlan_features, so they can be used by VLAN devices. Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-16qeth layer 2 and layer 3 common feature handlingThomas Richter
This patch introduces a common set of fix_features and set_features functions for layer 2 and layer 3. The RX, TX and TSO offload functionality on the OSA card is enabled using ethtool at user's request and not at device initialization as done before. For layer 3 the RX checksum offloading is disabled at device initialization time. Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-16qeth: optimize IP handling in rx_mode callbackLakhvich Dmitriy
In layer3 mode of the qeth driver, multicast IP addresses from struct net_device and other type of IP addresses from other sources require mapping to the OSA-card. This patch simplifies the IP address mapping logic, and changes imple- mentation of ndo_set_rx_mode callback and ip notifier events. Addresses are stored in private hashtables instead of lists now. It allows hardware registration/removal for new/deleted multicast addresses only. Signed-off-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Evgeny Cherkashin <Eugene.Crosser@ru.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-16qeth: introduce linearization fail count to statsEugene Crosser
When skb data touches too many pages, skb_linearize() is called opportunistically in the hope that less pages will be required for a big linear buffer than for multiple fragments. This patch intoduces a separate counter in ethtool statistics structure representing _failed_ linearization attempts. Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com> Reviewed-by: Thomas Richter <tmricht@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-06-16qeth: enable scatter/gather by defaultEugene Crosser
Set scatter/gather ON by default on OSA, for both layer 2 and layer 3 modes. We always use fragmentation over QDIO anyway, so let the upper layers of the stack take advantage of that. Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com> Reviewed-by: Thomas Richter <tmricht@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.0.4) at 2024-05-28 09:18:19 +0000