summaryrefslogtreecommitdiff
path: root/drivers/s390
AgeCommit message (Collapse)Author
2018-01-02s390/qeth: update takeover IPs after configuration changeJulian Wiedmann
[ Upstream commit 02f510f326501470348a5df341e8232c3497bbbb ] Any modification to the takeover IP-ranges requires that we re-evaluate which IP addresses are takeover-eligible. Otherwise we might do takeover for some addresses when we no longer should, or vice-versa. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-02s390/qeth: lock IP table while applying takeover changesJulian Wiedmann
[ Upstream commit 8a03a3692b100d84785ee7a834e9215e304c9e00 ] Modifying the flags of an IP addr object needs to be protected against eg. concurrent removal of the same object from the IP table. Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-02s390/qeth: don't apply takeover changes to RXIPJulian Wiedmann
[ Upstream commit b22d73d6689fd902a66c08ebe71ab2f3b351e22f ] When takeover is switched off, current code clears the 'TAKEOVER' flag on all IPs. But the flag is also used for RXIP addresses, and those should not be affected by the takeover mode. Fix the behaviour by consistenly applying takover logic to NORMAL addresses only. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-02s390/qeth: apply takeover changes when mode is toggledJulian Wiedmann
[ Upstream commit 7fbd9493f0eeae8cef58300505a9ef5c8fce6313 ] Just as for an explicit enable/disable, toggling the takeover mode also requires that the IP addresses get updated. Otherwise all IPs that were added to the table before the mode-toggle, get registered with the old settings. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-25s390/qeth: no ETH header for outbound AF_IUCVJulian Wiedmann
[ Upstream commit acd9776b5c45ef02d1a210969a6fcc058afb76e3 ] With AF_IUCV traffic, the skb passed to hard_start_xmit() has a 14 byte slot at skb->data, intended for an ETH header. qeth_l3_fill_af_iucv_hdr() fills this ETH header... and then immediately moves it to the skb's headroom, where it disappears and is never seen again. But it's still possible for us to return NETDEV_TX_BUSY after the skb has been modified. Since we didn't get a private copy of the skb, the next time the skb is delivered to hard_start_xmit() it no longer has the expected layout (we moved the ETH header to the headroom, so skb->data now starts at the IUCV_TRANS header). So when qeth_l3_fill_af_iucv_hdr() does another round of rebuilding, the resulting qeth header ends up all wrong. On transmission, the buffer is then rejected by the HiperSockets device with SBALF15 = x'04'. When this error is passed back to af_iucv as TX_NOTIFY_UNREACHABLE, it tears down the offending socket. As the ETH header for AF_IUCV serves no purpose, just align the code to what we do for IP traffic on L3 HiperSockets: keep the ETH header at skb->data, and pass down data_offset = ETH_HLEN to qeth_fill_buffer(). When mapping the payload into the SBAL elements, the ETH header is then stripped off. This avoids the skb manipulations in qeth_l3_fill_af_iucv_hdr(), and any buffer re-entering hard_start_xmit() after NETDEV_TX_BUSY is now processed properly. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-25s390/qeth: size calculation outbound buffersJulian Wiedmann
[ Upstream commit 7d969d2e8890f546c8cec634b3aa5f57d4eef883 ] Depending on the device type, hard_start_xmit() builds different output buffer formats. For instance with HiperSockets, on both L2 and L3 we strip the ETH header from the skb - L3 doesn't need it, and L2 carries it in the buffer's header element. For this, we pass data_offset = ETH_HLEN all the way down to __qeth_fill_buffer(), where skb->data is then adjusted accordingly. But the initial size calculation still considers the *full* skb length (including the ETH header). So qeth_get_elements_no() can erroneously reject a skb as too big, even though it would actually fit into an output buffer once the ETH header has been trimmed off later. Fix this by passing an additional offset to qeth_get_elements_no(), that indicates where in the skb the on-wire data actually begins. Since the current code uses data_offset=-1 for some special handling on OSA, we need to clamp data_offset to 0... On HiperSockets this helps when sending ~MTU-size skbs with weird page alignment. No change for OSA or AF_IUCV. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-16s390/qeth: fix thinko in IPv4 multicast address trackingJulian Wiedmann
[ Upsteam commit bc3ab70584696cb798b9e1e0ac8e6ced5fd4c3b8 ] Commit 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback") reworked how secondary addresses are managed for qeth devices. Instead of dropping & subsequently re-adding all addresses on every ndo_set_rx_mode() call, qeth now keeps track of the addresses that are currently registered with the HW. On a ndo_set_rx_mode(), we thus only need to do (de-)registration requests for the addresses that have actually changed. On L3 devices, the lookup for IPv4 Multicast addresses checks the wrong hashtable - and thus never finds a match. As a result, we first delete *all* such addresses, and then re-add them again. So each set_rx_mode() causes a short period where the IPv4 Multicast addresses are not registered, and the card stops forwarding inbound traffic for them. Fix this by setting the ->is_multicast flag on the lookup object, thus enabling qeth_l3_ip_from_hash() to search the correct hashtable and find a match there. Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-16s390/qeth: fix GSO throughput regressionJulian Wiedmann
[ Upstream commit 6d69b1f1eb7a2edf8a3547f361c61f2538e054bb ] Using GSO with small MTUs currently results in a substantial throughput regression - which is caused by how qeth needs to map non-linear skbs into its IO buffer elements: compared to a linear skb, each GSO-segmented skb effectively consumes twice as many buffer elements (ie two instead of one) due to the additional header-only part. This causes the Output Queue to be congested with low-utilized IO buffers. Fix this as follows: If the MSS is low enough so that a non-SG GSO segmentation produces order-0 skbs (currently ~3500 byte), opt out from NETIF_F_SG. This is where we anticipate the biggest savings, since an SG-enabled GSO segmentation produces skbs that always consume at least two buffer elements. Larger MSS values continue to get a SG-enabled GSO segmentation, since 1) the relative overhead of the additional header-only buffer element becomes less noticeable, and 2) the linearization overhead increases. With the throughput regression fixed, re-enable NETIF_F_SG by default to reap the significant CPU savings of GSO. Fixes: 5722963a8e83 ("qeth: do not turn on SG per default") Reported-by: Nils Hoppmann <niho@de.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-16s390/qeth: build max size GSO skbs on L2 devicesJulian Wiedmann
[ Upstream commit 0cbff6d4546613330a1c5f139f5c368e4ce33ca1 ] The current GSO skb size limit was copy&pasted over from the L3 path, where it is needed due to a TSO limitation. As L2 devices don't offer TSO support (and thus all GSO skbs are segmented before they reach the driver), there's no reason to restrict the stack in how large it may build the GSO skbs. Fixes: d52aec97e5bc ("qeth: enable scatter/gather in layer 2 mode") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-12-16s390/qeth: fix early exit from error pathJulian Wiedmann
[ Upstream commit 83cf79a2fec3cf499eb6cb9eb608656fc2a82776 ] When the allocation of the addr buffer fails, we need to free our refcount on the inetdevice before returning. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-15s390/qeth: issue STARTLAN as first IPA commandJulian Wiedmann
[ Upstream commit 1034051045d125579ab1e8fcd5a724eeb0e70149 ] STARTLAN needs to be the first IPA command after MPC initialization completes. So move the qeth_send_startlan() call from the layer disciplines into the core path, right after the MPC handshake. While at it, replace the magic LAN OFFLINE return code with the existing enum. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-15s390/qeth: fix retrieval of vipa and proxy-arp addressesUrsula Braun
[ Upstream commit e48b9eaaa29a0a7d5da2df136b07eefa0180d584 ] qeth devices in layer3 mode need a separate handling of vipa and proxy-arp addresses. vipa and proxy-arp addresses processed by qeth can be read from userspace. Introduced with commit 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback") the retrieval of vipa and proxy-arp addresses is broken, if more than one vipa or proxy-arp address are set. The qeth code used local variable "int i" for 2 different purposes. This patch now spends 2 separate local variables of type "int". While touching these functions hash_for_each_safe() is converted to hash_for_each(), since there is no removal of hash entries. Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reference-ID: RQM 3524 Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-08s390/dasd: check for device error pointer within state change interruptsStefan Haberland
[ Upstream commit 2202134e48a3b50320aeb9e3dd1186833e9d7e66 ] Check if the device pointer is valid. Just a sanity check since we already are in the int handler of the device. Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02scsi: zfcp: fix erp_action use-before-initialize in REC action traceSteffen Maier
commit ab31fd0ce65ec93828b617123792c1bb7c6dcc42 upstream. v4.10 commit 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race with LUN recovery") extended accessing parent pointer fields of struct zfcp_erp_action for tracing. If an erp_action has never been enqueued before, these parent pointer fields are uninitialized and NULL. Examples are zfcp objects freshly added to the parent object's children list, before enqueueing their first recovery subsequently. In zfcp_erp_try_rport_unblock(), we iterate such list. Accessing erp_action fields can cause a NULL pointer dereference. Since the kernel can read from lowcore on s390, it does not immediately cause a kernel page fault. Instead it can cause hangs on trying to acquire the wrong erp_action->adapter->dbf->rec_lock in zfcp_dbf_rec_action_lvl() ^bogus^ while holding already other locks with IRQs disabled. Real life example from attaching lots of LUNs in parallel on many CPUs: crash> bt 17723 PID: 17723 TASK: ... CPU: 25 COMMAND: "zfcperp0.0.1800" LOWCORE INFO: -psw : 0x0404300180000000 0x000000000038e424 -function : _raw_spin_lock_wait_flags at 38e424 ... #0 [fdde8fc90] zfcp_dbf_rec_action_lvl at 3e0004e9862 [zfcp] #1 [fdde8fce8] zfcp_erp_try_rport_unblock at 3e0004dfddc [zfcp] #2 [fdde8fd38] zfcp_erp_strategy at 3e0004e0234 [zfcp] #3 [fdde8fda8] zfcp_erp_thread at 3e0004e0a12 [zfcp] #4 [fdde8fe60] kthread at 173550 #5 [fdde8feb8] kernel_thread_starter at 10add2 zfcp_adapter zfcp_port zfcp_unit <address>, 0x404040d600000000 scsi_device NULL, returning early! zfcp_scsi_dev.status = 0x40000000 0x40000000 ZFCP_STATUS_COMMON_RUNNING crash> zfcp_unit <address> struct zfcp_unit { erp_action = { adapter = 0x0, port = 0x0, unit = 0x0, }, } zfcp_erp_action is always fully embedded into its container object. Such container object is never moved in its object tree (only add or delete). Hence, erp_action parent pointers can never change. To fix the issue, initialize the erp_action parent pointers before adding the erp_action container to any list and thus before it becomes accessible from outside of its initializing function. In order to also close the time window between zfcp_erp_setup_act() memsetting the entire erp_action to zero and setting the parent pointers again, drop the memset and instead explicitly initialize individually all erp_action fields except for parent pointers. To be extra careful not to introduce any other unintended side effect, even keep zeroing the erp_action fields for list and timer. Also double-check with WARN_ON_ONCE that erp_action parent pointers never change, so we get to know when we would deviate from previous behavior. Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race with LUN recovery") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-27scsi: zfcp: trace high part of "new" 64 bit SCSI LUNSteffen Maier
commit 5d4a3d0a2ff23799b956e5962b886287614e7fad upstream. Complements debugging aspects of the otherwise functionally complete v3.17 commit 9cb78c16f5da ("scsi: use 64-bit LUNs"). While I don't have access to a target exporting 3 or 4 level LUNs, I did test it by explicitly attaching a non-existent fake 4 level LUN by means of zfcp sysfs attribute "unit_add". In order to see corresponding trace records of otherwise successful events, we had to increase the trace level of area SCSI and HBA to 6. $ echo 6 > /sys/kernel/debug/s390dbf/zfcp_0.0.1880_scsi/level $ echo 6 > /sys/kernel/debug/s390dbf/zfcp_0.0.1880_hba/level $ echo 0x4011402240334044 > \ /sys/bus/ccw/drivers/zfcp/0.0.1880/0x50050763031bd327/unit_add Example output formatted by an updated zfcpdbf from the s390-tools package interspersed with kernel messages at scsi_logging_level=4605: Timestamp : ... Area : REC Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : scsla_1 LUN : 0x4011402240334044 WWPN : 0x50050763031bd327 D_ID : 0x00...... Adapter status : 0x5400050b Port status : 0x54000001 LUN status : 0x41000000 Ready count : 0x00000001 Running count : 0x00000000 ERP want : 0x01 ERP need : 0x01 scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY pass 1 length 36 scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY successful with code 0x0 Timestamp : ... Area : HBA Subarea : 00 Level : 6 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : fs_norm Request ID : 0x<inquiry2-req-id> Request status : 0x00000010 FSF cmnd : 0x00000001 FSF sequence no: 0x... FSF issued : ... FSF stat : 0x00000000 FSF stat qual : 00000000 00000000 00000000 00000000 Prot stat : 0x00000001 Prot stat qual : ........ ........ 00000000 00000000 Port handle : 0x... LUN handle : 0x... | Timestamp : ... Area : SCSI Subarea : 00 Level : 6 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : rsl_nor Request ID : 0x<inquiry2-req-id> SCSI ID : 0x00000000 SCSI LUN : 0x40224011 SCSI LUN high : 0x40444033 <======================= SCSI result : 0x00000000 SCSI retries : 0x00 SCSI allowed : 0x03 SCSI scribble : 0x<inquiry2-req-id> SCSI opcode : 12000000 a4000000 00000000 00000000 FCP rsp inf cod: 0x00 FCP rsp IU : 00000000 00000000 00000000 00000000 00000000 00000000 scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY pass 2 length 164 scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY successful with code 0x0 scsi 2:0:0:4630896905707208721: scsi scan: peripheral device type of 31, \ no device added Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: 9cb78c16f5da ("scsi: use 64-bit LUNs") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Reviewed-by: Jens Remus <jremus@linux.vnet.ibm.com> Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-27scsi: zfcp: trace HBA FSF response by default on dismiss or timedout late ↵Steffen Maier
response commit fdb7cee3b9e3c561502e58137a837341f10cbf8b upstream. At the default trace level, we only trace unsuccessful events including FSF responses. zfcp_dbf_hba_fsf_response() only used protocol status and FSF status to decide on an unsuccessful response. However, this is only one of multiple possible sources determining a failed struct zfcp_fsf_req. An FSF request can also "fail" if its response runs into an ERP timeout or if it gets dismissed because a higher level recovery was triggered [trace tags "erscf_1" or "erscf_2" in zfcp_erp_strategy_check_fsfreq()]. FSF requests with ERP timeout are: FSF_QTCB_EXCHANGE_CONFIG_DATA, FSF_QTCB_EXCHANGE_PORT_DATA, FSF_QTCB_OPEN_PORT_WITH_DID or FSF_QTCB_CLOSE_PORT or FSF_QTCB_CLOSE_PHYSICAL_PORT for target ports, FSF_QTCB_OPEN_LUN, FSF_QTCB_CLOSE_LUN. One example is slow queue processing which can cause follow-on errors, e.g. FSF_PORT_ALREADY_OPEN after FSF_QTCB_OPEN_PORT_WITH_DID timed out. In order to see the root cause, we need to see late responses even if the channel presented them successfully with FSF_PROT_GOOD and FSF_GOOD. Example trace records formatted with zfcpdbf from the s390-tools package: Timestamp : ... Area : REC Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : ... Record ID : 1 Tag : fcegpf1 LUN : 0xffffffffffffffff WWPN : 0x<WWPN> D_ID : 0x00<D_ID> Adapter status : 0x5400050b Port status : 0x41200000 LUN status : 0x00000000 Ready count : 0x00000001 Running count : 0x... ERP want : 0x02 ZFCP_ERP_ACTION_REOPEN_PORT ERP need : 0x02 ZFCP_ERP_ACTION_REOPEN_PORT | Timestamp : ... 30 seconds later Area : REC Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : ... Record ID : 2 Tag : erscf_2 LUN : 0xffffffffffffffff WWPN : 0x<WWPN> D_ID : 0x00<D_ID> Adapter status : 0x5400050b Port status : 0x41200000 LUN status : 0x00000000 Request ID : 0x<request_ID> ERP status : 0x10000000 ZFCP_STATUS_ERP_TIMEDOUT ERP step : 0x0800 ZFCP_ERP_STEP_PORT_OPENING ERP action : 0x02 ZFCP_ERP_ACTION_REOPEN_PORT ERP count : 0x00 | Timestamp : ... later than previous record Area : HBA Subarea : 00 Level : 5 > default level => 3 <= default level Exception : - CPU ID : 00 Caller : ... Record ID : 1 Tag : fs_qtcb => fs_rerr Request ID : 0x<request_ID> Request status : 0x00001010 ZFCP_STATUS_FSFREQ_DISMISSED | ZFCP_STATUS_FSFREQ_CLEANUP FSF cmnd : 0x00000005 FSF sequence no: 0x... FSF issued : ... > 30 seconds ago FSF stat : 0x00000000 FSF_GOOD FSF stat qual : 00000000 00000000 00000000 00000000 Prot stat : 0x00000001 FSF_PROT_GOOD Prot stat qual : 00000000 00000000 00000000 00000000 Port handle : 0x... LUN handle : 0x00000000 QTCB log length: ... QTCB log info : ... In case of problems detecting that new responses are waiting on the input queue, we sooner or later trigger adapter recovery due to an FSF request timeout (trace tag "fsrth_1"). FSF requests with FSF request timeout are: typically FSF_QTCB_ABORT_FCP_CMND; but theoretically also FSF_QTCB_EXCHANGE_CONFIG_DATA or FSF_QTCB_EXCHANGE_PORT_DATA via sysfs, FSF_QTCB_OPEN_PORT_WITH_DID or FSF_QTCB_CLOSE_PORT for WKA ports, FSF_QTCB_FCP_CMND for task management function (LUN / target reset). One or more pending requests can meanwhile have FSF_PROT_GOOD and FSF_GOOD because the channel filled in the response via DMA into the request's QTCB. In a theroretical case, inject code can create an erroneous FSF request on purpose. If data router is enabled, it uses deferred error reporting. A READ SCSI command can succeed with FSF_PROT_GOOD, FSF_GOOD, and SAM_STAT_GOOD. But on writing the read data to host memory via DMA, it can still fail, e.g. if an intentionally wrong scatter list does not provide enough space. Rather than getting an unsuccessful response, we get a QDIO activate check which in turn triggers adapter recovery. One or more pending requests can meanwhile have FSF_PROT_GOOD and FSF_GOOD because the channel filled in the response via DMA into the request's QTCB. Example trace records formatted with zfcpdbf from the s390-tools package: Timestamp : ... Area : HBA Subarea : 00 Level : 6 > default level => 3 <= default level Exception : - CPU ID : .. Caller : ... Record ID : 1 Tag : fs_norm => fs_rerr Request ID : 0x<request_ID2> Request status : 0x00001010 ZFCP_STATUS_FSFREQ_DISMISSED | ZFCP_STATUS_FSFREQ_CLEANUP FSF cmnd : 0x00000001 FSF sequence no: 0x... FSF issued : ... FSF stat : 0x00000000 FSF_GOOD FSF stat qual : 00000000 00000000 00000000 00000000 Prot stat : 0x00000001 FSF_PROT_GOOD Prot stat qual : ........ ........ 00000000 00000000 Port handle : 0x... LUN handle : 0x... | Timestamp : ... Area : SCSI Subarea : 00 Level : 3 Exception : - CPU ID : .. Caller : ... Record ID : 1 Tag : rsl_err Request ID : 0x<request_ID2> SCSI ID : 0x... SCSI LUN : 0x... SCSI result : 0x000e0000 DID_TRANSPORT_DISRUPTED SCSI retries : 0x00 SCSI allowed : 0x05 SCSI scribble : 0x<request_ID2> SCSI opcode : 28... Read(10) FCP rsp inf cod: 0x00 FCP rsp IU : 00000000 00000000 00000000 00000000 ^^ SAM_STAT_GOOD 00000000 00000000 Only with luck in both above cases, we could see a follow-on trace record of an unsuccesful event following a successful but late FSF response with FSF_PROT_GOOD and FSF_GOOD. Typically this was the case for I/O requests resulting in a SCSI trace record "rsl_err" with DID_TRANSPORT_DISRUPTED [On ZFCP_STATUS_FSFREQ_DISMISSED, zfcp_fsf_protstatus_eval() sets ZFCP_STATUS_FSFREQ_ERROR seen by the request handler functions as failure]. However, the reason for this follow-on trace was invisible because the corresponding HBA trace record was missing at the default trace level (by default hidden records with tags "fs_norm", "fs_qtcb", or "fs_open"). On adapter recovery, after we had shut down the QDIO queues, we perform unsuccessful pseudo completions with flag ZFCP_STATUS_FSFREQ_DISMISSED for each pending FSF request in zfcp_fsf_req_dismiss_all(). In order to find the root cause, we need to see all pseudo responses even if the channel presented them successfully with FSF_PROT_GOOD and FSF_GOOD. Therefore, check zfcp_fsf_req.status for ZFCP_STATUS_FSFREQ_DISMISSED or ZFCP_STATUS_FSFREQ_ERROR and trace with a new tag "fs_rerr". It does not matter that there are numerous places which set ZFCP_STATUS_FSFREQ_ERROR after the location where we trace an FSF response early. These cases are based on protocol status != FSF_PROT_GOOD or == FSF_PROT_FSF_STATUS_PRESENTED and are thus already traced by default as trace tag "fs_perr" or "fs_ferr" respectively. NB: The trace record with tag "fssrh_1" for status read buffers on dismiss all remains. zfcp_fsf_req_complete() handles this and returns early. All other FSF request types are handled separately and as described above. Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: 8a36e4532ea1 ("[SCSI] zfcp: enhancement of zfcp debug features") Fixes: 2e261af84cdb ("[SCSI] zfcp: Only collect FSF/HBA debug data for matching trace levels") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-27scsi: zfcp: fix payload with full FCP_RSP IU in SCSI trace recordsSteffen Maier
commit 12c3e5754c8022a4f2fd1e9f00d19e99ee0d3cc1 upstream. If the FCP_RSP UI has optional parts (FCP_SNS_INFO or FCP_RSP_INFO) and thus does not fit into the fsp_rsp field built into a SCSI trace record, trace the full FCP_RSP UI with all optional parts as payload record instead of just FCP_SNS_INFO as payload and a 1 byte RSP_INFO_CODE part of FCP_RSP_INFO built into the SCSI record. That way we would also get the full FCP_SNS_INFO in case a target would ever send more than min(SCSI_SENSE_BUFFERSIZE==96, ZFCP_DBF_PAY_MAX_REC==256)==96. The mandatory part of FCP_RSP IU is only 24 bytes. PAYload costs at least one full PAY record of 256 bytes anyway. We cap to the hardware response size which is only FSF_FCP_RSP_SIZE==128. So we can just put the whole FCP_RSP IU with any optional parts into PAYload similarly as we do for SAN PAY since v4.9 commit aceeffbb59bb ("zfcp: trace full payload of all SAN records (req,resp,iels)"). This does not cause any additional trace records wasting memory. Decoded trace records were confusing because they showed a hard-coded sense data length of 96 even if the FCP_RSP_IU field FCP_SNS_LEN showed actually less. Since the same commit, we set pl_len for SAN traces to the full length of a request/response even if we cap the corresponding trace. In contrast, here for SCSI traces we set pl_len to the pre-computed length of FCP_RSP IU considering SNS_LEN or RSP_LEN if valid. Nonetheless we trace a hardcoded payload of length FSF_FCP_RSP_SIZE==128 if there were optional parts. This makes it easier for the zfcpdbf tool to format only the relevant part of the long FCP_RSP UI buffer. And any trailing information is still available in the payload trace record just in case. Rename the payload record tag from "fcp_sns" to "fcp_riu" to make the new content explicit to zfcpdbf which can then pick a suitable field name such as "FCP rsp IU all:" instead of "Sense info :" Also, the same zfcpdbf can still be backwards compatible with "fcp_sns". Old example trace record before this fix, formatted with the tool zfcpdbf from s390-tools: Timestamp : ... Area : SCSI Subarea : 00 Level : 3 Exception : - CPU id : .. Caller : 0x... Record id : 1 Tag : rsl_err Request id : 0x<request_id> SCSI ID : 0x... SCSI LUN : 0x... SCSI result : 0x00000002 SCSI retries : 0x00 SCSI allowed : 0x05 SCSI scribble : 0x<request_id> SCSI opcode : 00000000 00000000 00000000 00000000 FCP rsp inf cod: 0x00 FCP rsp IU : 00000000 00000000 00000202 00000000 ^^==FCP_SNS_LEN_VALID 00000020 00000000 ^^^^^^^^==FCP_SNS_LEN==32 Sense len : 96 <==min(SCSI_SENSE_BUFFERSIZE,ZFCP_DBF_PAY_MAX_REC) Sense info : 70000600 00000018 00000000 29000000 00000400 00000000 00000000 00000000 00000000 00000000 00000000 00000000<==superfluous 00000000 00000000 00000000 00000000<==superfluous 00000000 00000000 00000000 00000000<==superfluous 00000000 00000000 00000000 00000000<==superfluous New example trace records with this fix: Timestamp : ... Area : SCSI Subarea : 00 Level : 3 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : rsl_err Request ID : 0x<request_id> SCSI ID : 0x... SCSI LUN : 0x... SCSI result : 0x00000002 SCSI retries : 0x00 SCSI allowed : 0x03 SCSI scribble : 0x<request_id> SCSI opcode : a30c0112 00000000 02000000 00000000 FCP rsp inf cod: 0x00 FCP rsp IU : 00000000 00000000 00000a02 00000200 00000020 00000000 FCP rsp IU len : 56 FCP rsp IU all : 00000000 00000000 00000a02 00000200 ^^=FCP_RESID_UNDER|FCP_SNS_LEN_VALID 00000020 00000000 70000500 00000018 ^^^^^^^^==FCP_SNS_LEN ^^^^^^^^^^^^^^^^^ 00000000 240000cb 00011100 00000000 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 00000000 00000000 ^^^^^^^^^^^^^^^^^==FCP_SNS_INFO Timestamp : ... Area : SCSI Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : lr_okay Request ID : 0x<request_id> SCSI ID : 0x... SCSI LUN : 0x... SCSI result : 0x00000000 SCSI retries : 0x00 SCSI allowed : 0x05 SCSI scribble : 0x<request_id> SCSI opcode : <CDB of unrelated SCSI command passed to eh handler> FCP rsp inf cod: 0x00 FCP rsp IU : 00000000 00000000 00000100 00000000 00000000 00000008 FCP rsp IU len : 32 FCP rsp IU all : 00000000 00000000 00000100 00000000 ^^==FCP_RSP_LEN_VALID 00000000 00000008 00000000 00000000 ^^^^^^^^==FCP_RSP_LEN ^^^^^^^^^^^^^^^^^==FCP_RSP_INFO Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: 250a1352b95e ("[SCSI] zfcp: Redesign of the debug tracing for SCSI records.") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-27scsi: zfcp: fix missing trace records for early returns in TMF eh handlersSteffen Maier
commit 1a5d999ebfc7bfe28deb48931bb57faa8e4102b6 upstream. For problem determination we need to see that we were in scsi_eh as well as whether and why we were successful or not. The following commits introduced new early returns without adding a trace record: v2.6.35 commit a1dbfddd02d2 ("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh") on fc_block_scsi_eh() returning != 0 which is FAST_IO_FAIL, v2.6.30 commit 63caf367e1c9 ("[SCSI] zfcp: Improve reliability of SCSI eh handlers in zfcp") on not having gotten an FSF request after the maximum number of retry attempts and thus could not issue a TMF and has to return FAILED. Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: a1dbfddd02d2 ("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh") Fixes: 63caf367e1c9 ("[SCSI] zfcp: Improve reliability of SCSI eh handlers in zfcp") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-27scsi: zfcp: fix passing fsf_req to SCSI trace on TMF to correlate with HBASteffen Maier
commit 9fe5d2b2fd30aa8c7827ec62cbbe6d30df4fe3e3 upstream. Without this fix we get SCSI trace records on task management functions which cannot be correlated to HBA trace records because all fields related to the FSF request are empty (zero). Also, the FCP_RSP_IU is missing as well as any sense data if available. This was caused by v2.6.14 commit 8a36e4532ea1 ("[SCSI] zfcp: enhancement of zfcp debug features") introducing trace records for TMFs but hard coding NULL for a possibly existing TMF FSF request. The scsi_cmnd scribble is also zero or unrelated for the TMF request so it also could not lookup a suitable FSF request from there. A broken example trace record formatted with zfcpdbf from the s390-tools package: Timestamp : ... Area : SCSI Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : lr_fail Request ID : 0x0000000000000000 ^^^^^^^^^^^^^^^^ no correlation to HBA record SCSI ID : 0x<scsitarget> SCSI LUN : 0x<scsilun> SCSI result : 0x000e0000 SCSI retries : 0x00 SCSI allowed : 0x05 SCSI scribble : 0x0000000000000000 SCSI opcode : 2a000017 3bb80000 08000000 00000000 FCP rsp inf cod: 0x00 ^^ no TMF response FCP rsp IU : 00000000 00000000 00000000 00000000 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 00000000 00000000 ^^^^^^^^^^^^^^^^^ no interesting FCP_RSP_IU Sense len : ... ^^^^^^^^^^^^^^^^^^^^ no sense data length Sense info : ... ^^^^^^^^^^^^^^^^^^^^ no sense data content, even if present There are some true cases where we really do not have an FSF request: "rsl_fai" from zfcp_dbf_scsi_fail_send() called for early returns / completions in zfcp_scsi_queuecommand(), "abrt_or", "abrt_bl", "abrt_ru", "abrt_ar" from zfcp_scsi_eh_abort_handler() where we did not get as far, "lr_nres", "tr_nres" from zfcp_task_mgmt_function() where we're successful and do not need to do anything because adapter stopped. For these cases it's correct to pass NULL for fsf_req to _zfcp_dbf_scsi(). Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: 8a36e4532ea1 ("[SCSI] zfcp: enhancement of zfcp debug features") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-27scsi: zfcp: fix capping of unsuccessful GPN_FT SAN response trace recordsSteffen Maier
commit 975171b4461be296a35e83ebd748946b81cf0635 upstream. v4.9 commit aceeffbb59bb ("zfcp: trace full payload of all SAN records (req,resp,iels)") fixed trace data loss of 2.6.38 commit 2c55b750a884 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.") necessary for problem determination, e.g. to see the currently active zone set during automatic port scan. While it already saves space by not dumping any empty residual entries of the large successful GPN_FT response (4 pages), there are seldom cases where the GPN_FT response is unsuccessful and likely does not have FC_NS_FID_LAST set in fp_flags so we did not cap the trace record. We typically see such case for an initiator WWPN, which is not in any zone. Cap unsuccessful responses to at least the actual basic CT_IU response plus whatever fits the SAN trace record built-in "payload" buffer just in case there's trailing information of which we would at least see the existence and its beginning. In order not to erroneously cap successful responses, we need to swap calling the trace function and setting the CT / ELS status to success (0). Example trace record pair formatted with zfcpdbf: Timestamp : ... Area : SAN Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : fssct_1 Request ID : 0x<request_id> Destination ID : 0x00fffffc SAN req short : 01000000 fc020000 01720ffc 00000000 00000008 SAN req length : 20 | Timestamp : ... Area : SAN Subarea : 00 Level : 1 Exception : - CPU ID : .. Caller : 0x... Record ID : 2 Tag : fsscth2 Request ID : 0x<request_id> Destination ID : 0x00fffffc SAN resp short : 01000000 fc020000 80010000 00090700 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] SAN resp length: 16384 San resp info : 01000000 fc020000 80010000 00090700 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] 00000000 00000000 00000000 00000000 [trailing info] The fix saves all but one of the previously associated 64 PAYload trace record chunks of size 256 bytes each. Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: aceeffbb59bb ("zfcp: trace full payload of all SAN records (req,resp,iels)") Fixes: 2c55b750a884 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-27scsi: zfcp: add handling for FCP_RESID_OVER to the fcp ingress pathBenjamin Block
commit a099b7b1fc1f0418ab8d79ecf98153e1e134656e upstream. Up until now zfcp would just ignore the FCP_RESID_OVER flag in the FCP response IU. When this flag is set, it is possible, in regards to the FCP standard, that the storage-server processes the command normally, up to the point where data is missing and simply ignores those. In this case no CHECK CONDITION would be set, and because we ignored the FCP_RESID_OVER flag we resulted in at least a data loss or even -corruption as a follow-up error, depending on how the applications/layers on top behave. To prevent this, we now set the host-byte of the corresponding scsi_cmnd to DID_ERROR. Other storage-behaviors, where the same condition results in a CHECK CONDITION set in the answer, don't need to be changed as they are handled in the mid-layer already. Following is an example trace record decoded with zfcpdbf from the s390-tools package. We forcefully injected a fc_dl which is one byte too small: Timestamp : ... Area : SCSI Subarea : 00 Level : 3 Exception : - CPU ID : .. Caller : 0x... Record ID : 1 Tag : rsl_err Request ID : 0x... SCSI ID : 0x... SCSI LUN : 0x... SCSI result : 0x00070000 ^^DID_ERROR SCSI retries : 0x.. SCSI allowed : 0x.. SCSI scribble : 0x... SCSI opcode : 2a000000 00000000 08000000 00000000 FCP rsp inf cod: 0x00 FCP rsp IU : 00000000 00000000 00000400 00000001 ^^fr_flags==FCP_RESID_OVER ^^fr_status==SAM_STAT_GOOD ^^^^^^^^fr_resid 00000000 00000000 As of now, we don't actively handle to possibility that a response IU has both flags - FCP_RESID_OVER and FCP_RESID_UNDER - set at once. Reported-by: Luke M. Hopkins <lmhopkin@us.ibm.com> Reviewed-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: 553448f6c483 ("[SCSI] zfcp: Message cleanup") Fixes: ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.") (tglx/history.git) Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-27scsi: zfcp: fix queuecommand for scsi_eh commands when DIX enabledSteffen Maier
commit 71b8e45da51a7b64a23378221c0a5868bd79da4f upstream. Since commit db007fc5e20c ("[SCSI] Command protection operation"), scsi_eh_prep_cmnd() saves scmd->prot_op and temporarily resets it to SCSI_PROT_NORMAL. Other FCP LLDDs such as qla2xxx and lpfc shield their queuecommand() to only access any of scsi_prot_sg...() if (scsi_get_prot_op(cmd) != SCSI_PROT_NORMAL). Do the same thing for zfcp, which introduced DIX support with commit ef3eb71d8ba4 ("[SCSI] zfcp: Introduce experimental support for DIF/DIX"). Otherwise, TUR SCSI commands as part of scsi_eh likely fail in zfcp, because the regular SCSI command with DIX protection data, that scsi_eh re-uses in scsi_send_eh_cmnd(), of course still has (scsi_prot_sg_count() != 0) and so zfcp sends down bogus requests to the FCP channel hardware. This causes scsi_eh_test_devices() to have (finish_cmds == 0) [not SCSI device is online or not scsi_eh_tur() failed] so regular SCSI commands, that caused / were affected by scsi_eh, are moved to work_q and scsi_eh_test_devices() itself returns false. In turn, it unnecessarily escalates in our case in scsi_eh_ready_devs() beyond host reset to finally scsi_eh_offline_sdevs() which sets affected SCSI devices offline with the following kernel message: "kernel: sd H:0:T:L: Device offlined - not ready after error recovery" Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: ef3eb71d8ba4 ("[SCSI] zfcp: Introduce experimental support for DIF/DIX") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-07s390/qeth: add missing hash table initializationsUrsula Braun
[ Upstream commit ebccc7397e4a49ff64c8f44a54895de9d32fe742 ] commit 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback") added new hash tables, but missed to initialize them. Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback") Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-07s390/qeth: avoid null pointer dereference on OSNJulian Wiedmann
[ Upstream commit 25e2c341e7818a394da9abc403716278ee646014 ] Access card->dev only after checking whether's its valid. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-07s390/qeth: unbreak OSM and OSN supportJulian Wiedmann
[ Upstream commit 2d2ebb3ed0c6acfb014f98e427298673a5d07b82 ] commit b4d72c08b358 ("qeth: bridgeport support - basic control") broke the support for OSM and OSN devices as follows: As OSM and OSN are L2 only, qeth_core_probe_device() does an early setup by loading the l2 discipline and calling qeth_l2_probe_device(). In this context, adding the l2-specific bridgeport sysfs attributes via qeth_l2_create_device_attributes() hits a BUG_ON in fs/sysfs/group.c, since the basic sysfs infrastructure for the device hasn't been established yet. Note that OSN actually has its own unique sysfs attributes (qeth_osn_devtype), so the additional attributes shouldn't be created at all. For OSM, add a new qeth_l2_devtype that contains all the common and l2-specific sysfs attributes. When qeth_core_probe_device() does early setup for OSM or OSN, assign the corresponding devtype so that the ccwgroup probe code creates the full set of sysfs attributes. This allows us to skip qeth_l2_create_device_attributes() in case of an early setup. Any device that can't do early setup will initially have only the generic sysfs attributes, and when it's probed later qeth_l2_probe_device() adds the l2-specific attributes. If an early-setup device is removed (by calling ccwgroup_ungroup()), device_unregister() will - using the devtype - delete the l2-specific attributes before qeth_l2_remove_device() is called. So make sure to not remove them twice. What complicates the issue is that qeth_l2_probe_device() and qeth_l2_remove_device() is also called on a device when its layer2 attribute changes (ie. its layer mode is switched). For early-setup devices this wouldn't work properly - we wouldn't remove the l2-specific attributes when switching to L3. But switching the layer mode doesn't actually make any sense; we already decided that the device can only operate in L2! So just refuse to switch the layer mode on such devices. Note that OSN doesn't have a layer2 attribute, so we only need to special-case OSM. Based on an initial patch by Ursula Braun. Fixes: b4d72c08b358 ("qeth: bridgeport support - basic control") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-07s390/qeth: handle sysfs error during initializationUrsula Braun
[ Upstream commit 9111e7880ccf419548c7b0887df020b08eadb075 ] When setting up the device from within the layer discipline's probe routine, creating the layer-specific sysfs attributes can fail. Report this error back to the caller, and handle it by releasing the layer discipline. Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> [jwi: updated commit msg, moved an OSN change to a subsequent patch] Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-22s390/zcrypt: Introduce CEX6 tolerationHarald Freudenberger
[ Upstream commit b3e8652bcbfa04807e44708d4d0c8cdad39c9215 ] Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-15s390/chsc: Add exception handler for CHSC instructionPeter Oberparleiter
commit 77759137248f34864a8f7a58bbcebfcf1047504a upstream. Prevent kernel crashes due to unhandled exceptions raised by the CHSC instruction which may for example be triggered by invalid ioctl data. Fixes: 64150adf89df ("s390/cio: Introduce generic synchronous CHSC IOCTL") Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-15s390/dcssblk: fix device size calculation in dcssblk_direct_access()Gerald Schaefer
commit a63f53e34db8b49675448d03ae324f6c5bc04fe6 upstream. Since commit dd22f551 "block: Change direct_access calling convention", the device size calculation in dcssblk_direct_access() is off-by-one. This results in bdev_direct_access() always returning -ENXIO because the returned value is not page aligned. Fix this by adding 1 to the dev_sz calculation. Fixes: dd22f551 ("block: Change direct_access calling convention") Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-15s390/qdio: clear DSCI prior to scanning multiple input queuesJulian Wiedmann
commit 1e4a382fdc0ba8d1a85b758c0811de3a3631085e upstream. For devices with multiple input queues, tiqdio_call_inq_handlers() iterates over all input queues and clears the device's DSCI during each iteration. If the DSCI is re-armed during one of the later iterations, we therefore do not scan the previous queues again. The re-arming also raises a new adapter interrupt. But its handler does not trigger a rescan for the device, as the DSCI has already been erroneously cleared. This can result in queue stalls on devices with multiple input queues. Fix it by clearing the DSCI just once, prior to scanning the queues. As the code is moved in front of the loop, we also need to access the DSCI directly (ie irq->dsci) instead of going via each queue's parent pointer to the same irq. This is not a functional change, and a follow-up patch will clean up the other users. In practice, this bug only affects CQ-enabled HiperSockets devices, ie. devices with sysfs-attribute "hsuid" set. Setting a hsuid is needed for AF_IUCV socket applications that use HiperSockets communication. Fixes: 104ea556ee7f ("qdio: support asynchronous delivery of storage blocks") Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-14scsi: zfcp: fix use-after-free by not tracing WKA port open/close on failed sendSteffen Maier
commit 2dfa6688aafdc3f74efeb1cf05fb871465d67f79 upstream. Dan Carpenter kindly reported: <quote> The patch d27a7cb91960: "zfcp: trace on request for open and close of WKA port" from Aug 10, 2016, leads to the following static checker warning: drivers/s390/scsi/zfcp_fsf.c:1615 zfcp_fsf_open_wka_port() warn: 'req' was already freed. drivers/s390/scsi/zfcp_fsf.c 1609 zfcp_fsf_start_timer(req, ZFCP_FSF_REQUEST_TIMEOUT); 1610 retval = zfcp_fsf_req_send(req); 1611 if (retval) 1612 zfcp_fsf_req_free(req); ^^^ Freed. 1613 out: 1614 spin_unlock_irq(&qdio->req_q_lock); 1615 if (req && !IS_ERR(req)) 1616 zfcp_dbf_rec_run_wka("fsowp_1", wka_port, req->req_id); ^^^^^^^^^^^ Use after free. 1617 return retval; 1618 } Same thing for zfcp_fsf_close_wka_port() as well. </quote> Rather than relying on req being NULL (or ERR_PTR) for all cases where we don't want to trace or should not trace, simply check retval which is unconditionally initialized with -EIO != 0 and it can only become 0 on successful retval = zfcp_fsf_req_send(req). With that we can also remove the then again unnecessary unconditional initialization of req which was introduced with that earlier commit. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Suggested-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: d27a7cb91960 ("zfcp: trace on request for open and close of WKA port") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Reviewed-by: Jens Remus <jremus@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-09s390/vmlogrdr: fix IUCV buffer allocationGerald Schaefer
commit 5457e03de918f7a3e294eb9d26a608ab8a579976 upstream. The buffer for iucv_message_receive() needs to be below 2 GB. In __iucv_message_receive(), the buffer address is casted to an u32, which would result in either memory corruption or an addressing exception when using addresses >= 2 GB. Fix this by using GFP_DMA for the buffer allocation. Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-09scsi: zfcp: fix rport unblock race with LUN recoverySteffen Maier
commit 6f2ce1c6af37191640ee3ff6e8fc39ea10352f4c upstream. It is unavoidable that zfcp_scsi_queuecommand() has to finish requests with DID_IMM_RETRY (like fc_remote_port_chkready()) during the time window when zfcp detected an unavailable rport but fc_remote_port_delete(), which is asynchronous via zfcp_scsi_schedule_rport_block(), has not yet blocked the rport. However, for the case when the rport becomes available again, we should prevent unblocking the rport too early. In contrast to other FCP LLDDs, zfcp has to open each LUN with the FCP channel hardware before it can send I/O to a LUN. So if a port already has LUNs attached and we unblock the rport just after port recovery, recoveries of LUNs behind this port can still be pending which in turn force zfcp_scsi_queuecommand() to unnecessarily finish requests with DID_IMM_RETRY. This also opens a time window with unblocked rport (until the followup LUN reopen recovery has finished). If a scsi_cmnd timeout occurs during this time window fc_timed_out() cannot work as desired and such command would indeed time out and trigger scsi_eh. This prevents a clean and timely path failover. This should not happen if the path issue can be recovered on FC transport layer such as path issues involving RSCNs. Fix this by only calling zfcp_scsi_schedule_rport_register(), to asynchronously trigger fc_remote_port_add(), after all LUN recoveries as children of the rport have finished and no new recoveries of equal or higher order were triggered meanwhile. Finished intentionally includes any recovery result no matter if successful or failed (still unblock rport so other successful LUNs work). For simplicity, we check after each finished LUN recovery if there is another LUN recovery pending on the same port and then do nothing. We handle the special case of a successful recovery of a port without LUN children the same way without changing this case's semantics. For debugging we introduce 2 new trace records written if the rport unblock attempt was aborted due to still unfinished or freshly triggered recovery. The records are only written above the default trace level. Benjamin noticed the important special case of new recovery that can be triggered between having given up the erp_lock and before calling zfcp_erp_action_cleanup() within zfcp_erp_strategy(). We must avoid the following sequence: ERP thread rport_work other context ------------------------- -------------- -------------------------------- port is unblocked, rport still blocked, due to pending/running ERP action, so ((port->status & ...UNBLOCK) != 0) and (port->rport == NULL) unlock ERP zfcp_erp_action_cleanup() case ZFCP_ERP_ACTION_REOPEN_LUN: zfcp_erp_try_rport_unblock() ((status & ...UNBLOCK) != 0) [OLD!] zfcp_erp_port_reopen() lock ERP zfcp_erp_port_block() port->status clear ...UNBLOCK unlock ERP zfcp_scsi_schedule_rport_block() port->rport_task = RPORT_DEL queue_work(rport_work) zfcp_scsi_rport_work() (port->rport_task != RPORT_ADD) port->rport_task = RPORT_NONE zfcp_scsi_rport_block() if (!port->rport) return zfcp_scsi_schedule_rport_register() port->rport_task = RPORT_ADD queue_work(rport_work) zfcp_scsi_rport_work() (port->rport_task == RPORT_ADD) port->rport_task = RPORT_NONE zfcp_scsi_rport_register() (port->rport == NULL) rport = fc_remote_port_add() port->rport = rport; Now the rport was erroneously unblocked while the zfcp_port is blocked. This is another situation we want to avoid due to scsi_eh potential. This state would at least remain until the new recovery from the other context finished successfully, or potentially forever if it failed. In order to close this race, we take the erp_lock inside zfcp_erp_try_rport_unblock() when checking the status of zfcp_port or LUN. With that, the possible corresponding rport state sequences would be: (unblock[ERP thread],block[other context]) if the ERP thread gets erp_lock first and still sees ((port->status & ...UNBLOCK) != 0), (block[other context],NOP[ERP thread]) if the ERP thread gets erp_lock after the other context has already cleard ...UNBLOCK from port->status. Since checking fields of struct erp_action is unsafe because they could have been overwritten (re-used for new recovery) meanwhile, we only check status of zfcp_port and LUN since these are only changed under erp_lock elsewhere. Regarding the check of the proper status flags (port or port_forced are similar to the shown adapter recovery): [zfcp_erp_adapter_shutdown()] zfcp_erp_adapter_reopen() zfcp_erp_adapter_block() * clear UNBLOCK ---------------------------------------+ zfcp_scsi_schedule_rports_block() | write_lock_irqsave(&adapter->erp_lock, flags);-------+ | zfcp_erp_action_enqueue() | | zfcp_erp_setup_act() | | * set ERP_INUSE -----------------------------------|--|--+ write_unlock_irqrestore(&adapter->erp_lock, flags);--+ | | .context-switch. | | zfcp_erp_thread() | | zfcp_erp_strategy() | | write_lock_irqsave(&adapter->erp_lock, flags);------+ | | ... | | | zfcp_erp_strategy_check_target() | | | zfcp_erp_strategy_check_adapter() | | | zfcp_erp_adapter_unblock() | | | * set UNBLOCK -----------------------------------|--+ | zfcp_erp_action_dequeue() | | * clear ERP_INUSE ---------------------------------|-----+ ... | write_unlock_irqrestore(&adapter->erp_lock, flags);-+ Hence, we should check for both UNBLOCK and ERP_INUSE because they are interleaved. Also we need to explicitly check ERP_FAILED for the link down case which currently does not clear the UNBLOCK flag in zfcp_fsf_link_down_info_eval(). Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: 8830271c4819 ("[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport") Fixes: a2fa0aede07c ("[SCSI] zfcp: Block FC transport rports early on errors") Fixes: 5f852be9e11d ("[SCSI] zfcp: Fix deadlock between zfcp ERP and SCSI") Fixes: 338151e06608 ("[SCSI] zfcp: make use of fc_remote_port_delete when target port is unavailable") Fixes: 3859f6a248cb ("[PATCH] zfcp: add rports to enable scsi_add_device to work again") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-09scsi: zfcp: do not trace pure benign residual HBA responses at default levelSteffen Maier
commit 56d23ed7adf3974f10e91b643bd230e9c65b5f79 upstream. Since quite a while, Linux issues enough SCSI commands per scsi_device which successfully return with FCP_RESID_UNDER, FSF_FCP_RSP_AVAILABLE, and SAM_STAT_GOOD. This floods the HBA trace area and we cannot see other and important HBA trace records long enough. Therefore, do not trace HBA response errors for pure benign residual under counts at the default trace level. This excludes benign residual under count combined with other validity bits set in FCP_RSP_IU, such as FCP_SNS_LEN_VAL. For all those other cases, we still do want to see both the HBA record and the corresponding SCSI record by default. Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: a54ca0f62f95 ("[SCSI] zfcp: Redesign of the debug tracing for HBA records.") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-09scsi: zfcp: fix use-after-"free" in FC ingress path after TMFBenjamin Block
commit dac37e15b7d511e026a9313c8c46794c144103cd upstream. When SCSI EH invokes zFCP's callbacks for eh_device_reset_handler() and eh_target_reset_handler(), it expects us to relent the ownership over the given scsi_cmnd and all other scsi_cmnds within the same scope - LUN or target - when returning with SUCCESS from the callback ('release' them). SCSI EH can then reuse those commands. We did not follow this rule to release commands upon SUCCESS; and if later a reply arrived for one of those supposed to be released commands, we would still make use of the scsi_cmnd in our ingress tasklet. This will at least result in undefined behavior or a kernel panic because of a wrong kernel pointer dereference. To fix this, we NULLify all pointers to scsi_cmnds (struct zfcp_fsf_req *)->data in the matching scope if a TMF was successful. This is done under the locks (struct zfcp_adapter *)->abort_lock and (struct zfcp_reqlist *)->lock to prevent the requests from being removed from the request-hashtable, and the ingress tasklet from making use of the scsi_cmnd-pointer in zfcp_fsf_fcp_cmnd_handler(). For cases where a reply arrives during SCSI EH, but before we get a chance to NULLify the pointer - but before we return from the callback -, we assume that the code is protected from races via the CAS operation in blk_complete_request() that is called in scsi_done(). The following stacktrace shows an example for a crash resulting from the previous behavior: Unable to handle kernel pointer dereference at virtual kernel address fffffee17a672000 Oops: 0038 [#1] SMP CPU: 2 PID: 0 Comm: swapper/2 Not tainted task: 00000003f7ff5be0 ti: 00000003f3d38000 task.ti: 00000003f3d38000 Krnl PSW : 0404d00180000000 00000000001156b0 (smp_vcpu_scheduled+0x18/0x40) R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 EA:3 Krnl GPRS: 000000200000007e 0000000000000000 fffffee17a671fd8 0000000300000015 ffffffff80000000 00000000005dfde8 07000003f7f80e00 000000004fa4e800 000000036ce8d8f8 000000036ce8d9c0 00000003ece8fe00 ffffffff969c9e93 00000003fffffffd 000000036ce8da10 00000000003bf134 00000003f3b07918 Krnl Code: 00000000001156a2: a7190000 lghi %r1,0 00000000001156a6: a7380015 lhi %r3,21 #00000000001156aa: e32050000008 ag %r2,0(%r5) >00000000001156b0: 482022b0 lh %r2,688(%r2) 00000000001156b4: ae123000 sigp %r1,%r2,0(%r3) 00000000001156b8: b2220020 ipm %r2 00000000001156bc: 8820001c srl %r2,28 00000000001156c0: c02700000001 xilf %r2,1 Call Trace: ([<0000000000000000>] 0x0) [<000003ff807bdb8e>] zfcp_fsf_fcp_cmnd_handler+0x3de/0x490 [zfcp] [<000003ff807be30a>] zfcp_fsf_req_complete+0x252/0x800 [zfcp] [<000003ff807c0a48>] zfcp_fsf_reqid_check+0xe8/0x190 [zfcp] [<000003ff807c194e>] zfcp_qdio_int_resp+0x66/0x188 [zfcp] [<000003ff80440c64>] qdio_kick_handler+0xdc/0x310 [qdio] [<000003ff804463d0>] __tiqdio_inbound_processing+0xf8/0xcd8 [qdio] [<0000000000141fd4>] tasklet_action+0x9c/0x170 [<0000000000141550>] __do_softirq+0xe8/0x258 [<000000000010ce0a>] do_softirq+0xba/0xc0 [<000000000014187c>] irq_exit+0xc4/0xe8 [<000000000046b526>] do_IRQ+0x146/0x1d8 [<00000000005d6a3c>] io_return+0x0/0x8 [<00000000005d6422>] vtime_stop_cpu+0x4a/0xa0 ([<0000000000000000>] 0x0) [<0000000000103d8a>] arch_cpu_idle+0xa2/0xb0 [<0000000000197f94>] cpu_startup_entry+0x13c/0x1f8 [<0000000000114782>] smp_start_secondary+0xda/0xe8 [<00000000005d6efe>] restart_int_handler+0x56/0x6c [<0000000000000000>] 0x0 Last Breaking-Event-Address: [<00000000003bf12e>] arch_spin_lock_wait+0x56/0xb0 Suggested-by: Steffen Maier <maier@linux.vnet.ibm.com> Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com> Fixes: ea127f9754 ("[PATCH] s390 (7/7): zfcp host adapter.") (tglx/history.git) Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Martin Schwidefsky: "A few more s390 patches for 4.9: - a fix for an overflow in the dasd driver reported by UBSAN - fix a regression and add hotplug memory to the zone movable again - add ignore defines for the pkey system calls - fix the ouput of the merged stack tracer - replace printk with pr_cont in arch/s390 where appropriate - remove the arch specific return_address function again - ignore reserved channel paths at boot time - add a missing hugetlb_bad_size call to the arch backend" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/mm: fix zone calculation in arch_add_memory() s390/dumpstack: use pr_cont within show_stack and die s390/dumpstack: get rid of return_address again s390/disassambler: use pr_cont where appropriate s390/dumpstack: use pr_cont where appropriate s390/dumpstack: restore reliable indicator for call traces s390/mm: use hugetlb_bad_size() s390/cio: don't register chpids in reserved state s390: ignore pkey system calls s390/dasd: avoid undefined behaviour
2016-10-17s390/cio: don't register chpids in reserved stateSebastian Ott
During IPL we register all chpids that are not in the unrecognized state. This includes chpids that are not usable and chpids for which the state could not be obtained. Change that to only register chpids in the configured (usable) or standby (usable after a configure operation) state. All other chpids could only be made available by external control for which we would receive machine checks. Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2016-10-17s390/dasd: avoid undefined behaviourChristian Borntraeger
the mdc value can be quite big (like 65535), so we are in undefined territory when doing the multiplication with the (also signed) FCX_MAX_DATA_FACTOR as outlined by UBSAN: UBSAN: Undefined behaviour in drivers/s390/block/dasd_eckd.c:1678:14 signed integer overflow: 65535 * 65536 cannot be represented in type 'int' CPU: 5 PID: 183 Comm: kworker/u512:1 Not tainted 4.7.0+ #150 Workqueue: events_unbound async_run_entry_fn 000000fb8b59f900 000000fb8b59f990 0000000000000002 0000000000000000 000000fb8b59fa30 000000fb8b59f9a8 000000fb8b59f9a8 000000000011732e 00000000000000a4 0000000000a309e2 0000000000a4c072 000000000000000b 000000fb8b59f9f0 000000fb8b59f990 0000000000000000 0000000000000000 0400000000d83238 000000000011732e 000000fb8b59f990 000000fb8b59f9f0 Call Trace: ([<0000000000117260>] show_trace+0x98/0xa8) ([<00000000001172e0>] show_stack+0x70/0xf0) ([<000000000053ac96>] dump_stack+0x86/0xb8) ([<000000000057f5f8>] ubsan_epilogue+0x28/0x70) ([<000000000057fe9e>] handle_overflow+0xde/0xf0) ([<00000000006c322a>] dasd_eckd_check_characteristics+0x50a/0x550) ([<00000000006b42ca>] dasd_generic_set_online+0xba/0x380) ([<0000000000693d82>] ccw_device_set_online+0x192/0x550) ([<00000000006ac1ae>] dasd_generic_auto_online+0x2e/0x70) ([<0000000000172130>] async_run_entry_fn+0x70/0x270) ([<0000000000165a72>] process_one_work+0x26a/0x638) ([<0000000000165e8a>] worker_thread+0x4a/0x658) ([<000000000016dd9c>] kthread+0x10c/0x110) ([<00000000008963ae>] kernel_thread_starter+0x6/0xc) ([<00000000008963a8>] kernel_thread_starter+0x0/0xc) As this is a runtime value there is actually no risk of any sane compiler to detect and (ab)use this undefinedness, but let's make the multiplication defined by making mdc unsigned. Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Stefan Haberland <sth@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2016-10-14scsi: zfcp: spin_lock_irqsave() is not nestableDan Carpenter
We accidentally overwrite the original saved value of "flags" so that we can't re-enable IRQs at the end of the function. Presumably this function is mostly called with IRQs disabled or it would be obvious in testing. Fixes: aceeffbb59bb ("zfcp: trace full payload of all SAN records (req,resp,iels)") Cc: <stable@vger.kernel.org> #2.6.38+ Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-10-07Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds
Pull SCSI updates from James Bottomley: "This update includes the usual round of major driver updates (hpsa, be2iscsi, hisi_sas, zfcp, cxlflash). There's a new incarnation of hpsa called smartpqi for which a driver is added, there's some cleanup work of the ibm vscsi target and updates to libfc, plus a whole host of minor fixes and updates and finally the removal of several ISA drivers which seem not to have been used for years" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (173 commits) scsi: mvsas: Mark symbols static where possible scsi: pm8001: Mark symbols static where possible scsi: arcmsr: Simplify user_len checking scsi: fcoe: fix off by one in eth2fc_speed() scsi: dtc: remove from tree scsi: t128: remove from tree scsi: pas16: remove from tree scsi: u14-34f: remove from tree scsi: ultrastor: remove from tree scsi: in2000: remove from tree scsi: wd7000: remove from tree scsi: scsi_dh_alua: Fix memory leak in alua_rtpg() scsi: lpfc: Mark symbols static where possible scsi: hpsa: correct call to hpsa_do_reset scsi: ufs: Get a TM service response from the correct offset scsi: ibmvfc: Fix I/O hang when port is not mapped scsi: megaraid_sas: clean function declarations in megaraid_sas_base.c up scsi: ipr: Remove redundant messages at adapter init time scsi: ipr: Don't log unnecessary 9084 error details scsi: smartpqi: raid bypass lba calculation fix ...
2016-10-04Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 updates from Martin Schwidefsky: "The new features and main improvements in this merge for v4.9 - Support for the UBSAN sanitizer - Set HAVE_EFFICIENT_UNALIGNED_ACCESS, it improves the code in some places - Improvements for the in-kernel fpu code, in particular the overhead for multiple consecutive in kernel fpu users is recuded - Add a SIMD implementation for the RAID6 gen and xor operations - Add RAID6 recovery based on the XC instruction - The PCI DMA flush logic has been improved to increase the speed of the map / unmap operations - The time synchronization code has seen some updates And bug fixes all over the place" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (48 commits) s390/con3270: fix insufficient space padding s390/con3270: fix use of uninitialised data MAINTAINERS: update DASD maintainer s390/cio: fix accidental interrupt enabling during resume s390/dasd: add missing \n to end of dev_err messages s390/config: Enable config options for Docker s390/dasd: make query host access interruptible s390/dasd: fix panic during offline processing s390/dasd: fix hanging offline processing s390/pci_dma: improve lazy flush for unmap s390/pci_dma: split dma_update_trans s390/pci_dma: improve map_sg s390/pci_dma: simplify dma address calculation s390/pci_dma: remove dma address range check iommu/s390: simplify registration of I/O address translation parameters s390: migrate exception table users off module.h and onto extable.h s390: export header for CLP ioctl s390/vmur: fix irq pointer dereference in int handler s390/dasd: add missing KOBJ_CHANGE event for unformatted devices s390: enable UBSAN ...
2016-10-03Merge tag 'char-misc-4.9-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here's the "big" char and misc driver update for 4.9-rc1. Lots of little things here, all over the driver tree for subsystems that flow through me. Nothing major that I can discern, full details are in the shortlog. All have been in the linux-next tree with no reported issues" * tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (144 commits) drivers/misc/hpilo: Changes to support new security states in iLO5 FW at25: fix debug and error messaging misc/genwqe: ensure zero initialization vme: fake: remove unexpected unlock in fake_master_set() vme: fake: mark symbols static where possible spmi: pmic-arb: Return an error code if sanity check fails Drivers: hv: get rid of id in struct vmbus_channel Drivers: hv: make VMBus bus ids persistent mcb: Add a dma_device to mcb_device mcb: Enable PCI bus mastering by default mei: stop the stall timer worker if not needed clk: probe common clock drivers earlier vme: fake: fix build for 64-bit dma_addr_t ttyprintk: Neaten and simplify printing mei: me: add kaby point device ids coresight: tmc: mark symbols static where possible coresight: perf: deal with error condition properly Drivers: hv: hv_util: Avoid dynamic allocation in time synch fpga manager: Add hardware dependency to Zynq driver Drivers: hv: utils: Support TimeSync version 4.0 protocol samples. ...
2016-09-30s390/con3270: fix insufficient space paddingSascha Silbe
con3270 contains an optimisation that reduces the amount of data to be transmitted to the 3270 terminal by putting a Repeat to Address (RA) order into the data stream. The RA order itself takes up space, so con3270 only uses it if there's enough space left in the line buffer. Otherwise it just pads out the line manually. For lines that were _just_ short enough that the RA order still fit in the line buffer, the line was instead padded with an insufficient amount of spaces. This was caused by examining the size of the allocated line buffer rather than the length of the string to be displayed. For con3270_cline_end(), we just compare against the line length. For con3270_update_string() however that isn't available anymore, so we check whether the Repeat to Address order is present. Fixes: f51320a5 ("[PATCH] s390: new 3270 driver.") (tglx/history.git) Tested-by: Jing Liu <liujbjl@linux.vnet.ibm.com> Tested-by: Yang Chen <bjcyang@linux.vnet.ibm.com> Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2016-09-30s390/con3270: fix use of uninitialised dataSascha Silbe
con3270 contains an optimisation that reduces the amount of data to be transmitted to the 3270 terminal by putting a Repeat to Address (RA) order into the data stream. The RA order itself takes up space, so con3270 only uses it if there's enough space left in the line buffer. Otherwise it just pads out the line manually. For lines too long to include the RA order, one byte was left uninitialised. This was caused by an off-by-one bug in the loop that pads out the line. Since the buffer is allocated from a common pool, the single byte left uninitialised contained some previous buffer content. Usually this was just a space or some character (which can result in clutter but is otherwise harmless). Sometimes, however, it was a Repeat to Address order, messing up the entire screen layout and causing the display to send the entire buffer content on every keystroke. Fixes: f51320a5 ("[PATCH] s390: new 3270 driver.") (tglx/history.git) Reported-by: Liu Jing <liujbjl@linux.vnet.ibm.com> Tested-by: Jing Liu <liujbjl@linux.vnet.ibm.com> Tested-by: Yang Chen <bjcyang@linux.vnet.ibm.com> Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2016-09-30s390/cio: fix accidental interrupt enabling during resumeSebastian Ott
Since commit 9f3d6d7 chsc_get_channel_measurement_chars is called with interrupts disabled during resume from hibernate. Since this function used spin_unlock_irq, interrupts have been enabled accidentally. Fix this by using the irqsave variant. Since we can't guarantee the IRQ-enablement state for all (future/ external) callers, change the locking in related functions to prevent similar bugs in the future. Fixes: 9f3d6d7 ("s390/cio: update measurement characteristics") Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2016-09-28s390/dasd: add missing \n to end of dev_err messagesColin Ian King
Trival fix, dev_err messages are missing a \n, so add it. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2016-09-26s390/dasd: make query host access interruptibleStefan Haberland
If the DASD device gets blocked for any reason, e.g. because it is reserved somewhere, the host_access_count sysfs entry or the host_access_list debugfs entry may sleep forever. Make it interruptible so that userspace can use ^C to abort the operation. Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2016-09-26s390/dasd: fix panic during offline processingStefan Haberland
A DASD device consists of the device itself and a discipline with a corresponding private structure. These fields are set up during online processing right after the device is created and before it is processed by the state machine and made available for I/O. During offline processing the discipline pointer and the private data gets freed within the state machine and without protection of the existing reference count. This might lead to a kernel panic because a function might have taken a device reference and accesses the discipline pointer and/or private data of the device while this is already freed. Fix by freeing the discipline pointer and the private data after ensuring that there is no reference to the device left. Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2016-09-26s390/dasd: fix hanging offline processingStefan Haberland
Internal I/O is processed by the _sleep_on_function which might wait for a device to get operational. During offline processing this will never happen and therefore the refcount of the device will not drop to zero and the offline processing blocks as well. Fix by letting requests fail in the _sleep_on function during offline processing. No further handling of the requests is necessary since this is internal I/O and the device is thrown away afterwards. Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2016-09-20s390/vmur: fix irq pointer dereference in int handlerSebastian Ott
"irq" in vmur's int handler can be an error pointer. Don't dereference this pointer in that case. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-12 04:06:36 +0000