summaryrefslogtreecommitdiff
path: root/drivers/tty/serial/max310x.c
AgeCommit message (Collapse)Author
2019-12-05serial: max310x: Fix tx_empty() callbackAlexander Shiyan
[ Upstream commit a8da3c7873ea57acb8f9cea58c0af477522965aa ] Function max310x_tx_empty() accesses the IRQSTS register, which is cleared by IC when reading, so if there is an interrupt status, we will lose it. This patch implement the transmitter check only by the current FIFO level. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-07-31tty: max310x: Fix invalid baudrate divisors calculatorSerge Semin
[ Upstream commit 35240ba26a932b279a513f66fa4cabfd7af55221 ] Current calculator doesn't do it' job quite correct. First of all the max310x baud-rates generator supports the divisor being less than 16. In this case the x2/x4 modes can be used to double or quadruple the reference frequency. But the current baud-rate setter function just filters all these modes out by the first condition and setups these modes only if there is a clocks-baud division remainder. The former doesn't seem right at all, since enabling the x2/x4 modes causes the line noise tolerance reduction and should be only used as a last resort to enable a requested too high baud-rate. Finally the fraction is supposed to be calculated from D = Fref/(c*baud) formulae, but not from D % 16, which causes the precision loss. So to speak the current baud-rate calculator code works well only if the baud perfectly fits to the uart reference input frequency. Lets fix the calculator by implementing the algo fully compliant with the fractional baud-rate generator described in the datasheet: D = Fref / (c*baud), where c={16,8,4} is the x1/x2/x4 rate mode respectively, Fref - reference input frequency. The divisor fraction is calculated from the same formulae, but making sure it is found with a resolution of 0.0625 (four bits). Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-06-09tty: max310x: Fix external crystal register setupJoe Burmeister
commit 5d24f455c182d5116dd5db8e1dc501115ecc9c2c upstream. The datasheet states: Bit 4: ClockEnSet the ClockEn bit high to enable an external clocking (crystal or clock generator at XIN). Set the ClockEn bit to 0 to disable clocking Bit 1: CrystalEnSet the CrystalEn bit high to enable the crystal oscillator. When using an external clock source at XIN, CrystalEn must be set low. The bit 4, MAX310X_CLKSRC_EXTCLK_BIT, should be set and was not. This was required to make the MAX3107 with an external crystal on our board able to send or receive data. Signed-off-by: Joe Burmeister <joe.burmeister@devtank.co.uk> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-03serial: max310x: Fix to avoid potential NULL pointer dereferenceAditya Pakki
commit 3a10e3dd52e80b9a97a3346020024d17b2c272d6 upstream. of_match_device can return a NULL pointer when matching device is not found. This patch avoids a scenario causing NULL pointer derefernce. Signed-off-by: Aditya Pakki <pakki001@umn.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-12serial: max310x: Add support for newer silicon revisionsAlexander Shiyan
New IC MAX14830 has 0xB4 silicon revision ID. This patch adds support for such ICs. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-15serial: max310x: Set IRQF_TRIGGER_FALLING flag when dev.of_node is not NULLLiu Xiang
When dev.of_node is not NULL, we also need to set IRQF_TRIGGER_FALLING flag, otherwise it may cause uncertain interrupts. Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-25serial: max310x: Assign port line automaticallyAlexander Shiyan
This patch makes assignment of port line automatically, so now user allow to use several MAX310X chips. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-25serial: max310x: Unregister UARTs on errorAlexander Shiyan
Add uart_remove_one_port() for error path. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-25serial: max310x: Remove duplicate bits definitionAlexander Shiyan
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-25serial: max310x: Register UART driver at module_initAlexander Shiyan
This patch moves UART registration at module_init initcall, so this should helps to add multiple chip support in the future. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-25serial: max310x: Using resource-managed function for GPIOAlexander Shiyan
Use resource managed functions devm_gpiochip_add_data() to make error & exit path a bit simpler. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-25serial: max310x: Fix RS485 handlingAlexander Shiyan
RS485 IOCTLs uses spinlocks, so move regmap functions into a separate work queue. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-04-26serial: max310x: use gpiochip data pointerLinus Walleij
This makes the driver use the data pointer added to the gpio_chip to store a pointer to the state container instead of relying on container_of(). Cc: Jiri Slaby <jslaby@suse.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-19gpio: change member .dev to .parentLinus Walleij
The name .dev in a struct is normally reserved for a struct device that is let us say a superclass to the thing described by the struct. struct gpio_chip stands out by confusingly using a struct device *dev to point to the parent device (such as a platform_device) that represents the hardware. As we want to give gpio_chip:s real devices, this is not working. We need to rename this member to parent. This was done by two coccinelle scripts, I guess it is possible to combine them into one, but I don't know such stuff. They look like this: @@ struct gpio_chip *var; @@ -var->dev +var->parent and: @@ struct gpio_chip var; @@ -var.dev +var.parent and: @@ struct bgpio_chip *var; @@ -var->gc.dev +var->gc.parent Plus a few instances of bgpio that I couldn't figure out how to teach Coccinelle to rewrite. This patch hits all over the place, but I *strongly* prefer this solution to any piecemal approaches that just exercise patch mechanics all over the place. It mainly hits drivers/gpio and drivers/pinctrl which is my own backyard anyway. Cc: Haavard Skinnemoen <hskinnemoen@gmail.com> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Alek Du <alek.du@intel.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-28spi: Drop owner assignment from spi_driversAndrew F. Davis
An spi_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Andrew F. Davis <afd@ti.com> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2014-11-06drivers/max310: Use the rs485 functions on serial_coreRicardo Ribalda Delgado
In order to unify all the rs485 ioctl handling Use the implementation of TIOC[GS]RS485 ioctl handling on serial_core. Reviewed-by: Alan Cox <alan@linux.intel.com> Cc: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05serial/max310x: Remove obsolete #ifset TIOC[SG]RS485Ricardo Ribalda Delgado
Commit e676253b19b2 ("serial/8250: Add support for RS485 IOCTLs") added references to TIOC[SG]RS48 on 8250_core.c. This change triggered the need to define them in all the arches that uses tty/serial. This made #ifdef TIOC[SG]RS48 obsolete. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.cz> Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05max310x: max3109_detect should use indirect addressing in SPI mode for REVID ↵Gregory Hermant
register This patch allows to read the REV_ID register in SPI mode and consequently to properly detect the max3109. Indeed in SPI mode, this register is only accessible by using indirect addressing. Signed-off-by: Gregory Hermant <gregory.hermant@calao-systems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-09-18driver:gpio remove all usage of gpio_remove retval in driverabdoulaye berthe
this remove all reference to gpio_remove retval in all driver except pinctrl and gpio. the same thing is done for gpio and pinctrl in two different patches. Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com> Acked-by: Michael Büsch <m@bues.ch> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com> Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-07-09serial: treewide: Remove empty implementations of enable_ms()Alexander Shiyan
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-19serial: Fix IGNBRK handlingPeter Hurley
If IGNBRK is set without either BRKINT or PARMRK set, some uart drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the line discipline, when it should send either nothing or the TTYBREAK flag set. This happens because the read_status_mask masks out the BI condition, which uart_insert_char() then interprets as a normal 0x00 byte. SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General Terminal Interface - Input Modes, states: "If IGNBRK is set, a break condition detected on input shall be ignored; that is, not put on the input queue and therefore not read by any process." Fix read_status_mask to include the BI bit if IGNBRK is set; the lsr status retains the BI bit if a BREAK is recv'd, which is subsequently ignored in uart_insert_char() when masked with the ignore_status_mask. Affected drivers: 8250 - all serial_txx9 mfd amba-pl010 amba-pl011 atmel_serial bfin_uart dz ip22zilog max310x mxs-auart netx-serial pnx8xxx_uart pxa sb1250-duart sccnxp serial_ks8695 sirfsoc_uart st-asc vr41xx_siu zs sunzilog fsl_lpuart sunsab ucc_uart bcm63xx_uart sunsu efm32-uart pmac_zilog mpsc msm_serial m32r_sio Unaffected drivers: omap-serial rp2 sa1100 imx icom Annotated for fixes: altera_uart mcf Drivers without break detection: 21285 xilinx-uartps altera_jtaguart apbuart arc-uart clps711x max3100 uartlite msm_serial_hs nwpserial lantiq vt8500_serial Unknown: samsung mpc52xx_uart bfin_sport_uart cpm_uart/core Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag' Reported-by: Ivan <athlon_@mail.ru> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-03-17serial: max310x: Add missing #include <linux/uaccess.h>Geert Uytterhoeven
cris allmodconfig: drivers/tty/serial/max310x.c: In function 'max310x_ioctl': drivers/tty/serial/max310x.c:885:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration] drivers/tty/serial/max310x.c:916:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration] Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-15serial: max310x: Fix sparse warningsAlexander Shiyan
sparse warnings: (new ones prefixed by >>) >> drivers/tty/serial/max310x.c:906:45: sparse: incorrect type in argument 2 (different address spaces) drivers/tty/serial/max310x.c:906:45: expected void const [noderef] <asn:1>*from drivers/tty/serial/max310x.c:906:45: got struct serial_rs485 *<noident> >> drivers/tty/serial/max310x.c:938:35: sparse: incorrect type in argument 1 (different address spaces) drivers/tty/serial/max310x.c:938:35: expected void [noderef] <asn:1>*to drivers/tty/serial/max310x.c:938:35: got struct serial_rs485 *<noident> Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Fix build errorAlexander Shiyan
This is a temporary solution to fix following issue: config: make ARCH=alpha allyesconfig All error/warnings: drivers/tty/serial/max310x.c: In function 'max310x_ioctl': >> drivers/tty/serial/max310x.c:905:7: error: 'TIOCSRS485' undeclared (first use in this function) drivers/tty/serial/max310x.c:905:7: note: each undeclared identifier is reported only once for each function it appears in >> drivers/tty/serial/max310x.c:906:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration] >> drivers/tty/serial/max310x.c:929:7: error: 'TIOCGRS485' undeclared (first use in this function) >> drivers/tty/serial/max310x.c:938:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration] cc1: some warnings being treated as errors Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13Revert "serial: max310x: Fix build error"Greg Kroah-Hartman
This reverts commit e3c6ea9b1b81b87de96c01d5d37764009d546636 as it didn't help anything, and caused more problems than expected. Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Fix build warningAlexander Shiyan
config: x86_64-randconfig-x006 (attached as .config) All warnings: drivers/tty/serial/max310x.c: In function 'max310x_probe': >> drivers/tty/serial/max310x.c:1240:1: warning: label 'out_uart' defined but not used [-Wunused-label] Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Fix build errorAlexander Shiyan
config: make ARCH=alpha allyesconfig All error/warnings: drivers/tty/serial/max310x.c: In function 'max310x_ioctl': >> drivers/tty/serial/max310x.c:905:7: error: 'TIOCSRS485' undeclared (first use in this function) drivers/tty/serial/max310x.c:905:7: note: each undeclared identifier is reported only once for each function it appears in >> drivers/tty/serial/max310x.c:906:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration] >> drivers/tty/serial/max310x.c:929:7: error: 'TIOCGRS485' undeclared (first use in this function) >> drivers/tty/serial/max310x.c:938:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration] cc1: some warnings being treated as errors Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Add devicetree supportAlexander Shiyan
This patch adds devicetree support for the MAX310X serial driver. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Driver cleanupAlexander Shiyan
This patch removes some unused definitions from driver code and sort #includes alphabetically. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Add support for RS-485 modeAlexander Shiyan
This patch adds support for RS-485 (TIOCSRS485/TIOCGRS485) IOCTLs. As a result this patch eliminate private driver header. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Add missing mutex_destroy() on driver exitAlexander Shiyan
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Always use dynamic GPIO ID assignmentAlexander Shiyan
Always register GPIOs and use dynamic GPIO ID assignment. This is no much worth if GPIOs is not used, but helps remove private driver header and add DT support in the future. Additionally, patch adds missing uart_unregister_driver() call if probe() fails. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Migrate to CLK APIAlexander Shiyan
This patch removes "frequency" parameter from MAX310X platform_data and uses CLK API for getting clock. Clock type (XTAL/OSC) is determined by clk name. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Move all SPI-dependent stuff in one placeAlexander Shiyan
Patch move all SPI-dependent stuff in one place. This include move PM-function definitions out of CONFIG_SPI_MASTER and move regmap initialization out of common probe into CONFIG_SPI_MASTER which may help to add I2C support in the future for this driver. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Remove IRQ validationAlexander Shiyan
This patch removes excess IRQ checks at driver probe(). IRQ validation is already provided by request_threaded_irq(). Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Add the loopback mode supportAlexander Shiyan
This patch replaces loopback mode support from platform data to dynamic setup with TIOCMSET ioctl. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Remove excess port configure at startupAlexander Shiyan
Serial core calls set_termios() after port startup, so there are no reason to setup port twice. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Remove init() and exit() callbacksAlexander Shiyan
These callbacks were previously used for the IC power initialization. If this initialization will be needed in the future, it should be implemented with the regulator API. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-02-13serial: max310x: Setup baud rate generator more preciselyAlexander Shiyan
This patch provide more precisely setup of baud rate generator. If the result of division has a remainder, we use the multiplier for the base frequency. Additionally, we report result baud rate back to serial core. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-10-16tty: Remove unnecessary semicolonsJoe Perches
These aren't necessary after switch and while blocks. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-29serial: max310x: Fix dev_pm_opsAlexander Shiyan
This patch fixes wrong dev_pm_ops which caused by commit: serial: max310x: Driver rework. CC drivers/tty/serial/max310x.o LD drivers/video/fb.o CC drivers/w1/slaves/w1_ds2433.o CC drivers/w1/slaves/w1_ds2760.o CC drivers/xen/balloon.o CC drivers/video/backlight/adp8870_bl.o drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default] drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.suspend') [enabled by default] drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default] drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.resume') [enabled by default] drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default] drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.freeze') [enabled by default] drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default] drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.thaw') [enabled by default] drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default] drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.poweroff') [enabled by default] drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default] drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.restore') [enabled by default] Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-26serial: max310x: Add MAX14830 supportAlexander Shiyan
This patch adds support for MAX14830 (advanced quad universal asynchronous receiver-transmitter) into max310x driver. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-26serial: max310x: Add MAX3109 supportAlexander Shiyan
This patch adds support for MAX3109 (advanced dual universal asynchronous receiver-transmitter) into max310x driver. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-26serial: max310x: Driver reworkAlexander Shiyan
This patch rework max310x driver. Major changes have been made: - Prepare driver to support ICs with more than one UART. - Prepare driver to support work with I2C-bus. The patch changes almost every function and can not be divided into parts. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-18tty: max310x: Use dev_pm_opsLars-Peter Clausen
Use dev_pm_ops instead of the deprecated legacy suspend/resume for the max310x driver. Cc: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-15TTY: switch tty_flip_buffer_pushJiri Slaby
Now, we start converting tty buffer functions to actually use tty_port. This will allow us to get rid of the need of tty in many call sites. Only tty_port will needed and hence no more tty_port_tty_get in those paths. Now, the one where most of tty_port_tty_get gets removed: tty_flip_buffer_push. IOW we also closed all the races in drivers not using tty_port_tty_get at all yet. Also we move tty_flip_buffer_push declaration from include/linux/tty.h to include/linux/tty_flip.h to all others while we are changing it anyway. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-26serial: max310x: Setup missing "can_sleep" field for GPIOAlexander Shiyan
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-21tty: remove use of __devexitBill Pemberton
CONFIG_HOTPLUG is going away as an option so __devexit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Jiri Slaby <jirislaby@gmail.com> Cc: Alan Cox <alan@linux.intel.com> Acked-by: Tobias Klauser <tklauser@distanz.ch> Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com> Cc: Daniel Walker <dwalker@fifo99.com> Cc: Bryan Huntsman <bryanh@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Tony Prisk <linux@prisktech.co.nz> Acked-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-21tty: remove use of __devinitBill Pemberton
CONFIG_HOTPLUG is going away as an option so __devinit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Jiri Slaby <jirislaby@gmail.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Tony Prisk <linux@prisktech.co.nz> Acked-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-21tty: serial: remove use of __devexit_pBill Pemberton
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Alan Cox <alan@linux.intel.com> Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Tony Prisk <linux@prisktech.co.nz> Acked-by: Tobias Klauser <tklauser@distanz.ch> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-05-18 01:47:54 +0000