| Age | Commit message (Collapse) | Author |
|---|
|
commit 4879efb34f7d49235fac334d76d9c6a77a021413 upstream.
dwc3-exynos has two problems during init if the regulators are slow
to come up (for instance if the I2C bus driver is not on the initramfs)
and return probe deferral. First, every time this happens, the driver
leaks the USB phys created; they need to be deallocated on error.
Second, since the phy devices are created before the regulators fail,
this means that there's a new device to re-trigger deferred probing,
which causes it to essentially go into a busy loop of re-probing the
device until the regulators come up.
Move the phy creation to after the regulators have succeeded, and also
fix cleanup on failure. On my ODROID XU4 system (with Debian's initramfs
which doesn't contain the I2C driver), this reduces the number of probe
attempts (for each of the two controllers) from more than 2000 to eight.
Signed-off-by: Steinar H. Gunderson <sesse@google.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Fixes: d720f057fda4 ("usb: dwc3: exynos: add nop transceiver support")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8a15a9650694feaa0dabf197b0c94d37cd3fb42 upstream.
There are three EHCI controllers on Tegra SoCs, each with its own reset
line. However, the first controller contains a set of UTMI configuration
registers that are shared with its siblings. These registers will only
be reset as part of the first controller's reset. For proper operation
it must be ensured that the UTMI configuration registers are reset
before any of the EHCI controllers are enabled, irrespective of the
probe order.
Commit a47cc24cd1e5 ("USB: EHCI: tegra: Fix probe order issue leading to
broken USB") introduced code that ensures the first controller is always
reset before setting up any of the controllers, and is never again reset
afterwards.
This code, however, grabs the wrong reset. Each EHCI controller has two
reset controls attached: 1) the USB controller reset and 2) the UTMI
pads reset (really the first controller's reset). In order to reset the
UTMI pads registers the code must grab the second reset, but instead it
grabbing the first.
Fixes: a47cc24cd1e5 ("USB: EHCI: tegra: Fix probe order issue leading to broken USB")
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d246dcb2331c5783743720e6510892eb1d2801d9 upstream.
[ 40.467381] =============================================
[ 40.473013] [ INFO: possible recursive locking detected ]
[ 40.478651] 4.6.0-08691-g7f3db9a #37 Not tainted
[ 40.483466] ---------------------------------------------
[ 40.489098] usb/733 is trying to acquire lock:
[ 40.493734] (&(&dev->lock)->rlock){-.....}, at: [<bf129288>] ep0_complete+0x18/0xdc [gadgetfs]
[ 40.502882]
[ 40.502882] but task is already holding lock:
[ 40.508967] (&(&dev->lock)->rlock){-.....}, at: [<bf12a420>] ep0_read+0x20/0x5e0 [gadgetfs]
[ 40.517811]
[ 40.517811] other info that might help us debug this:
[ 40.524623] Possible unsafe locking scenario:
[ 40.524623]
[ 40.530798] CPU0
[ 40.533346] ----
[ 40.535894] lock(&(&dev->lock)->rlock);
[ 40.540088] lock(&(&dev->lock)->rlock);
[ 40.544284]
[ 40.544284] *** DEADLOCK ***
[ 40.544284]
[ 40.550461] May be due to missing lock nesting notation
[ 40.550461]
[ 40.557544] 2 locks held by usb/733:
[ 40.561271] #0: (&f->f_pos_lock){+.+.+.}, at: [<c02a6114>] __fdget_pos+0x40/0x48
[ 40.569219] #1: (&(&dev->lock)->rlock){-.....}, at: [<bf12a420>] ep0_read+0x20/0x5e0 [gadgetfs]
[ 40.578523]
[ 40.578523] stack backtrace:
[ 40.583075] CPU: 0 PID: 733 Comm: usb Not tainted 4.6.0-08691-g7f3db9a #37
[ 40.590246] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 40.596625] [<c010ffbc>] (unwind_backtrace) from [<c010c1bc>] (show_stack+0x10/0x14)
[ 40.604718] [<c010c1bc>] (show_stack) from [<c04207fc>] (dump_stack+0xb0/0xe4)
[ 40.612267] [<c04207fc>] (dump_stack) from [<c01886ec>] (__lock_acquire+0xf68/0x1994)
[ 40.620440] [<c01886ec>] (__lock_acquire) from [<c0189528>] (lock_acquire+0xd8/0x238)
[ 40.628621] [<c0189528>] (lock_acquire) from [<c06ad6b4>] (_raw_spin_lock_irqsave+0x38/0x4c)
[ 40.637440] [<c06ad6b4>] (_raw_spin_lock_irqsave) from [<bf129288>] (ep0_complete+0x18/0xdc [gadgetfs])
[ 40.647339] [<bf129288>] (ep0_complete [gadgetfs]) from [<bf10a728>] (musb_g_giveback+0x118/0x1b0 [musb_hdrc])
[ 40.657842] [<bf10a728>] (musb_g_giveback [musb_hdrc]) from [<bf108768>] (musb_g_ep0_queue+0x16c/0x188 [musb_hdrc])
[ 40.668772] [<bf108768>] (musb_g_ep0_queue [musb_hdrc]) from [<bf12a944>] (ep0_read+0x544/0x5e0 [gadgetfs])
[ 40.678963] [<bf12a944>] (ep0_read [gadgetfs]) from [<c0284470>] (__vfs_read+0x20/0x110)
[ 40.687414] [<c0284470>] (__vfs_read) from [<c0285324>] (vfs_read+0x88/0x114)
[ 40.694864] [<c0285324>] (vfs_read) from [<c0286150>] (SyS_read+0x44/0x9c)
[ 40.702051] [<c0286150>] (SyS_read) from [<c0107820>] (ret_fast_syscall+0x0/0x1c)
This is caused by the spinlock bug in ep0_read().
Fix the two other deadlock sources in gadgetfs_setup() too.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcb21ad4385731b7fc3ef39d255685f2f63c8c5d upstream.
parport subsystem has introduced parport_del_port() to delete a port
when it is going away. Without parport_del_port() the registered port
will not be unregistered.
To reproduce and verify the error:
Command to be used is : ls /sys/bus/parport/devices
1) without the device attached there is no output as there is no
registered parport.
2) Attach the device, and the command will show "parport0".
3) Remove the device and the command still shows "parport0".
4) Attach the device again and we get "parport1".
With the patch applied:
1) without the device attached there is no output as there is no
registered parport.
2) Attach the device, and the command will show "parport0".
3) Remove the device and there is no output as "parport0" is now
removed.
4) Attach device again to get "parport0" again.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3425aa03f484d45dc21e0e791c2f6c74ea656421 upstream.
If commands timeout we mark them for abortion, then stop the command
ring, and turn the commands to no-ops and finally restart the command
ring.
If the host is working properly the no-op commands will finish and
pending completions are called.
If we notice the host is failing, driver clears the command ring and
completes, deletes and frees all pending commands.
There are two separate cases reported where host is believed to work
properly but is not. In the first case we successfully stop the ring
but no abort or stop command ring event is ever sent and host locks up.
The second case is if a host is removed, command times out and driver
believes the ring is stopped, and assumes it will be restarted, but
actually ends up timing out on the same command forever.
If one of the pending commands has the xhci->mutex held it will block
xhci_stop() in the remove codepath which otherwise would cleanup pending
commands.
Add a check that clears all pending commands in case host is removed,
or we are stuck timing out on the same command. Also restart the
command timeout timer when stopping the command ring to ensure we
recive an ring stop/abort event.
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d95815ba6a0f287213118c136e64d8c56daeaeab upstream.
I got one of these cards for testing uas with, it seems that with streams
it dma-s all over the place, corrupting memory. On my first tests it
managed to dma over the BIOS of the motherboard somehow and completely
bricked it.
Tests on another motherboard show that it does work with streams disabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit de95c40d5beaa47f6dc8fe9ac4159b4672b51523 upstream.
On some platforms, the clocks might be registered by a platform
driver. When this is the case, the clock platform driver may very well
be probed after xhci-plat, in which case the first probe() invocation
of xhci-plat will receive -EPROBE_DEFER as the return value of
devm_clk_get().
The current code handles that as a normal error, and simply assumes
that this means that the system doesn't have a clock for the XHCI
controller, and continues probing without calling
clk_prepare_enable(). Unfortunately, this doesn't work on systems
where the XHCI controller does have a clock, but that clock is
provided by another platform driver. In order to fix this situation,
we handle the -EPROBE_DEFER error condition specially, and abort the
XHCI controller probe(). It will be retried later automatically, the
clock will be available, devm_clk_get() will succeed, and the probe()
will continue with the clock prepared and enabled as expected.
In practice, such issue is seen on the ARM64 Marvell 7K/8K platform,
where the clocks are registered by a platform driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 27a41a83ec54d0edfcaf079310244e7f013a7701 upstream.
Under stress occasions some TI devices might not return early when
reading the status register during the quirk invocation of xhci_irq made
by usb_hcd_pci_remove. This means that instead of returning, we end up
handling this interruption in the middle of a shutdown. Since
xhci->event_ring has already been freed in xhci_mem_cleanup, we end up
accessing freed memory, causing the Oops below.
commit 8c24d6d7b09d ("usb: xhci: stop everything on the first call to
xhci_stop") is the one that changed the instant in which we clean up the
event queue when stopping a device. Before, we didn't call
xhci_mem_cleanup at the first time xhci_stop is executed (for the shared
HCD), instead, we only did it after the invocation for the primary HCD,
much later at the removal path. The code flow for this oops looks like
this:
xhci_pci_remove()
usb_remove_hcd(xhci->shared)
xhci_stop(xhci->shared)
xhci_halt()
xhci_mem_cleanup(xhci); // Free the event_queue
usb_hcd_pci_remove(primary)
xhci_irq() // Access the event_queue if STS_EINT is set. Crash.
xhci_stop()
xhci_halt()
// return early
The fix modifies xhci_stop to only cleanup the xhci data when releasing
the primary HCD. This way, we still have the event_queue configured
when invoking xhci_irq. We still halt the device on the first call to
xhci_stop, though.
I could reproduce this issue several times on the mainline kernel by
doing a bind-unbind stress test with a specific storage gadget attached.
I also ran the same test over-night with my patch applied and didn't
observe the issue anymore.
[ 113.334124] Unable to handle kernel paging request for data at address 0x00000028
[ 113.335514] Faulting instruction address: 0xd00000000d4f767c
[ 113.336839] Oops: Kernel access of bad area, sig: 11 [#1]
[ 113.338214] SMP NR_CPUS=1024 NUMA PowerNV
[c000000efe47ba90] c000000000720850 usb_hcd_irq+0x50/0x80
[c000000efe47bac0] c00000000073d328 usb_hcd_pci_remove+0x68/0x1f0
[c000000efe47bb00] d00000000daf0128 xhci_pci_remove+0x78/0xb0
[xhci_pci]
[c000000efe47bb30] c00000000055cf70 pci_device_remove+0x70/0x110
[c000000efe47bb70] c00000000061c6bc __device_release_driver+0xbc/0x190
[c000000efe47bba0] c00000000061c7d0 device_release_driver+0x40/0x70
[c000000efe47bbd0] c000000000619510 unbind_store+0x120/0x150
[c000000efe47bc20] c0000000006183c4 drv_attr_store+0x64/0xa0
[c000000efe47bc60] c00000000039f1d0 sysfs_kf_write+0x80/0xb0
[c000000efe47bca0] c00000000039e14c kernfs_fop_write+0x18c/0x1f0
[c000000efe47bcf0] c0000000002e962c __vfs_write+0x6c/0x190
[c000000efe47bd90] c0000000002eab40 vfs_write+0xc0/0x200
[c000000efe47bde0] c0000000002ec85c SyS_write+0x6c/0x110
[c000000efe47be30] c000000000009260 system_call+0x38/0x108
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: joel@jms.id.au
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 04471eb8c3158c0ad9df4b24da845a63b2e8f23a upstream.
Incorrect cppi dma channel is referenced in musb_rx_dma_iso_cppi41(),
which causes kernel NULL pointer reference oops later when calling
cppi41_dma_channel_program().
Fixes: 069a3fd (usb: musb: Remove ifdefs for musb_host_rx in musb_host.c
part1)
Reported-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f3eec0cf784e0d6c47822ca6b66df3d5812af7e6 upstream.
shared_fifo endpoints would only get a previous tx state cleared
out, the rx state was only cleared for non shared_fifo endpoints
Change this so that the rx state is cleared for all endpoints.
This addresses an issue that resulted in rx packets being dropped
silently.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b2c17f829545df27a910e8d82e133c21c9a8c9c upstream.
Ensure that the endpoint is stopped by clearing REQPKT before
clearing DATAERR_NAKTIMEOUT before rotating the queue on the
dedicated bulk endpoint.
This addresses an issue where a race could result in the endpoint
receiving data before it was reprogrammed resulting in a warning
about such data from musb_rx_reinit before it was thrown away.
The data thrown away was a valid packet that had been correctly
ACKed which meant the host and device got out of sync.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84ac5d1140f716a616522f952734e850448d2556 upstream.
If the session bit was not set in the backup of devctl register,
restoring devctl would clear the session bit. Therefor, only restore
devctl register when the session bit was set in the backup.
This solves the device enumeration failure in otg mode exposed by commit
56f487c (PM / Runtime: Update last_busy in rpm_resume).
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 32cb0b37098f4beeff5ad9e325f11b42a6ede56c upstream.
The Acer C120 LED Projector is a USB-3 connected pico projector which
takes both its power and video data from USB-3.
In combination with some hubs this device does not play well with
lpm, so disable lpm for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 81099f97bd31e25ff2719a435b1860fc3876122f upstream.
Properly sort all the entries by vendor id.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 593224ea77b1ca842f45cf76f4deeef44dfbacd1 upstream.
Commit 198de51dbc34 ("USB: uas: Limit qdepth at the scsi-host level")
removed the scsi_change_queue_depth() call from uas_slave_configure()
assuming that the slave would inherit the host's queue_depth, which
that commit sets to the same value.
This is incorrect, without the scsi_change_queue_depth() call the slave's
queue_depth defaults to 1, introducing a performance regression.
This commit restores the call, fixing the performance regression.
Fixes: 198de51dbc34 ("USB: uas: Limit qdepth at the scsi-host level")
Reported-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 19ced623db2fe91604d69f7d86b03144c5107739 upstream.
The hash buffer is really HASH_BLOCK_SIZE bytes, someone
must have thought that memmove takes n*u32 words by mistake.
Tests work as good/bad as before after this patch.
Cc: Joakim Bech <joakim.bech@linaro.org>
Reported-by: David Binderman <linuxdev.baldrick@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 12d3f49e1ffbbf8cbbb60acae5a21103c5c841ac upstream.
All of the VMX AES ciphers (AES, AES-CBC and AES-CTR) are set at
priority 1000. Unfortunately this means we never use AES-CBC and
AES-CTR, because the base AES-CBC cipher that is implemented on
top of AES inherits its priority.
To fix this, AES-CBC and AES-CTR have to be a higher priority. Set
them to 2000.
Testing on a POWER8 with:
cryptsetup benchmark --cipher aes --key-size 256
Shows decryption speed increase from 402.4 MB/s to 3069.2 MB/s,
over 7x faster. Thanks to Mike Strosaker for helping me debug
this issue.
Fixes: 8c755ace357c ("crypto: vmx - Adding CBC routines for VMX module")
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 881d0327db37ad917a367c77aff1afa1ee41e0a9 ]
Note: This is a verified backported patch for stable 4.4 kernel, and it
could also be applied to 4.3/4.2/4.1/3.18/3.16
There is a problem with alx devices, that the network link will be
lost in 1-5 minutes after the device is up.
>From debugging without datasheet, we found the error always
happen when the DMA RX address is set to 0x....fc0, which is very
likely to be a HW/silicon problem.
This patch will apply rx skb with 64 bytes longer space, and if the
allocated skb has a 0x...fc0 address, it will use skb_resever(skb, 64)
to advance the address, so that the RX overflow can be avoided.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70761
Signed-off-by: Feng Tang <feng.tang@intel.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Tested-by: Ole Lukoie <olelukoie@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6bdaa5e9ed39b3b3328f35d218e8ad5a99cfc4d2 ]
On AT91 SoCs, the User Register (USRIO) exposes a switch to configure the
"Reduced" or "Traditional" version of the Media Independent Interface
(RMII vs. MII or RGMII vs. GMII).
As on the older EMAC version, on GMAC, this switch is set by default to the
non-reduced type of interface, so use the existing capability and extend it to
GMII as well. We then keep the current logic in the macb_init() function.
The capabilities of sama5d2, sama5d4 and sama5d3 GEM interface are updated in
the macb_config structure to be able to properly enable them with a traditional
interface (GMII or MII).
Reported-by: Romain HENRIET <romain.henriet@l-acoustics.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[cyrille.pitchen@atmel.com: backported to 4.4.y]
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f2d580b9a8149735cbc4b59c4a8df60173658140 upstream.
It turns out that preserving framebuffers after the rmfb call breaks
vmwgfx userspace. This was originally introduced because it was thought
nobody relied on the behavior, but unfortunately it seems there are
exceptions.
drm_framebuffer_remove may fail with -EINTR now, so a straight revert
is impossible. There is no way to remove the framebuffer from the lists
and active planes without introducing a race because of the different
locking requirements. Instead call drm_framebuffer_remove from a
workqueue, which is unaffected by signals.
Changes since v1:
- Add comment.
Changes since v2:
- Add fastpath for refcount = 1. (danvet)
Changes since v3:
- Rebased.
- Restore lastclose framebuffer removal too.
Fixes: 13803132818c ("drm/core: Preserve the framebuffer after removing it.")
Testcase: kms_rmfb_basic
References: https://lists.freedesktop.org/archives/dri-devel/2016-March/102876.html
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Thomas Hellstrom <thellstrom@vmware.com> #v3
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/6c63ca37-0e7e-ac7f-a6d2-c7822e3d611f@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6dc5df71ee5c8b44607928bfe27be50314dcf848 upstream.
Fix undefined reference issue reported by kbuild test robot.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5edf673d07fdcb6498be24914f3f38f8d8843199 upstream.
When a dual-edge irq is triggered, an incorrect irq will be reported on
condition that the external signal is not stable and this incorrect irq
has been registered.
Correct the register offset.
Signed-off-by: Hongkun Cao <hongkun.cao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ab6a11a7c8ef47f996974dd3c648c2c0b1a36ab1 upstream.
The ccp-crypto module for AES XTS support has a bug that can allow requests
greater than 4096 bytes in size to be passed to the CCP hardware. The CCP
hardware does not support request sizes larger than 4096, resulting in
incorrect output. The request should actually be handled by the fallback
mechanism instantiated by the ccp-crypto module.
Add a check to insure the request size is less than or equal to the maximum
supported size and use the fallback mechanism if it is not.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b66b2a0adf0e48973b582e055758b9907a7eee7c upstream.
The bcm_kona_gpio_reset() calls bcm_kona_gpio_write_lock_regs()
with what looks like the wrong parameter. The write_lock_regs
function takes a pointer to the registers, not the bcm_kona_gpio
structure.
Fix the warning, and probably bug by changing the function to
pass reg_base instead of kona_gpio, fixing the following warning:
drivers/gpio/gpio-bcm-kona.c:550:47: warning: incorrect type in argument 1
(different address spaces)
expected void [noderef] <asn:2>*reg_base
got struct bcm_kona_gpio *kona_gpio
warning: incorrect type in argument 1 (different address spaces)
expected void [noderef] <asn:2>*reg_base
got struct bcm_kona_gpio *kona_gpio
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7e059158d57b79159eaf1f504825d19866ef2c42 ]
Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets. 4.3 introduced netdevs corresponding
to tunnel vports. These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated. The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.
Instead, set the MTU on openvswitch-created netdevs to be the relevant
maximum (i.e. the maximum IP packet size minus any relevant overhead),
effectively restoring the behaviour prior to 4.3.
Signed-off-by: David Wragg <david@weave.works>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 55e5bfb53cff286c1c1ff49f51325dc15c7fea63 ]
Allow the MTU of geneve devices to be set to large values, in order to
exploit underlying networks with larger frame sizes.
GENEVE does not have a fixed encapsulation overhead (an openvswitch
rule can add variable length options), so there is no relevant maximum
MTU to enforce. A maximum of IP_MAX_MTU is used instead.
Encapsulated packets that are too big for the underlying network will
get dropped on the floor.
Signed-off-by: David Wragg <david@weave.works>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 72564b59ffc438ea103b0727a921aaddce766728 ]
Allow the MTU of vxlan devices without an underlying device to be set
to larger values (up to a maximum based on IP packet limits and vxlan
overhead).
Previously, their MTUs could not be set to higher than the
conventional ethernet value of 1500. This is a very arbitrary value
in the context of vxlan, and prevented vxlan devices from being able
to take advantage of jumbo frames etc.
The default MTU remains 1500, for compatibility.
Signed-off-by: David Wragg <david@weave.works>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ce577668a426c6a9e2470a09dcd07fbd6e45272a ]
When create a new vxlan link, example:
ip link add vtap mtu 1440 type vxlan vni 1 dev eth0
The argument "mtu" has no effect, because it is not set to conf->mtu. The
default value is used in vxlan_dev_configure function.
This problem was introduced by commit 0dfbdf4102b9 (vxlan: Factor out device
configuration).
Fixes: 0dfbdf4102b9 (vxlan: Factor out device configuration)
Signed-off-by: Chen Haiquan <oc@yunify.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f6988cb63a4e698d8a62a1d085d263d1fcc351ea ]
The team_device_event() notifier calls team_compute_features() to fix
vlan_features under team->lock to protect team->port_list. The problem is
that subsequent __team_compute_features() calls netdev_change_features()
to propagate vlan_features to upper vlan devices while team->lock is still
taken. This can lead to deadlock when NETIF_F_LRO is modified on lower
devices or team device itself.
Example:
The team0 as active backup with eth0 and eth1 NICs. Both eth0 & eth1 are
LRO capable and LRO is enabled. Thus LRO is also enabled on team0.
The command 'ethtool -K team0 lro off' now hangs due to this deadlock:
dev_ethtool()
-> ethtool_set_features()
-> __netdev_update_features(team)
-> netdev_sync_lower_features()
-> netdev_update_features(lower_1)
-> __netdev_update_features(lower_1)
-> netdev_features_change(lower_1)
-> call_netdevice_notifiers(...)
-> team_device_event(lower_1)
-> team_compute_features(team) [TAKES team->lock]
-> netdev_change_features(team)
-> __netdev_update_features(team)
-> netdev_sync_lower_features()
-> netdev_update_features(lower_2)
-> __netdev_update_features(lower_2)
-> netdev_features_change(lower_2)
-> call_netdevice_notifiers(...)
-> team_device_event(lower_2)
-> team_compute_features(team) [DEADLOCK]
The bug is present in team from the beginning but it appeared after the commit
fd867d5 (net/core: generic support for disabling netdev features down stack)
that adds synchronization of features with lower devices.
Fixes: fd867d5 (net/core: generic support for disabling netdev features down stack)
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c0795bf64cba4d1b796fdc5b74b33772841ed1bb ]
Otherwise, if we fail to allocate new PIO buffers, our TXQs will try to
use the old ones, which aren't there any more.
Fixes: 183233bec810 "sfc: Allocate and link PIO buffers; map them with write-combining"
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e5aed006be918af163eb397e45aa5ea6cefd5e01 ]
In case we find a socket with encapsulation enabled we should call
the encap_recv function even if just a udp header without payload is
available. The callbacks are responsible for correctly verifying and
dropping the packets.
Also, in case the header validation fails for geneve and vxlan we
shouldn't put the skb back into the socket queue, no one will pick
them up there. Instead we can simply discard them in the respective
encap_recv functions.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit addf8fc4acb1cf79492ac64966f07178793cb3d7 ]
We used to check dev->reg_state against NETREG_REGISTERED after each
time we are woke up. But after commit 9e641bdcfa4e ("net-tun:
restructure tun_do_read for better sleep/wakeup efficiency"), it uses
skb_recv_datagram() which does not check dev->reg_state. This will
result if we delete a tun/tap device after a process is blocked in the
reading. The device will wait for the reference count which was held
by that process for ever.
Fixes this by using RCV_SHUTDOWN which will be checked during
sk_recv_datagram() before trying to wake up the process during uninit.
Fixes: 9e641bdcfa4e ("net-tun: restructure tun_do_read for better
sleep/wakeup efficiency")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Xi Wang <xii@google.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit da4ed55165d41b1073f9a476f1c18493e9bf8c8e ]
The problem is that fib_info->nh is [0] so the struct fib_info
allocation size depends on number of nexthops. If we just copy fib_info,
we do not copy the nexthops info and driver accesses memory which is not
ours.
Given the fact that fib4 does not defer operations and therefore it does
not need copy, just pass the pointer down to drivers as it was done
before.
Fixes: 850d0cbc91 ("switchdev: remove pointers from switchdev objects")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fbd83006e3e536fcb103228d2422ea63129ccb03 upstream.
Linux fails to boot as a guest with a QEMU CD-ROM:
[ 4.439488] ata2.00: ATAPI: QEMU CD-ROM, 0.8.2, max UDMA/100
[ 4.443649] ata2.00: configured for MWDMA2
[ 4.450267] scsi 1:0:0:0: CD-ROM QEMU QEMU CD-ROM 0.8. PQ: 0 ANSI: 5
[ 4.464317] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 4.464319] ata2.00: BMDMA stat 0x5
[ 4.464339] ata2.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 0 dma 16640 in
[ 4.464339] Inquiry 12 01 00 00 ff 00res 48/20:02:00:24:00/00:00:00:00:00/a0 Emask 0x2 (HSM violation)
[ 4.464341] ata2.00: status: { DRDY DRQ }
[ 4.465864] ata2: soft resetting link
[ 4.625971] ata2.00: configured for MWDMA2
[ 4.628290] ata2: EH complete
[ 4.646670] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 4.646671] ata2.00: BMDMA stat 0x5
[ 4.646683] ata2.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 0 dma 16640 in
[ 4.646683] Inquiry 12 01 00 00 ff 00res 48/20:02:00:24:00/00:00:00:00:00/a0 Emask 0x2 (HSM violation)
[ 4.646685] ata2.00: status: { DRDY DRQ }
[ 4.648193] ata2: soft resetting link
...
Fix this by suppressing VPD inquiry for this device.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Reported-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a621bac3044ed6f7ec5fa0326491b2d4838bfa93 upstream.
When SCSI was written, all commands coming from the filesystem
(REQ_TYPE_FS commands) had data. This meant that our signal for needing
to complete the command was the number of bytes completed being equal to
the number of bytes in the request. Unfortunately, with the advent of
flush barriers, we can now get zero length REQ_TYPE_FS commands, which
confuse this logic because they satisfy the condition every time. This
means they never get retried even for retryable conditions, like UNIT
ATTENTION because we complete them early assuming they're done. Fix
this by special casing the early completion condition to recognise zero
length commands with errors and let them drop through to the retry code.
Reported-by: Sebastian Parschauer <s.parschauer@gmx.de>
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Tested-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a17fb329da68cb00558721aff876a80bba2fdb9 upstream.
Grygorii Strashko reports:
The PM runtime will be left disabled for the device if its
.suspend_late() callback fails and async suspend is not allowed
for this device. In this case device will not be added in
dpm_late_early_list and dpm_resume_early() will ignore this
device, as result PM runtime will be disabled for it forever
(side effect: after 8 subsequent failures for the same device
the PM runtime will be reenabled due to disable_depth overflow).
To fix this problem, add devices to dpm_late_early_list regardless
of whether or not device_suspend_late() returns errors for them.
That will ensure failures in there to be handled consistently for
all devices regardless of their async suspend/resume status.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 310944d148e3600dcff8b346bee7fa01d34903b1 upstream.
The component master driver imx-drm-core matches component devices using
their of_node. Since commit 950b410dd1ab ("gpu: ipu-v3: Fix imx-ipuv3-crtc
module autoloading"), the imx-ipuv3-crtc dev->of_node is not set during
probing. Before that, of_node was set and caused an of: modalias to be
used instead of the platform: modalias, which broke module autoloading.
On the other hand, if dev->of_node is not set yet when the imx-ipuv3-crtc
probe function calls component_add, component matching in imx-drm-core
fails. While dev->of_node will be set once the next component tries to
bring up the component master, imx-drm-core component binding will never
succeed if one of the crtc devices is probed last.
Add of_node to the component platform data and match against the
pdata->of_node instead of dev->of_node in imx-drm-core to work around
this problem.
Fixes: 950b410dd1ab ("gpu: ipu-v3: Fix imx-ipuv3-crtc module autoloading")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7045c3689f148a0c95f42bae8ef3eb2829ac7de9 upstream.
When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.
Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.
Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 243e6a44b9ca ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 15606534bf0a65d8a74a90fd57b8712d147dbca6)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unfortunately since we don't have Dave's connector refcounting patch
here yet, it's very possible that drm_atomic_state_default_clear() could
get called by intel_display_resume() when
intel_dp_mst_destroy_connector() isn't completely finished destroying an
mst connector, but has already finished setting connector->funcs to
NULL. As such, we need to treat the connector like it's already been
destroyed and just skip it, otherwise we'll end up dereferencing a NULL
pointer.
This fix is only required for 4.6 and below. David Airlie's patchseries
for 4.7 to add connector reference counting provides a more proper fix
for this.
Changes since v1:
- Fix leftover whitespace
Upstream fix: 0552f7651bc2 ("drm/i915/mst: use reference counted
connectors. (v3)")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
|
|
commit 255f0e7c418ad95a4baeda017ae6182ba9b3c423 upstream.
During boot, MST hotplugs are generally expected (even if no physical
hotplugging occurs) and result in DRM's connector topology changing.
This means that using num_connector from the current mode configuration
can lead to the number of connectors changing under us. This can lead to
some nasty scenarios in fbcon:
- We allocate an array to the size of dev->mode_config.num_connectors.
- MST hotplug occurs, dev->mode_config.num_connectors gets incremented.
- We try to loop through each element in the array using the new value
of dev->mode_config.num_connectors, and end up going out of bounds
since dev->mode_config.num_connectors is now larger then the array we
allocated.
fb_helper->connector_count however, will always remain consistent while
we do a modeset in fb_helper.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Clarify why we need this. Also remove the now unused "dev"
local variable to appease gcc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-3-git-send-email-cpaul@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 14a3842a1d5945067d1dd0788f314e14d5b18e5b upstream.
During boot time, MST devices usually send a ton of hotplug events
irregardless of whether or not any physical hotplugs actually occurred.
Hotplugs mean connectors being created/destroyed, and the number of DRM
connectors changing under us. This isn't a problem if we use
fb_helper->connector_count since we only set it once in the code,
however if we use num_connector from struct drm_mode_config we risk it's
value changing under us. On top of that, there's even a chance that
dev->mode_config.num_connector != fb_helper->connector_count. If the
number of connectors happens to increase under us, we'll end up using
the wrong array size for memcpy and start writing beyond the actual
length of the array, occasionally resulting in kernel panics.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Clarify why we need this.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-2-git-send-email-cpaul@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9d746ab68163d642dae13756b2b3145b2e38cb65 upstream.
When porting the hdmi deep color detection code from
radeon-kms to amdgpu-kms apparently some kind of
copy and paste error happened, attaching an else
branch to the wrong if statement.
The result is that hdmi deep color mode is always
disabled, regardless of gpu and display capabilities and
user wishes, as the code mistakenly thinks that the display
doesn't provide the required max_tmds_clock limit and falls
back to 8 bpc.
This patch fixes deep color support, as tested on a
R9 380 Tonga Pro + suitable display, and should be
backported to all kernels with amdgpu-kms support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6b8812eb004ee2b24aac8b1a711a0e8e797df3ce upstream.
This is a port of radeon commit:
3d2d98ee1af0cf6eebfbd6bff4c17d3601ac1284
drm/radeon: use drm_mode_vrefresh() rather than mode->vrefresh
to amdgpu.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7851496a32319237456919575e5f4ba62f74cc7d upstream.
mode->hdisplay * (var->bits_per_pixel + 7) gets evaluated before
the division, potentially making the pitch larger than it should
be.
Since the original intention is to do a div-round-up, just use
the macro instead.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e02e58843153ce80a9fe7588def89b2638d40e64 upstream.
Instead of calling vmw_cmd_ok, call vmw_cmd_dx_cid_check to
validate the context id for query commands.
Signed-off-by: Charmaine Lee <charmainel@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1883598d4201361a6d2ce785095695f58071ee11 upstream.
Fixes piglit tests nv_conditional_render-* crashes.
Signed-off-by: Charmaine Lee <charmainel@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7ccca1d5bf69fdd1d3c5fcf84faf1659a6e0ad11 upstream.
Fix possible out of bounds read, by adding missing comma.
The code may read pass the end of the dsi_errors array
when the most significant bit (bit #31) in the intr_stat register
is set.
This bug has been detected using CppCheck (static analysis tool).
Signed-off-by: Itai Handler <itai_handler@hotmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f0f393877c71ad227d36705d61d1e4062bc29cf5 upstream.
Commit ff1e22e7a638 ("xen/events: Mask a moving irq") open-coded
irq_move_irq() but left out checking if the IRQ is disabled. This broke
resuming from suspend since it tries to move a (disabled) irq without
holding the IRQ's desc->lock. Fix it by adding in a check for disabled
IRQs.
The resulting stacktrace was:
kernel BUG at /build/linux-UbQGH5/linux-4.4.0/kernel/irq/migration.c:31!
invalid opcode: 0000 [#1] SMP
Modules linked in: xenfs xen_privcmd ...
CPU: 0 PID: 9 Comm: migration/0 Not tainted 4.4.0-22-generic #39-Ubuntu
Hardware name: Xen HVM domU, BIOS 4.6.1-xs125180 05/04/2016
task: ffff88003d75ee00 ti: ffff88003d7bc000 task.ti: ffff88003d7bc000
RIP: 0010:[<ffffffff810e26e2>] [<ffffffff810e26e2>] irq_move_masked_irq+0xd2/0xe0
RSP: 0018:ffff88003d7bfc50 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff88003d40ba00 RCX: 0000000000000001
RDX: 0000000000000001 RSI: 0000000000000100 RDI: ffff88003d40bad8
RBP: ffff88003d7bfc68 R08: 0000000000000000 R09: ffff88003d000000
R10: 0000000000000000 R11: 000000000000023c R12: ffff88003d40bad0
R13: ffffffff81f3a4a0 R14: 0000000000000010 R15: 00000000ffffffff
FS: 0000000000000000(0000) GS:ffff88003da00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd4264de624 CR3: 0000000037922000 CR4: 00000000003406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Stack:
ffff88003d40ba38 0000000000000024 0000000000000000 ffff88003d7bfca0
ffffffff814c8d92 00000010813ef89d 00000000805ea732 0000000000000009
0000000000000024 ffff88003cc39b80 ffff88003d7bfce0 ffffffff814c8f66
Call Trace:
[<ffffffff814c8d92>] eoi_pirq+0xb2/0xf0
[<ffffffff814c8f66>] __startup_pirq+0xe6/0x150
[<ffffffff814ca659>] xen_irq_resume+0x319/0x360
[<ffffffff814c7e75>] xen_suspend+0xb5/0x180
[<ffffffff81120155>] multi_cpu_stop+0xb5/0xe0
[<ffffffff811200a0>] ? cpu_stop_queue_work+0x80/0x80
[<ffffffff811203d0>] cpu_stopper_thread+0xb0/0x140
[<ffffffff810a94e6>] ? finish_task_switch+0x76/0x220
[<ffffffff810ca731>] ? __raw_callee_save___pv_queued_spin_unlock+0x11/0x20
[<ffffffff810a3935>] smpboot_thread_fn+0x105/0x160
[<ffffffff810a3830>] ? sort_range+0x30/0x30
[<ffffffff810a0588>] kthread+0xd8/0xf0
[<ffffffff810a04b0>] ? kthread_create_on_node+0x1e0/0x1e0
[<ffffffff8182568f>] ret_from_fork+0x3f/0x70
[<ffffffff810a04b0>] ? kthread_create_on_node+0x1e0/0x1e0
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 11ca2b7ab432eb90906168c327733575e68d388f upstream.
New bindings use "fsl,t1040-ucc-uart" as the compatible for qe-uart.
So add it.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit baf43c6eace43868e490f18560287fa3481b2159 upstream.
In v4l2-compliance utility, test VIDIOC_CREATE_BUFS will check whether reserved
filed of v4l2_create_buffers filled with zero
Reserved field is filled with zero in v4l_create_bufs.
This patch copy reserved field of v4l2_create_buffer from kernel space to user
space
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
