summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2013-06-13USB: option: blacklist network interface on Huawei E1820Bjørn Mork
commit b8a24e6281d37243c06b9497dcbfaa98c1e2ad35 upstream. The mode used by Windows for the Huawei E1820 will use the same ff/ff/ff class codes for both serial and network functions. Reported-by: Graham Inggs <graham.inggs@uct.ac.za> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07thinkpad-acpi: recognize latest V-Series using DMI_BIOS_VENDORManoj Iyer
commit a4f46bb9fa84642e356898ee44b670989622f8bb upstream. In the latest V-series bios DMI_PRODUCT_VERSION does not contain the string Lenovo or Thinkpad, but is set to the model number, this causes the thinkpad_acpi module to fail to load. Recognize laptop as Lenovo using DMI_BIOS_VENDOR instead, which is set to Lenovo. Test on V490u ============= == After the patch == [ 1350.295757] thinkpad_acpi: ThinkPad ACPI Extras v0.24 [ 1350.295760] thinkpad_acpi: http://ibm-acpi.sf.net/ [ 1350.295761] thinkpad_acpi: ThinkPad BIOS H7ET21WW (1.00 ), EC unknown [ 1350.295763] thinkpad_acpi: Lenovo LENOVO, model LV5DXXX [ 1350.296086] thinkpad_acpi: detected a 8-level brightness capable ThinkPad [ 1350.296694] thinkpad_acpi: radio switch found; radios are enabled [ 1350.296703] thinkpad_acpi: possible tablet mode switch found; ThinkPad in laptop mode [ 1350.306466] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked [ 1350.307082] Registered led device: tpacpi::thinklight [ 1350.307215] Registered led device: tpacpi::power [ 1350.307255] Registered led device: tpacpi::standby [ 1350.307294] Registered led device: tpacpi::thinkvantage [ 1350.308160] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one [ 1350.308333] thinkpad_acpi: Console audio control enabled, mode: monitor (read only) [ 1350.312287] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input14 == Before the patch == sudo modprobe thinkpad_acpi FATAL: Error inserting thinkpad_acpi (/lib/modules/3.2.0-27-generic/kernel/drivers/platform/x86/thinkpad_acpi.ko): No such device Test on B485 ============= This patch was also test in a B485 where the thinkpad_acpi module does not have any issues loading. But, I tested it to make sure this patch does not break on already functioning models of Lenovo products. [13486.746359] thinkpad_acpi: ThinkPad ACPI Extras v0.24 [13486.746364] thinkpad_acpi: http://ibm-acpi.sf.net/ [13486.746368] thinkpad_acpi: ThinkPad BIOS HJET15WW(1.01), EC unknown [13486.746373] thinkpad_acpi: Lenovo Lenovo LB485, model 814TR01 [13486.747300] thinkpad_acpi: detected a 8-level brightness capable ThinkPad [13486.752435] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked [13486.752883] Registered led device: tpacpi::thinklight [13486.752915] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one [13486.753216] thinkpad_acpi: Console audio control enabled, mode: monitor (read only) [13486.757147] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input15 Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: Shuduo Sang <shuduo.sang@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07iommu/amd: Workaround for ERBT1312Joerg Roedel
commit d3263bc29706e42f74d8800807c2dedf320d77f1 upstream. Work around an IOMMU hardware bug where clearing the EVT_INT or PPR_INT bit in the status register may race with the hardware trying to set it again. When not handled the bit might not be cleared and we lose all future event or ppr interrupts. Reported-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Signed-off-by: Joerg Roedel <joro@8bytes.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07iommu/amd: Re-enable IOMMU event log interrupt after handling.Suravee Suthikulpanit
commit 925fe08bce38d1ff052fe2209b9e2b8d5fbb7f98 upstream. Current driver does not clear the IOMMU event log interrupt bit in the IOMMU status register after processing an interrupt. This causes the IOMMU hardware to generate event log interrupt only once. This has been observed in both IOMMU v1 and V2 hardware. This patch clears the bit by writing 1 to bit 1 of the IOMMU status register (MMIO Offset 2020h) Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Signed-off-by: Joerg Roedel <joro@8bytes.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07xen-netback: remove skb in xen_netbk_alloc_pageWei Liu
commit 27f852282ab9a028f57da96d05c26f38c424a315 upstream. This variable is never used. Signed-off-by: Wei Liu <wei.liu2@citrix.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07xen/events: Handle VIRQ_TIMER before any other hardirq in event loop.Keir Fraser
commit bee980d9e9642e96351fa3ca9077b853ecf62f57 upstream. This avoids any other hardirq handler seeing a very stale jiffies value immediately after wakeup from a long idle period. The one observable symptom of this was a USB keyboard, with software keyboard repeat, which would always repeat a key immediately that it was pressed. This is due to the key press waking the guest, the key handler immediately runs, sees an old jiffies value, and then that jiffies value significantly updated, before the key is unpressed. Reviewed-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Keir Fraser <keir.fraser@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07libata: make ata_exec_internal_sg honor DMADIRVincent Pelletier
commit e771451c0a831d96a7c14b0ca8a8ec671d98567b upstream. libata honors DMADIR for regular commands, but not for internal commands used (among other) during device initialisation. This makes SATA-host-to-PATA-device bridges based on Silicon Image SiL3611 (such as "Abit Serillel 2") end up disabled when used with an ATAPI device after a few tries. Log output of the bridge being hot-plugged with an ATAPI drive: [ 9631.212901] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen [ 9631.212913] ata1: irq_stat 0x00000040, connection status changed [ 9631.212923] ata1: SError: { CommWake 10B8B DevExch } [ 9631.212939] ata1: hard resetting link [ 9632.104962] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 9632.106393] ata1.00: ATAPI: PIONEER DVD-RW DVR-115, 1.06, max UDMA/33 [ 9632.106407] ata1.00: applying bridge limits [ 9632.108151] ata1.00: configured for UDMA/33 [ 9637.105303] ata1.00: qc timeout (cmd 0xa0) [ 9637.105324] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5) [ 9637.105335] ata1: hard resetting link [ 9638.044599] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 9638.047878] ata1.00: configured for UDMA/33 [ 9643.044933] ata1.00: qc timeout (cmd 0xa0) [ 9643.044953] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5) [ 9643.044963] ata1: limiting SATA link speed to 1.5 Gbps [ 9643.044971] ata1.00: limiting speed to UDMA/33:PIO3 [ 9643.044979] ata1: hard resetting link [ 9643.984225] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 9643.987471] ata1.00: configured for UDMA/33 [ 9648.984591] ata1.00: qc timeout (cmd 0xa0) [ 9648.984612] ata1.00: failed to clear UNIT ATTENTION (err_mask=0x5) [ 9648.984619] ata1.00: disabled [ 9649.000593] ata1: hard resetting link [ 9649.939902] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 9649.955864] ata1: EH complete With this patch, the drive enumerates correctly when libata is loaded with atapi_dmadir=1: [ 9891.810863] ata1: exception Emask 0x10 SAct 0x0 SErr 0x40c0000 action 0xe frozen [ 9891.810874] ata1: irq_stat 0x00000040, connection status changed [ 9891.810884] ata1: SError: { CommWake 10B8B DevExch } [ 9891.810900] ata1: hard resetting link [ 9892.762105] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 9892.763544] ata1.00: ATAPI: PIONEER DVD-RW DVR-115, 1.06, max UDMA/33, DMADIR [ 9892.763558] ata1.00: applying bridge limits [ 9892.765393] ata1.00: configured for UDMA/33 [ 9892.786063] ata1: EH complete [ 9892.792062] scsi 0:0:0:0: CD-ROM PIONEER DVD-RW DVR-115 1.06 PQ: 0 ANSI: 5 [ 9892.798455] sr2: scsi3-mmc drive: 12x/12x writer dvd-ram cd/rw xa/form2 cdda tray [ 9892.798837] sr 0:0:0:0: Attached scsi CD-ROM sr2 [ 9892.799109] sr 0:0:0:0: Attached scsi generic sg6 type 5 Based on a patch by Csaba Halász <csaba.halasz@gmail.com> on linux-ide: http://marc.info/?l=linux-ide&m=136121147832295&w=2 tj: minor formatting changes. Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07ata_piix: add PCI IDs for Intel BayTailChew, Chiau Ee
commit fca8c90d519dedd4f4b19901d005c243f7f0bf2e upstream. Adds IDE-mode SATA Device IDs for the Intel BayTrail platform. Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07USB: io_ti: Fix NULL dereference in chase_port()Wolfgang Frisch
commit 1ee0a224bc9aad1de496c795f96bc6ba2c394811 upstream. The tty is NULL when the port is hanging up. chase_port() needs to check for this. This patch is intended for stable series. The behavior was observed and tested in Linux 3.2 and 3.7.1. Johan Hovold submitted a more elaborate patch for the mainline kernel. [ 56.277883] usb 1-1: edge_bulk_in_callback - nonzero read bulk status received: -84 [ 56.278811] usb 1-1: USB disconnect, device number 3 [ 56.278856] usb 1-1: edge_bulk_in_callback - stopping read! [ 56.279562] BUG: unable to handle kernel NULL pointer dereference at 00000000000001c8 [ 56.280536] IP: [<ffffffff8144e62a>] _raw_spin_lock_irqsave+0x19/0x35 [ 56.281212] PGD 1dc1b067 PUD 1e0f7067 PMD 0 [ 56.282085] Oops: 0002 [#1] SMP [ 56.282744] Modules linked in: [ 56.283512] CPU 1 [ 56.283512] Pid: 25, comm: khubd Not tainted 3.7.1 #1 innotek GmbH VirtualBox/VirtualBox [ 56.283512] RIP: 0010:[<ffffffff8144e62a>] [<ffffffff8144e62a>] _raw_spin_lock_irqsave+0x19/0x35 [ 56.283512] RSP: 0018:ffff88001fa99ab0 EFLAGS: 00010046 [ 56.283512] RAX: 0000000000000046 RBX: 00000000000001c8 RCX: 0000000000640064 [ 56.283512] RDX: 0000000000010000 RSI: ffff88001fa99b20 RDI: 00000000000001c8 [ 56.283512] RBP: ffff88001fa99b20 R08: 0000000000000000 R09: 0000000000000000 [ 56.283512] R10: 0000000000000000 R11: ffffffff812fcb4c R12: ffff88001ddf53c0 [ 56.283512] R13: 0000000000000000 R14: 00000000000001c8 R15: ffff88001e19b9f4 [ 56.283512] FS: 0000000000000000(0000) GS:ffff88001fd00000(0000) knlGS:0000000000000000 [ 56.283512] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 56.283512] CR2: 00000000000001c8 CR3: 000000001dc51000 CR4: 00000000000006e0 [ 56.283512] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 56.283512] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 56.283512] Process khubd (pid: 25, threadinfo ffff88001fa98000, task ffff88001fa94f80) [ 56.283512] Stack: [ 56.283512] 0000000000000046 00000000000001c8 ffffffff810578ec ffffffff812fcb4c [ 56.283512] ffff88001e19b980 0000000000002710 ffffffff812ffe81 0000000000000001 [ 56.283512] ffff88001fa94f80 0000000000000202 ffffffff00000001 0000000000000296 [ 56.283512] Call Trace: [ 56.283512] [<ffffffff810578ec>] ? add_wait_queue+0x12/0x3c [ 56.283512] [<ffffffff812fcb4c>] ? usb_serial_port_work+0x28/0x28 [ 56.283512] [<ffffffff812ffe81>] ? chase_port+0x84/0x2d6 [ 56.283512] [<ffffffff81063f27>] ? try_to_wake_up+0x199/0x199 [ 56.283512] [<ffffffff81263a5c>] ? tty_ldisc_hangup+0x222/0x298 [ 56.283512] [<ffffffff81300171>] ? edge_close+0x64/0x129 [ 56.283512] [<ffffffff810612f7>] ? __wake_up+0x35/0x46 [ 56.283512] [<ffffffff8106135b>] ? should_resched+0x5/0x23 [ 56.283512] [<ffffffff81264916>] ? tty_port_shutdown+0x39/0x44 [ 56.283512] [<ffffffff812fcb4c>] ? usb_serial_port_work+0x28/0x28 [ 56.283512] [<ffffffff8125d38c>] ? __tty_hangup+0x307/0x351 [ 56.283512] [<ffffffff812e6ddc>] ? usb_hcd_flush_endpoint+0xde/0xed [ 56.283512] [<ffffffff8144e625>] ? _raw_spin_lock_irqsave+0x14/0x35 [ 56.283512] [<ffffffff812fd361>] ? usb_serial_disconnect+0x57/0xc2 [ 56.283512] [<ffffffff812ea99b>] ? usb_unbind_interface+0x5c/0x131 [ 56.283512] [<ffffffff8128d738>] ? __device_release_driver+0x7f/0xd5 [ 56.283512] [<ffffffff8128d9cd>] ? device_release_driver+0x1a/0x25 [ 56.283512] [<ffffffff8128d393>] ? bus_remove_device+0xd2/0xe7 [ 56.283512] [<ffffffff8128b7a3>] ? device_del+0x119/0x167 [ 56.283512] [<ffffffff812e8d9d>] ? usb_disable_device+0x6a/0x180 [ 56.283512] [<ffffffff812e2ae0>] ? usb_disconnect+0x81/0xe6 [ 56.283512] [<ffffffff812e4435>] ? hub_thread+0x577/0xe82 [ 56.283512] [<ffffffff8144daa7>] ? __schedule+0x490/0x4be [ 56.283512] [<ffffffff8105798f>] ? abort_exclusive_wait+0x79/0x79 [ 56.283512] [<ffffffff812e3ebe>] ? usb_remote_wakeup+0x2f/0x2f [ 56.283512] [<ffffffff812e3ebe>] ? usb_remote_wakeup+0x2f/0x2f [ 56.283512] [<ffffffff810570b4>] ? kthread+0x81/0x89 [ 56.283512] [<ffffffff81057033>] ? __kthread_parkme+0x5c/0x5c [ 56.283512] [<ffffffff8145387c>] ? ret_from_fork+0x7c/0xb0 [ 56.283512] [<ffffffff81057033>] ? __kthread_parkme+0x5c/0x5c [ 56.283512] Code: 8b 7c 24 08 e8 17 0b c3 ff 48 8b 04 24 48 83 c4 10 c3 53 48 89 fb 41 50 e8 e0 0a c3 ff 48 89 04 24 e8 e7 0a c3 ff ba 00 00 01 00 <f0> 0f c1 13 48 8b 04 24 89 d1 c1 ea 10 66 39 d1 74 07 f3 90 66 [ 56.283512] RIP [<ffffffff8144e62a>] _raw_spin_lock_irqsave+0x19/0x35 [ 56.283512] RSP <ffff88001fa99ab0> [ 56.283512] CR2: 00000000000001c8 [ 56.283512] ---[ end trace 49714df27e1679ce ]--- Signed-off-by: Wolfgang Frisch <wfpub@roembden.net> Cc: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07drm/radeon: fix card_posted check for newer asicsAlex Deucher
commit 09fb8bd1a63b0f9f15e655c4fe8d047e5d2bf67a upstream. Newer asics have variable numbers of crtcs. Use that rather than the asic family to determine which crtcs to check. This avoids checking non-existent crtcs or missing crtcs on certain asics. Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07iscsi-target: fix heap buffer overflow on errorKees Cook
commit cea4dcfdad926a27a18e188720efe0f2c9403456 upstream. If a key was larger than 64 bytes, as checked by iscsi_check_key(), the error response packet, generated by iscsi_add_notunderstood_response(), would still attempt to copy the entire key into the packet, overflowing the structure on the heap. Remote preauthentication kernel memory corruption was possible if a target was configured and listening on the network. CVE-2013-2850 Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07drivers/block/brd.c: fix brd_lookup_page() raceBrian Behlendorf
commit dfd20b2b174d3a9b258ea3b7a35ead33576587b1 upstream. The index on the page must be set before it is inserted in the radix tree. Otherwise there is a small race which can occur during lookup where the page can be found with the incorrect index. This will trigger the BUG_ON() in brd_lookup_page(). Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Reported-by: Chris Wedgwood <cw@f00f.org> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07drivers/leds/leds-ot200.c: fix error caused by shifted maskChristian Gmeiner
commit 4b949b8af12e24b8a48fa5bb775a13b558d9f4da upstream. During the development of this driver an in-house register documentation was used. The last week some integration tests were done and this problem was found. It turned out that the released register documentation is wrong. The fix is very simple: shift all masks by one. Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Bryan Wu <cooloney@gmail.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07USB: UHCI: fix for suspend of virtual HP controllerAlan Stern
commit 997ff893603c6455da4c5e26ba1d0f81adfecdfc upstream. HP's virtual UHCI host controller takes a long time to suspend (several hundred microseconds), even when no devices are attached. This provokes a warning message from uhci-hcd in the auto-stop case. To prevent this from happening, this patch adds a test to avoid performing an auto-stop when the wait_for_hp quirk flag is set. The controller will still suspend through the normal runtime PM mechanism. And since that pathway includes a 1-ms delay, the slowness of the virtual hardware won't matter. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: ZhenHua <zhen-hual@hp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07USB: xHCI: override bogus bulk wMaxPacketSize valuesAlan Stern
commit e4f47e3675e6f1f40906b785b934ce963e9f2eb3 upstream. This patch shortens the logic in xhci_endpoint_init() by moving common calculations involving max_packet and max_burst outside the switch statement, rather than repeating the same code in multiple case-specific statements. It also replaces two usages of max_packet which were clearly intended to be max_burst all along. More importantly, it compensates for a common bug in high-speed bulk endpoint descriptors. In many devices there is a bulk endpoint having a wMaxPacketSize value smaller than 512, which is forbidden by the USB spec. Some xHCI controllers can't handle this and refuse to accept the endpoint. This patch changes the max_packet value to 512, which allows the controller to use the endpoint properly. In practice the bogus maxpacket size doesn't matter, because none of the transfers sent via these endpoints are longer than the maxpacket value anyway. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: "Aurélien Leblond" <blablack@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07USB: reset resume quirk needed by a hubOliver Neukum
commit bac6b03275184c912ad0818c9a0a736847804dca upstream. Werner Fink has reported problems with this hub. Signed-off-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07USB: Blacklisted Cinterion's PLxx WWAN InterfaceSchemmel Hans-Christoph
commit 8ff10bdb14a52e3f25d4ce09e0582a8684c1a6db upstream. /drivers/usb/serial/option.c: Blacklisted Cinterion's PLxx WWAN Interface (USB Interface 4), because it will be handled by QMI WWAN driver. Product IDs renamed. Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07TTY: Fix tty miss restart after we turn off flow-controlWang YanQing
commit dab73b4eb9ef924a2b90dab84e539076d82b256f upstream. I meet emacs hang in start if I do the operation below: 1: echo 3 > /proc/sys/vm/drop_caches 2: emacs BigFile 3: Press CTRL-S follow 2 immediately Then emacs hang on, CTRL-Q can't resume, the terminal hang on, you can do nothing with this terminal except close it. The reason is before emacs takeover control the tty, we use CTRL-S to XOFF it. Then when emacs takeover the control, it may don't use the flow-control, so emacs hang. This patch fix it. This patch will fix a kind of strange tty relation hang problem, I believe I meet it with vim in ssh, and also see below bug report: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=465823 Signed-off-by: Wang YanQing <udknight@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07USB: cxacru: potential underflow in cxacru_cm_get_array()Dan Carpenter
commit 2a0ebf80aa95cc758d4725f74a7016e992606a39 upstream. The value of "offd" comes off the instance->rcv_buf[] and we used it as the offset into an array. The problem is that we check the upper bound but not for negative values. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07USB: ftdi_sio: Add support for Newport CONEX motor driversGomella, Andrew (NIH/NHLBI) [F]
commit 7138143972b7c293267c783fc99a194f0ceff7f2 upstream. Here are two more devices that use FTDI USB-to-serial chips with new product ID's. The devices are the Newport Conex-AGP and Conex-CC motor controllers. (http://www.newport.com/CONEX-AGP-Integrated-Piezo-Motor-Rotation-Stages-/987623/1033/info.aspx) (http://www.newport.com/CONEX-CC-DC-Servo-Controller-Actuators/934114/1033/info.aspx) usb-devices command yields: P: Vendor=104d ProdID=3002 Rev=06.00 S: Manufacturer=Newport S: Product=CONEX-CC as well as P: Vendor=104d ProdID=3006 Rev=06.00 S: Manufacturer=Newport S: Product=CONEX-AGP Signed-off-by: Andrew Gomella <andrew.gomella@nih.gov> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07USB: option: add device IDs for Dell 5804 (Novatel E371) WWAN cardDan Williams
commit 49c6e370dd6400b84897c4100095089b5c13a061 upstream. A rebranded Novatel E371 for AT&T's LTE bands. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07usb: option: Add Telewell TW-LTE 4GTeppo Kotilainen
commit 73c042df6e1bc50544842a04b777b36bbe3630e6 upstream. Information from driver description files: diag: VID_19D2&PID_0412&MI_00 nmea: VID_19D2&PID_0412&MI_01 at: VID_19D2&PID_0412&MI_02 modem: VID_19D2&PID_0412&MI_03 net: VID_19D2&PID_0412&MI_04 Signed-off-by: Teppo Kotilainen <qubit303@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-07staging: vt6656: use free_netdev instead of kfreeHema Prathaban
commit 0a438d5b381e2bdfd5e02d653bf46fcc878356e3 upstream. use free_netdev() instead of kfree(pDevice->apdev) Signed-off-by: Hema Prathaban <hemaklnce@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-24media: mantis: fix silly crash caseAlan Cox
commit e1d45ae10aea8e8a403e5d96bf5902ee670007ff upstream. If we set mantis->fe to NULL on an error its not a good idea to then try passing NULL to the unregister paths and oopsing really. Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=16473 Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Cc: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-24drm/radeon: Fix VRAM size calculation for VRAM >= 4GBNiels Ole Salscheider
commit fc986034540102cd090237bf3f70262e1ae80d9c upstream. Add ULL prefix to avoid overflow. Signed-off-by: Niels Ole Salscheider <niels_ole@salscheider-online.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-24i2c: designware: always clear interrupts before enabling themMika Westerberg
commit 2a2d95e9d6d29e726cc294b65391917ed2e32bf4 upstream. If the I2C bus is put to a low power state by an ACPI method it might pull the SDA line low (as its power is removed). Once the bus is put to full power state again, the SDA line is pulled back to high. This transition looks like a STOP condition from the controller point-of-view which sets STOP detected bit in its status register causing the driver to fail subsequent transfers. Fix this by always clearing all interrupts before we start a transfer. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-24hwmon: fix error return code in abituguru_probe()Wei Yongjun
commit ecacb0b17c08fae89f65468727f0e4b8e91da4e1 upstream. Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19drm/radeon: check incoming cliprects pointerKees Cook
commit fefaedcfb82d2e57c2320acf60604ab03b750cc0 upstream. The "boxes" parameter points into userspace memory. It should be verified like any other operation against user memory. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19ipmi: ipmi_devintf: compat_ioctl method fails to take ipmi_mutexBenjamin LaHaise
commit 6368087e851e697679af059b4247aca33a69cef3 upstream. When a 32 bit version of ipmitool is used on a 64 bit kernel, the ipmi_devintf code fails to correctly acquire ipmi_mutex. This results in incomplete data being retrieved in some cases, or other possible failures. Add a wrapper around compat_ipmi_ioctl() to take ipmi_mutex to fix this. Signed-off-by: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19drivers/char/ipmi: memcpy, need additional 2 bytes to avoid memory overflowChen Gang
commit a5f2b3d6a738e7d4180012fe7b541172f8c8dcea upstream. When calling memcpy, read_data and write_data need additional 2 bytes. write_data: for checking: "if (size > IPMI_MAX_MSG_LENGTH)" for operating: "memcpy(bt->write_data + 3, data + 1, size - 1)" read_data: for checking: "if (msg_len < 3 || msg_len > IPMI_MAX_MSG_LENGTH)" for operating: "memcpy(data + 2, bt->read_data + 4, msg_len - 2)" Signed-off-by: Chen Gang <gang.chen@asianux.com> Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19ACPI / EC: Restart transaction even when the IBF flag setLan Tianyu
commit 28fe5c825f8e15744d04c7c1b8df197950923ecd upstream. The EC driver works abnormally with IBF flag always set. IBF means "The host has written a byte of data to the command or data port, but the embedded controller has not yet read it". If IBF is set in the EC status and not cleared, this will cause all subsequent EC requests to fail with a timeout error. Change the EC driver so that it doesn't refuse to restart a transaction if IBF is set in the status. Also increase the number of transaction restarts to 5, as it turns out that 2 is not sufficient in some cases. This bug happens on several different machines (Asus V1S, Dell Latitude E6530, Samsung R719, Acer Aspire 5930G, Sony Vaio SR19VN and others). [rjw: Changelog] References: https://bugzilla.kernel.org/show_bug.cgi?id=14733 References: https://bugzilla.kernel.org/show_bug.cgi?id=15560 References: https://bugzilla.kernel.org/show_bug.cgi?id=15946 References: https://bugzilla.kernel.org/show_bug.cgi?id=42945 References: https://bugzilla.kernel.org/show_bug.cgi?id=48221 Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19iscsi-target: Fix processing of OOO commandsShlomo Pongratz
commit 3eccfdb01da58fbd0f789ae6ca61cee3769e26de upstream. Fix two issues in OOO commands processing done at iscsit_attach_ooo_cmdsn. Handle command serial numbers wrap around by using iscsi_sna_lt and not regular comparisson. The routine iterates until it finds an entry whose serial number is greater than the serial number of the new one, thus the new entry should be inserted before that entry and not after. Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19drivers/rtc/rtc-pcf2123.c: fix error return code in pcf2123_probe()Wei Yongjun
commit 35623715818dfa720cccf99cd280dcbb4b78da23 upstream. Fix to return -ENODEV in the chip not found error handling case instead of 0, as done elsewhere in this function. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Cc: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19drbd: fix for deadlock when using automatic split-brain-recoveryPhilipp Reisner
commit 7c689e63a847316c1b2500f86891b0a574ce7e69 upstream. With an automatic after split-brain recovery policy of "after-sb-1pri call-pri-lost-after-sb", when trying to drbd_set_role() to R_SECONDARY, we run into a deadlock. This was first recognized and supposedly fixed by 2009-06-10 "Fixed a deadlock when using automatic split brain recovery when both nodes are" replacing drbd_set_role() with drbd_change_state() in that code-path, but the first hunk of that patch forgets to remove the drbd_set_role(). We apparently only ever tested the "two primaries" case. Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19r8169: fix vlan tag read ordering.Francois Romieu
commit ce11ff5e5963e441feb591e76278528f876c332d upstream. Control of receive descriptor must not be returned to ethernet chipset before vlan tag processing is done. VLAN tag receive word is now reset both in normal and error path. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Spotted-by: Timo Teras <timo.teras@iki.fi> Cc: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19pch_dma: Use GFP_ATOMIC because called from interrupt contextTomoya MORINAGA
commit 5c1ef59168c485318e40ba485c1eba57d81d0faa upstream. pdc_desc_get() is called from pd_prep_slave_sg, and the function is called from interrupt context(e.g. Uart driver "pch_uart.c"). In fact, I saw kernel error message. So, GFP_ATOMIC must be used not GFP_NOIO. Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19dm thin: do not set discard_zeroes_dataMike Snitzer
commit 307615a26e95406c42c95916a66ba50434567e0f upstream. The dm thin pool target claims to support the zeroing of discarded data areas. This turns out to be incorrect when processing discards that do not exactly cover a complete number of blocks, so the target must always set discard_zeroes_data_unsupported. The thin pool target will zero blocks when they are allocated if the skip_block_zeroing feature is not specified. The block layer may send a discard that only partly covers a block. If a thin pool block is partially discarded then there is no guarantee that the discarded data will get zeroed before it is accessed again. Due to this, thin devices cannot claim discards will always zero data. Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Cc: Libo Chen <libo.chen@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19macvlan: fix passthru mode race between dev removal and rx pathJiri Pirko
[ Upstream commit 233c7df0821c4190e2d3f4be0f2ca0ab40a5ed8c, note that I had to add list_first_or_null_rcu to rculist.h in order to accomodate this fix. ] Currently, if macvlan in passthru mode is created and data are rxed and you remove this device, following panic happens: NULL pointer dereference at 0000000000000198 IP: [<ffffffffa0196058>] macvlan_handle_frame+0x153/0x1f7 [macvlan] I'm using following script to trigger this: <script> while [ 1 ] do ip link add link e1 name macvtap0 type macvtap mode passthru ip link set e1 up ip link set macvtap0 up IFINDEX=`ip link |grep macvtap0 | cut -f 1 -d ':'` cat /dev/tap$IFINDEX >/dev/null & ip link del dev macvtap0 done </script> I run this script while "ping -f" is running on another machine to send packets to e1 rx. Reason of the panic is that list_first_entry() is blindly called in macvlan_handle_frame() even if the list was empty. vlan is set to incorrect pointer which leads to the crash. I'm fixing this by protecting port->vlans list by rcu and by preventing from getting incorrect pointer in case the list is empty. Introduced by: commit eb06acdc85585f2 "macvlan: Introduce 'passthru' mode to takeover the underlying device" Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-193c59x: fix PCI resource managementSergei Shtylyov
[ Upstream commit 4b264a1676e70dc656ba53a8cac690f2d4b65f4e ] The driver wrongly claimed I/O ports at an address returned by pci_iomap() -- even if it was passed an MMIO address. Fix this by claiming/releasing all PCI resources in the PCI driver's probe()/remove() methods instead and get rid of 'must_free_region' flag weirdness (why would Cardbus claim anything for us?). Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-193c59x: fix freeing nonexistent resource on driver unloadSergei Shtylyov
[ Upstream commit c81400be716aa4c76f6ebf339ba94358dbbf6da6 ] When unloading the driver that drives an EISA board, a message similar to the following one is displayed: Trying to free nonexistent resource <0000000000013000-000000000001301f> Then an user is unable to reload the driver because the resource it requested in the previous load hasn't been freed. This happens most probably due to a typo in vortex_eisa_remove() which calls release_region() with 'dev->base_addr' instead of 'edev->base_addr'... Reported-by: Matthew Whitehead <tedheadster@gmail.com> Tested-by: Matthew Whitehead <tedheadster@gmail.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-193c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)Matthew Whitehead
[ Upstream commit 3b54912f9cd167641b91d4a697bd742f70e534fe ] The venerable 3c509 driver only sets its device parent in one case, the ISAPnP one. It does this with the SET_NETDEV_DEV function. It should register with the device hierarchy in two additional cases: standard (non-PnP) ISA and EISA. - Currently they appear here: /sys/devices/virtual/net/eth0 (standard ISA) /sys/devices/virtual/net/eth1 (EISA) - Rather, they should instead be here: /sys/devices/isa/3c509.0/net/eth0 (standard ISA) /sys/devices/pci0000:00/0000:00:07.0/00:04/net/eth1 (EISA) Tested on ISA and EISA boards. Signed-off-by: Matthew Whitehead <tedheadster@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19sfc: Fix naming of MTD partitions for FPGA bitfilesBen Hutchings
[ Upstream commit 89cc80a44b7c320e08599cb86f6aef0ead8986a1 ] efx_mcdi_get_board_cfg() uses a buffer for the firmware response that is only large enough to hold subtypes for the originally defined set of NVRAM partitions. Longer responses are truncated, and we may read off the end of the buffer when copying out subtypes for additional partitions. In particular, this can result in the MTD partition for an FPGA bitfile being named e.g. 'eth5 sfc_fpga:00' when it should be 'eth5 sfc_fpga:01'. This means the firmware update tool (sfupdate) can't tell which bitfile should be written to the partition. Correct the response buffer size. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19net: qmi_wwan: prevent duplicate mac address on link (firmware bug workaround)Bjørn Mork
[ Upstream commit cc6ba5fdaabea7a7b28de3ba1e0fe54d92232fe5 ] We normally trust and use the CDC functional descriptors provided by a number of devices. But some of these will erroneously list the address reserved for the device end of the link. Attempting to use this on both the device and host side will naturally not work. Work around this bug by ignoring the functional descriptor and assign a random address instead in this case. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19net: qmi_wwan: fixup destination address (firmware bug workaround)Bjørn Mork
[ Upstream commit 6483bdc9d76fb98174797516a19d289eb837909e ] Received packets are sometimes addressed to 00:a0:c6:00:00:00 instead of the address the device firmware should have learned from the host: 321.224126 77.16.85.204 -> 148.122.171.134 ICMP 98 Echo (ping) request id=0x4025, seq=64/16384, ttl=64 0000 82 c0 82 c9 f1 67 82 c0 82 c9 f1 67 08 00 45 00 .....g.....g..E. 0010 00 54 00 00 40 00 40 01 57 cc 4d 10 55 cc 94 7a .T..@.@.W.M.U..z 0020 ab 86 08 00 62 fc 40 25 00 40 b2 bc 6e 51 00 00 ....b.@%.@..nQ.. 0030 00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15 ..k............. 0040 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 .......... !"#$% 0050 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 &'()*+,-./012345 0060 36 37 67 321.240607 148.122.171.134 -> 77.16.85.204 ICMP 98 Echo (ping) reply id=0x4025, seq=64/16384, ttl=55 0000 00 a0 c6 00 00 00 02 50 f3 00 00 00 08 00 45 00 .......P......E. 0010 00 54 00 56 00 00 37 01 a0 76 94 7a ab 86 4d 10 .T.V..7..v.z..M. 0020 55 cc 00 00 6a fc 40 25 00 40 b2 bc 6e 51 00 00 U...j.@%.@..nQ.. 0030 00 00 6b bd 09 00 00 00 00 00 10 11 12 13 14 15 ..k............. 0040 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 .......... !"#$% 0050 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 &'()*+,-./012345 0060 36 37 67 The bogus address is always the same, and matches the address suggested by many devices as a default address. It is likely a hardcoded firmware default. The circumstances where this bug has been observed indicates that the trigger is related to timing or some other factor the host cannot control. Repeating the exact same configuration sequence that caused it to trigger once, will not necessarily cause it to trigger the next time. Reproducing the bug is therefore difficult. This opens up a possibility that the bug is more common than we can confirm, because affected devices often will work properly again after a reset. A procedure most users are likely to try out before reporting a bug. Unconditionally rewriting the destination address if the first digit of the received packet is 0, is considered an acceptable compromise since we already have to inspect this digit. The simplification will cause unnecessary rewrites if the real address starts with 0, but this is still better than adding additional tests for this particular case. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19net: qmi_wwan: fixup missing ethernet header (firmware bug workaround)Bjørn Mork
[ Upstream commit 6ff509af3869ccac69dcf8905fc75b9a76951594 ] A number of LTE devices from different vendors all suffer from the same firmware bug: Most of the packets received from the device while it is attached to a LTE network will not have an ethernet header. The devices work as expected when attached to 2G or 3G networks, sending an ethernet header with all packets. This driver is not aware of which network the modem attached to, and even if it were there are still some packet types which are always received with the header intact. All devices supported by this driver have severely limited networking capabilities: - can only transmit IPv4, IPv6 and possibly ARP - can only support a single host hardware address at any time - will only do point-to-point communcation with the host Because of this, we are able to reliably identify any bogus raw IP packets by simply looking at the 4 IP version bits. All we need to do is to avoid 4 or 6 in the first digit of the mac address. This workaround ensures this, and fix up the received packets as necessary. Given the distribution of the bug, it is believed that the source is the chipset vendor. The devices which are verified to be affected are: Huawei E392u-12 (Qualcomm MDM9200) Pantech UML290 (Qualcomm MDM9600) Novatel USB551L (Qualcomm MDM9600) Novatel E362 (Qualcomm MDM9600) It is believed that the bug depend on firmware revision, which means that possibly all devices based on the above mentioned chipset may be affected if we consider all available firmware revisions. The information about affected devices and versions is likely incomplete. As the additional overhead for packets not needing this fixup is very small, it is considered acceptable to apply the workaround to all devices handled by this driver. Reported-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19drm/mm: fix dump table BUGDaniel Vetter
commit 3a359f0b21ab218c1bf7a6a1b638b6fd143d0b99 upstream. In commit 9e8944ab564f2e3dde90a518cd32048c58918608 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Thu Nov 15 11:32:17 2012 +0000 drm: Introduce an iterator over holes in the drm_mm range manager helpers and iterators for hole handling have been introduced with some debug BUG_ONs sprinkled over. Unfortunately this broke the mm dumper which unconditionally tried to compute the size of the very first hole. While at it unify the code a bit with the hole dumping in the loop. v2: Extract a hole dump helper. Reported-by: Christopher Harvey <charvey@matrox.com> Cc: Christopher Harvey <charvey@matrox.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19B43: Handle DMA RX descriptor underrunThommy Jakobsson
commit 73b82bf0bfbf58e6ff328d3726934370585f6e78 upstream. Add handling of rx descriptor underflow. This fixes a fault that could happen on slow machines, where data is received faster than the CPU can handle. In such a case the device will use up all rx descriptors and refuse to send any more data before confirming that it is ok. This patch enables necessary interrupt to discover such a situation and will handle them by dropping everything in the ring buffer. Reviewed-by: Michael Buesch <m@bues.ch> Signed-off-by: Thommy Jakobsson <thommyj@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19mwifiex: fix setting of multicast filterDaniel Drake
commit ccd384b10420ac81ba3fb9b0a7d18272c7173552 upstream. A small bug in this code was causing the ALLMULTI filter to be set when in fact we were just wanting to program a selective multicast list to the hardware. Fix that bug and remove a redundant if condition in the code that follows. This fixes wakeup behaviour when multicast WOL is enabled. Previously, all multicast packets would wake up the system. Now, only those that the host intended to receive trigger wakeups. Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19mwifiex: clear is_suspended flag when interrupt is received earlyBing Zhao
commit 48795424acff7215d5eac0b52793a2c1eb3a6283 upstream. When the XO-4 with 8787 wireless is woken up due to wake-on-WLAN mwifiex is often flooded with "not allowed while suspended" messages and the interface is unusable. [ 202.171609] int: sdio_ireg = 0x1 [ 202.180700] info: mwifiex_process_hs_config: auto cancelling host sleep since there is interrupt from the firmware [ 202.201880] event: wakeup device... [ 202.211452] event: hs_deactivated [ 202.514638] info: --- Rx: Data packet --- [ 202.514753] data: 4294957544 BSS(0-0): Data <= kernel [ 202.514825] PREP_CMD: device in suspended state [ 202.514839] data: dequeuing the packet ec7248c0 ec4869c0 [ 202.514886] mwifiex_write_data_sync: not allowed while suspended [ 202.514886] host_to_card, write iomem (1) failed: -1 [ 202.514917] mwifiex_write_data_sync: not allowed while suspended [ 202.514936] host_to_card, write iomem (2) failed: -1 [ 202.514949] mwifiex_write_data_sync: not allowed while suspended [ 202.514965] host_to_card, write iomem (3) failed: -1 [ 202.514976] mwifiex_write_data_async failed: 0xFFFFFFFF This can be readily reproduced when putting the XO-4 in a loop where it goes to sleep due to inactivity, but then wakes up due to an incoming ping. The error is hit within an hour or two. This issue happens when an interrupt comes in early while host sleep is still activated. Driver handles this case by auto cancelling host sleep. However is_suspended flag is still set which prevents any cmd or data from being sent to firmware. Fix it by clearing is_suspended flag in this path. Reported-by: Daniel Drake <dsd@laptop.org> Tested-by: Daniel Drake <dsd@laptop.org> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-05-19ath9k: fix key allocation error handling for powersave keysFelix Fietkau
commit 4ef69d0394cba8caa9f75d3f2e53429bfb8b3045 upstream. If no keycache slots are available, ath_key_config can return -ENOSPC. If the key index is not checked for errors, it can lead to logspam that looks like this: "ath: wiphy0: keyreset: keycache entry 228 out of range" This can cause follow-up errors if the invalid keycache index gets used for tx. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-09 18:16:47 +0000