| Age | Commit message (Collapse) | Author |
|---|
|
commit b579fa52f6be0b4157ca9cc5e94d44a2c89a7e95 upstream.
This patch adds support for the Schweitzer Engineering Laboratories
C662 USB cable based off the CP210x driver.
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7681156982026ebf7eafd7301eb0374d7648d068 upstream.
Added support for MMB Networks and Planet Innovation Ingeni ZigBee USB
devices using customized Silicon Labs' CP210x.c USB to UART bridge
drivers with PIDs: 88A4, 88A5.
Signed-off-by: Sami Rahman <sami.rahman@mmbresearch.com>
Tested-by: Sami Rahman <sami.rahman@mmbresearch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90625070c4253377025878c4e82feed8b35c7116 upstream.
This adds NetGear Managed Switch M4100 series, M5300 series, M7100 series
USB ID (0846:0110) to the cp210x driver. Without this, the serial
adapter is not recognized in Linux. Description was obtained from
an Netgear Eng.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 63b5df963f52ccbab6fabedf05b7ac6b465789a4 upstream.
This patch adds support for the ONYX 3G device (version 1) from ALFA
NETWORK.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca24763588844b14f019ffc45c7df6d9e8f932c5 upstream.
Adding support for D-Link DWM-152/C1 and DWM-156/C1 devices.
DWM-152/C1:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=07d1 ProdID=3e01 Rev= 0.00
S: Product=USB Configuration
S: SerialNumber=1234567890ABCDEF
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
DWM-156/C1:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=07d1 ProdID=3e02 Rev= 0.00
S: Product=DataCard Device
S: SerialNumber=1234567890ABCDEF
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c38e83b6cc2adf80e3f091fd92cfbeacc9748347 upstream.
This patch was tested on 3.10.1 kernel.
Same models of Petatel NP10T modems have different device IDs.
Unfortunately they have no additional revision information on a board
which may treat them as different devices. Currently I've seen only
two NP10T devices with various IDs. Possibly Petatel NP10T list will
be appended upon devices with new IDs will appear.
Signed-off-by: Daniil Bolsun <dan.bolsun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 878c69aae986ae97084458c0183a8c0a059865b1 upstream.
Some (very few) early devices like mine, where not exposting a proper CDC
descriptor. This was fixed with an immediate firmware update from the vendor,
and pre-installed on newer devices.
So actual devices can be driven by cdc_acm.c + cdc_ether.c.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4cf76df06ecc852633ed927d91e01c83c33bc331 upstream.
Speaks AT on interfaces 5 (command & PPP) and 3 (secondary), other
interface protocols are unknown.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94190301ffa059c2d127b3a67ec5d161d5c62681 upstream.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d1a69e726406ab662ab88fa30a3a05ed404334d upstream.
Prevent the option driver from binding itself to the QMI/WWAN interface, making
it unusable by the proper driver.
Signed-off-by: enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5fea4291deacd80188b996d2f555fc6a1940e5d4 upstream.
Commit 86a9668a8d29ea711613e1cb37efa68e7c4db564
"[SCSI] zfcp: support for hardware data router"
reduced the initial block queue limits in the scsi_host_template to the
absolute minimum and adjusted them later on. However, the adjustment was
too late for the BSG devices of Scsi_Host and fc_host.
Therefore, ioctl(..., SG_IO, ...) with request or response size > 4kB to a
BSG device of an fc_host or a Scsi_Host fails with EINVAL. As a result,
users of such ioctl such as HBA_SendCTPassThru() in libzfcphbaapi return
with error HBA_STATUS_ERROR.
Initialize the block queue limits in zfcp_scsi_host_template to the
greatest common denominator (GCD).
While we cannot exploit the slightly enlarged maximum request size with
data router, this should be neglectible. Doing so also avoids running into
trouble after live guest relocation (LGR) / migration from a data router
FCP device to an FCP device that does not support data router. In that
case, zfcp would figure out the new limits on adapter recovery, but the
fc_host and Scsi_Host (plus in fact all sdevs) still exist with the old and
now too large queue limits.
It should also OK, not to use half the size as in the DIX case, because
fc_host and Scsi_Host do not transport FCP requests including SCSI commands
using protection data.
[Backported for 3.4-stable. commit a53c8fa since v3.6-rc1 unified
copyright messages, e.g: revise such messages 'Copyright IBM Corporation'
as 'Copyright IBM Corp', so updated the messages as a53c8fa did. - zliu]
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Zhouping Liu <zliu@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 16da05b1158d1bcb31656e636a8736a663b1cf1f upstream.
gcc 4.8 warns because the memset only clears sizeof(char *) bytes, not
the whole buffer. Use the correct buffer size and clear the whole sense
buffer.
/backup/lsrc/git/linux-lto-2.6/drivers/scsi/bnx2fc/bnx2fc_io.c: In
function 'bnx2fc_parse_fcp_rsp':
/backup/lsrc/git/linux-lto-2.6/drivers/scsi/bnx2fc/bnx2fc_io.c:1810:41:
warning: argument to 'sizeof' in 'memset' call is the same expression as
the destination; did you mean to provide an explicit length?
[-Wsizeof-pointer-memaccess]
memset(sc_cmd->sense_buffer, 0, sizeof(sc_cmd->sense_buffer));
^
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a6a731bd00ca90d0e250867c3b9c05b5ff0fa49 upstream.
commit 98cb7e44 ([SCSI] megaraid_sas: Sanity check user
supplied length before passing it to dma_alloc_coherent())
introduced a memory leak. Memory allocated for entries
following zero length SGL entries will not be freed.
Reference: http://bugs.debian.org/688198
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 584ec4355355ffac43571b02a314d43eb2f7fcbf ]
Ben Hutchings pointed out that my recent update to atl1e
in commit 352900b583b2852152a1e05ea0e8b579292e731e
("atl1e: fix dma mapping warnings") was missing a bit of code.
Specifically it reset the hardware tx ring to its origional state when
we hit a dma error, but didn't unmap any exiting mappings from the
operation. This patch fixes that up. It also remembers to free the
skb in the event that an error occurs, so we don't leak. Untested, as
I don't have hardware. I think its pretty straightforward, but please
review closely.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 352900b583b2852152a1e05ea0e8b579292e731e ]
Recently had this backtrace reported:
WARNING: at lib/dma-debug.c:937 check_unmap+0x47d/0x930()
Hardware name: System Product Name
ATL1E 0000:02:00.0: DMA-API: device driver failed to check map error[device
address=0x00000000cbfd1000] [size=90 bytes] [mapped as single]
Modules linked in: xt_conntrack nf_conntrack ebtable_filter ebtables
ip6table_filter ip6_tables snd_hda_codec_hdmi snd_hda_codec_realtek iTCO_wdt
iTCO_vendor_support snd_hda_intel acpi_cpufreq mperf coretemp btrfs zlib_deflate
snd_hda_codec snd_hwdep microcode raid6_pq libcrc32c snd_seq usblp serio_raw xor
snd_seq_device joydev snd_pcm snd_page_alloc snd_timer snd lpc_ich i2c_i801
soundcore mfd_core atl1e asus_atk0110 ata_generic pata_acpi radeon i2c_algo_bit
drm_kms_helper ttm drm i2c_core pata_marvell uinput
Pid: 314, comm: systemd-journal Not tainted 3.9.0-0.rc6.git2.3.fc19.x86_64 #1
Call Trace:
<IRQ> [<ffffffff81069106>] warn_slowpath_common+0x66/0x80
[<ffffffff8106916c>] warn_slowpath_fmt+0x4c/0x50
[<ffffffff8138151d>] check_unmap+0x47d/0x930
[<ffffffff810ad048>] ? sched_clock_cpu+0xa8/0x100
[<ffffffff81381a2f>] debug_dma_unmap_page+0x5f/0x70
[<ffffffff8137ce30>] ? unmap_single+0x20/0x30
[<ffffffffa01569a1>] atl1e_intr+0x3a1/0x5b0 [atl1e]
[<ffffffff810d53fd>] ? trace_hardirqs_off+0xd/0x10
[<ffffffff81119636>] handle_irq_event_percpu+0x56/0x390
[<ffffffff811199ad>] handle_irq_event+0x3d/0x60
[<ffffffff8111cb6a>] handle_fasteoi_irq+0x5a/0x100
[<ffffffff8101c36f>] handle_irq+0xbf/0x150
[<ffffffff811dcb2f>] ? file_sb_list_del+0x3f/0x50
[<ffffffff81073b10>] ? irq_enter+0x50/0xa0
[<ffffffff8172738d>] do_IRQ+0x4d/0xc0
[<ffffffff811dcb2f>] ? file_sb_list_del+0x3f/0x50
[<ffffffff8171c6b2>] common_interrupt+0x72/0x72
<EOI> [<ffffffff810db5b2>] ? lock_release+0xc2/0x310
[<ffffffff8109ea04>] lg_local_unlock_cpu+0x24/0x50
[<ffffffff811dcb2f>] file_sb_list_del+0x3f/0x50
[<ffffffff811dcb6d>] fput+0x2d/0xc0
[<ffffffff811d8ea1>] filp_close+0x61/0x90
[<ffffffff811fae4d>] __close_fd+0x8d/0x150
[<ffffffff811d8ef0>] sys_close+0x20/0x50
[<ffffffff81725699>] system_call_fastpath+0x16/0x1b
The usual straighforward failure to check for dma_mapping_error after a map
operation is completed.
This patch should fix it, the reporter wandered off after filing this bz:
https://bugzilla.redhat.com/show_bug.cgi?id=954170
and I don't have hardware to test, but the fix is pretty straightforward, so I
figured I'd post it for review.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f2966cd5691058b8674a20766525bedeaea9cbcf ]
If __rtnl_link_register() return faild when loading the ifb, it will
take the wrong path and get oops, so fix it just like dummy.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2c8a01894a12665d8059fad8f0a293c98a264121 ]
We rename the dummy in modprobe.conf like this:
install dummy0 /sbin/modprobe -o dummy0 --ignore-install dummy
install dummy1 /sbin/modprobe -o dummy1 --ignore-install dummy
We got oops when we run the command:
modprobe dummy0
modprobe dummy1
------------[ cut here ]------------
[ 3302.187584] BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
[ 3302.195411] IP: [<ffffffff813fe62a>] __rtnl_link_unregister+0x9a/0xd0
[ 3302.201844] PGD 85c94a067 PUD 8517bd067 PMD 0
[ 3302.206305] Oops: 0002 [#1] SMP
[ 3302.299737] task: ffff88105ccea300 ti: ffff880eba4a0000 task.ti: ffff880eba4a0000
[ 3302.307186] RIP: 0010:[<ffffffff813fe62a>] [<ffffffff813fe62a>] __rtnl_link_unregister+0x9a/0xd0
[ 3302.316044] RSP: 0018:ffff880eba4a1dd8 EFLAGS: 00010246
[ 3302.321332] RAX: 0000000000000000 RBX: ffffffff81a9d738 RCX: 0000000000000002
[ 3302.328436] RDX: 0000000000000000 RSI: ffffffffa04d602c RDI: ffff880eba4a1dd8
[ 3302.335541] RBP: ffff880eba4a1e18 R08: dead000000200200 R09: dead000000100100
[ 3302.342644] R10: 0000000000000080 R11: 0000000000000003 R12: ffffffff81a9d788
[ 3302.349748] R13: ffffffffa04d7020 R14: ffffffff81a9d670 R15: ffff880eba4a1dd8
[ 3302.364910] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3302.370630] CR2: 0000000000000008 CR3: 000000085e15e000 CR4: 00000000000427e0
[ 3302.377734] DR0: 0000000000000003 DR1: 00000000000000b0 DR2: 0000000000000001
[ 3302.384838] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 3302.391940] Stack:
[ 3302.393944] ffff880eba4a1dd8 ffff880eba4a1dd8 ffff880eba4a1e18 ffffffffa04d70c0
[ 3302.401350] 00000000ffffffef ffffffffa01a8000 0000000000000000 ffffffff816111c8
[ 3302.408758] ffff880eba4a1e48 ffffffffa01a80be ffff880eba4a1e48 ffffffffa04d70c0
[ 3302.416164] Call Trace:
[ 3302.418605] [<ffffffffa01a8000>] ? 0xffffffffa01a7fff
[ 3302.423727] [<ffffffffa01a80be>] dummy_init_module+0xbe/0x1000 [dummy0]
[ 3302.430405] [<ffffffffa01a8000>] ? 0xffffffffa01a7fff
[ 3302.435535] [<ffffffff81000322>] do_one_initcall+0x152/0x1b0
[ 3302.441263] [<ffffffff810ab24b>] do_init_module+0x7b/0x200
[ 3302.446824] [<ffffffff810ad3d2>] load_module+0x4e2/0x530
[ 3302.452215] [<ffffffff8127ae40>] ? ddebug_dyndbg_boot_param_cb+0x60/0x60
[ 3302.458979] [<ffffffff810ad5f1>] SyS_init_module+0xd1/0x130
[ 3302.464627] [<ffffffff814b9652>] system_call_fastpath+0x16/0x1b
[ 3302.490090] RIP [<ffffffff813fe62a>] __rtnl_link_unregister+0x9a/0xd0
[ 3302.496607] RSP <ffff880eba4a1dd8>
[ 3302.500084] CR2: 0000000000000008
[ 3302.503466] ---[ end trace 8342d49cd49f78ed ]---
The reason is that when loading dummy, if __rtnl_link_register() return failed,
the init_module should return and avoid take the wrong path.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 61d46bf979d5cd7c164709a80ad5676a35494aae ]
Userspace may produce vectors greater than MAX_SKB_FRAGS. When we try to
linearize parts of the skb to let the rest of iov to be fit in
the frags, we need count copylen into linear when calling macvtap_alloc_skb()
instead of partly counting it into data_len. Since this breaks
zerocopy_sg_from_iovec() since its inner counter assumes nr_frags should
be zero at beginning. This cause nr_frags to be increased wrongly without
setting the correct frags.
This bug were introduced from b92946e2919134ebe2a4083e4302236295ea2a73
(macvtap: zerocopy: validate vectors before building skb).
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 440d57bc5ff55ec1efb3efc9cbe9420b4bbdfefa ]
According to the commit 16b0dc29c1af9df341428f4c49ada4f626258082
(dummy: fix rcu_sched self-detected stalls)
Eric Dumazet fix the problem in dummy, but the ifb will occur the
same problem like the dummy modules.
Trying to "modprobe ifb numifbs=30000" triggers :
INFO: rcu_sched self-detected stall on CPU
After this splat, RTNL is locked and reboot is needed.
We must call cond_resched() to avoid this, even holding RTNL.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit aabb9875d02559ab9b928cd6f259a5cc4c21a589 ]
The missing call to unregister_netdev() leaves the interface active
after the driver is unloaded by rmmod.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ca8c35852138ee0585eaffe6b9f10a5261ea7771 ]
EESR.RFE (receive FIFO overflow) interrupt is enabled by the driver on all SoCs
and sh_eth_error() handles it but it's not present in any initializer/assignment
of the 'eesr_err_check' field of 'struct sh_eth_cpu_data'. This leads to that
interrupt not being handled and cleared, and finally to disabling IRQ and the
driver being non-functional.
Modify DEFAULT_EESR_ERR_CHECK macro and all explicit initializers of the above
mentioned field to contain the EESR.RFE bit. Remove useless backslashes from the
initializers, while at it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4c7ab054ab4f5d63625508ed6f8a607184cae7c2 ]
get user pages might fail partially in macvtap zero copy
mode. To recover we need to put all pages that we got,
but code used a wrong index resulting in double-free
errors.
Reported-by: Brad Hubbard <bhubbard@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 60d0ca3cfd199b6612bbbbf4999a3470dad38bb1 upstream.
If we use a large mapping, the expectation is that only unmaps from
the first pte in the superpage are supported. Unmaps from offsets
into the superpage should fail (ie. return zero sized unmap). In the
current code, unmapping from an offset clears the size of the full
mapping starting from an offset. For instance, if we map a 16k
physically contiguous range at IOVA 0x0 with a large page, then
attempt to unmap 4k at offset 12k, 4 ptes are cleared (12k - 28k) and
the unmap returns 16k unmapped. This potentially incorrectly clears
valid mappings and confuses drivers like VFIO that use the unmap size
to release pinned pages.
Fix by refusing to unmap from offsets into the page.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 48ba2efc382f94fae16ca8ca011e5961a81ad1ea upstream.
When SCSI command is received with task attribute not set, set it to SIMPLE.
Previously it is set to untagged. This causes the firmware to fail the commands.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f76ccaac4f82c463a037aa4a1e4ccb85c7011814 upstream.
FCP device remains in status ERP_FAILED when device is switched online
or adapter recovery is triggered while link to SAN is down.
When Exchange Configuration Data command returns the FSF status
FSF_EXCHANGE_CONFIG_DATA_INCOMPLETE it aborts the exchange process.
The only retries are done during the common error recovery procedure
(i.e. max. 3 retries with 8sec sleep between) and remains in status
ERP_FAILED with QDIO down.
This commit reverts the commit 0df138476c8306478d6e726f044868b4bccf411c
(zfcp: Fix adapter activation on link down).
When FSF status FSF_EXCHANGE_CONFIG_DATA_INCOMPLETE is received the
adapter recovery will be finished without any retries. QDIO will be
up now and status changes such as LINK UP will be received now.
Signed-off-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d3bcb7b24bbf09fde8405770e676fe0c11c79662 upstream.
ah->noise is maintained globally and not per-channel. This
is updated in the reset() routine after the NF history has been
filled for the *current channel*, just before switching to
the new channel. There is no need to do it inside getnf(), since
ah->noise must contain a value for the new channel.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a6f3a8ebaf13407523c2c7d575b4ca2debd23ba upstream.
The current code uses the same index value both
for the channel information array and for the TX
power table. The index starts from 14, however the
index of the TX power table must start from zero.
Fix it, in order to get the correct TX power value
for a given channel.
The changes in rt61pci.c and rt73usb.c are compile
tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c7e8695bfa0611b39493a9dfe8bab9f63f9809bd upstream.
This patch adds the IDE-mode SATA DeviceIDs for the Intel Coleto Creek PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a87718d92760fc688628ad6a430643dafa16f1f upstream.
For some reason, a lot of port-multipliers have issues with softreset.
SIMG [34]7x series port-multipliers have been quite erratic in this
regard. I recall that it was better with some firmware revisions and
the current list of quirks worked fine for a while. I think it got
worse with later firmwares or maybe my test coverage wasn't good
enough. Anyways, HPA is reporting that his 3726 setup suffers SRST
failures and then the PMP gets confused and fails to probe the last
port.
The hope was that we try to stick to the standard as much as possible
and soonish the PMPs and their firmwares will improve in quality, so
the quirk list was kept to minimum. Well, it seems like that's never
gonna happen.
Let's set NO_SRST for all [34]7x PMPs so that whatever remaining
userbase of the device suffer the least. Maybe we should do the same
for 57xx's but unfortunately I don't have any device left to test and
I'm not even sure 57xx's have ever been made widely available, so
let's leave those alone for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da331ba8e9c5de72a27e50f71105395bba6eebe0 upstream.
tasklet_kill() may sleep so call it before taking pch->lock.
Fixes following lockup:
BUG: scheduling while atomic: cat/2383/0x00000002
Modules linked in:
unwind_backtrace+0x0/0xfc
__schedule_bug+0x4c/0x58
__schedule+0x690/0x6e0
sys_sched_yield+0x70/0x78
tasklet_kill+0x34/0x8c
pl330_free_chan_resources+0x24/0x88
dma_chan_put+0x4c/0x50
[...]
BUG: spinlock lockup suspected on CPU#0, swapper/0/0
lock: 0xe52aa04c, .magic: dead4ead, .owner: cat/2383, .owner_cpu: 1
unwind_backtrace+0x0/0xfc
do_raw_spin_lock+0x194/0x204
_raw_spin_lock_irqsave+0x20/0x28
pl330_tasklet+0x2c/0x5a8
tasklet_action+0xfc/0x114
__do_softirq+0xe4/0x19c
irq_exit+0x98/0x9c
handle_IPI+0x124/0x16c
gic_handle_irq+0x64/0x68
__irq_svc+0x40/0x70
cpuidle_wrap_enter+0x4c/0xa0
cpuidle_enter_state+0x18/0x68
cpuidle_idle_call+0xac/0xe0
cpu_idle+0xac/0xf0
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 912b9ac683b112615d5605686f1dc086402ce9f7 upstream.
ata_link_online() check in ahci_error_intr() is unnecessary, it should
be removed otherwise may lead to lockup with FBS enabled PMP.
http://marc.info/?l=linux-ide&m=137050421603272&w=2
Reported-by: Yu Liu <liuyu.ac@gmail.com>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fafe5c3d82a470d73de53e6b08eb4e28d974d895 upstream.
To add AMD CZ SATA controller device ID of IDE mode.
[bhelgaas: drop pci_ids.h update]
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eff9a4b62b14cf0d9913e3caf1f26f8b7a6105c9 upstream.
HP Folio 13's BIOS defines CMOS RTC Operation Region and the EC's
_REG method will access that region. To allow the CMOS RTC region
handler to be installed before the EC _REG method is first invoked,
add ec_skip_dsdt_scan() as HP Folio 13's callback to ec_dmi_table.
References: https://bugzilla.kernel.org/show_bug.cgi?id=54621
Reported-and-tested-by: Stefan Nagy <public@stefan-nagy.at>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29ecd78c0fd6ee05f2c6b07b23823a6ae43c13ff upstream.
In the disable AIE irq code path, current code passes "1" to enable
parameter of rv3029c2_rtc_i2c_alarm_set_irq(). Thus it does not disable
AIE irq.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e39506b466edcda2a7e9d0174d7987ae654137b7 upstream.
Commit 80af9e6d (pcmcia at91_cf: fix raw gpio number usage) forgot
to change the parameter in gpio_get_value after adding gpio
validation.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5388a3a5faba8dfa69e5f06c3a415d373c1a4316 upstream.
Do a release_mem_region of the hcd resource. Without this the
subsequent insertion of module fails in request_mem_region.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 025f880cb2e4d7218d0422d4b07bea1a68959c38 upstream.
Fail and free the container context in case dma_pool_alloc() can't allocate
the raw context data part of it
This patch should be backported to kernels as old as 2.6.31, that
contain the commit d115b04818e57bdbc7ccde4d0660b15e33013dc8 "USB: xhci:
Support for 64-byte contexts".
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d68c277b501889b3a50c179d1c3d704db7947b83 upstream.
Without this memory barrier, the file-storage thread may fail to
escape from the following while loop, because it may observe new
common->thread_wakeup_needed and old bh->state which are updated by
the callback functions.
/* Wait for the CBW to arrive */
while (bh->state != BUF_STATE_FULL) {
rc = sleep_thread(common);
if (rc)
return rc;
}
Signed-off-by: UCHINO Satoshi <satoshi.uchino@toshiba.co.jp>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a254810a86aaaac4ac6ba44fa934558b042a17a7 upstream.
These devices are all Gobi1K devices (according to the Windows INF
files) and should be handled by qcserial instead of option. Their
network port is handled by qmi_wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 10d0b9030a3f86e1e26c710c7580524d7787d688 upstream.
A typo causes routine rtl92cu_phy_rf6052_set_cck_txpower() to test the
same condition twice. The problem was found using cppcheck-1.49, and the
proper fix was verified against the pre-mac80211 version of the code.
This patch was originally included as commit 1288aa4, but was accidentally
reverted in a later patch.
Reported-by: David Binderman <dcb314@hotmail.com> [original report]
Reported-by: Andrea Morello <andrea.merello@gmail.com> [report of accidental reversion]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c4d827c5ccc3a49227dbf9d4b248a2e86f388023 upstream.
This is a new device for this driver.
Reported-by: Tobias Kluge <zielscheibe@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Tobias Kluge <zielscheibe@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2ee3e26c673e75c05ef8b914f54fadee3d7b9c88 upstream.
Commit 39c60a0948cc '[SCSI] sd: fix array cache flushing bug causing
performance problems' added temp as a pointer to "temporary " and used
sizeof(temp) - 1 as its length. But sizeof(temp) is the size of the
pointer, not the size of the string constant. Change temp to a static
array so that sizeof() does what was intended.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PCI 9835 Multi-I/O Controller"
commit 828c6a102b1f2b8583fadc0e779c46b31d448f0b upstream.
This reverts commit 8d2f8cd424ca0b99001f3ff4f5db87c4e525f366.
As reported by Stefan, this device already works with the parport_serial
driver, so the 8250_pci driver should not also try to grab it as well.
Reported-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Cc: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ffc8b30866879ed9ba62bd0a86fecdbd51cd3d19 upstream.
Disk names may contain arbitrary strings, so they must not be
interpreted as format strings. It seems that only md allows arbitrary
strings to be used for disk names, but this could allow for a local
memory corruption from uid 0 into ring 0.
CVE-2013-2851
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3594f4c0d7bc51e3a7e6d73c44e368ae079e42f3 upstream.
The exposed interface for cm_notify_event() could result in the event msg
string being parsed as a format string. Make sure it is only used as a
literal string.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 542db01579fbb7ea7d1f7bb9ddcef1559df660b2 upstream.
In drivers/cdrom/cdrom.c mmc_ioctl_cdrom_read_data() allocates a memory
area with kmalloc in line 2885.
2885 cgc->buffer = kmalloc(blocksize, GFP_KERNEL);
2886 if (cgc->buffer == NULL)
2887 return -ENOMEM;
In line 2908 we can find the copy_to_user function:
2908 if (!ret && copy_to_user(arg, cgc->buffer, blocksize))
The cgc->buffer is never cleaned and initialized before this function.
If ret = 0 with the previous basic block, it's possible to display some
memory bytes in kernel space from userspace.
When we read a block from the disk it normally fills the ->buffer but if
the drive is malfunctioning there is a chance that it would only be
partially filled. The result is an leak information to userspace.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jonathan Salwan <jonathan.salwan@gmail.com>
Cc: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 384e301e3519599b000c1a2ecd938b533fc15d85 upstream.
When we use pch_uart as system console like 'console=ttyPCH0,115200',
then 'send break' to it. We'll encounter the deadlock on a cpu/core,
with interrupts disabled on the core. When we happen to have all irqs
affinity to cpu0 then the deadlock on cpu0 actually deadlock whole
system.
In pch_uart_interrupt, we have spin_lock_irqsave(&priv->lock, flags)
then call pch_uart_err_ir when break is received. Then the call to
dev_err would actually call to pch_console_write then we'll run into
another spin_lock(&priv->lock), with interrupts disabled.
So in the call sequence lead by pch_uart_interrupt, we should be
carefully to call functions that will 'print message to console' only
in case the uart port is not being used as serial console.
Signed-off-by: Liang Li <liang.li@windriver.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 578a1310f2592ba90c5674bca21c1dbd1adf3f0a upstream.
We triggered an oops while running trinity with 3.4 kernel:
BUG: unable to handle kernel paging request at 0000000100000d07
IP: [<ffffffffa0109738>] dlci_ioctl+0xd8/0x2d4 [dlci]
PGD 640c0d067 PUD 0
Oops: 0000 [#1] PREEMPT SMP
CPU 3
...
Pid: 7302, comm: trinity-child3 Not tainted 3.4.24.09+ 40 Huawei Technologies Co., Ltd. Tecal RH2285 /BC11BTSA
RIP: 0010:[<ffffffffa0109738>] [<ffffffffa0109738>] dlci_ioctl+0xd8/0x2d4 [dlci]
...
Call Trace:
[<ffffffff8137c5c3>] sock_ioctl+0x153/0x280
[<ffffffff81195494>] do_vfs_ioctl+0xa4/0x5e0
[<ffffffff8118354a>] ? fget_light+0x3ea/0x490
[<ffffffff81195a1f>] sys_ioctl+0x4f/0x80
[<ffffffff81478b69>] system_call_fastpath+0x16/0x1b
...
It's because the net device is not a dlci device.
Reported-by: Li Jinyue <lijinyue@huawei.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 11eb2645cbf38a08ae491bf6c602eea900ec0bb5 upstream.
Otherwise the net device returned can be freed at anytime.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 574780fd5e6ec52bd43e0bdb777a19e4c4c6aa9c upstream.
Here is a fun one. Bug seems to have been introduced by commit 140854cb,
almost two years ago. I have no idea why we only started seeing it now,
but we did.
Rough callgraph:
core_tpg_set_initiator_node_queue_depth()
`-> spin_lock_irqsave(&tpg->session_lock, flags);
`-> lio_tpg_shutdown_session()
`-> iscsit_stop_time2retain_timer()
`-> spin_unlock_bh(&se_tpg->session_lock);
`-> spin_lock_bh(&se_tpg->session_lock);
`-> spin_unlock_irqrestore(&tpg->session_lock, flags);
core_tpg_set_initiator_node_queue_depth() used to call spin_lock_bh(),
but 140854cb changed that to spin_lock_irqsave(). However,
lio_tpg_shutdown_session() still claims to be called with spin_lock_bh()
held, as does iscsit_stop_time2retain_timer():
* Called with spin_lock_bh(&struct se_portal_group->session_lock) held
Stale documentation is mostly annoying, but in this case the dropping
the lock with the _bh variant is plain wrong. It is also wrong to drop
locks two functions below the lock-holder, but I will ignore that bit
for now.
After some more locking and unlocking we eventually hit this backtrace:
------------[ cut here ]------------
WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0xe8/0x100()
Pid: 24645, comm: lio_helper.py Tainted: G O 3.6.11+
Call Trace:
[<ffffffff8103e5ff>] warn_slowpath_common+0x7f/0xc0
[<ffffffffa040ae37>] ? iscsit_inc_conn_usage_count+0x37/0x50 [iscsi_target_mod]
[<ffffffff8103e65a>] warn_slowpath_null+0x1a/0x20
[<ffffffff810472f8>] local_bh_enable_ip+0xe8/0x100
[<ffffffff815b8365>] _raw_spin_unlock_bh+0x15/0x20
[<ffffffffa040ae37>] iscsit_inc_conn_usage_count+0x37/0x50 [iscsi_target_mod]
[<ffffffffa041149a>] iscsit_stop_session+0xfa/0x1c0 [iscsi_target_mod]
[<ffffffffa0417fab>] lio_tpg_shutdown_session+0x7b/0x90 [iscsi_target_mod]
[<ffffffffa033ede4>] core_tpg_set_initiator_node_queue_depth+0xe4/0x290 [target_core_mod]
[<ffffffffa0409032>] iscsit_tpg_set_initiator_node_queue_depth+0x12/0x20 [iscsi_target_mod]
[<ffffffffa0415c29>] lio_target_nacl_store_cmdsn_depth+0xa9/0x180 [iscsi_target_mod]
[<ffffffffa0331b49>] target_fabric_nacl_base_attr_store+0x39/0x40 [target_core_mod]
[<ffffffff811b857d>] configfs_write_file+0xbd/0x120
[<ffffffff81148f36>] vfs_write+0xc6/0x180
[<ffffffff81149251>] sys_write+0x51/0x90
[<ffffffff815c0969>] system_call_fastpath+0x16/0x1b
---[ end trace 3747632b9b164652 ]---
As a pure band-aid, this patch drops the _bh.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
