| Age | Commit message (Collapse) | Author |
|---|
|
commit 389a5390583a18e45bc4abd4439291abec5e7a63 upstream.
Now that scatterwalk_sg_chain sets the chain pointer bit the sg_page
call in scatterwalk_sg_next hits a BUG_ON when CONFIG_DEBUG_SG is
enabled. Use sg_chain_ptr instead of sg_page on a chain entry.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 54b2b50c20a61b51199bedb6e5d2f8ec2568fb43 upstream.
Some host adapters do not pass commands through to the target disk
directly. Instead they provide an emulated target which may or may not
accurately report its capabilities. In some cases the physical device
characteristics are reported even when the host adapter is processing
commands on the device's behalf. This can lead to adapter firmware hangs
or excessive I/O errors.
This patch disables WRITE SAME for devices connected to host adapters
that provide an emulated target. Driver writers can disable WRITE SAME
by setting the no_write_same flag in the host adapter template.
[jejb: fix up rejections due to eh_deadline patch]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
completed
commit e0d59733f6b1796b8d6692642c87d7dd862c3e3a upstream.
Currently, when mounting pstore file system, a read callback of
efi_pstore driver runs mutiple times as below.
- In the first read callback, scan efivar_sysfs_list from head and pass
a kmsg buffer of a entry to an upper pstore layer.
- In the second read callback, rescan efivar_sysfs_list from the entry
and pass another kmsg buffer to it.
- Repeat the scan and pass until the end of efivar_sysfs_list.
In this process, an entry is read across the multiple read function
calls. To avoid race between the read and erasion, the whole process
above is protected by a spinlock, holding in open() and releasing in
close().
At the same time, kmemdup() is called to pass the buffer to pstore
filesystem during it. And then, it causes a following lockdep warning.
To make the dynamic memory allocation runnable without taking spinlock,
holding off a deletion of sysfs entry if it happens while scanning it
via efi_pstore, and deleting it after the scan is completed.
To implement it, this patch introduces two flags, scanning and deleting,
to efivar_entry.
On the code basis, it seems that all the scanning and deleting logic is
not needed because __efivars->lock are not dropped when reading from the
EFI variable store.
But, the scanning and deleting logic is still needed because an
efi-pstore and a pstore filesystem works as follows.
In case an entry(A) is found, the pointer is saved to psi->data. And
efi_pstore_read() passes the entry(A) to a pstore filesystem by
releasing __efivars->lock.
And then, the pstore filesystem calls efi_pstore_read() again and the
same entry(A), which is saved to psi->data, is used for resuming to scan
a sysfs-list.
So, to protect the entry(A), the logic is needed.
[ 1.143710] ------------[ cut here ]------------
[ 1.144058] WARNING: CPU: 1 PID: 1 at kernel/lockdep.c:2740 lockdep_trace_alloc+0x104/0x110()
[ 1.144058] DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
[ 1.144058] Modules linked in:
[ 1.144058] CPU: 1 PID: 1 Comm: systemd Not tainted 3.11.0-rc5 #2
[ 1.144058] 0000000000000009 ffff8800797e9ae0 ffffffff816614a5 ffff8800797e9b28
[ 1.144058] ffff8800797e9b18 ffffffff8105510d 0000000000000080 0000000000000046
[ 1.144058] 00000000000000d0 00000000000003af ffffffff81ccd0c0 ffff8800797e9b78
[ 1.144058] Call Trace:
[ 1.144058] [<ffffffff816614a5>] dump_stack+0x54/0x74
[ 1.144058] [<ffffffff8105510d>] warn_slowpath_common+0x7d/0xa0
[ 1.144058] [<ffffffff8105517c>] warn_slowpath_fmt+0x4c/0x50
[ 1.144058] [<ffffffff8131290f>] ? vsscanf+0x57f/0x7b0
[ 1.144058] [<ffffffff810bbd74>] lockdep_trace_alloc+0x104/0x110
[ 1.144058] [<ffffffff81192da0>] __kmalloc_track_caller+0x50/0x280
[ 1.144058] [<ffffffff815147bb>] ? efi_pstore_read_func.part.1+0x12b/0x170
[ 1.144058] [<ffffffff8115b260>] kmemdup+0x20/0x50
[ 1.144058] [<ffffffff815147bb>] efi_pstore_read_func.part.1+0x12b/0x170
[ 1.144058] [<ffffffff81514800>] ? efi_pstore_read_func.part.1+0x170/0x170
[ 1.144058] [<ffffffff815148b4>] efi_pstore_read_func+0xb4/0xe0
[ 1.144058] [<ffffffff81512b7b>] __efivar_entry_iter+0xfb/0x120
[ 1.144058] [<ffffffff8151428f>] efi_pstore_read+0x3f/0x50
[ 1.144058] [<ffffffff8128d7ba>] pstore_get_records+0x9a/0x150
[ 1.158207] [<ffffffff812af25c>] ? selinux_d_instantiate+0x1c/0x20
[ 1.158207] [<ffffffff8128ce30>] ? parse_options+0x80/0x80
[ 1.158207] [<ffffffff8128ced5>] pstore_fill_super+0xa5/0xc0
[ 1.158207] [<ffffffff811ae7d2>] mount_single+0xa2/0xd0
[ 1.158207] [<ffffffff8128ccf8>] pstore_mount+0x18/0x20
[ 1.158207] [<ffffffff811ae8b9>] mount_fs+0x39/0x1b0
[ 1.158207] [<ffffffff81160550>] ? __alloc_percpu+0x10/0x20
[ 1.158207] [<ffffffff811c9493>] vfs_kern_mount+0x63/0xf0
[ 1.158207] [<ffffffff811cbb0e>] do_mount+0x23e/0xa20
[ 1.158207] [<ffffffff8115b51b>] ? strndup_user+0x4b/0xf0
[ 1.158207] [<ffffffff811cc373>] SyS_mount+0x83/0xc0
[ 1.158207] [<ffffffff81673cc2>] system_call_fastpath+0x16/0x1b
[ 1.158207] ---[ end trace 61981bc62de9f6f4 ]---
Signed-off-by: Seiji Aguchi <seiji.aguchi@hds.com>
Tested-by: Madper Xie <cxie@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit faf6615bf05bc5cecc6e22013b9cb21c77784fd1 upstream.
SND_SOC_DAPM_MUX() doesn't currently initialize the .mask field. This
results in the mux never affecting HW, since no bits are ever set or
cleared. Fix SND_SOC_DAPM_MUX() to use SND_SOC_DAPM_INIT_REG_VAL() to
set up the reg, shift, on_val, and off_val fields like almost all other
SND_SOC_xxx() macros. It looks like this was a "typo" in the fixed
commit linked below.
This makes the speakers on the Toshiba AC100 (PAZ00) laptop work again.
Fixes: de9ba98b6d26 ("ASoC: dapm: Make widget power register settings more flexible")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41da8b5adba77e22584f8b45f9641504fa885308 upstream.
The scatterwalk_crypto_chain function invokes the scatterwalk_sg_chain
function to chain two scatterlists, but the chain pointer indication
bit is not set. When the resulting scatterlist is used, for example,
by sg_nents to count the number of scatterlist entries, a segfault occurs
because sg_nents does not follow the chain pointer to the chained scatterlist.
Update scatterwalk_sg_chain to set the chain pointer indication bit as is
done by the sg_chain function.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6987843ff7e836ea65b554905aec34d2fad05c94 upstream.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 72403b4a0fbdf433c1fe0127e49864658f6f6468 upstream.
Commit 0255d4918480 ("mm: Account for a THP NUMA hinting update as one
PTE update") was added to account for the number of PTE updates when
marking pages prot_numa. task_numa_work was using the old return value
to track how much address space had been updated. Altering the return
value causes the scanner to do more work than it is configured or
documented to in a single unit of work.
This patch reverts that commit and accounts for the number of THP
updates separately in vmstat. It is up to the administrator to
interpret the pair of values correctly. This is a straight-forward
operation and likely to only be of interest when actively debugging NUMA
balancing problems.
The impact of this patch is that the NUMA PTE scanner will scan slower
when THP is enabled and workloads may converge slower as a result. On
the flip size system CPU usage should be lower than recent tests
reported. This is an illustrative example of a short single JVM specjbb
test
specjbb
3.12.0 3.12.0
vanilla acctupdates
TPut 1 26143.00 ( 0.00%) 25747.00 ( -1.51%)
TPut 7 185257.00 ( 0.00%) 183202.00 ( -1.11%)
TPut 13 329760.00 ( 0.00%) 346577.00 ( 5.10%)
TPut 19 442502.00 ( 0.00%) 460146.00 ( 3.99%)
TPut 25 540634.00 ( 0.00%) 549053.00 ( 1.56%)
TPut 31 512098.00 ( 0.00%) 519611.00 ( 1.47%)
TPut 37 461276.00 ( 0.00%) 474973.00 ( 2.97%)
TPut 43 403089.00 ( 0.00%) 414172.00 ( 2.75%)
3.12.0 3.12.0
vanillaacctupdates
User 5169.64 5184.14
System 100.45 80.02
Elapsed 252.75 251.85
Performance is similar but note the reduction in system CPU time. While
this showed a performance gain, it will not be universal but at least
it'll be behaving as documented. The vmstats are obviously different but
here is an obvious interpretation of them from mmtests.
3.12.0 3.12.0
vanillaacctupdates
NUMA page range updates 1408326 11043064
NUMA huge PMD updates 0 21040
NUMA PTE updates 1408326 291624
"NUMA page range updates" == nr_pte_updates and is the value returned to
the NUMA pte scanner. NUMA huge PMD updates were the number of THP
updates which in combination can be used to calculate how many ptes were
updated from userspace.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Alex Thorlton <athorlton@sgi.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6aafeef03b9d9ecf255f3a80ed85ee070260e1ae ]
Pushing original fragments through causes several problems. For example
for matching, frags may not be matched correctly. Take following
example:
<example>
On HOSTA do:
ip6tables -I INPUT -p icmpv6 -j DROP
ip6tables -I INPUT -p icmpv6 -m icmp6 --icmpv6-type 128 -j ACCEPT
and on HOSTB you do:
ping6 HOSTA -s2000 (MTU is 1500)
Incoming echo requests will be filtered out on HOSTA. This issue does
not occur with smaller packets than MTU (where fragmentation does not happen)
</example>
As was discussed previously, the only correct solution seems to be to use
reassembled skb instead of separete frags. Doing this has positive side
effects in reducing sk_buff by one pointer (nfct_reasm) and also the reams
dances in ipvs and conntrack can be removed.
Future plan is to remove net/ipv6/netfilter/nf_conntrack_reasm.c
entirely and use code in net/ipv6/reassembly.c instead.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
functions
[ Upstream commit 85fbaa75037d0b6b786ff18658ddf0b4014ce2a4 ]
Commit bceaa90240b6019ed73b49965eac7d167610be69 ("inet: prevent leakage
of uninitialized memory to user in recv syscalls") conditionally updated
addr_len if the msg_name is written to. The recv_error and rxpmtu
functions relied on the recvmsg functions to set up addr_len before.
As this does not happen any more we have to pass addr_len to those
functions as well and set it to the size of the corresponding sockaddr
length.
This broke traceroute and such.
Fixes: bceaa90240b6 ("inet: prevent leakage of uninitialized memory to user in recv syscalls")
Reported-by: Brad Spengler <spender@grsecurity.net>
Reported-by: Tom Labanowski
Cc: mpb <mpb.mail@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f3d3342602f8bcbf37d7c46641cb9bca7618eb1c ]
This patch now always passes msg->msg_namelen as 0. recvmsg handlers must
set msg_namelen to the proper size <= sizeof(struct sockaddr_storage)
to return msg_name to the user.
This prevents numerous uninitialized memory leaks we had in the
recvmsg handlers and makes it harder for new code to accidentally leak
uninitialized memory.
Optimize for the case recvfrom is called with NULL as address. We don't
need to copy the address at all, so set it to NULL before invoking the
recvmsg handler. We can do so, because all the recvmsg handlers must
cope with the case a plain read() is called on them. read() also sets
msg_name to NULL.
Also document these changes in include/linux/net.h as suggested by David
Miller.
Changes since RFC:
Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address. It also more naturally reflects the logic by the callers of
verify_iovec.
With this change in place I could remove "
if (!uaddr || msg_sys->msg_namelen == 0)
msg->msg_name = NULL
".
This change does not alter the user visible error logic as we ignore
msg_namelen as long as msg_name is NULL.
Also remove two unnecessary curly brackets in ___sys_recvmsg and change
comments to netdev style.
Cc: David Miller <davem@davemloft.net>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f52ed89971adbe79b6438c459814034707b8ab91 ]
For performance reasons, sch_fq tried hard to not setup timers for every
sent packet, using a quantum based heuristic : A delay is setup only if
the flow exhausted its credit.
Problem is that application limited flows can refill their credit
for every queued packet, and they can evade pacing.
This problem can also be triggered when TCP flows use small MSS values,
as TSO auto sizing builds packets that are smaller than the default fq
quantum (3028 bytes)
This patch adds a 40 ms delay to guard flow credit refill.
Fixes: afe4fd062416 ("pkt_sched: fq: Fair Queue packet scheduler")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 65c5189a2b57b9aa1d89e4b79da39928257c9505 ]
Commit 7eec4174ff29 ("pkt_sched: fq: fix non TCP flows pacing")
obsoleted TCA_FQ_FLOW_DEFAULT_RATE without notice for the users.
Suggested by David Miller
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 51c37a70aaa3f95773af560e6db3073520513912 ]
For properly initialising the Tausworthe generator [1], we have
a strict seeding requirement, that is, s1 > 1, s2 > 7, s3 > 15.
Commit 697f8d0348 ("random32: seeding improvement") introduced
a __seed() function that imposes boundary checks proposed by the
errata paper [2] to properly ensure above conditions.
However, we're off by one, as the function is implemented as:
"return (x < m) ? x + m : x;", and called with __seed(X, 1),
__seed(X, 7), __seed(X, 15). Thus, an unwanted seed of 1, 7, 15
would be possible, whereas the lower boundary should actually
be of at least 2, 8, 16, just as GSL does. Fix this, as otherwise
an initialization with an unwanted seed could have the effect
that Tausworthe's PRNG properties cannot not be ensured.
Note that this PRNG is *not* used for cryptography in the kernel.
[1] http://www.iro.umontreal.ca/~lecuyer/myftp/papers/tausme.ps
[2] http://www.iro.umontreal.ca/~lecuyer/myftp/papers/tausme2.ps
Joint work with Hannes Frederic Sowa.
Fixes: 697f8d0348a6 ("random32: seeding improvement")
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26b818511c6562ce372566c219a2ef1afea35fe6 upstream.
In some platforms, specially Thinkpad series, rts5249 won't be
initialized properly. So we need adjust some phy parameters to
improve the compatibility issue.
It is a little different between simulation and real chip. We have
no idea about which configuration is better before tape-out. We set
default settings according to simulation, but need to tune these
parameters after getting the real chip.
I can't explain every change in detail here. The below information is
just a rough description:
PHY_REG_REV: Disable internal clkreq_tx, enable rx_pwst
PHY_BPCR: No change, just turn the magic number to macro definitions
PHY_PCR: Change OOBS sensitivity, from 60mV to 90mV
PHY_RCR2: Control charge-pump current automatically
PHY_FLD4: Use TX cmu reference clock
PHY_RDR: Change RXDSEL from 30nF to 1.9nF
PHY_RCR1: Change the duration between adp_st and asserting cp_en from
0.32 us to 0.64us
PHY_FLD3: Adjust internal timers
PHY_TUNE: Fine tune the regulator12 output voltage
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e58e54754dc1fec21c3a9e824bc108b05fdf46e upstream.
If an TRACE_EVENT() uses __assign_str() or __get_str on a NULL pointer
then the following oops will happen:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c127a17b>] strlen+0x10/0x1a
*pde = 00000000 ^M
Oops: 0000 [#1] PREEMPT SMP
Modules linked in:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.13.0-rc1-test+ #2
Hardware name: /DG965MQ, BIOS MQ96510J.86A.0372.2006.0605.1717 06/05/2006^M
task: f5cde9f0 ti: f5e5e000 task.ti: f5e5e000
EIP: 0060:[<c127a17b>] EFLAGS: 00210046 CPU: 1
EIP is at strlen+0x10/0x1a
EAX: 00000000 EBX: c2472da8 ECX: ffffffff EDX: c2472da8
ESI: c1c5e5fc EDI: 00000000 EBP: f5e5fe84 ESP: f5e5fe80
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 8005003b CR2: 00000000 CR3: 01f32000 CR4: 000007d0
Stack:
f5f18b90 f5e5feb8 c10687a8 0759004f 00000005 00000005 00000005 00200046
00000002 00000000 c1082a93 f56c7e28 c2472da8 c1082a93 f5e5fee4 c106bc61^M
00000000 c1082a93 00000000 00000000 00000001 00200046 00200082 00000000
Call Trace:
[<c10687a8>] ftrace_raw_event_lock+0x39/0xc0
[<c1082a93>] ? ktime_get+0x29/0x69
[<c1082a93>] ? ktime_get+0x29/0x69
[<c106bc61>] lock_release+0x57/0x1a5
[<c1082a93>] ? ktime_get+0x29/0x69
[<c10824dd>] read_seqcount_begin.constprop.7+0x4d/0x75
[<c1082a93>] ? ktime_get+0x29/0x69^M
[<c1082a93>] ktime_get+0x29/0x69
[<c108a46a>] __tick_nohz_idle_enter+0x1e/0x426
[<c10690e8>] ? lock_release_holdtime.part.19+0x48/0x4d
[<c10bc184>] ? time_hardirqs_off+0xe/0x28
[<c1068c82>] ? trace_hardirqs_off_caller+0x3f/0xaf
[<c108a8cb>] tick_nohz_idle_enter+0x59/0x62
[<c1079242>] cpu_startup_entry+0x64/0x192
[<c102299c>] start_secondary+0x277/0x27c
Code: 90 89 c6 89 d0 88 c4 ac 38 e0 74 09 84 c0 75 f7 be 01 00 00 00 89 f0 48 5e 5d c3 55 89 e5 57 66 66 66 66 90 83 c9 ff 89 c7 31 c0 <f2> ae f7 d1 8d 41 ff 5f 5d c3 55 89 e5 57 66 66 66 66 90 31 ff
EIP: [<c127a17b>] strlen+0x10/0x1a SS:ESP 0068:f5e5fe80
CR2: 0000000000000000
---[ end trace 01bc47bf519ec1b2 ]---
New tracepoints have been added that have allowed for NULL pointers
being assigned to strings. To fix this, change the TRACE_EVENT() code
to check for NULL and if it is, it will assign "(null)" to it instead
(similar to what glibc printf does).
Reported-by: Shuah Khan <shuah.kh@samsung.com>
Reported-by: Jovi Zhangwei <jovi.zhangwei@gmail.com>
Link: http://lkml.kernel.org/r/CAGdX0WFeEuy+DtpsJzyzn0343qEEjLX97+o1VREFkUEhndC+5Q@mail.gmail.com
Link: http://lkml.kernel.org/r/528D6972.9010702@samsung.com
Fixes: 9cbf117662e2 ("tracing/events: provide string with undefined size support")
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca499fc87ed945094d952da0eb7eea7dbeb1feec upstream.
The PCI host bridge scan handler installs its own notify handler,
handle_hotplug_event_root(), by itself. Nevertheless, the ACPI
hotplug framework also installs the common notify handler,
acpi_hotplug_notify_cb(), for PCI root bridges. This causes
acpi_hotplug_notify_cb() to call _OST method with unsupported
error as hotplug.enabled is not set.
To address this issue, introduce hotplug.ignore flag, which
indicates that the scan handler installs its own notify handler by
itself. The ACPI hotplug framework does not install the common
notify handler when this flag is set.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
[rjw: Changed the name of the new flag]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a4d62babf988fe5dfde24437fa135ef147bc7aa0 upstream.
Hardware:
CPU: XLP832,the 64-bit OS
NOR Flash:S29GL128S 128M
Software:
Kernel:2.6.32.41
Filesystem:JFFS2
When writing files, errors appear:
Write len 182 but return retlen 180
Write of 182 bytes at 0x072c815c failed. returned -5, retlen 180
Write len 186 but return retlen 184
Write of 186 bytes at 0x072caff4 failed. returned -5, retlen 184
These errors exist only in 64-bit systems,not in 32-bit systems. After analysis, we
found that the left shift operation is wrong in map_word_load_partial. For instance:
unsigned char buf[3] ={0x9e,0x3a,0xea};
map_bankwidth(map) is 4;
for (i=0; i < 3; i++) {
int bitpos;
bitpos = (map_bankwidth(map)-1-i)*8;
orig.x[0] &= ~(0xff << bitpos);
orig.x[0] |= buf[i] << bitpos;
}
The value of orig.x[0] is expected to be 0x9e3aeaff, but in this situation(64-bit
System) we'll get the wrong value of 0xffffffff9e3aeaff due to the 64-bit sign
extension:
buf[i] is defined as "unsigned char" and the left-shift operation will convert it
to the type of "signed int", so when left-shift buf[i] by 24 bits, the final result
will get the wrong value: 0xffffffff9e3aeaff.
If the left-shift bits are less than 24, then sign extension will not occur. Whereas
the bankwidth of the nor flash we used is 4, therefore this BUG emerges.
Signed-off-by: Pang Xunlei <pang.xunlei@zte.com.cn>
Signed-off-by: Zhang Yi <zhang.yi20@zte.com.cn>
Signed-off-by: Lu Zhongjun <lu.zhongjun@zte.com.cn>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e9b45a19241354daec281d7a785739829b52359 upstream.
On 64 bit systems the test for negative message sizes is bogus as the
size, which may be positive when evaluated as a long, will get truncated
to an int when passed to load_msg(). So a long might very well contain a
positive value but when truncated to an int it would become negative.
That in combination with a small negative value of msg_ctlmax (which will
be promoted to an unsigned type for the comparison against msgsz, making
it a big positive value and therefore make it pass the check) will lead to
two problems: 1/ The kmalloc() call in alloc_msg() will allocate a too
small buffer as the addition of alen is effectively a subtraction. 2/ The
copy_from_user() call in load_msg() will first overflow the buffer with
userland data and then, when the userland access generates an access
violation, the fixup handler copy_user_handle_tail() will try to fill the
remainder with zeros -- roughly 4GB. That almost instantly results in a
system crash or reset.
,-[ Reproducer (needs to be run as root) ]--
| #include <sys/stat.h>
| #include <sys/msg.h>
| #include <unistd.h>
| #include <fcntl.h>
|
| int main(void) {
| long msg = 1;
| int fd;
|
| fd = open("/proc/sys/kernel/msgmax", O_WRONLY);
| write(fd, "-1", 2);
| close(fd);
|
| msgsnd(0, &msg, 0xfffffff0, IPC_NOWAIT);
|
| return 0;
| }
'---
Fix the issue by preventing msgsz from getting truncated by consistently
using size_t for the message length. This way the size checks in
do_msgsnd() could still be passed with a negative value for msg_ctlmax but
we would fail on the buffer allocation in that case and error out.
Also change the type of m_ts from int to size_t to avoid similar nastiness
in other code paths -- it is used in similar constructs, i.e. signed vs.
unsigned checks. It should never become negative under normal
circumstances, though.
Setting msg_ctlmax to a negative value is an odd configuration and should
be prevented. As that might break existing userland, it will be handled
in a separate commit so it could easily be reverted and reworked without
reintroducing the above described bug.
Hardening mechanisms for user copy operations would have catched that bug
early -- e.g. checking slab object sizes on user copy operations as the
usercopy feature of the PaX patch does. Or, for that matter, detect the
long vs. int sign change due to truncation, as the size overflow plugin
of the very same patch does.
[akpm@linux-foundation.org: fix i386 min() warnings]
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Pax Team <pageexec@freemail.hu>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1310a5a99d900ee30b9f171146406bde0c6c2bd4 upstream.
The iterator rbtree_postorder_for_each_entry_safe() relies on pointer
underflow behavior when testing for loop termination. In particular it
expects that
&rb_entry(NULL, type, field)->field
is NULL. But the result of this expression is not defined by a C standard
and some gcc versions (e.g. 4.3.4) assume the above expression can never
be equal to NULL. The net result is an oops because the iteration is not
properly terminated.
Fix the problem by modifying the iterator to avoid pointer underflows.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit de68bab4fa96014cfaa6fcbcdb9750e32969fb86 upstream.
How it's supposed to work:
--------------------------
USB 2.0 Link PM is a lower power state that some newer USB 2.0 devices
support. USB 3.0 devices certified by the USB-IF are required to
support it if they are plugged into a USB 2.0 only port, or a USB 2.0
cable is used. USB 2.0 Link PM requires both a USB device and a host
controller that supports USB 2.0 hardware-enabled LPM.
USB 2.0 Link PM is designed to be enabled once by software, and the host
hardware handles transitions to the L1 state automatically. The premise
of USB 2.0 Link PM is to be able to put the device into a lower power
link state when the bus is idle or the device NAKs USB IN transfers for
a specified amount of time.
...but hardware is broken:
--------------------------
It turns out many USB 3.0 devices claim to support USB 2.0 Link PM (by
setting the LPM bit in their USB 2.0 BOS descriptor), but they don't
actually implement it correctly. This manifests as the USB device
refusing to respond to transfers when it is plugged into a USB 2.0 only
port under the Haswell-ULT/Lynx Point LP xHCI host.
These devices pass the xHCI driver's simple test to enable USB 2.0 Link
PM, wait for the port to enter L1, and then bring it back into L0. They
only start to break when L1 entry is interleaved with transfers.
Some devices then fail to respond to the next control transfer (usually
a Set Configuration). This results in devices never enumerating.
Other mass storage devices (such as a later model Western Digital My
Passport USB 3.0 hard drive) respond fine to going into L1 between
control transfers. They ACK the entry, come out of L1 when the host
needs to send a control transfer, and respond properly to those control
transfers. However, when the first READ10 SCSI command is sent, the
device NAKs the data phase while it's reading from the spinning disk.
Eventually, the host requests to put the link into L1, and the device
ACKs that request. Then it never responds to the data phase of the
READ10 command. This results in not being able to read from the drive.
Some mass storage devices (like the Corsair Survivor USB 3.0 flash
drive) are well behaved. They ACK the entry into L1 during control
transfers, and when SCSI commands start coming in, they NAK the requests
to go into L1, because they need to be at full power.
Not all USB 3.0 devices advertise USB 2.0 link PM support. My Point
Grey USB 3.0 webcam advertises itself as a USB 2.1 device, but doesn't
have a USB 2.0 BOS descriptor, so we don't enable USB 2.0 Link PM. I
suspect that means the device isn't certified.
What do we do about it?
-----------------------
There's really no good way for the kernel to test these devices.
Therefore, the kernel needs to disable USB 2.0 Link PM by default, and
distros will have to enable it by writing 1 to the sysfs file
/sys/bus/usb/devices/../power/usb2_hardware_lpm. Rip out the xHCI Link
PM test, since it's not sufficient to detect these buggy devices, and
don't automatically enable LPM after the device is addressed.
This patch should be backported to kernels as old as 3.11, that
contain the commit a558ccdcc71c7770c5e80c926a31cfe8a3892a09 "usb: xhci:
add USB2 Link power management BESL support". Without this fix, some
USB 3.0 devices will not enumerate or work properly under USB 2.0 ports
on Haswell-ULT systems.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f3f5a0f8cc40b942f4c0ae117df82eeb65f07d4d upstream.
In the spec, the security label attribute id is '80', which means that
it should be bit number 80-64 == 16 in the 3rd word of the bitmap.
Fixes: 4488cc96c581: NFS: Add NFSv4.2 protocol constants
Cc: J. Bruce Fields <bfields@fieldses.org>
Cc: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f44f2a5417b2968a8724b352cc0b2545a6bcb1f4 upstream.
The drain and drain_notify callback were blocked by low level driver
until the draining was complete. Due to this being invoked with big
fat mutex held, others ops like reading timestamp, calling pause, drop
were blocked.
So to fix this we add a new snd_compr_drain_notify() API. This would
be required to be invoked by low level driver when drain or partial
drain has been completed by the DSP. Thus we make the drain and
partial_drain callback as non blocking and driver returns immediately
after notifying DSP. The waiting is done while releasing the lock so
that other ops can go ahead.
[ The commit 917f4b5cba78 was wrongly applied from the preliminary
patch. This commit corrects to the final version.
Sorry for inconvenience! -- tiwai ]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 917f4b5cba78980a527098a910d94139d3e82c8d upstream.
The drain and drain_notify callback were blocked by low level driver untill the
draining was complete. Due to this being invoked with big fat mutex held, others
ops like reading timestamp, calling pause, drop were blocked.
So to fix this we add a new snd_compr_drain_notify() API. This would be required
to be invoked by low level driver when drain or partial drain has been completed
by the DSP. Thus we make the drain and partial_drain callback as non blocking
and driver returns immediately after notifying DSP.
The waiting is done while relasing the lock so that other ops can go ahead.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d049f74f2dbe71354d43d393ac3a188947811348 upstream.
The get_dumpable() return value is not boolean. Most users of the
function actually want to be testing for non-SUID_DUMP_USER(1) rather than
SUID_DUMP_DISABLE(0). The SUID_DUMP_ROOT(2) is also considered a
protected state. Almost all places did this correctly, excepting the two
places fixed in this patch.
Wrong logic:
if (dumpable == SUID_DUMP_DISABLE) { /* be protective */ }
or
if (dumpable == 0) { /* be protective */ }
or
if (!dumpable) { /* be protective */ }
Correct logic:
if (dumpable != SUID_DUMP_USER) { /* be protective */ }
or
if (dumpable != 1) { /* be protective */ }
Without this patch, if the system had set the sysctl fs/suid_dumpable=2, a
user was able to ptrace attach to processes that had dropped privileges to
that user. (This may have been partially mitigated if Yama was enabled.)
The macros have been moved into the file that declares get/set_dumpable(),
which means things like the ia64 code can see them too.
CVE-2013-2929
Reported-by: Vasily Kulikov <segoon@openwall.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea8117478918a4734586d35ff530721b682425be upstream.
Mike reported that commit 7d1a9417 ("x86: Use generic idle loop")
regressed several workloads and caused excessive reschedule
interrupts.
The patch in question failed to notice that the x86 code had an
inverted sense of the polling state versus the new generic code (x86:
default polling, generic: default !polling).
Fix the two prominent x86 mwait based idle drivers and introduce a few
new generic polling helpers (fixing the wrong smp_mb__after_clear_bit
usage).
Also switch the idle routines to using tif_need_resched() which is an
immediate TIF_NEED_RESCHED test as opposed to need_resched which will
end up being slightly different.
Reported-by: Mike Galbraith <bitbucket@online.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: lenb@kernel.org
Cc: tglx@linutronix.de
Link: http://lkml.kernel.org/n/tip-nc03imb0etuefmzybzj7sprf@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 01ba16d6ec85a1ec4669c75513a76b61ec53ee50 ]
On receiving a packet too big icmp error we update the expire value by
calling rt6_update_expires. This function uses dst_set_expires which is
implemented that it can only reduce the expiration value of the dst entry.
If we insert new routing non-expiry information into the ipv6 fib where
we already have a matching rt6_info we only clear the RTF_EXPIRES flag
in rt6i_flags and leave the dst.expires value as is.
When new mtu information arrives for that cached dst_entry we again
call dst_set_expires. This time it won't update the dst.expire value
because we left the dst.expire value intact from the last update. So
dst_set_expires won't touch dst.expires.
Fix this by resetting dst.expires when clearing the RTF_EXPIRE flag.
dst_set_expires checks for a zero expiration and updates the
dst.expires.
In the past this (not updating dst.expires) was necessary because
dst.expire was placed in a union with the dst_entry *from reference
and rt6_clean_expires did assign NULL to it. This split happend in
ecd9883724b78cc72ed92c98bcb1a46c764fff21 ("ipv6: fix race condition
regarding dst->expires and dst->from").
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Reported-by: Valentijn Sessink <valentyn@blub.net>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Valentijn Sessink <valentyn@blub.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Negative message lengths make no sense -- so don't do negative queue
lenghts or identifier counts. Prevent them from getting negative.
Also change the underlying data types to be unsigned to avoid hairy
surprises with sign extensions in cases where those variables get
evaluated in unsigned expressions with bigger data types, e.g size_t.
In case a user still wants to have "unlimited" sizes she could just use
INT_MAX instead.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Two fixes:
- Fix 'NMI handler took too long to run' false positives
[ Genuine NMI overhead speedups will come for v3.13, this commit
only fixes a measurement bug ]
- Fix perf ring-buffer missed barrier causing (rare) ring-buffer data
corruption on ppc64"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix NMI measurements
perf: Fix perf ring buffer memory ordering
|
|
this_cpu_sub() is implemented as negation and addition.
This patch casts the adjustment to the counter type before negation to
sign extend the adjustment. This helps in cases where the counter type
is wider than an unsigned adjustment. An alternative to this patch is
to declare such operations unsupported, but it seemed useful to avoid
surprises.
This patch specifically helps the following example:
unsigned int delta = 1
preempt_disable()
this_cpu_write(long_counter, 0)
this_cpu_sub(long_counter, delta)
preempt_enable()
Before this change long_counter on a 64 bit machine ends with value
0xffffffff, rather than 0xffffffffffffffff. This is because
this_cpu_sub(pcp, delta) boils down to this_cpu_add(pcp, -delta),
which is basically:
long_counter = 0 + 0xffffffff
Also apply the same cast to:
__this_cpu_sub()
__this_cpu_sub_return()
this_cpu_sub_return()
All percpu_test.ko passes, especially the following cases which
previously failed:
l -= ui_one;
__this_cpu_sub(long_counter, ui_one);
CHECK(l, long_counter, -1);
l -= ui_one;
this_cpu_sub(long_counter, ui_one);
CHECK(l, long_counter, -1);
CHECK(l, long_counter, 0xffffffffffffffff);
ul -= ui_one;
__this_cpu_sub(ulong_counter, ui_one);
CHECK(ul, ulong_counter, -1);
CHECK(ul, ulong_counter, 0xffffffffffffffff);
ul = this_cpu_sub_return(ulong_counter, ui_one);
CHECK(ul, ulong_counter, 2);
ul = __this_cpu_sub_return(ulong_counter, ui_one);
CHECK(ul, ulong_counter, 1);
Signed-off-by: Greg Thelen <gthelen@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The PPC64 people noticed a missing memory barrier and crufty old
comments in the perf ring buffer code. So update all the comments and
add the missing barrier.
When the architecture implements local_t using atomic_long_t there
will be double barriers issued; but short of introducing more
conditional barrier primitives this is the best we can do.
Reported-by: Victor Kaplansky <victork@il.ibm.com>
Tested-by: Victor Kaplansky <victork@il.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: michael@ellerman.id.au
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: anton@samba.org
Cc: benh@kernel.crashing.org
Link: http://lkml.kernel.org/r/20131025173749.GG19466@laptop.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target pending fixes for v3.12-rc7.
This includes a number of EXTENDED_COPY related fixes as a result of
Thomas and Doug's continuing testing and feedback.
Also included is an important vhost/scsi fix that addresses a long
standing issue where the 'write' parameter for get_user_pages_fast()
was incorrectly set for virtio-scsi WRITEs -> DMA_TO_DEVICE, and not
for virtio-scsi READs -> DMA_FROM_DEVICE.
This resulted in random userspace segfaults and other unpleasantness
on KVM host, and unfortunately has been an issue since the initial
merge of vhost/scsi in v3.6. This patch is CC'ed to stable, along
with two other less critical items"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
vhost/scsi: Fix incorrect usage of get_user_pages_fast write parameter
target/pscsi: fix return value check
target: Fail XCOPY for non matching source + destination block_size
target: Generate failure for XCOPY I/O with non-zero scsi_status
target: Add missing XCOPY I/O operation sense_buffer
iser-target: check device before dereferencing its variable
target: Return an error for WRITE SAME with ANCHOR==1
target: Fix assignment of LUN in tracepoints
target: Reject EXTENDED_COPY when emulate_3pc is disabled
target: Allow non zero ListID in EXTENDED_COPY parameter list
target: Make target_do_xcopy failures return INVALID_PARAMETER_LIST
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband bugfix from Roland Dreier:
"Disable not-quite-ready userspace ABI for IB flow steering"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Temporarily disable create_flow/destroy_flow uverbs
|
|
Pull networking fixes from David Miller:
"Sorry I let so much accumulate, I was in Buffalo and wanted a few
things to cook in my tree for a while before sending to you. Anyways,
it's a lot of little things as usual at this stage in the game"
1) Make bonding MAINTAINERS entry reflect reality, from Andy
Gospodarek.
2) Fix accidental sock_put() on timewait mini sockets, from Eric
Dumazet.
3) Fix crashes in l2tp due to mis-handling of ipv4 mapped ipv6
addresses, from François CACHEREUL.
4) Fix heap overflow in __audit_sockaddr(), from the eagle eyed Dan
Carpenter.
5) tcp_shifted_skb() doesn't take handle FINs properly, from Eric
Dumazet.
6) SFC driver bug fixes from Ben Hutchings.
7) Fix TX packet scheduling wedge after channel change in ath9k driver,
from Felix Fietkau.
8) Fix user after free in BPF JIT code, from Alexei Starovoitov.
9) Source address selection test is reversed in
__ip_route_output_key(), fix from Jiri Benc.
10) VLAN and CAN layer mis-size netlink attributes, from Marc
Kleine-Budde.
11) Fix permission checks in sysctls to use current_euid() instead of
current_uid(). From Eric W Biederman.
12) IPSEC policies can go away while a timer is still pending for them,
add appropriate ref-counting to fix, from Steffen Klassert.
13) Fix mis-programming of FDR and RMCR registers on R8A7740 sh_eth
chips, from Nguyen Hong Ky and Simon Horman.
14) MLX4 forgets to DMA unmap pages on RX, fix from Amir Vadai.
15) IPV6 GRE tunnel MTU upper limit is miscalculated, from Oussama
Ghorbel.
16) Fix typo in fq_change(), we were assigning "initial quantum" to
"quantum". From Eric Dumazet.
17) Set a more appropriate sk_pacing_rate for non-TCP sockets, otherwise
FQ packet scheduler does not pace those flows properly. Also from
Eric Dumazet.
18) rtlwifi miscalculates packet pointers, from Mark Cave-Ayland.
19) l2tp_xmit_skb() can be called from process context, not just softirq
context, so we must always make sure to BH disable around it. From
Eric Dumazet.
20) On qdisc reset, we forget to purge the RB tree of SKBs in netem
packet scheduler. From Stephen Hemminger.
21) Fix info leak in farsync WAN driver ioctl() handler, from Dan
Carpenter and Salva Peiró.
22) Fix PHY reset and other issues in dm9000 driver, from Nikita
Kiryanov and Michael Abbott.
23) When hardware can do SCTP crc32 checksums, we accidently don't
disable the csum offload when IPSEC transformations have been
applied. From Fan Du and Vlad Yasevich.
24) Tail loss probing in TCP leaves the socket in the wrong congestion
avoidance state. From Yuchung Cheng.
25) In CPSW driver, enable NAPI before interrupts are turned on, from
Markus Pargmann.
26) Integer underflow and dual-assignment in YAM hamradio driver, from
Dan Carpenter.
27) If we are going to mangle a packet in tcp_set_skb_tso_segs() we must
unclone it. This fixes various hard to track down crashes in
drivers where the SKBs ->gso_segs was changing right from underneath
the driver during TX queueing. From Eric Dumazet.
28) Fix the handling of VLAN IDs, and in particular the special IDs 0
and 4095, in the bridging layer. From Toshiaki Makita.
29) Another info leak, this time in wanxl WAN driver, from Salva Peiró.
30) Fix race in socket credential passing, from Daniel Borkmann.
31) WHen NETLABEL is disabled, we don't validate CIPSO packets properly,
from Seif Mazareeb.
32) Fix identification of fragmented frames in ipv4/ipv6 UDP
Fragmentation Offload output paths, from Jiri Pirko.
33) Virtual Function fixes in bnx2x driver from Yuval Mintz and Ariel
Elior.
34) When we removed the explicit neighbour pointer from ipv6 routes a
slight regression was introduced for users such as IPVS, xt_TEE, and
raw sockets. We mix up the users requested destination address with
the routes assigned nexthop/gateway. From Julian Anastasov and
Simon Horman.
35) Fix stack overruns in rt6_probe(), the issue is that can end up
doing two full packet xmit paths at the same time when emitting
neighbour discovery messages. From Hannes Frederic Sowa.
36) davinci_emac driver doesn't handle IFF_ALLMULTI correctly, from
Mariusz Ceier.
37) Make sure to set TCP sk_pacing_rate after the first legitimate RTT
sample, from Neal Cardwell.
38) Wrong netlink attribute passed to xfrm_replay_verify_len(), from
Steffen Klassert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (152 commits)
ax88179_178a: Add VID:DID for Samsung USB Ethernet Adapter
ax88179_178a: Correct the RX error definition in RX header
Revert "bridge: only expire the mdb entry when query is received"
tcp: initialize passive-side sk_pacing_rate after 3WHS
davinci_emac.c: Fix IFF_ALLMULTI setup
mac802154: correct a typo in ieee802154_alloc_device() prototype
ipv6: probe routes asynchronous in rt6_probe
netfilter: nf_conntrack: fix rt6i_gateway checks for H.323 helper
ipv6: fill rt6i_gateway with nexthop address
ipv6: always prefer rt6i_gateway if present
bnx2x: Set NETIF_F_HIGHDMA unconditionally
bnx2x: Don't pretend during register dump
bnx2x: Lock DMAE when used by statistic flow
bnx2x: Prevent null pointer dereference on error flow
bnx2x: Fix config when SR-IOV and iSCSI are enabled
bnx2x: Fix Coalescing configuration
bnx2x: Unlock VF-PF channel on MAC/VLAN config error
bnx2x: Prevent an illegal pointer dereference during panic
bnx2x: Fix Maximum CoS estimation for VFs
drivers: net: cpsw: fix kernel warn during iperf test with interrupt pacing
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The pending last-minute ASoC fixes, all of which are driver-local
(tlv320aic3x, rcar, pcm1681, pcm1792a, omap, fsl) and should be pretty
safe to apply"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: Add MAINTAINERS entry for dmaengine helpers
ASoC: pcm1792a: Fix max_register setting
ASoC: pcm1681: Fix max_register setting
ASoC: pcm1681: Fix max_register setting
ASoC: rcar: fixup generation checker
ASoC: tlv320aic3x: Connect 'Left Line1R Mux' and 'Right Line1L Mux'
ASoC: fsl: imx-ssi: fix probe on imx31
ASoC: omap: Fix incorrect ARM dependency
ASoC: fsl: Fix sound on mx31moboard
ASoC: fsl_ssi: Fix irq_of_parse_and_map() return value check
|
|
Pull drm fixes from Dave Airlie:
"Travelling slowed down getting these out.
Two vmwgfx fixes, a radeon revert to avoid a regression, i915 fixes,
and some ioctl sizing issues fixed with 32 on 64"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/audio: don't set speaker allocation on DCE4+
drm/radeon: rework audio option
drm/radeon/audio: don't set speaker allocation on DCE3.2
drm/radeon: make missing smc ucode non-fatal (CI)
drm/radeon: make missing smc ucode non-fatal (r7xx-SI)
drm/radeon/uvd: revert lower msg&fb buffer requirements on UVD3
drm/radeon: stop the leaks in cik_ib_test
drm/radeon/atom: workaround vbios bug in transmitter table on rs780
drm/i915: Disable GGTT PTEs on GEN6+ suspend
drm/i915: Make PTE valid encoding optional
drm: Pad drm_mode_get_connector to 64-bit boundary
drm: Prevent overwriting from userspace underallocating core ioctl structs
drm/vmwgfx: Don't kill clients on VT switch
drm/vmwgfx: Don't put resources with invalid id's on lru list
drm/i915: disable LVDS clock gating on CPT v2
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Just an lvds clock gating fix and a pte clearing hack for hsw to avoid
memory corruption when hibernating - something doesn't seem to switch off
properly, we're still investigating.
* tag 'drm-intel-fixes-2013-10-21' of git://people.freedesktop.org/~danvet/drm-intel: (96 commits)
drm/i915: Disable GGTT PTEs on GEN6+ suspend
drm/i915: Make PTE valid encoding optional
drm/i915: disable LVDS clock gating on CPT v2
|
|
This has no other impact than a cosmetic one.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure rt6i_gateway contains nexthop information in
all routes returned from lookup or when routes are directly
attached to skb for generated ICMP packets.
The effect of this patch should be a faster version of
rt6_nexthop() and the consideration of local addresses as
nexthop.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In v3.9 6fd6ce2056de2709 ("ipv6: Do not depend on rt->n in
ip6_finish_output2()." changed the behaviour of ip6_finish_output2()
such that the recently introduced rt6_nexthop() is used
instead of an assigned neighbor.
As rt6_nexthop() prefers rt6i_gateway only for gatewayed
routes this causes a problem for users like IPVS, xt_TEE and
RAW(hdrincl) if they want to use different address for routing
compared to the destination address.
Another case is when redirect can create RTF_DYNAMIC
route without RTF_GATEWAY flag, we ignore the rt6i_gateway
in rt6_nexthop().
Fix the above problems by considering the rt6i_gateway if
present, so that traffic routed to address on local subnet is
not wrongly diverted to the destination address.
Thanks to Simon Horman and Phil Oester for spotting the
problematic commit.
Thanks to Hannes Frederic Sowa for his review and help in testing.
Reported-by: Phil Oester <kernel@linuxace.com>
Reported-by: Mark Brooks <mark@loadbalancer.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The create_flow/destroy_flow uverbs and the associated extensions to
the user-kernel verbs ABI are under review and are too experimental to
freeze at this point.
So userspace is not exposed to experimental features and an uinstable
ABI, temporarily disable this for v3.12 (with a Kconfig option behind
staging to reenable it if desired).
The feature will be enabled after proper cleanup for v3.13.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://marc.info/?i=cover.1381351016.git.ydroneaud@opteya.com
Link: http://marc.info/?i=cover.1381177342.git.ydroneaud@opteya.com
[ Add a Kconfig option to reenable these verbs. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
When CONFIG_NETLABEL is disabled, the cipso_v4_validate() function could loop
forever in the main loop if opt[opt_iter +1] == 0, this will causing a kernel
crash in an SMP system, since the CPU executing this function will
stall /not respond to IPIs.
This problem can be reproduced by running the IP Stack Integrity Checker
(http://isic.sourceforge.net) using the following command on a Linux machine
connected to DUT:
"icmpsic -s rand -d <DUT IP address> -r 123456"
wait (1-2 min)
Signed-off-by: Seif Mazareeb <seif@marvell.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- intel_pstate fix for misbehavior after system resume if sysfs
attributes are set in a specific way before the corresponding suspend
from Dirk Brandewie.
- A recent intel_pstate fix has no effect if unsigned long is 32-bit,
so fix it up to cover that case as well.
- The s3c64xx cpufreq driver was not updated when the index field of
struct cpufreq_frequency_table was replaced with driver_data, so
update it now. From Charles Keepax.
- The Kconfig help text for ACPI_BUTTON still refers to
/proc/acpi/event that has been dropped recently, so modify it to
remove that reference. From Krzysztof Mazur.
- A Lan Tianyu's change adds a missing mutex unlock to an error code
path in acpi_resume_power_resources().
- Some code related to ACPI power resources, whose very purpose is
questionable to put it lightly, turns out to cause problems to happen
during testing on real systems, so remove it completely (we may
revisit that in the future if there's a compelling enough reason).
From Rafael J Wysocki and Aaron Lu.
* tag 'pm+acpi-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Drop two functions that are not used any more
ATA / ACPI: remove power dependent device handling
cpufreq: s3c64xx: Rename index to driver_data
ACPI / power: Drop automaitc resume of power resource dependent devices
intel_pstate: Fix type mismatch warning
cpufreq / intel_pstate: Fix max_perf_pct on resume
ACPI: remove /proc/acpi/event from ACPI_BUTTON help
ACPI / power: Release resource_lock after acpi_power_get_state() return error
|
|
|
|
Pavel Roskin reported that DRM_IOCTL_MODE_GETCONNECTOR was overwritting
the 4 bytes beyond the end of its structure with a 32-bit userspace
running on a 64-bit kernel. This is due to the padding gcc inserts as
the drm_mode_get_connector struct includes a u64 and its size is not a
natural multiple of u64s.
64-bit kernel:
sizeof(drm_mode_get_connector)=80, alignof=8
sizeof(drm_mode_get_encoder)=20, alignof=4
sizeof(drm_mode_modeinfo)=68, alignof=4
32-bit userspace:
sizeof(drm_mode_get_connector)=76, alignof=4
sizeof(drm_mode_get_encoder)=20, alignof=4
sizeof(drm_mode_modeinfo)=68, alignof=4
Fortuituously we can insert explicit padding to the tail of our
structures without breaking ABI.
Reported-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
We cap bitrate at YAM_MAXBITRATE in yam_ioctl(), but it could also be
negative. I don't know the impact of using a negative bitrate but let's
prevent it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dst->xfrm is conditionally defined. Provide accessor funtion that
is always available.
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 3.12-rc6
The largest change here is a bunch of new device ids for the option
USB serial driver for new Huawei devices. Other than that, just some
small bug fixes for issues that people have reported (run-time and
build-time), nothing major"
* tag 'usb-3.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: usb_phy_gen: refine conditional declaration of usb_nop_xceiv_register
usb: misc: usb3503: Fix compile error due to incorrect regmap depedency
usb/chipidea: fix oops on memory allocation failure
usb-storage: add quirk for mandatory READ_CAPACITY_16
usb: serial: option: blacklist Olivetti Olicard200
USB: quirks: add touchscreen that is dazzeled by remote wakeup
Revert "usb: musb: gadget: fix otg active status flag"
USB: quirks.c: add one device that cannot deal with suspension
USB: serial: option: add support for Inovia SEW858 device
USB: serial: ti_usb_3410_5052: add Abbott strip port ID to combined table as well.
USB: support new huawei devices in option.c
usb: musb: start musb on the udc side, too
xhci: Fix spurious wakeups after S5 on Haswell
xhci: fix write to USB3_PSSEN and XUSB2PRM pci config registers
xhci: quirk for extra long delay for S4
xhci: Don't enable/disable RWE on bus suspend/resume.
|
|
Commit 3fa4d734 (usb: phy: rename nop_usb_xceiv => usb_phy_gen_xceiv)
changed the conditional around the declaration of usb_nop_xceiv_register
from
#if defined(CONFIG_NOP_USB_XCEIV) ||
(defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE))
to
#if IS_ENABLED(CONFIG_NOP_USB_XCEIV)
While that looks the same, it is semantically different. The first expression
is true if CONFIG_NOP_USB_XCEIV is built as module and if the including
code is built as module. The second expression is true if code depending on
CONFIG_NOP_USB_XCEIV if built as module or into the kernel.
As a result, the arm:allmodconfig build fails with
arch/arm/mach-omap2/built-in.o: In function `omap3_evm_init':
arch/arm/mach-omap2/board-omap3evm.c:703: undefined reference to
`usb_nop_xceiv_register'
Fix the problem by reverting to the old conditional.
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Two functions defined in device_pm.c, acpi_dev_pm_add_dependent()
and acpi_dev_pm_remove_dependent(), have no callers and may be
dropped, so drop them.
Moreover, they are the only functions adding entries to and removing
entries from the power_dependent list in struct acpi_device, so drop
that list too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 3812c8c8f395 ("mm: memcg: do not trap chargers with full
callstack on OOM") assumed that only a few places that can trigger a
memcg OOM situation do not return VM_FAULT_OOM, like optional page cache
readahead. But there are many more and it's impractical to annotate
them all.
First of all, we don't want to invoke the OOM killer when the failed
allocation is gracefully handled, so defer the actual kill to the end of
the fault handling as well. This simplifies the code quite a bit for
added bonus.
Second, since a failed allocation might not be the abrupt end of the
fault, the memcg OOM handler needs to be re-entrant until the fault
finishes for subsequent allocation attempts. If an allocation is
attempted after the task already OOMed, allow it to bypass the limit so
that it can quickly finish the fault and invoke the OOM killer.
Reported-by: azurIt <azurit@pobox.sk>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
