| Age | Commit message (Collapse) | Author |
|---|
|
The check_fb() hook may need the fb event information to
do something. For example, people may use it to delay
some time before enabling a backlight as some special panel
requires. To support this, this patch adds a field of
struct fb_event in the structure backlight_device and sets
the field in the fb notifier handler of the backlight driver.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
|
|
Add FB_EARLY_EVENT_BLANK and FB_R_EARLY_EVENT_BLANK event mode supports.
first, fb_notifier_call_chain() is called with FB_EARLY_EVENT_BLANK and
fb_blank() of specific fb driver is called and then
fb_notifier_call_chain() is called with FB_EVENT_BLANK again at
fb_blank(). and if fb_blank() was failed then fb_nitifier_call_chain()
would be called with FB_R_EARLY_EVENT_BLANK to revert the previous
effects.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(cherry picked from commit bf05929f41d6c3c79ec1961d90d808a634f09dd9)
|
|
When hotplug, user will close and reopen the device, shutdown()
will be called, MCLK will be disabled, then I2C access to wm8962
will have issue. so the drive didn't switch to headphone.
Move the clk enable and disable to codec driver to fix this issue.
Signed-off-by: Shengjiu Wang <b02247@freescale.com>
|
|
[backport of net-next 6d0bfe22611602f36617bc7aa2ffa1bbb2f54c67]
This adds the ability to send ICMPv6 echo requests without a
raw socket. The equivalent ability for ICMPv4 was added in
2011.
Instead of having separate code paths for IPv4 and IPv6, make
most of the code in net/ipv4/ping.c dual-stack and only add a
few IPv6-specific bits (like the protocol definition) to a new
net/ipv6/ping.c. Hopefully this will reduce divergence and/or
duplication of bugs in the future.
Caveats:
- Setting options via ancillary data (e.g., using IPV6_PKTINFO
to specify the outgoing interface) is not yet supported.
- There are no separate security settings for IPv4 and IPv6;
everything is controlled by /proc/net/ipv4/ping_group_range.
- The proc interface does not yet display IPv6 ping sockets
properly.
Tested with a patched copy of ping6 and using raw socket calls.
Compiles and works with all of CONFIG_IPV6={n,m,y}.
Change-Id: Ia359af556021344fc7f890c21383aadf950b6498
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[lorenzo@google.com: backported to 3.0]
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
|
|
functions
[net-next commit b7ef213ef65256168df83ddfbb8131ed9adc10f9]
__ipv6_addr_needs_scope_id checks if an ipv6 address needs to supply
a 'sin6_scope_id != 0'. 'sin6_scope_id != 0' was enforced in case
of link-local addresses. To support interface-local multicast these
checks had to be enhanced and are now consolidated into these new helper
functions.
v2:
a) migrated to struct ipv6_addr_props
v3:
a) reverted changes for ipv6_addr_props
b) test for address type instead of comparing scope
v4:
a) unchanged
Change-Id: Id6fc54cec61f967928e08a9eba4f857157d973a3
Suggested-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[ Upstream commit 5a3da1fe9561828d0ca7eca664b16ec2b9bf0055 ]
This patch introduces a constant limit of the fragment queue hash
table bucket list lengths. Currently the limit 128 is choosen somewhat
arbitrary and just ensures that we can fill up the fragment cache with
empty packets up to the default ip_frag_high_thresh limits. It should
just protect from list iteration eating considerable amounts of cpu.
If we reach the maximum length in one hash bucket a warning is printed.
This is implemented on the caller side of inet_frag_find to distinguish
between the different users of inet_fragment.c.
I dropped the out of memory warning in the ipv4 fragment lookup path,
because we already get a warning by the slab allocator.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jesper Dangaard Brouer <jbrouer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c7ac8679bec9397afe8918f788cbcef88c38da54 upstream.
The message size allocated for rtnl ifinfo dumps was limited to
a single page. This is not enough for additional interface info
available with devices that support SR-IOV and caused a bug in
which VF info would not be displayed if more than approximately
40 VFs were created per interface.
Implement a new function pointer for the rtnl_register service that will
calculate the amount of data required for the ifinfo dump and allocate
enough data to satisfy the request.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Hi, Jens,
If you recall, I posted an RFC patch for this back in July of last year:
http://lkml.org/lkml/2010/7/13/279
The basic problem is that a process can issue a never-ending stream of
async direct I/Os to the same sector on a device, thus starving out
other I/O in the system (due to the way the alias handling works in both
cfq and deadline). The solution I proposed back then was to start
dispatching from the fifo after a certain number of aliases had been
dispatched. Vivek asked why we had to treat aliases differently at all,
and I never had a good answer. So, I put together a simple patch which
allows aliases to be added to the rb tree (it adds them to the right,
though that doesn't matter as the order isn't guaranteed anyway). I
think this is the preferred solution, as it doesn't break up time slices
in CFQ or batches in deadline. I've tested it, and it does solve the
starvation issue. Let me know what you think.
Cheers,
Jeff
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Add IR char driver,mx6_ir driver,epit driver and update configuration
for support IR.
Signed-off-by: Ke Qinghua <qinghua.ke@freescale.com>
|
|
Add EPIT driver
Signed-off-by: Ke Qinghua <qinghua.ke@freescale.com>
|
|
imx_3.0.35_android
|
|
This reverts commit 881e21c1275dcc40ccd63fb4fa46b990eeb4fb00.
With the commit 881e21c1 and 7b60e285, the system will hang when do suspend
and resume stress test continuouly while run edpc test in the background.
Revert it now and revisit it later.
Signed-off-by: Robby Cai <R63905@freescale.com>
|
|
imx_3.0.35_android
|
|
The display MIX can be power gated when EPDC, PXP and LCDIF are all inactive.
This will save around 1.5mW-1.8mW of power in system IDLE mode.
Need to re-initialize the EPDC and PXP whenever the display MIX is
powered up as all the register state is lost when the display MIX is
power gated.
Signed-off-by: Ranjani Vaidyanathan <ra5478@freescale.com>
|
|
imx_3.0.35_android
Conflicts:
arch/arm/mach-mx6/Kconfig
arch/arm/mach-mx6/board-mx6q_arm2.c
arch/arm/mach-mx6/board-mx6q_arm2.h
arch/arm/mach-mx6/board-mx6q_hdmidongle.c
arch/arm/mach-mx6/board-mx6q_sabreauto.c
arch/arm/mach-mx6/board-mx6q_sabreauto.h
arch/arm/mach-mx6/board-mx6q_sabrelite.c
arch/arm/mach-mx6/board-mx6q_sabresd.c
arch/arm/mach-mx6/board-mx6q_sabresd.h
arch/arm/mach-mx6/clock.c
arch/arm/mach-mx6/pcie.c
arch/arm/plat-mxc/include/mach/iomux-mx6q.h
arch/arm/plat-mxc/include/mach/pcie.h
drivers/dma/imx-sdma.c
drivers/input/touchscreen/egalax_ts.c
drivers/media/video/mxc/capture/csi_v4l2_capture.c
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_os.c
drivers/mxc/mlb/mxc_mlb150.c
drivers/mxc/thermal/thermal.c
drivers/net/fec.c
drivers/usb/host/ehci-arc.c
drivers/video/mxc/mxc_ipuv3_fb.c
include/linux/fec.h
sound/soc/imx/imx-wm8962.c
|
|
Add a command line option to route the ENET interrupts to the GPIO_1_6.
To route the ENET interrupts to GPIO_6 add "enet_gpio_6" to the
kernel command line.
Also remove the CONFIG option (MX6_ENET_IRQ_TO_GPIO).
This commit should be applied on top of following commits:
72c86f0b9a953e91bb1ed31021b71f337050bc28
808863866d2c17aeb3e70a7fcd094bd96db4b601
bae4d40849f3acdd9663f5a0857c9415ed7e6d5d
Signed-off-by: Ranjani Vaidyanathan <ra5478@freescale.com>
|
|
This file could be included in user-space application while uint is not quite
standard type. This patch changed to unsigned int to avoid to include specific
header file. This is requested from mm team.
Signed-off-by: Robby Cai <R63905@freescale.com>
(cherry picked from commit 318a325b8c19d1ba7c1451797da5a161e787c64d)
|
|
The old req_pair() constrained that only Pair B could afford 6 channels,
while actually not. So rewrite it to be more flexible.
Acked-by: Wang Shengjiu <b02247@freescale.com>
Signed-off-by: Nicolin Chen <b42378@freescale.com>
(cherry picked from commit adbc9dbba6ee46c05c0878a8e3bab118981d62c7)
|
|
Added missing clock and revised the clock map for v2
Acked-by: Wang Shengjiu <b02247@freescale.com>
Signed-off-by: Nicolin Chen <b42378@freescale.com>
(cherry picked from commit c7e1b9af10cb579efaf7c4644170f6f8bee401e2)
|
|
It is the same issue with ENGR00217721, and it is also needed
for normal usb case.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
This patch adds basic 16-bit generic data support for SMFC channel.
Although we didn't verify capturing frames with 16-bit generic
data, this could be a good starting point for developers to go on
with.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
|
|
imx_3.0.35_android
|
|
can_get_echo_skb() is usually called in the TX complete handler.
The stats->tx_packets and stats->tx_bytes should be updated there, too.
This patch simplifies to figure out the size of the sent CAN frame.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
can_get_echo_skb() is usually called in the TX complete handler.
The stats->tx_packets and stats->tx_bytes should be updated there, too.
This patch simplifies to figure out the size of the sent CAN frame.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
All of the interrupts from the ENET block are not routed to
the GPC block. Hence ENET interrupts are not able to wake
up the SOC when the system is in WAIT mode. And the ENET
interrupt gets serviced only when another interrupt causes
the SOC to exit WAIT mode. This impacts the ENET performance.
To fix the issue two options:
1. Route the ENET interrupt to a GPIO. Need to enable the
CONFIG_MX6_ENET_IRQ_TO_GPIO in the config.
2. If the GPIO mechanism cannot be used and is not enabled
by the above mentioned config, the patch will disable entry
to WAIT mode until ENET clock is active. When the ENET clock
is disabled, WAIT mode will be automatically enetered.
Signed-off-by: Ranjani Vaidyanathan <ra5478@freescale.com>
|
|
Use circle buf to replace old ringbuf mechanism.
Change to use circle buffer in read, write, rx isr and tx isr functions.
In first design of MLB, it's using it's own mechanism to manage ring
buffer, like in mxc_mlb.c.
And then, I saw that kernel already had a serials of circ buffer macros
which can be used to manage ring buffers.
This patch is to use circle buffer macros to manage mlb internal ring
buffers.
For detail of circle buffers, you can refer to
linux-2.6-imx/Documentation/circular-buffers.txt.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
Use circle buf to replace old ringbuf mechanism.
Change to use circle buffer in read, write, rx isr and tx isr functions.
In first design of MLB, it's using it's own mechanism to manage ring
buffer, like in mxc_mlb.c.
And then, I saw that kernel already had a serials of circ buffer macros
which can be used to manage ring buffers.
This patch is to use circle buffer macros to manage mlb internal ring
buffers.
For detail of circle buffers, you can refer to
linux-2.6-imx/Documentation/circular-buffers.txt.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
All of the interrupts from the ENET block are not routed to
the GPC block. Hence ENET interrupts are not able to wake
up the SOC when the system is in WAIT mode. And the ENET
interrupt gets serviced only when another interrupt causes
the SOC to exit WAIT mode. This impacts the ENET performance.
To fix the issue two options:
1. Route the ENET interrupt to a GPIO. Need to enable the
CONFIG_MX6_ENET_IRQ_TO_GPIO in the config.
2. If the GPIO mechanism cannot be used and is not enabled
by the above mentioned config, the patch will disable entry
to WAIT mode until ENET clock is active. When the ENET clock
is disabled, WAIT mode will be automatically enetered.
Signed-off-by: Ranjani Vaidyanathan <ra5478@freescale.com>
|
|
imx_3.0.35_android
|
|
During the read of NOR, the kernel actually calls the inline_map_copy_from()
to read the data out. And inline_map_copy_from() will use the memcpy_fromio()
to do the real job.
The memcpy_fromio macro maps _memcpy_fromio() in the current code.
But the _memcpy_fromio() will use readb() to do the copy work one byte
by one byte. This makes the read performance of NOR very slow(about 2~3MB/s).
A similiar discussion could be found in:
http://lists.infradead.org/pipermail/linux-arm-kernel/2009-November/003860.html
This patch replace the memcpy_fromio with memcpy which is optimized by the
kernel.
The following is the result from mtd_speedtest with M29W256GL7AN6E:
=================================================
mtd_speedtest: MTD device: 2
mtd_speedtest: not NAND flash, assume page size is 512 bytes.
mtd_speedtest: MTD device size 4194304, eraseblock size 131072, page size 512,
count of eraseblocks 32, pages per eraseblock 256, OOB size 0
mtd_speedtest: testing eraseblock write speed
mtd_speedtest: eraseblock write speed is 845 KiB/s
mtd_speedtest: testing eraseblock read speed
mtd_speedtest: eraseblock read speed is 19504 KiB/s
mtd_speedtest: testing page write speed
mtd_speedtest: page write speed is 845 KiB/s
mtd_speedtest: testing page read speed
mtd_speedtest: page read speed is 19140 KiB/s
mtd_speedtest: testing 2 page write speed
mtd_speedtest: 2 page write speed is 846 KiB/s
mtd_speedtest: testing 2 page read speed
mtd_speedtest: 2 page read speed is 19320 KiB/s
mtd_speedtest: Testing erase speed
mtd_speedtest: erase speed is 233 KiB/s
mtd_speedtest: Testing 2x multi-block erase speed
mtd_speedtest: 2x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 4x multi-block erase speed
mtd_speedtest: 4x multi-block erase speed is 224 KiB/s
mtd_speedtest: Testing 8x multi-block erase speed
mtd_speedtest: 8x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 16x multi-block erase speed
mtd_speedtest: 16x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 32x multi-block erase speed
mtd_speedtest: 32x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 64x multi-block erase speed
mtd_speedtest: 64x multi-block erase speed is 224 KiB/s
mtd_speedtest: finished
=================================================
Signed-off-by: Huang Shijie <b32955@freescale.com>
|
|
During the read of NOR, the kernel actually calls the inline_map_copy_from()
to read the data out. And inline_map_copy_from() will use the memcpy_fromio()
to do the real job.
The memcpy_fromio macro maps _memcpy_fromio() in the current code.
But the _memcpy_fromio() will use readb() to do the copy work one byte
by one byte. This makes the read performance of NOR very slow(about 2~3MB/s).
A similiar discussion could be found in:
http://lists.infradead.org/pipermail/linux-arm-kernel/2009-November/003860.html
This patch replace the memcpy_fromio with memcpy which is optimized by the
kernel.
The following is the result from mtd_speedtest with M29W256GL7AN6E:
=================================================
mtd_speedtest: MTD device: 2
mtd_speedtest: not NAND flash, assume page size is 512 bytes.
mtd_speedtest: MTD device size 4194304, eraseblock size 131072, page size 512,
count of eraseblocks 32, pages per eraseblock 256, OOB size 0
mtd_speedtest: testing eraseblock write speed
mtd_speedtest: eraseblock write speed is 845 KiB/s
mtd_speedtest: testing eraseblock read speed
mtd_speedtest: eraseblock read speed is 19504 KiB/s
mtd_speedtest: testing page write speed
mtd_speedtest: page write speed is 845 KiB/s
mtd_speedtest: testing page read speed
mtd_speedtest: page read speed is 19140 KiB/s
mtd_speedtest: testing 2 page write speed
mtd_speedtest: 2 page write speed is 846 KiB/s
mtd_speedtest: testing 2 page read speed
mtd_speedtest: 2 page read speed is 19320 KiB/s
mtd_speedtest: Testing erase speed
mtd_speedtest: erase speed is 233 KiB/s
mtd_speedtest: Testing 2x multi-block erase speed
mtd_speedtest: 2x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 4x multi-block erase speed
mtd_speedtest: 4x multi-block erase speed is 224 KiB/s
mtd_speedtest: Testing 8x multi-block erase speed
mtd_speedtest: 8x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 16x multi-block erase speed
mtd_speedtest: 16x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 32x multi-block erase speed
mtd_speedtest: 32x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 64x multi-block erase speed
mtd_speedtest: 64x multi-block erase speed is 224 KiB/s
mtd_speedtest: finished
=================================================
Signed-off-by: Huang Shijie <b32955@freescale.com>
|
|
This reverts commit 573bab0be2427d6664420eaf9d8e272dbe9d840f.
i.mx6dl/dq sabreauto/sabresd board will boot up failed
randomly with this patch-set, thus revert it. [Jason]
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Huang Shijie <b32955@freescale.com>
|
|
imx_3.0.35_android
|
|
This reverts commit 573bab0be2427d6664420eaf9d8e272dbe9d840f.
i.mx6dl/dq sabreauto/sabresd board will boot up failed
randomly with this patch-set, thus revert it. [Jason]
Signed-off-by: Jason Liu <r64343@freescale.com>
|
|
All of the interrupts from the ENET block are not routed to
the GPC block. Hence ENET interrupts are not able to wake
up the SOC when the system is in WAIT mode. And the ENET
interrupt gets serviced only when another interrupt causes
the SOC to exit WAIT mode. This impacts the ENET performance.
To fix the issue two options:
1. Route the ENET interrupt to a GPIO. Need to enable the
CONFIG_MX6_ENET_IRQ_TO_GPIO in the config.
This patch provides support for routing the ENET interrupt
to GPIO_1_6. Routing to this GPIO requires no HW board mods.
If the GPIO_1_6 is being used for some other peripheral,
this patch can be followed to route the ENET interrupt to
any other GPIO though a HW mode maybe required.
2. If the GPIO mechanism cannot be used and is not enabled
by the above mentioned config, the patch will disable entry
to WAIT mode until ENET clock is active. When the ENET clock
is disabled, WAIT mode will be automatically enetered.
Signed-off-by: Ranjani Vaidyanathan <ra5478@freescale.com>
|
|
All of the interrupts from the ENET block are not routed to
the GPC block. Hence ENET interrupts are not able to wake
up the SOC when the system is in WAIT mode. And the ENET
interrupt gets serviced only when another interrupt causes
the SOC to exit WAIT mode. This impacts the ENET performance.
To fix the issue two options:
1. Route the ENET interrupt to a GPIO. Need to enable the
CONFIG_MX6_ENET_IRQ_TO_GPIO in the config.
This patch provides support for routing the ENET interrupt
to GPIO_1_6. Routing to this GPIO requires no HW board mods.
If the GPIO_1_6 is being used for some other peripheral,
this patch can be followed to route the ENET interrupt to
any other GPIO though a HW mode maybe required.
2. If the GPIO mechanism cannot be used and is not enabled
by the above mentioned config, the patch will disable entry
to WAIT mode until ENET clock is active. When the ENET clock
is disabled, WAIT mode will be automatically enetered.
Signed-off-by: Ranjani Vaidyanathan <ra5478@freescale.com>
|
|
imx_3.0.35_android
Conflicts:
drivers/net/fec.c
|
|
Conflicts:
drivers/video/mxc/ldb.c
|
|
There are so many retries happen on the per-cpu event device
when run the command 'cat /proc/timer_list', as following:
root@~$ cat /proc/timer_list
Timer List Version: v0.6
HRTIMER_MAX_CLOCK_BASES: 3
now at 3297691988044 nsecs
Tick Device: mode: 1
Per CPU device: 0
Clock Event Device: local_timer
max_delta_ns: 8624432320
min_delta_ns: 1000
mult: 2138893713
shift: 32
mode: 3
next_event: 3297700000000 nsecs
set_next_event: twd_set_next_event
set_mode: twd_set_mode
event_handler: hrtimer_interrupt
retries: 36383
the reason is that the local timer will stop when enter C3 state,
we need switch the local timer to bc timer when enter the state
and switch back when exit from the that state.The code is like this:
void arch_idle(void)
{
....
clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, &cpu);
enter_the_wait_mode();
clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_EXIT, &cpu);
}
when the broadcast timer interrupt arrives(this interrupt just wakeup
the ARM, and ARM has no chance to handle it since local irq is disabled.
In fact it's disabled in cpu_idle() of arch/arm/kernel/process.c)
the broadcast timer interrupt will wake up the CPU and run:
clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_EXIT, &cpu); ->
tick_broadcast_oneshot_control(...);
->
tick_program_event(dev->next_event, 1);
->
tick_dev_program_event(dev, expires, force);
->
for (i = 0;;) {
int ret = clockevents_program_event(dev, expires, now);
if (!ret || !force)
return ret;
dev->retries++;
....
now = ktime_get();
expires = ktime_add_ns(now, dev->min_delta_ns);
}
clockevents_program_event(dev, expires, now);
delta = ktime_to_ns(ktime_sub(expires, now));
if (delta <= 0)
return -ETIME;
when the bc timer interrupt arrives, which means the last local timer
expires too. so, clockevents_program_event will return -ETIME, which will
cause the dev->retries++ when retry to program the expired timer.
Even under the worst case, after the re-program the expired timer,
then CPU enter idle quickly before the re-progam timer expired,
it will make system ping-pang forever if no interrupt happen.
We have found the ping-pang issue during the video play-back test.
system will freeze and video not playing for sometime until other interrupt
occured to break the error condition.
The detailed information, please refer to the LKML:https://lkml.org/lkml/2013/2/20/216
which posted by Jason Liu.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jason Liu <r64343@freescale.com>
Tested-by: Jason Liu <r64343@freescale.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
There are so many retries happen on the per-cpu event device
when run the command 'cat /proc/timer_list', as following:
root@~$ cat /proc/timer_list
Timer List Version: v0.6
HRTIMER_MAX_CLOCK_BASES: 3
now at 3297691988044 nsecs
Tick Device: mode: 1
Per CPU device: 0
Clock Event Device: local_timer
max_delta_ns: 8624432320
min_delta_ns: 1000
mult: 2138893713
shift: 32
mode: 3
next_event: 3297700000000 nsecs
set_next_event: twd_set_next_event
set_mode: twd_set_mode
event_handler: hrtimer_interrupt
retries: 36383
the reason is that the local timer will stop when enter C3 state,
we need switch the local timer to bc timer when enter the state
and switch back when exit from the that state.The code is like this:
void arch_idle(void)
{
....
clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, &cpu);
enter_the_wait_mode();
clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_EXIT, &cpu);
}
when the broadcast timer interrupt arrives(this interrupt just wakeup
the ARM, and ARM has no chance to handle it since local irq is disabled.
In fact it's disabled in cpu_idle() of arch/arm/kernel/process.c)
the broadcast timer interrupt will wake up the CPU and run:
clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_EXIT, &cpu); ->
tick_broadcast_oneshot_control(...);
->
tick_program_event(dev->next_event, 1);
->
tick_dev_program_event(dev, expires, force);
->
for (i = 0;;) {
int ret = clockevents_program_event(dev, expires, now);
if (!ret || !force)
return ret;
dev->retries++;
....
now = ktime_get();
expires = ktime_add_ns(now, dev->min_delta_ns);
}
clockevents_program_event(dev, expires, now);
delta = ktime_to_ns(ktime_sub(expires, now));
if (delta <= 0)
return -ETIME;
when the bc timer interrupt arrives, which means the last local timer
expires too. so, clockevents_program_event will return -ETIME, which will
cause the dev->retries++ when retry to program the expired timer.
Even under the worst case, after the re-program the expired timer,
then CPU enter idle quickly before the re-progam timer expired,
it will make system ping-pang forever if no interrupt happen.
We have found the ping-pang issue during the video play-back test.
system will freeze and video not playing for sometime until other interrupt
occured to break the error condition.
The detailed information, please refer to the LKML:https://lkml.org/lkml/2013/2/20/216
which posted by Jason Liu.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jason Liu <r64343@freescale.com>
Tested-by: Jason Liu <r64343@freescale.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Conflicts:
arch/arm/mach-mx6/Makefile
arch/arm/mach-mx6/board-mx6dl_hdmidongle.h
arch/arm/mach-mx6/board-mx6q_hdmidongle.c
arch/arm/mach-mx6/board-mx6q_hdmidongle.h
arch/arm/mach-mx6/board-mx6q_sabreauto.c
arch/arm/mach-mx6/board-mx6q_sabrelite.c
drivers/media/video/mxc/capture/csi_v4l2_capture.c
drivers/media/video/mxc/capture/ipu_csi_enc.c
drivers/mxc/gpu-viv/arch/XAQ2/hal/kernel/gc_hal_kernel_hardware.c
drivers/mxc/gpu-viv/hal/kernel/gc_hal_kernel.c
drivers/mxc/gpu-viv/hal/kernel/gc_hal_kernel.h
drivers/mxc/gpu-viv/hal/kernel/inc/gc_hal.h
drivers/mxc/gpu-viv/hal/kernel/inc/gc_hal_compiler.h
drivers/mxc/gpu-viv/hal/kernel/inc/gc_hal_enum.h
drivers/mxc/gpu-viv/hal/kernel/inc/gc_hal_options.h
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_device.c
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_driver.c
drivers/mxc/vpu/mxc_vpu.c
drivers/usb/gadget/arcotg_udc.c
drivers/video/mxc/mxc_ipuv3_fb.c
drivers/video/mxc_hdmi.c
include/linux/mxcfb.h
sound/soc/imx/imx-wm8962.c
|
|
Add mxcfb ioctrl MXCFB_CSC_UPDATE to update IPU DP CSC matrix
for display adjustment.
This patch defines the ioctrl interface in header file.
Signed-off-by: Wayne Zou <b36644@freescale.com>
|
|
Make CARVEOUT ION heap be configured to be cachable as platform data
Signed-off-by: guoyin.chen <guoyin.chen@freescale.com>
|
|
Add deinterlace frame rate double flags for ipu header file
Signed-off-by: Wayne Zou <b36644@freescale.com>
|
|
The PHY register 0x9 and 0xe should setting
to different value in different board to pass HCT.
Add variable phy_reg_vlev and phy_reg_cksymtx to pass
phy config data.
Signed-off-by: Sandor Yu <R01008@freescale.com>
(cherry picked from commit 844aab72e7edcdced9f8e4e0d8e54eb4b0461cd9)
|
|
The PHY register 0x9 and 0xe should setting
to different value in different board to pass HCT.
Add variable phy_reg_vlev and phy_reg_cksymtx to pass
phy config data.
Signed-off-by: Sandor Yu <R01008@freescale.com>
|
|
Add check before relase ASRC pair to prevent ASRC register operation
while clock is not enabled. The ASRC clock is disable while index is not
applied.
Signed-off-by: Chen Liangjun <b36089@freescale.com>
|
|
imx_3.0.35_android
Conflicts:
arch/arm/mach-mx6/board-mx6q_sabrelite.c
arch/arm/mach-mx6/board-mx6q_sabresd.c
arch/arm/plat-mxc/cpufreq.c
|
|
This patch add device drvier for novatek touch screen driver.
This touch screen chip will be support because it have
more populary screen size.
Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
|
|
This patch add device drvier for novatek touch screen driver.
This touch screen chip will be support because it have
more populary screen size.
Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
|
