| Age | Commit message (Collapse) | Author |
|---|
|
Show the last issued command in warning messages when any communication
error with CORB/RIRB occurs.
Also, a bit code clean-up for composing the command value in
*_send_cmd().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fixed the invalid use of schedule_timeout_interruptible() without
checking pending signals. Simply replaced with schedule_timeout().
Suggestions thanks to Jeff Garzik.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Add the MCP73/MCP77 support to hda driver.
The patch base on kernel 2.6.22-rc4
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This patch is for ATI RS780 and R600 HDMI support.
Signed-off-by: Wolke Liu <wolke.liu@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Some boards have the audio codec on slot #3 while the modem codec
on slot #0. The driver should continue to probe the slots when
no audio codec is found.
This fixes the problem of no device on Toshiba A100 (and some other
ATI SB450 devices).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Probing the codec slots on ATI controller causes problems on some
devices like Acer laptops. On these devices, reading from codec
slot 3 results in the communication failure with the codec chip.
Meanwhile, some laptops (e.g. Gateway) have the codec connection
only on slot 3, and probing this slot is mandatory for them.
The patch improves the probing robustness. The additional slots
are now checked only when no codecs are found in the primary three
slots.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
CC [M] sound/pci/hda/hda_intel.o
sound/pci/hda/hda_intel.c:1508: error: position_fix_list causes a section type conflict
Gcc like its __devinitdata readable not const, it seems. An alternative
fix would be to remove the __devinitdata attribute but that would result
in slight runtime bloat.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
From the HDA spec it appears that the buffers written to the BDL and
sent to a codec must be 128 byte aligned (section 4.5.1). The alignment
was not happening especially when playing 6 channels. This patch set
the alignment of buffers and periods to 128 bytes.
Signed-off-by: Joachim Deguara <joachim.deguara@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
ATI controllers may have up to 4 codecs while ICH up to 3.
Thus the earlier fix to change AZX_MAX_CODECS to 3 cause a regression
on some devices that have the audio codec at bit#3.
Now max codecs is defined according to the driver type, either 3 or 4.
Currently 4 is set only to ATI chips. Other might need the same
change, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Some devices are known to require position_fix=1 or 2 to make the
driver working correctly. Otherwise the sound gets weird effects,
such as stutters.
Now a black/whitelist is introduced to indicate the position_fix
value explicitly for such misbehaving hardwares. As a first example,
Dell D820 is listed there. More will come later likely...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fix the max number of codecs detected by HD-intel (and compatible)
controllers to 3. Some hardware reports extra bits as if
connected, and the driver gets confused to probe unexisting codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Call pci_intx() to disable/enable INTX when MSI is used/unused.
Nvidia and AMD boards seem to have problems with MSI when INTX
isn't disabled.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
See ALSA bug#2481 .
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This patch adds the Intel ICH9 HD Audio controller DID's for ALSA.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Add the support for HD audio controllers of MCP51,MCP55,MCP61,MCP65 & MCP67.
Signed-off-by: Peer Chen <pchen@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fix IRQ flags for PCI devices.
The shared IRQs for PCI devices shouldn't be allocated with
IRQF_DISABLED. Also, when MSI is enabled, IRQF_SHARED shouldn't
be used.
The patch removes unnecessary cast in request_irq and free_irq,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Disable MSI support on HD-audio driver as default since there are too
many broken devices.
The module option is changed from disable_msi to enable_msi, too. For
turning MSI support on, pass enable_msi=1, instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Check the availability of MSI and turn off MSI automatically when it's
not available on the hardware. MSI seems broken on some hardwares
but the kernel doesn't know exactly, thus we have to turn the MSI
feature off on the sound driver manually.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This patch adds support for the HDMI codec of the ATI RS690 IGP northbridge.
Signed-off-by: Felix Kuehling <fkuehlin@ati.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
- Check the return value of pci_enable_device() and request_irq()
in the suspend. If any error occurs there, disable the device
using snd_card_disconnect().
- Call pci_set_power_state() properly with pci_choose_state().
- Fix the order to call pci_set_power_state().
- Removed obsolete house-made PM codes in some drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Added the new PCI id to support Nvidia MCP61 in snd-hda-intel driver.
Signed-off-by: Dan Cyr <rabidfly@hotmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
|
|
A slight cleanup of timeout check in azx_get_response() to check
jiffies for HZ-independent timeout.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fixed suspend/resume with MSI enablement.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Assign the SPDIF always to the secondary device (dev#1) to keep
the same configuration. Move the optional capture device to the
third device (dev#2).
hda_intel now just ignores the NULL entries in the pcm arrays
from codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fix the order to call pci_disable_msi() to be after free_irq().
(Otherwise pci_disable_msi() bugs you.)
Also, added a description of disable_msi option to documentation.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Cleanup whitespace.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Removed volatile from the position buffer pointer.
Also, use synchronize_irq() instead of unreliable msleep(1)
in the driver remove callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Simple patch to enable Message Signalled Interrupts for the HDA Intel
audio controller. Tested with:
Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03)
MSI is better because it means audio doesn't end up sharing IRQ with USB.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Automatically switch to polling mode for CORB/RIRB communication
if the irq-driven mode seems not working well. If the polling
mode still doesn't work, switch to single_cmd mode as fallback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fixed 'section mismatch' errors in ALSA PCI drivers:
- removed invalid __devinitdata from pci id tables
- fix/remove __devinit of functions called in suspend/resume
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Call iounmap after free_irq to avoid invalid accesses in the
shared irq. The patch is taken from
https://bugzilla.novell.com/show_bug.cgi?id=167869
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add support for the ATI RS600 HDMI audio device. It has a one-stream
pure digital stereo codec that isn't handled by the generic codec
support.
Signed-off-by: Felix Kuehling <fkuehlin@ati.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds support for high definition audio on ATI SB600.
Signed-off-by: Felix Kuehling <fkuehlin@ati.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Intel driver
Switch the method to measure the current DMA position automatically
from position-buffer mode to LPIB-read mode with a sanity check.
Some hardwares seems to have problem with the position buffer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Codec driver,HDA Intel driver
Switch to single_cmd mode automatically as a fallback when CORB/RIRB
communication doesn't work well. It may make the driver working on
some devices with broken BIOS/ACPI support.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: Documentation,HDA Intel driver
Added single_cmd module option for debugging in the case CORB/RIRB
doesn't work well (e.g. due to wrong irq routings).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Intel driver
This patch adds the Intel ICH8 HD Audio DID to the hda_intel.c audio driver.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Intel driver
The probe_mask module parameter comment notes that the intended
default is -1. Fix it to be so, otherwise all codecs are skipped
and init fails.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Intel driver
- Use the position buffer for obtaining the current DMA position
as default. This seems more stable than others.
- Add probe_mask module option (mainly for test boards with multiple
codecs).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Intel driver
Fix PM support on HDA-Intel driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Intel driver
Remove xxx_t typedefs from the HDA-Intel driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: HDA Intel driver
Rate-limit the azx_get_response timeout message. A continuous 2 per second
is too much.
Signed-off-by: Randy Dunlap <randy_d_dunlap@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix the type of enable module option to bool.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added dummay obsoleted module options for backward compatibility
(to reduce possible bugzilla entries :)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove the code for supporting eight cards from the integrated
controller drivers because There Can Be Only One controller of
each type per mainboard.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
