From a74fe1194b8da1dcee7529ba14999381bb9c25d9 Mon Sep 17 00:00:00 2001 From: Sven Neumann Date: Wed, 25 May 2011 13:37:32 +0200 Subject: ARM: pxa/raumfeld: display initialisation fixes The display requires some milliseconds between GPIO_TFT_VA_EN and GPIO_DISPLAY_ENABLE. Reorder initialisation to comply with the display spec. Also tune timings for better compliance with the spec. Signed-off-by: Sven Neumann Acked-by: Daniel Mack Signed-off-by: Eric Miao --- arch/arm/mach-pxa/raumfeld.c | 29 +++++++++++++++-------------- 1 file changed, 15 insertions(+), 14 deletions(-) (limited to 'arch/arm/mach-pxa') diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c index 8e5b3d8a86be..9caa5e5c8d94 100644 --- a/arch/arm/mach-pxa/raumfeld.c +++ b/arch/arm/mach-pxa/raumfeld.c @@ -573,10 +573,10 @@ static struct pxafb_mode_info sharp_lq043t3dx02_mode = { .xres = 480, .yres = 272, .bpp = 16, - .hsync_len = 4, + .hsync_len = 41, .left_margin = 2, .right_margin = 1, - .vsync_len = 1, + .vsync_len = 10, .upper_margin = 3, .lower_margin = 1, .sync = 0, @@ -596,30 +596,31 @@ static void __init raumfeld_lcd_init(void) { int ret; - pxa_set_fb_info(NULL, &raumfeld_sharp_lcd_info); - - /* Hardware revision 2 has the backlight regulator controlled - * by an LT3593, earlier and later devices use PWM for that. */ - if ((system_rev & 0xff) == 2) { - platform_device_register(&raumfeld_lt3593_device); - } else { - mfp_cfg_t raumfeld_pwm_pin_config = GPIO17_PWM0_OUT; - pxa3xx_mfp_config(&raumfeld_pwm_pin_config, 1); - platform_device_register(&raumfeld_pwm_backlight_device); - } - ret = gpio_request(GPIO_TFT_VA_EN, "display VA enable"); if (ret < 0) pr_warning("Unable to request GPIO_TFT_VA_EN\n"); else gpio_direction_output(GPIO_TFT_VA_EN, 1); + msleep(100); + ret = gpio_request(GPIO_DISPLAY_ENABLE, "display enable"); if (ret < 0) pr_warning("Unable to request GPIO_DISPLAY_ENABLE\n"); else gpio_direction_output(GPIO_DISPLAY_ENABLE, 1); + /* Hardware revision 2 has the backlight regulator controlled + * by an LT3593, earlier and later devices use PWM for that. */ + if ((system_rev & 0xff) == 2) { + platform_device_register(&raumfeld_lt3593_device); + } else { + mfp_cfg_t raumfeld_pwm_pin_config = GPIO17_PWM0_OUT; + pxa3xx_mfp_config(&raumfeld_pwm_pin_config, 1); + platform_device_register(&raumfeld_pwm_backlight_device); + } + + pxa_set_fb_info(NULL, &raumfeld_sharp_lcd_info); platform_device_register(&pxa3xx_device_gcu); } -- cgit v1.2.3