From fa01e2ca9f531b4a5693469a196eb1574b8d7d8a Mon Sep 17 00:00:00 2001 From: Ricardo Ribalda Delgado Date: Wed, 27 Apr 2016 10:40:10 +0200 Subject: serial: 8250: Integrate Fintek into 8250_base The 8250_fintek driver advertises as the PNP0501 driver; however this conflicts with the standard 16550A uart PNP0501. The conflict causes the 8250_fintek driver to load with _every_ PNP0501, but never probe, and causing the entire 8250 driver stack to unload if the 8250_fintek driver is unloaded (modprobe doesn't know that 8250_pnp rather than 8250_fintek claimed the resource). This patch merges the Fintek driver into 8250_base. On autoconfig_16550 the device is probed to verify if it is a FINTEK device or not. This custom probing can be disabled completely via configuration. When a Fintek device is not probed it will behave as a standard 16550A device, with no RS485 capabilities. Reported-by: Peter Hurley Signed-off-by: Ricardo Ribalda Delgado Reviewed-by: Peter Hurley Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/8250/8250.h | 6 ++ drivers/tty/serial/8250/8250_fintek.c | 118 +++++----------------------------- drivers/tty/serial/8250/8250_port.c | 7 ++ drivers/tty/serial/8250/Kconfig | 20 +++--- drivers/tty/serial/8250/Makefile | 2 +- 5 files changed, 42 insertions(+), 111 deletions(-) (limited to 'drivers/tty/serial/8250') diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h index 7a4c82633964..215a99237e95 100644 --- a/drivers/tty/serial/8250/8250.h +++ b/drivers/tty/serial/8250/8250.h @@ -150,6 +150,12 @@ static inline int serial8250_pnp_init(void) { return 0; } static inline void serial8250_pnp_exit(void) { } #endif +#ifdef CONFIG_SERIAL_8250_FINTEK +int fintek_8250_probe(struct uart_8250_port *uart); +#else +static inline int fintek_8250_probe(struct uart_8250_port *uart) { return 0; } +#endif + #ifdef CONFIG_ARCH_OMAP1 static inline int is_omap1_8250(struct uart_8250_port *pt) { diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c index 89474399ab89..870981dd9e39 100644 --- a/drivers/tty/serial/8250/8250_fintek.c +++ b/drivers/tty/serial/8250/8250_fintek.c @@ -1,9 +1,7 @@ /* * Probe for F81216A LPC to 4 UART * - * Based on drivers/tty/serial/8250_pnp.c, by Russell King, et al - * - * Copyright (C) 2014 Ricardo Ribalda, Qtechnology A/S + * Copyright (C) 2014-2016 Ricardo Ribalda, Qtechnology A/S * * * This program is free software; you can redistribute it and/or modify @@ -38,19 +36,15 @@ #define RXW4C_IRA BIT(3) #define TXW4C_IRA BIT(2) -#define DRIVER_NAME "8250_fintek" - struct fintek_8250 { u16 base_port; u8 index; u8 key; - long line; }; static int fintek_8250_enter_key(u16 base_port, u8 key) { - - if (!request_muxed_region(base_port, 2, DRIVER_NAME)) + if (!request_muxed_region(base_port, 2, "8250_fintek")) return -EBUSY; outb(key, base_port + ADDR_PORT); @@ -138,7 +132,7 @@ static int fintek_8250_rs485_config(struct uart_port *port, return 0; } -static int fintek_8250_base_port(u16 io_address, u8 *key, u8 *index) +static int find_base_port(struct fintek_8250 *pdata, u16 io_address) { static const u16 addr[] = {0x4e, 0x2e}; static const u8 keys[] = {0x77, 0xa0, 0x87, 0x67}; @@ -168,10 +162,13 @@ static int fintek_8250_base_port(u16 io_address, u8 *key, u8 *index) continue; fintek_8250_exit_key(addr[i]); - *key = keys[j]; - *index = k; - return addr[i]; + pdata->key = keys[j]; + pdata->base_port = addr[i]; + pdata->index = k; + + return 0; } + fintek_8250_exit_key(addr[i]); } } @@ -179,104 +176,21 @@ static int fintek_8250_base_port(u16 io_address, u8 *key, u8 *index) return -ENODEV; } -static int -fintek_8250_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id) +int fintek_8250_probe(struct uart_8250_port *uart) { - struct uart_8250_port uart; struct fintek_8250 *pdata; - int base_port; - u8 key; - u8 index; - - if (!pnp_port_valid(dev, 0)) - return -ENODEV; + struct fintek_8250 probe_data; - base_port = fintek_8250_base_port(pnp_port_start(dev, 0), &key, &index); - if (base_port < 0) + if (find_base_port(&probe_data, uart->port.iobase)) return -ENODEV; - memset(&uart, 0, sizeof(uart)); - - pdata = devm_kzalloc(&dev->dev, sizeof(*pdata), GFP_KERNEL); + pdata = devm_kzalloc(uart->port.dev, sizeof(*pdata), GFP_KERNEL); if (!pdata) return -ENOMEM; - uart.port.private_data = pdata; - if (!pnp_irq_valid(dev, 0)) - return -ENODEV; - uart.port.irq = pnp_irq(dev, 0); - uart.port.iobase = pnp_port_start(dev, 0); - uart.port.iotype = UPIO_PORT; - uart.port.rs485_config = fintek_8250_rs485_config; - - uart.port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF; - if (pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE) - uart.port.flags |= UPF_SHARE_IRQ; - uart.port.uartclk = 1843200; - uart.port.dev = &dev->dev; - - pdata->key = key; - pdata->base_port = base_port; - pdata->index = index; - pdata->line = serial8250_register_8250_port(&uart); - if (pdata->line < 0) - return -ENODEV; + memcpy(pdata, &probe_data, sizeof(probe_data)); + uart->port.rs485_config = fintek_8250_rs485_config; + uart->port.private_data = pdata; - pnp_set_drvdata(dev, pdata); return 0; } - -static void fintek_8250_remove(struct pnp_dev *dev) -{ - struct fintek_8250 *pdata = pnp_get_drvdata(dev); - - if (pdata) - serial8250_unregister_port(pdata->line); -} - -#ifdef CONFIG_PM -static int fintek_8250_suspend(struct pnp_dev *dev, pm_message_t state) -{ - struct fintek_8250 *pdata = pnp_get_drvdata(dev); - - if (!pdata) - return -ENODEV; - serial8250_suspend_port(pdata->line); - return 0; -} - -static int fintek_8250_resume(struct pnp_dev *dev) -{ - struct fintek_8250 *pdata = pnp_get_drvdata(dev); - - if (!pdata) - return -ENODEV; - serial8250_resume_port(pdata->line); - return 0; -} -#else -#define fintek_8250_suspend NULL -#define fintek_8250_resume NULL -#endif /* CONFIG_PM */ - -static const struct pnp_device_id fintek_dev_table[] = { - /* Qtechnology Panel PC / IO1000 */ - { "PNP0501"}, - {} -}; - -MODULE_DEVICE_TABLE(pnp, fintek_dev_table); - -static struct pnp_driver fintek_8250_driver = { - .name = DRIVER_NAME, - .probe = fintek_8250_probe, - .remove = fintek_8250_remove, - .suspend = fintek_8250_suspend, - .resume = fintek_8250_resume, - .id_table = fintek_dev_table, -}; - -module_pnp_driver(fintek_8250_driver); -MODULE_DESCRIPTION("Fintek F812164 module"); -MODULE_AUTHOR("Ricardo Ribalda "); -MODULE_LICENSE("GPL"); diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c index 215e8da78a06..d4036038a4dd 100644 --- a/drivers/tty/serial/8250/8250_port.c +++ b/drivers/tty/serial/8250/8250_port.c @@ -1315,6 +1315,13 @@ static void autoconfig(struct uart_8250_port *up) out_lock: spin_unlock_irqrestore(&port->lock, flags); + + /* + * Check if the device is a Fintek F81216A + */ + if (port->type == PORT_16550A) + fintek_8250_probe(up); + if (up->capabilities != old_capabilities) { pr_warn("ttyS%d: detected caps %08x should be %08x\n", serial_index(port), old_capabilities, diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig index 7f33d3494cea..e46761d20f7b 100644 --- a/drivers/tty/serial/8250/Kconfig +++ b/drivers/tty/serial/8250/Kconfig @@ -57,6 +57,18 @@ config SERIAL_8250_PNP This builds standard PNP serial support. You may be able to disable this feature if you only need legacy serial support. +config SERIAL_8250_FINTEK + bool "Support for Fintek F81216A LPC to 4 UART RS485 API" + depends on SERIAL_8250 + ---help--- + Selecting this option will add support for the RS485 capabilities + of the Fintek F81216A LPC to 4 UART. + + If this option is not selected the device will be configured as a + standard 16550A serial port. + + If unsure, say N. + config SERIAL_8250_CONSOLE bool "Console on 8250/16550 and compatible serial port" depends on SERIAL_8250=y @@ -358,14 +370,6 @@ config SERIAL_8250_OMAP_TTYO_FIXUP not booting kernel because the serial console remains silent in case they forgot to update the command line. -config SERIAL_8250_FINTEK - tristate "Support for Fintek F81216A LPC to 4 UART" - depends on SERIAL_8250 && PNP - help - Selecting this option will add support for the Fintek F81216A - LPC to 4 UART. This device has some RS485 functionality not available - through the PNP driver. If unsure, say N. - config SERIAL_8250_LPC18XX tristate "NXP LPC18xx/43xx serial port support" depends on SERIAL_8250 && OF && (ARCH_LPC18XX || COMPILE_TEST) diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile index c9a2d6ed87e9..367d403d28d5 100644 --- a/drivers/tty/serial/8250/Makefile +++ b/drivers/tty/serial/8250/Makefile @@ -7,6 +7,7 @@ obj-$(CONFIG_SERIAL_8250) += 8250.o 8250_base.o 8250-$(CONFIG_SERIAL_8250_PNP) += 8250_pnp.o 8250_base-y := 8250_port.o 8250_base-$(CONFIG_SERIAL_8250_DMA) += 8250_dma.o +8250_base-$(CONFIG_SERIAL_8250_FINTEK) += 8250_fintek.o obj-$(CONFIG_SERIAL_8250_GSC) += 8250_gsc.o obj-$(CONFIG_SERIAL_8250_PCI) += 8250_pci.o obj-$(CONFIG_SERIAL_8250_HP300) += 8250_hp300.o @@ -23,7 +24,6 @@ obj-$(CONFIG_SERIAL_8250_FSL) += 8250_fsl.o obj-$(CONFIG_SERIAL_8250_DW) += 8250_dw.o obj-$(CONFIG_SERIAL_8250_EM) += 8250_em.o obj-$(CONFIG_SERIAL_8250_OMAP) += 8250_omap.o -obj-$(CONFIG_SERIAL_8250_FINTEK) += 8250_fintek.o obj-$(CONFIG_SERIAL_8250_LPC18XX) += 8250_lpc18xx.o obj-$(CONFIG_SERIAL_8250_MT6577) += 8250_mtk.o obj-$(CONFIG_SERIAL_8250_UNIPHIER) += 8250_uniphier.o -- cgit v1.2.3