/* SPDX-License-Identifier: GPL-2.0+ */ /* * plx9080.h * * Copyright (C) 2002,2003 Frank Mori Hess * ******************************************************************** * * Copyright (C) 1999 RG Studio s.c. * Written by Krzysztof Halasa * * Portions (C) SBE Inc., used by permission. */ #ifndef __COMEDI_PLX9080_H #define __COMEDI_PLX9080_H #include #include #include #include #include #include /** * struct plx_dma_desc - DMA descriptor format for PLX PCI 9080 * @pci_start_addr: PCI Bus address for transfer (DMAPADR). * @local_start_addr: Local Bus address for transfer (DMALADR). * @transfer_size: Transfer size in bytes (max 8 MiB) (DMASIZ). * @next: Address of next descriptor + flags (DMADPR). * * Describes the format of a scatter-gather DMA descriptor for the PLX * PCI 9080. All members are raw, little-endian register values that * will be transferred by the DMA engine from local or PCI memory into * corresponding registers for the DMA channel. * * The DMA descriptors must be aligned on a 16-byte boundary. Bits 3:0 * of @next contain flags describing the address space of the next * descriptor (local or PCI), an "end of chain" marker, an "interrupt on * terminal count" bit, and a data transfer direction. */ struct plx_dma_desc { __le32 pci_start_addr; __le32 local_start_addr; __le32 transfer_size; __le32 next; }; /* * Register Offsets and Bit Definitions */ /* Local Address Space 0 Range Register */ #define PLX_REG_LAS0RR 0x0000 /* Local Address Space 1 Range Register */ #define PLX_REG_LAS1RR 0x00f0 #define PLX_LASRR_IO BIT(0) /* Map to: 1=I/O, 0=Mem */ #define PLX_LASRR_MLOC_ANY32 (BIT(1) * 0) /* Locate anywhere in 32 bit */ #define PLX_LASRR_MLOC_LT1MB (BIT(1) * 1) /* Locate in 1st meg */ #define PLX_LASRR_MLOC_ANY64 (BIT(1) * 2) /* Locate anywhere in 64 bit */ #define PLX_LASRR_MLOC_MASK GENMASK(2, 1) /* Memory location bits */ #define PLX_LASRR_PREFETCH BIT(3) /* Memory is prefetchable */ /* bits that specify range for memory space decode bits */ #define PLX_LASRR_MEM_MASK GENMASK(31, 4) /* bits that specify range for i/o space decode bits */ #define PLX_LASRR_IO_MASK GENMASK(31, 2) /* Local Address Space 0 Local Base Address (Remap) Register */ #define PLX_REG_LAS0BA 0x0004 /* Local Address Space 1 Local Base Address (Remap) Register */ #define PLX_REG_LAS1BA 0x00f4 #define PLX_LASBA_EN BIT(0) /* Enable slave decode */ /* bits that specify local base address for memory space */ #define PLX_LASBA_MEM_MASK GENMASK(31, 4) /* bits that specify local base address for i/o space */ #define PLX_LASBA_IO_MASK GENMASK(31, 2) /* Mode/Arbitration Register */ #define PLX_REG_MARBR 0x0008 /* DMA Arbitration Register (alias of MARBR). */ #define PLX_REG_DMAARB 0x00ac /* Local Bus Latency Timer */ #define PLX_MARBR_LT(x) (BIT(0) * ((x) & 0xff)) #define PLX_MARBR_LT_MASK GENMASK(7, 0) #define PLX_MARBR_TO_LT(r) ((r) & PLX_MARBR_LT_MASK) /* Local Bus Pause Timer */ #define PLX_MARBR_PT(x) (BIT(8) * ((x) & 0xff)) #define PLX_MARBR_PT_MASK GENMASK(15, 8) #define PLX_MARBR_TO_PT(r) (((r) & PLX_MARBR_PT_MASK) >> 8) /* Local Bus Latency Timer Enable */ #define PLX_MARBR_LTEN BIT(16) /* Local Bus Pause Timer Enable */ #define PLX_MARBR_PTEN BIT(17) /* Local Bus BREQ Enable */ #define PLX_MARBR_BREQEN BIT(18) /* DMA Channel Priority */ #define PLX_MARBR_PRIO_ROT (BIT(19) * 0) /* Rotational priority */ #define PLX_MARBR_PRIO_DMA0 (BIT(19) * 1) /* DMA channel 0 has priority */ #define PLX_MARBR_PRIO_DMA1 (BIT(19) * 2) /* DMA channel 1 has priority */ #define PLX_MARBR_PRIO_MASK GENMASK(20, 19) /* Local Bus Direct Slave Give Up Bus Mode */ #define PLX_MARBR_DSGUBM BIT(21) /* Direct Slace LLOCKo# Enable */ #define PLX_MARBR_DSLLOCKOEN BIT(22) /* PCI Request Mode */ #define PLX_MARBR_PCIREQM BIT(23) /* PCI Specification v2.1 Mode */ #define PLX_MARBR_PCIV21M BIT(24) /* PCI Read No Write Mode */ #define PLX_MARBR_PCIRNWM BIT(25) /* PCI Read with Write Flush Mode */ #define PLX_MARBR_PCIRWFM BIT(26) /* Gate Local Bus Latency Timer with BREQ */ #define PLX_MARBR_GLTBREQ BIT(27) /* PCI Read No Flush Mode */ #define PLX_MARBR_PCIRNFM BIT(28) /* * Make reads from PCI Configuration register 0 return Subsystem ID and * Subsystem Vendor ID instead of Device ID and Vendor ID */ #define PLX_MARBR_SUBSYSIDS BIT(29) /* Big/Little Endian Descriptor Register */ #define PLX_REG_BIGEND 0x000c /* Configuration Register Big Endian Mode */ #define PLX_BIGEND_CONFIG BIT(0) /* Direct Master Big Endian Mode */ #define PLX_BIGEND_DM BIT(1) /* Direct Slave Address Space 0 Big Endian Mode */ #define PLX_BIGEND_DSAS0 BIT(2) /* Direct Slave Expansion ROM Big Endian Mode */ #define PLX_BIGEND_EROM BIT(3) /* Big Endian Byte Lane Mode - use most significant byte lanes */ #define PLX_BIGEND_BEBLM BIT(4) /* Direct Slave Address Space 1 Big Endian Mode */ #define PLX_BIGEND_DSAS1 BIT(5) /* DMA Channel 1 Big Endian Mode */ #define PLX_BIGEND_DMA1 BIT(6) /* DMA Channel 0 Big Endian Mode */ #define PLX_BIGEND_DMA0 BIT(7) /* DMA Channel N Big Endian Mode (N <= 1) */ #define PLX_BIGEND_DMA(n) ((n) ? PLX_BIGEND_DMA1 : PLX_BIGEND_DMA0) /* * Note: The Expansion ROM stuff is only relevant to the PC environment. * This expansion ROM code is executed by the host CPU at boot time. * For this reason no bit definitions are provided here. */ /* Expansion ROM Range Register */ #define PLX_REG_EROMRR 0x0010 /* Expansion ROM Local Base Address (Remap) Register */ #define PLX_REG_EROMBA 0x0014 /* Local Address Space 0/Expansion ROM Bus Region Descriptor Register */ #define PLX_REG_LBRD0 0x0018 /* Local Address Space 1 Bus Region Descriptor Register */ #define PLX_REG_LBRD1 0x00f8 /* Memory Space Local Bus Width */ #define PLX_LBRD_MSWIDTH_8 (BIT(0) * 0) /* 8 bits wide */ #define PLX_LBRD_MSWIDTH_16 (BIT(0) * 1) /* 16 bits wide */ #define PLX_LBRD_MSWIDTH_32 (BIT(0) * 2) /* 32 bits wide */ #define PLX_LBRD_MSWIDTH_32A (BIT(0) * 3) /* 32 bits wide */ #define PLX_LBRD_MSWIDTH_MASK GENMASK(1, 0) /* Memory Space Internal Wait States */ #define PLX_LBRD_MSIWS(x) (BIT(2) * ((x) & 0xf)) #define PLX_LBRD_MSIWS_MASK GENMASK(5, 2) #define PLX_LBRD_TO_MSIWS(r) (((r) & PLS_LBRD_MSIWS_MASK) >> 2) /* Memory Space Ready Input Enable */ #define PLX_LBRD_MSREADYIEN BIT(6) /* Memory Space BTERM# Input Enable */ #define PLX_LBRD_MSBTERMIEN BIT(7) /* Memory Space 0 Prefetch Disable (LBRD0 only) */ #define PLX_LBRD0_MSPREDIS BIT(8) /* Memory Space 1 Burst Enable (LBRD1 only) */ #define PLX_LBRD1_MSBURSTEN BIT(8) /* Expansion ROM Space Prefetch Disable (LBRD0 only) */ #define PLX_LBRD0_EROMPREDIS BIT(9) /* Memory Space 1 Prefetch Disable (LBRD1 only) */ #define PLX_LBRD1_MSPREDIS BIT(9) /* Read Prefetch Count Enable */ #define PLX_LBRD_RPFCOUNTEN BIT(10) /* Prefetch Counter */ #define PLX_LBRD_PFCOUNT(x) (BIT(11) * ((x) & 0xf)) #define PLX_LBRD_PFCOUNT_MASK GENMASK(14, 11) #define PLX_LBRD_TO_PFCOUNT(r) (((r) & PLX_LBRD_PFCOUNT_MASK) >> 11) /* Expansion ROM Space Local Bus Width (LBRD0 only) */ #define PLX_LBRD0_EROMWIDTH_8 (BIT(16) * 0) /* 8 bits wide */ #define PLX_LBRD0_EROMWIDTH_16 (BIT(16) * 1) /* 16 bits wide */ #define PLX_LBRD0_EROMWIDTH_32 (BIT(16) * 2) /* 32 bits wide */ #define PLX_LBRD0_EROMWIDTH_32A (BIT(16) * 3) /* 32 bits wide */ #define PLX_LBRD0_EROMWIDTH_MASK GENMASK(17, 16) /* Expansion ROM Space Internal Wait States (LBRD0 only) */ #define PLX_LBRD0_EROMIWS(x) (BIT(18) * ((x) & 0xf)) #define PLX_LBRD0_EROMIWS_MASK GENMASK(21, 18) #define PLX_LBRD0_TO_EROMIWS(r) (((r) & PLX_LBRD0_EROMIWS_MASK) >> 18) /* Expansion ROM Space Ready Input Enable (LBDR0 only) */ #define PLX_LBRD0_EROMREADYIEN BIT(22) /* Expansion ROM Space BTERM# Input Enable (LBRD0 only) */ #define PLX_LBRD0_EROMBTERMIEN BIT(23) /* Memory Space 0 Burst Enable (LBRD0 only) */ #define PLX_LBRD0_MSBURSTEN BIT(24) /* Extra Long Load From Serial EEPROM (LBRD0 only) */ #define PLX_LBRD0_EELONGLOAD BIT(25) /* Expansion ROM Space Burst Enable (LBRD0 only) */ #define PLX_LBRD0_EROMBURSTEN BIT(26) /* Direct Slave PCI Write Mode - assert TRDY# when FIFO full (LBRD0 only) */ #define PLX_LBRD0_DSWMTRDY BIT(27) /* PCI Target Retry Delay Clocks / 8 (LBRD0 only) */ #define PLX_LBRD0_TRDELAY(x) (BIT(28) * ((x) & 0xF)) #define PLX_LBRD0_TRDELAY_MASK GENMASK(31, 28) #define PLX_LBRD0_TO_TRDELAY(r) (((r) & PLX_LBRD0_TRDELAY_MASK) >> 28) /* Local Range Register for Direct Master to PCI */ #define PLX_REG_DMRR 0x001c /* Local Bus Base Address Register for Direct Master to PCI Memory */ #define PLX_REG_DMLBAM 0x0020 /* Local Base Address Register for Direct Master to PCI IO/CFG */ #define PLX_REG_DMLBAI 0x0024 /* PCI Base Address (Remap) Register for Direct Master to PCI Memory */ #define PLX_REG_DMPBAM 0x0028 /* Direct Master Memory Access Enable */ #define PLX_DMPBAM_MEMACCEN BIT(0) /* Direct Master I/O Access Enable */ #define PLX_DMPBAM_IOACCEN BIT(1) /* LLOCK# Input Enable */ #define PLX_DMPBAM_LLOCKIEN BIT(2) /* Direct Master Read Prefetch Size Control (bits 12, 3) */ #define PLX_DMPBAM_RPSIZE_CONT ((BIT(12) * 0) | (BIT(3) * 0)) #define PLX_DMPBAM_RPSIZE_4 ((BIT(12) * 0) | (BIT(3) * 1)) #define PLX_DMPBAM_RPSIZE_8 ((BIT(12) * 1) | (BIT(3) * 0)) #define PLX_DMPBAM_RPSIZE_16 ((BIT(12) * 1) | (BIT(3) * 1)) #define PLX_DMPBAM_RPSIZE_MASK (BIT(12) | BIT(3)) /* Direct Master PCI Read Mode - deassert IRDY when FIFO full */ #define PLX_DMPBAM_RMIRDY BIT(4) /* Programmable Almost Full Level (bits 10, 8:5) */ #define PLX_DMPBAM_PAFL(x) ((BIT(10) * !!((x) & 0x10)) | \ (BIT(5) * ((x) & 0xf))) #define PLX_DMPBAM_TO_PAFL(v) ((((BIT(10) & (v)) >> 1) | \ (GENMASK(8, 5) & (v))) >> 5) #define PLX_DMPBAM_PAFL_MASK (BIT(10) | GENMASK(8, 5)) /* Write And Invalidate Mode */ #define PLX_DMPBAM_WIM BIT(9) /* Direct Master Prefetch Limit */ #define PLX_DBPBAM_PFLIMIT BIT(11) /* I/O Remap Select */ #define PLX_DMPBAM_IOREMAPSEL BIT(13) /* Direct Master Write Delay */ #define PLX_DMPBAM_WDELAY_NONE (BIT(14) * 0) #define PLX_DMPBAM_WDELAY_4 (BIT(14) * 1) #define PLX_DMPBAM_WDELAY_8 (BIT(14) * 2) #define PLX_DMPBAM_WDELAY_16 (BIT(14) * 3) #define PLX_DMPBAM_WDELAY_MASK GENMASK(15, 14) /* Remap of Local-to-PCI Space Into PCI Address Space */ #define PLX_DMPBAM_REMAP_MASK GENMASK(31, 16) /* PCI Configuration Address Register for Direct Master to PCI IO/CFG */ #define PLX_REG_DMCFGA 0x002c /* Congiguration Type */ #define PLX_DMCFGA_TYPE0 (BIT(0) * 0) #define PLX_DMCFGA_TYPE1 (BIT(0) * 1) #define PLX_DMCFGA_TYPE_MASK GENMASK(1, 0) /* Register Number */ #define PLX_DMCFGA_REGNUM(x) (BIT(2) * ((x) & 0x3f)) #define PLX_DMCFGA_REGNUM_MASK GENMASK(7, 2) #define PLX_DMCFGA_TO_REGNUM(r) (((r) & PLX_DMCFGA_REGNUM_MASK) >> 2) /* Function Number */ #define PLX_DMCFGA_FUNCNUM(x) (BIT(8) * ((x) & 0x7)) #define PLX_DMCFGA_FUNCNUM_MASK GENMASK(10, 8) #define PLX_DMCFGA_TO_FUNCNUM(r) (((r) & PLX_DMCFGA_FUNCNUM_MASK) >> 8) /* Device Number */ #define PLX_DMCFGA_DEVNUM(x) (BIT(11) * ((x) & 0x1f)) #define PLX_DMCFGA_DEVNUM_MASK GENMASK(15, 11) #define PLX_DMCFGA_TO_DEVNUM(r) (((r) & PLX_DMCFGA_DEVNUM_MASK) >> 11) /* Bus Number */ #define PLX_DMCFGA_BUSNUM(x) (BIT(16) * ((x) & 0xff)) #define PLX_DMCFGA_BUSNUM_MASK GENMASK(23, 16) #define PLX_DMCFGA_TO_BUSNUM(r) (((r) & PLX_DMCFGA_BUSNUM_MASK) >> 16) /* Configuration Enable */ #define PLX_DMCFGA_CONFIGEN BIT(31) /* * Mailbox Register N (N <= 7) * * Note that if the I2O feature is enabled (QSR[0] is set), Mailbox Register 0 * is replaced by the Inbound Queue Port, and Mailbox Register 1 is replaced * by the Outbound Queue Port. However, Mailbox Register 0 and 1 are always * accessible at alternative offsets if the I2O feature is enabled. */ #define PLX_REG_MBOX(n) (0x0040 + (n) * 4) #define PLX_REG_MBOX0 PLX_REG_MBOX(0) #define PLX_REG_MBOX1 PLX_REG_MBOX(1) #define PLX_REG_MBOX2 PLX_REG_MBOX(2) #define PLX_REG_MBOX3 PLX_REG_MBOX(3) #define PLX_REG_MBOX4 PLX_REG_MBOX(4) #define PLX_REG_MBOX5 PLX_REG_MBOX(5) #define PLX_REG_MBOX6 PLX_REG_MBOX(6) #define PLX_REG_MBOX7 PLX_REG_MBOX(7) /* Alternative offsets for Mailbox Registers 0 and 1 (in case I2O is enabled) */ #define PLX_REG_ALT_MBOX(n) ((n) < 2 ? 0x0078 + (n) * 4 : PLX_REG_MBOX(n)) #define PLX_REG_ALT_MBOX0 PLX_REG_ALT_MBOX(0) #define PLX_REG_ALT_MBOX1 PLX_REG_ALT_MBOX(1) /* PCI-to-Local Doorbell Register */ #define PLX_REG_P2LDBELL 0x0060 /* Local-to-PCI Doorbell Register */ #define PLX_REG_L2PDBELL 0x0064 /* Interrupt Control/Status Register */ #define PLX_REG_INTCSR 0x0068 /* Enable Local Bus LSERR# when PCI Bus Target Abort or Master Abort occurs */ #define PLX_INTCSR_LSEABORTEN BIT(0) /* Enable Local Bus LSERR# when PCI parity error occurs */ #define PLX_INTCSR_LSEPARITYEN BIT(1) /* Generate PCI Bus SERR# when set to 1 */ #define PLX_INTCSR_GENSERR BIT(2) /* Mailbox Interrupt Enable (local bus interrupts on PCI write to MBOX0-3) */ #define PLX_INTCSR_MBIEN BIT(3) /* PCI Interrupt Enable */ #define PLX_INTCSR_PIEN BIT(8) /* PCI Doorbell Interrupt Enable */ #define PLX_INTCSR_PDBIEN BIT(9) /* PCI Abort Interrupt Enable */ #define PLX_INTCSR_PABORTIEN BIT(10) /* PCI Local Interrupt Enable */ #define PLX_INTCSR_PLIEN BIT(11) /* Retry Abort Enable (for diagnostic purposes only) */ #define PLX_INTCSR_RAEN BIT(12) /* PCI Doorbell Interrupt Active (read-only) */ #define PLX_INTCSR_PDBIA BIT(13) /* PCI Abort Interrupt Active (read-only) */ #define PLX_INTCSR_PABORTIA BIT(14) /* Local Interrupt (LINTi#) Active (read-only) */ #define PLX_INTCSR_PLIA BIT(15) /* Local Interrupt Output (LINTo#) Enable */ #define PLX_INTCSR_LIOEN BIT(16) /* Local Doorbell Interrupt Enable */ #define PLX_INTCSR_LDBIEN BIT(17) /* DMA Channel 0 Interrupt Enable */ #define PLX_INTCSR_DMA0IEN BIT(18) /* DMA Channel 1 Interrupt Enable */ #define PLX_INTCSR_DMA1IEN BIT(19) /* DMA Channel N Interrupt Enable (N <= 1) */ #define PLX_INTCSR_DMAIEN(n) ((n) ? PLX_INTCSR_DMA1IEN : PLX_INTCSR_DMA0IEN) /* Local Doorbell Interrupt Active (read-only) */ #define PLX_INTCSR_LDBIA BIT(20) /* DMA Channel 0 Interrupt Active (read-only) */ #define PLX_INTCSR_DMA0IA BIT(21) /* DMA Channel 1 Interrupt Active (read-only) */ #define PLX_INTCSR_DMA1IA BIT(22) /* DMA Channel N Interrupt Active (N <= 1) (read-only) */ #define PLX_INTCSR_DMAIA(n) ((n) ? PLX_INTCSR_DMA1IA : PLX_INTCSR_DMA0IA) /* BIST Interrupt Active (read-only) */ #define PLX_INTCSR_BISTIA BIT(23) /* Direct Master Not Bus Master During Master Or Target Abort (read-only) */ #define PLX_INTCSR_ABNOTDM BIT(24) /* DMA Channel 0 Not Bus Master During Master Or Target Abort (read-only) */ #define PLX_INTCSR_ABNOTDMA0 BIT(25) /* DMA Channel 1 Not Bus Master During Master Or Target Abort (read-only) */ #define PLX_INTCSR_ABNOTDMA1 BIT(26) /* DMA Channel N Not Bus Master During Master Or Target Abort (read-only) */ #define PLX_INTCSR_ABNOTDMA(n) ((n) ? PLX_INTCSR_ABNOTDMA1 \ : PLX_INTCSR_ABNOTDMA0) /* Target Abort Not Generated After 256 Master Retries (read-only) */ #define PLX_INTCSR_ABNOTRETRY BIT(27) /* PCI Wrote Mailbox 0 (enabled if bit 3 set) (read-only) */ #define PLX_INTCSR_MB0IA BIT(28) /* PCI Wrote Mailbox 1 (enabled if bit 3 set) (read-only) */ #define PLX_INTCSR_MB1IA BIT(29) /* PCI Wrote Mailbox 2 (enabled if bit 3 set) (read-only) */ #define PLX_INTCSR_MB2IA BIT(30) /* PCI Wrote Mailbox 3 (enabled if bit 3 set) (read-only) */ #define PLX_INTCSR_MB3IA BIT(31) /* PCI Wrote Mailbox N (N <= 3) (enabled if bit 3 set) (read-only) */ #define PLX_INTCSR_MBIA(n) BIT(28 + (n)) /* * Serial EEPROM Control, PCI Command Codes, User I/O Control, * Init Control Register */ #define PLX_REG_CNTRL 0x006c /* PCI Read Command Code For DMA */ #define PLX_CNTRL_CCRDMA(x) (BIT(0) * ((x) & 0xf)) #define PLX_CNTRL_CCRDMA_MASK GENMASK(3, 0) #define PLX_CNTRL_TO_CCRDMA(r) ((r) & PLX_CNTRL_CCRDMA_MASK) #define PLX_CNTRL_CCRDMA_NORMAL PLX_CNTRL_CCRDMA(14) /* value after reset */ /* PCI Write Command Code For DMA 0 */ #define PLX_CNTRL_CCWDMA(x) (BIT(4) * ((x) & 0xf)) #define PLX_CNTRL_CCWDMA_MASK GENMASK(7, 4) #define PLX_CNTRL_TO_CCWDMA(r) (((r) & PLX_CNTRL_CCWDMA_MASK) >> 4) #define PLX_CNTRL_CCWDMA_NORMAL PLX_CNTRL_CCWDMA(7) /* value after reset */ /* PCI Memory Read Command Code For Direct Master */ #define PLX_CNTRL_CCRDM(x) (BIT(8) * ((x) & 0xf)) #define PLX_CNTRL_CCRDM_MASK GENMASK(11, 8) #define PLX_CNTRL_TO_CCRDM(r) (((r) & PLX_CNTRL_CCRDM_MASK) >> 8) #define PLX_CNTRL_CCRDM_NORMAL PLX_CNTRL_CCRDM(6) /* value after reset */ /* PCI Memory Write Command Code For Direct Master */ #define PLX_CNTRL_CCWDM(x) (BIT(12) * ((x) & 0xf)) #define PLX_CNTRL_CCWDM_MASK GENMASK(15, 12) #define PLX_CNTRL_TO_CCWDM(r) (((r) & PLX_CNTRL_CCWDM_MASK) >> 12) #define PLX_CNTRL_CCWDM_NORMAL PLX_CNTRL_CCWDM(7) /* value after reset */ /* General Purpose Output (USERO) */ #define PLX_CNTRL_USERO BIT(16) /* General Purpose Input (USERI) (read-only) */ #define PLX_CNTRL_USERI BIT(17) /* Serial EEPROM Clock Output (EESK) */ #define PLX_CNTRL_EESK BIT(24) /* Serial EEPROM Chip Select Output (EECS) */ #define PLX_CNTRL_EECS BIT(25) /* Serial EEPROM Data Write Bit (EEDI (sic)) */ #define PLX_CNTRL_EEWB BIT(26) /* Serial EEPROM Data Read Bit (EEDO (sic)) (read-only) */ #define PLX_CNTRL_EERB BIT(27) /* Serial EEPROM Present (read-only) */ #define PLX_CNTRL_EEPRESENT BIT(28) /* Reload Configuration Registers from EEPROM */ #define PLX_CNTRL_EERELOAD BIT(29) /* PCI Adapter Software Reset (asserts LRESETo#) */ #define PLX_CNTRL_RESET BIT(30) /* Local Init Status (read-only) */ #define PLX_CNTRL_INITDONE BIT(31) /* * Combined command code stuff for convenience. */ #define PLX_CNTRL_CC_MASK \ (PLX_CNTRL_CCRDMA_MASK | PLX_CNTRL_CCWDMA_MASK | \ PLX_CNTRL_CCRDM_MASK | PLX_CNTRL_CCWDM_MASK) #define PLX_CNTRL_CC_NORMAL \ (PLX_CNTRL_CCRDMA_NORMAL | PLX_CNTRL_CCWDMA_NORMAL | \ PLX_CNTRL_CCRDM_NORMAL | PLX_CNTRL_CCWDM_NORMAL) /* val after reset */ /* PCI Permanent Configuration ID Register (hard-coded PLX vendor and device) */ #define PLX_REG_PCIHIDR 0x0070 /* Hard-coded ID for PLX PCI 9080 */ #define PLX_PCIHIDR_9080 0x908010b5 /* PCI Permanent Revision ID Register (hard-coded silicon revision) (8-bit). */ #define PLX_REG_PCIHREV 0x0074 /* DMA Channel N Mode Register (N <= 1) */ #define PLX_REG_DMAMODE(n) ((n) ? PLX_REG_DMAMODE1 : PLX_REG_DMAMODE0) #define PLX_REG_DMAMODE0 0x0080 #define PLX_REG_DMAMODE1 0x0094 /* Local Bus Width */ #define PLX_DMAMODE_WIDTH_8 (BIT(0) * 0) /* 8 bits wide */ #define PLX_DMAMODE_WIDTH_16 (BIT(0) * 1) /* 16 bits wide */ #define PLX_DMAMODE_WIDTH_32 (BIT(0) * 2) /* 32 bits wide */ #define PLX_DMAMODE_WIDTH_32A (BIT(0) * 3) /* 32 bits wide */ #define PLX_DMAMODE_WIDTH_MASK GENMASK(1, 0) /* Internal Wait States */ #define PLX_DMAMODE_IWS(x) (BIT(2) * ((x) & 0xf)) #define PLX_DMAMODE_IWS_MASK GENMASK(5, 2) #define PLX_DMAMODE_TO_IWS(r) (((r) & PLX_DMAMODE_IWS_MASK) >> 2) /* Ready Input Enable */ #define PLX_DMAMODE_READYIEN BIT(6) /* BTERM# Input Enable */ #define PLX_DMAMODE_BTERMIEN BIT(7) /* Local Burst Enable */ #define PLX_DMAMODE_BURSTEN BIT(8) /* Chaining Enable */ #define PLX_DMAMODE_CHAINEN BIT(9) /* Done Interrupt Enable */ #define PLX_DMAMODE_DONEIEN BIT(10) /* Hold Local Address Constant */ #define PLX_DMAMODE_LACONST BIT(11) /* Demand Mode */ #define PLX_DMAMODE_DEMAND BIT(12) /* Write And Invalidate Mode */ #define PLX_DMAMODE_WINVALIDATE BIT(13) /* DMA EOT Enable - enables EOT0# or EOT1# input pin */ #define PLX_DMAMODE_EOTEN BIT(14) /* DMA Stop Data Transfer Mode - 0:BLAST; 1:EOT asserted or DREQ deasserted */ #define PLX_DMAMODE_STOP BIT(15) /* DMA Clear Count Mode - count in descriptor cleared on completion */ #define PLX_DMAMODE_CLRCOUNT BIT(16) /* DMA Channel Interrupt Select - 0:local bus interrupt; 1:PCI interrupt */ #define PLX_DMAMODE_INTRPCI BIT(17) /* DMA Channel N PCI Address Register (N <= 1) */ #define PLX_REG_DMAPADR(n) ((n) ? PLX_REG_DMAPADR1 : PLX_REG_DMAPADR0) #define PLX_REG_DMAPADR0 0x0084 #define PLX_REG_DMAPADR1 0x0098 /* DMA Channel N Local Address Register (N <= 1) */ #define PLX_REG_DMALADR(n) ((n) ? PLX_REG_DMALADR1 : PLX_REG_DMALADR0) #define PLX_REG_DMALADR0 0x0088 #define PLX_REG_DMALADR1 0x009c /* DMA Channel N Transfer Size (Bytes) Register (N <= 1) (first 23 bits) */ #define PLX_REG_DMASIZ(n) ((n) ? PLX_REG_DMASIZ1 : PLX_REG_DMASIZ0) #define PLX_REG_DMASIZ0 0x008c #define PLX_REG_DMASIZ1 0x00a0 /* DMA Channel N Descriptor Pointer Register (N <= 1) */ #define PLX_REG_DMADPR(n) ((n) ? PLX_REG_DMADPR1 : PLX_REG_DMADPR0) #define PLX_REG_DMADPR0 0x0090 #define PLX_REG_DMADPR1 0x00a4 /* Descriptor Located In PCI Address Space (not local address space) */ #define PLX_DMADPR_DESCPCI BIT(0) /* End Of Chain */ #define PLX_DMADPR_CHAINEND BIT(1) /* Interrupt After Terminal Count */ #define PLX_DMADPR_TCINTR BIT(2) /* Direction Of Transfer Local Bus To PCI (not PCI to local) */ #define PLX_DMADPR_XFERL2P BIT(3) /* Next Descriptor Address Bits 31:4 (16 byte boundary) */ #define PLX_DMADPR_NEXT_MASK GENMASK(31, 4) /* DMA Channel N Command/Status Register (N <= 1) (8-bit) */ #define PLX_REG_DMACSR(n) ((n) ? PLX_REG_DMACSR1 : PLX_REG_DMACSR0) #define PLX_REG_DMACSR0 0x00a8 #define PLX_REG_DMACSR1 0x00a9 /* Channel Enable */ #define PLX_DMACSR_ENABLE BIT(0) /* Channel Start - write 1 to start transfer (write-only) */ #define PLX_DMACSR_START BIT(1) /* Channel Abort - write 1 to abort transfer (write-only) */ #define PLX_DMACSR_ABORT BIT(2) /* Clear Interrupt - write 1 to clear DMA Channel Interrupt (write-only) */ #define PLX_DMACSR_CLEARINTR BIT(3) /* Channel Done - transfer complete/inactive (read-only) */ #define PLX_DMACSR_DONE BIT(4) /* DMA Threshold Register */ #define PLX_REG_DMATHR 0x00b0 /* * DMA Threshold constraints: * (C0PLAF + 1) + (C0PLAE + 1) <= 32 * (C0LPAF + 1) + (C0LPAE + 1) <= 32 * (C1PLAF + 1) + (C1PLAE + 1) <= 16 * (C1LPAF + 1) + (C1LPAE + 1) <= 16 */ /* DMA Channel 0 PCI-to-Local Almost Full (divided by 2, minus 1) */ #define PLX_DMATHR_C0PLAF(x) (BIT(0) * ((x) & 0xf)) #define PLX_DMATHR_C0PLAF_MASK GENMASK(3, 0) #define PLX_DMATHR_TO_C0PLAF(r) ((r) & PLX_DMATHR_C0PLAF_MASK) /* DMA Channel 0 Local-to-PCI Almost Empty (divided by 2, minus 1) */ #define PLX_DMATHR_C0LPAE(x) (BIT(4) * ((x) & 0xf)) #define PLX_DMATHR_C0LPAE_MASK GENMASK(7, 4) #define PLX_DMATHR_TO_C0LPAE(r) (((r) & PLX_DMATHR_C0LPAE_MASK) >> 4) /* DMA Channel 0 Local-to-PCI Almost Full (divided by 2, minus 1) */ #define PLX_DMATHR_C0LPAF(x) (BIT(8) * ((x) & 0xf)) #define PLX_DMATHR_C0LPAF_MASK GENMASK(11, 8) #define PLX_DMATHR_TO_C0LPAF(r) (((r) & PLX_DMATHR_C0LPAF_MASK) >> 8) /* DMA Channel 0 PCI-to-Local Almost Empty (divided by 2, minus 1) */ #define PLX_DMATHR_C0PLAE(x) (BIT(12) * ((x) & 0xf)) #define PLX_DMATHR_C0PLAE_MASK GENMASK(15, 12) #define PLX_DMATHR_TO_C0PLAE(r) (((r) & PLX_DMATHR_C0PLAE_MASK) >> 12) /* DMA Channel 1 PCI-to-Local Almost Full (divided by 2, minus 1) */ #define PLX_DMATHR_C1PLAF(x) (BIT(16) * ((x) & 0xf)) #define PLX_DMATHR_C1PLAF_MASK GENMASK(19, 16) #define PLX_DMATHR_TO_C1PLAF(r) (((r) & PLX_DMATHR_C1PLAF_MASK) >> 16) /* DMA Channel 1 Local-to-PCI Almost Empty (divided by 2, minus 1) */ #define PLX_DMATHR_C1LPAE(x) (BIT(20) * ((x) & 0xf)) #define PLX_DMATHR_C1LPAE_MASK GENMASK(23, 20) #define PLX_DMATHR_TO_C1LPAE(r) (((r) & PLX_DMATHR_C1LPAE_MASK) >> 20) /* DMA Channel 1 Local-to-PCI Almost Full (divided by 2, minus 1) */ #define PLX_DMATHR_C1LPAF(x) (BIT(24) * ((x) & 0xf)) #define PLX_DMATHR_C1LPAF_MASK GENMASK(27, 24) #define PLX_DMATHR_TO_C1LPAF(r) (((r) & PLX_DMATHR_C1LPAF_MASK) >> 24) /* DMA Channel 1 PCI-to-Local Almost Empty (divided by 2, minus 1) */ #define PLX_DMATHR_C1PLAE(x) (BIT(28) * ((x) & 0xf)) #define PLX_DMATHR_C1PLAE_MASK GENMASK(31, 28) #define PLX_DMATHR_TO_C1PLAE(r) (((r) & PLX_DMATHR_C1PLAE_MASK) >> 28) /* * Messaging Queue Registers OPLFIS, OPLFIM, IQP, OQP, MQCR, QBAR, IFHPR, * IFTPR, IPHPR, IPTPR, OFHPR, OFTPR, OPHPR, OPTPR, and QSR have been omitted. * They are used by the I2O feature. (IQP and OQP occupy the usual offsets of * the MBOX0 and MBOX1 registers if the I2O feature is enabled, but MBOX0 and * MBOX1 are accessible via alternative offsets. */ /* Queue Status/Control Register */ #define PLX_REG_QSR 0x00e8 /* Value of QSR after reset - disables I2O feature completely. */ #define PLX_QSR_VALUE_AFTER_RESET 0x00000050 /* * Accesses near the end of memory can cause the PLX chip * to pre-fetch data off of end-of-ram. Limit the size of * memory so host-side accesses cannot occur. */ #define PLX_PREFETCH 32 /** * plx9080_abort_dma - Abort a PLX PCI 9080 DMA transfer * @iobase: Remapped base address of configuration registers. * @channel: DMA channel number (0 or 1). * * Aborts the DMA transfer on the channel, which must have been enabled * and started beforehand. * * Return: * %0 on success. * -%ETIMEDOUT if timed out waiting for abort to complete. */ static inline int plx9080_abort_dma(void __iomem *iobase, unsigned int channel) { void __iomem *dma_cs_addr; u8 dma_status; const int timeout = 10000; unsigned int i; dma_cs_addr = iobase + PLX_REG_DMACSR(channel); /* abort dma transfer if necessary */ dma_status = readb(dma_cs_addr); if ((dma_status & PLX_DMACSR_ENABLE) == 0) return 0; /* wait to make sure done bit is zero */ for (i = 0; (dma_status & PLX_DMACSR_DONE) && i < timeout; i++) { udelay(1); dma_status = readb(dma_cs_addr); } if (i == timeout) return -ETIMEDOUT; /* disable and abort channel */ writeb(PLX_DMACSR_ABORT, dma_cs_addr); /* wait for dma done bit */ dma_status = readb(dma_cs_addr); for (i = 0; (dma_status & PLX_DMACSR_DONE) == 0 && i < timeout; i++) { udelay(1); dma_status = readb(dma_cs_addr); } if (i == timeout) return -ETIMEDOUT; return 0; } #endif /* __COMEDI_PLX9080_H */