summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/iwlwifi/iwl-4965-hw.h
blob: ffe1e9dfdec7bc5da5b2e0c909a41f7f710c4a8d (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
1257
1258
1259
1260
1261
1262
1263
1264
1265
1266
1267
1268
1269
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342
1343
1344
1345
1346
1347
1348
1349
1350
1351
1352
1353
1354
1355
1356
1357
1358
1359
1360
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1387
1388
1389
1390
1391
1392
1393
1394
1395
1396
1397
1398
1399
1400
1401
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416
1417
1418
1419
1420
1421
1422
1423
1424
1425
1426
1427
1428
1429
1430
1431
1432
1433
1434
1435
1436
1437
1438
1439
1440
1441
1442
1443
1444
1445
1446
1447
1448
1449
1450
1451
1452
1453
1454
1455
1456
1457
1458
1459
1460
1461
1462
1463
1464
1465
1466
1467
1468
1469
1470
1471
1472
1473
1474
1475
1476
1477
1478
1479
1480
1481
1482
1483
1484
1485
1486
1487
1488
1489
1490
1491
1492
1493
1494
1495
1496
1497
1498
1499
1500
1501
1502
1503
1504
1505
1506
1507
1508
1509
1510
1511
1512
1513
1514
1515
1516
1517
1518
1519
1520
1521
1522
1523
1524
1525
1526
1527
1528
1529
1530
1531
1532
1533
1534
1535
1536
1537
1538
1539
1540
1541
1542
1543
1544
1545
1546
1547
1548
1549
1550
1551
1552
1553
1554
1555
1556
1557
1558
1559
1560
1561
1562
1563
1564
1565
1566
1567
1568
1569
1570
1571
1572
1573
1574
1575
1576
1577
1578
1579
1580
1581
1582
1583
1584
1585
1586
1587
1588
1589
1590
1591
1592
1593
1594
1595
1596
1597
1598
1599
1600
1601
1602
1603
1604
1605
1606
1607
1608
1609
1610
1611
1612
1613
1614
1615
1616
1617
1618
1619
1620
1621
1622
1623
1624
1625
1626
1627
1628
1629
1630
1631
1632
1633
1634
1635
1636
1637
1638
1639
1640
1641
1642
1643
1644
1645
1646
1647
1648
1649
1650
1651
1652
1653
1654
1655
1656
1657
1658
1659
1660
1661
1662
1663
1664
1665
1666
1667
1668
1669
1670
1671
1672
1673
1674
1675
1676
1677
1678
1679
1680
1681
1682
1683
1684
1685
1686
1687
1688
1689
1690
1691
1692
1693
1694
1695
1696
1697
1698
1699
1700
1701
1702
1703
1704
1705
1706
1707
1708
1709
1710
1711
1712
1713
1714
1715
1716
1717
1718
1719
1720
1721
1722
1723
1724
1725
1726
1727
1728
1729
1730
1731
1732
1733
1734
1735
1736
1737
1738
1739
1740
1741
1742
1743
1744
1745
1746
1747
1748
1749
1750
1751
1752
1753
1754
1755
1756
1757
1758
1759
1760
1761
1762
1763
1764
1765
1766
1767
1768
1769
1770
1771
1772
1773
1774
1775
1776
1777
1778
1779
1780
1781
1782
1783
1784
1785
1786
1787
1788
1789
1790
1791
1792
1793
1794
1795
1796
1797
1798
1799
1800
1801
1802
1803
1804
1805
1806
1807
1808
1809
1810
1811
1812
1813
1814
1815
1816
1817
1818
1819
1820
1821
1822
1823
1824
1825
1826
1827
1828
1829
1830
1831
1832
1833
1834
1835
1836
1837
1838
1839
1840
1841
1842
1843
1844
1845
1846
1847
1848
1849
1850
1851
1852
1853
1854
1855
1856
1857
1858
1859
1860
1861
1862
1863
1864
1865
1866
1867
1868
1869
1870
1871
1872
1873
1874
1875
1876
1877
1878
1879
1880
1881
1882
1883
1884
1885
1886
1887
1888
1889
1890
1891
1892
1893
1894
1895
1896
1897
1898
1899
1900
1901
1902
1903
1904
1905
1906
1907
1908
1909
1910
1911
1912
1913
1914
1915
1916
1917
1918
1919
1920
1921
1922
1923
1924
1925
1926
1927
1928
1929
1930
1931
1932
1933
1934
1935
1936
1937
1938
1939
1940
1941
1942
1943
1944
1945
1946
1947
1948
1949
1950
1951
1952
1953
1954
1955
1956
1957
1958
1959
1960
1961
1962
1963
1964
1965
1966
1967
1968
1969
1970
1971
1972
1973
1974
1975
1976
1977
1978
1979
1980
1981
1982
1983
1984
1985
1986
1987
1988
1989
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
2025
2026
2027
2028
2029
2030
2031
2032
2033
2034
2035
2036
2037
2038
2039
2040
2041
2042
2043
2044
2045
2046
2047
2048
2049
2050
2051
2052
2053
2054
2055
2056
2057
2058
2059
2060
2061
2062
2063
2064
2065
2066
2067
2068
2069
2070
2071
2072
2073
/******************************************************************************
 *
 * This file is provided under a dual BSD/GPLv2 license.  When using or
 * redistributing this file, you may do so under either license.
 *
 * GPL LICENSE SUMMARY
 *
 * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of version 2 of the GNU General Public License as
 * published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful, but
 * WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 * General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110,
 * USA
 *
 * The full GNU General Public License is included in this distribution
 * in the file called LICENSE.GPL.
 *
 * Contact Information:
 * James P. Ketrenos <ipw2100-admin@linux.intel.com>
 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
 *
 * BSD LICENSE
 *
 * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved.
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 *  * Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 *  * Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 *  * Neither the name Intel Corporation nor the names of its
 *    contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *
 *****************************************************************************/
/*
 * Please use this file (iwl-4965-hw.h) only for hardware-related definitions.
 * Use iwl-4965-commands.h for uCode API definitions.
 * Use iwl-4965.h for driver implementation definitions.
 */

#ifndef __iwl_4965_hw_h__
#define __iwl_4965_hw_h__

/*
 * uCode queue management definitions ...
 * Queue #4 is the command queue for 3945 and 4965; map it to Tx FIFO chnl 4.
 * The first queue used for block-ack aggregation is #7 (4965 only).
 * All block-ack aggregation queues should map to Tx DMA/FIFO channel 7.
 */
#define IWL_CMD_QUEUE_NUM       4
#define IWL_CMD_FIFO_NUM        4
#define IWL_BACK_QUEUE_FIRST_ID 7

/* Tx rates */
#define IWL_CCK_RATES 4
#define IWL_OFDM_RATES 8
#define IWL_HT_RATES 16
#define IWL_MAX_RATES  (IWL_CCK_RATES+IWL_OFDM_RATES+IWL_HT_RATES)

/* Time constants */
#define SHORT_SLOT_TIME 9
#define LONG_SLOT_TIME 20

/* RSSI to dBm */
#define IWL_RSSI_OFFSET	44

/*
 * EEPROM related constants, enums, and structures.
 */

/*
 * EEPROM access time values:
 *
 * Driver initiates EEPROM read by writing byte address << 1 to CSR_EEPROM_REG,
 *   then clearing (with subsequent read/modify/write) CSR_EEPROM_REG bit
 *   CSR_EEPROM_REG_BIT_CMD (0x2).
 * Driver then polls CSR_EEPROM_REG for CSR_EEPROM_REG_READ_VALID_MSK (0x1).
 * When polling, wait 10 uSec between polling loops, up to a maximum 5000 uSec.
 * Driver reads 16-bit value from bits 31-16 of CSR_EEPROM_REG.
 */
#define IWL_EEPROM_ACCESS_TIMEOUT	5000 /* uSec */
#define IWL_EEPROM_ACCESS_DELAY		10   /* uSec */

/*
 * Regulatory channel usage flags in EEPROM struct iwl4965_eeprom_channel.flags.
 *
 * IBSS and/or AP operation is allowed *only* on those channels with
 * (VALID && IBSS && ACTIVE && !RADAR).  This restriction is in place because
 * RADAR detection is not supported by the 4965 driver, but is a
 * requirement for establishing a new network for legal operation on channels
 * requiring RADAR detection or restricting ACTIVE scanning.
 *
 * NOTE:  "WIDE" flag does not indicate anything about "FAT" 40 MHz channels.
 *        It only indicates that 20 MHz channel use is supported; FAT channel
 *        usage is indicated by a separate set of regulatory flags for each
 *        FAT channel pair.
 *
 * NOTE:  Using a channel inappropriately will result in a uCode error!
 */
enum {
	EEPROM_CHANNEL_VALID = (1 << 0),	/* usable for this SKU/geo */
	EEPROM_CHANNEL_IBSS = (1 << 1),		/* usable as an IBSS channel */
	/* Bit 2 Reserved */
	EEPROM_CHANNEL_ACTIVE = (1 << 3),	/* active scanning allowed */
	EEPROM_CHANNEL_RADAR = (1 << 4),	/* radar detection required */
	EEPROM_CHANNEL_WIDE = (1 << 5),		/* 20 MHz channel okay */
	EEPROM_CHANNEL_NARROW = (1 << 6),	/* 10 MHz channel (not used) */
	EEPROM_CHANNEL_DFS = (1 << 7),	/* dynamic freq selection candidate */
};

/* SKU Capabilities */
#define EEPROM_SKU_CAP_SW_RF_KILL_ENABLE                (1 << 0)
#define EEPROM_SKU_CAP_HW_RF_KILL_ENABLE                (1 << 1)

/* *regulatory* channel data format in eeprom, one for each channel.
 * There are separate entries for FAT (40 MHz) vs. normal (20 MHz) channels. */
struct iwl4965_eeprom_channel {
	u8 flags;		/* EEPROM_CHANNEL_* flags copied from EEPROM */
	s8 max_power_avg;	/* max power (dBm) on this chnl, limit 31 */
} __attribute__ ((packed));

/* 4965 has two radio transmitters (and 3 radio receivers) */
#define EEPROM_TX_POWER_TX_CHAINS      (2)

/* 4965 has room for up to 8 sets of txpower calibration data */
#define EEPROM_TX_POWER_BANDS          (8)

/* 4965 factory calibration measures txpower gain settings for
 * each of 3 target output levels */
#define EEPROM_TX_POWER_MEASUREMENTS   (3)

/* 4965 driver does not work with txpower calibration version < 5.
 * Look for this in calib_version member of struct iwl4965_eeprom. */
#define EEPROM_TX_POWER_VERSION_NEW    (5)


/*
 * 4965 factory calibration data for one txpower level, on one channel,
 * measured on one of the 2 tx chains (radio transmitter and associated
 * antenna).  EEPROM contains:
 *
 * 1)  Temperature (degrees Celsius) of device when measurement was made.
 *
 * 2)  Gain table index used to achieve the target measurement power.
 *     This refers to the "well-known" gain tables (see iwl-4965-hw.h).
 *
 * 3)  Actual measured output power, in half-dBm ("34" = 17 dBm).
 *
 * 4)  RF power amplifier detector level measurement (not used).
 */
struct iwl4965_eeprom_calib_measure {
	u8 temperature;		/* Device temperature (Celsius) */
	u8 gain_idx;		/* Index into gain table */
	u8 actual_pow;		/* Measured RF output power, half-dBm */
	s8 pa_det;		/* Power amp detector level (not used) */
} __attribute__ ((packed));


/*
 * 4965 measurement set for one channel.  EEPROM contains:
 *
 * 1)  Channel number measured
 *
 * 2)  Measurements for each of 3 power levels for each of 2 radio transmitters
 *     (a.k.a. "tx chains") (6 measurements altogether)
 */
struct iwl4965_eeprom_calib_ch_info {
	u8 ch_num;
	struct iwl4965_eeprom_calib_measure measurements[EEPROM_TX_POWER_TX_CHAINS]
		[EEPROM_TX_POWER_MEASUREMENTS];
} __attribute__ ((packed));

/*
 * 4965 txpower subband info.
 *
 * For each frequency subband, EEPROM contains the following:
 *
 * 1)  First and last channels within range of the subband.  "0" values
 *     indicate that this sample set is not being used.
 *
 * 2)  Sample measurement sets for 2 channels close to the range endpoints.
 */
struct iwl4965_eeprom_calib_subband_info {
	u8 ch_from;	/* channel number of lowest channel in subband */
	u8 ch_to;	/* channel number of highest channel in subband */
	struct iwl4965_eeprom_calib_ch_info ch1;
	struct iwl4965_eeprom_calib_ch_info ch2;
} __attribute__ ((packed));


/*
 * 4965 txpower calibration info.  EEPROM contains:
 *
 * 1)  Factory-measured saturation power levels (maximum levels at which
 *     tx power amplifier can output a signal without too much distortion).
 *     There is one level for 2.4 GHz band and one for 5 GHz band.  These
 *     values apply to all channels within each of the bands.
 *
 * 2)  Factory-measured power supply voltage level.  This is assumed to be
 *     constant (i.e. same value applies to all channels/bands) while the
 *     factory measurements are being made.
 *
 * 3)  Up to 8 sets of factory-measured txpower calibration values.
 *     These are for different frequency ranges, since txpower gain
 *     characteristics of the analog radio circuitry vary with frequency.
 *
 *     Not all sets need to be filled with data;
 *     struct iwl4965_eeprom_calib_subband_info contains range of channels
 *     (0 if unused) for each set of data.
 */
struct iwl4965_eeprom_calib_info {
	u8 saturation_power24;	/* half-dBm (e.g. "34" = 17 dBm) */
	u8 saturation_power52;	/* half-dBm */
	s16 voltage;		/* signed */
	struct iwl4965_eeprom_calib_subband_info band_info[EEPROM_TX_POWER_BANDS];
} __attribute__ ((packed));


/*
 * 4965 EEPROM map
 */
struct iwl4965_eeprom {
	u8 reserved0[16];
#define EEPROM_DEVICE_ID                    (2*0x08)	/* 2 bytes */
	u16 device_id;		/* abs.ofs: 16 */
	u8 reserved1[2];
#define EEPROM_PMC                          (2*0x0A)	/* 2 bytes */
	u16 pmc;		/* abs.ofs: 20 */
	u8 reserved2[20];
#define EEPROM_MAC_ADDRESS                  (2*0x15)	/* 6  bytes */
	u8 mac_address[6];	/* abs.ofs: 42 */
	u8 reserved3[58];
#define EEPROM_BOARD_REVISION               (2*0x35)	/* 2  bytes */
	u16 board_revision;	/* abs.ofs: 106 */
	u8 reserved4[11];
#define EEPROM_BOARD_PBA_NUMBER             (2*0x3B+1)	/* 9  bytes */
	u8 board_pba_number[9];	/* abs.ofs: 119 */
	u8 reserved5[8];
#define EEPROM_VERSION                      (2*0x44)	/* 2  bytes */
	u16 version;		/* abs.ofs: 136 */
#define EEPROM_SKU_CAP                      (2*0x45)	/* 1  bytes */
	u8 sku_cap;		/* abs.ofs: 138 */
#define EEPROM_LEDS_MODE                    (2*0x45+1)	/* 1  bytes */
	u8 leds_mode;		/* abs.ofs: 139 */
#define EEPROM_OEM_MODE                     (2*0x46)	/* 2  bytes */
	u16 oem_mode;
#define EEPROM_WOWLAN_MODE                  (2*0x47)	/* 2  bytes */
	u16 wowlan_mode;	/* abs.ofs: 142 */
#define EEPROM_LEDS_TIME_INTERVAL           (2*0x48)	/* 2  bytes */
	u16 leds_time_interval;	/* abs.ofs: 144 */
#define EEPROM_LEDS_OFF_TIME                (2*0x49)	/* 1  bytes */
	u8 leds_off_time;	/* abs.ofs: 146 */
#define EEPROM_LEDS_ON_TIME                 (2*0x49+1)	/* 1  bytes */
	u8 leds_on_time;	/* abs.ofs: 147 */
#define EEPROM_ALMGOR_M_VERSION             (2*0x4A)	/* 1  bytes */
	u8 almgor_m_version;	/* abs.ofs: 148 */
#define EEPROM_ANTENNA_SWITCH_TYPE          (2*0x4A+1)	/* 1  bytes */
	u8 antenna_switch_type;	/* abs.ofs: 149 */
	u8 reserved6[8];
#define EEPROM_4965_BOARD_REVISION          (2*0x4F)	/* 2 bytes */
	u16 board_revision_4965;	/* abs.ofs: 158 */
	u8 reserved7[13];
#define EEPROM_4965_BOARD_PBA               (2*0x56+1)	/* 9 bytes */
	u8 board_pba_number_4965[9];	/* abs.ofs: 173 */
	u8 reserved8[10];
#define EEPROM_REGULATORY_SKU_ID            (2*0x60)	/* 4  bytes */
	u8 sku_id[4];		/* abs.ofs: 192 */

/*
 * Per-channel regulatory data.
 *
 * Each channel that *might* be supported by 3945 or 4965 has a fixed location
 * in EEPROM containing EEPROM_CHANNEL_* usage flags (LSB) and max regulatory
 * txpower (MSB).
 *
 * Entries immediately below are for 20 MHz channel width.  FAT (40 MHz)
 * channels (only for 4965, not supported by 3945) appear later in the EEPROM.
 *
 * 2.4 GHz channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
 */
#define EEPROM_REGULATORY_BAND_1            (2*0x62)	/* 2  bytes */
	u16 band_1_count;	/* abs.ofs: 196 */
#define EEPROM_REGULATORY_BAND_1_CHANNELS   (2*0x63)	/* 28 bytes */
	struct iwl4965_eeprom_channel band_1_channels[14]; /* abs.ofs: 196 */

/*
 * 4.9 GHz channels 183, 184, 185, 187, 188, 189, 192, 196,
 * 5.0 GHz channels 7, 8, 11, 12, 16
 * (4915-5080MHz) (none of these is ever supported)
 */
#define EEPROM_REGULATORY_BAND_2            (2*0x71)	/* 2  bytes */
	u16 band_2_count;	/* abs.ofs: 226 */
#define EEPROM_REGULATORY_BAND_2_CHANNELS   (2*0x72)	/* 26 bytes */
	struct iwl4965_eeprom_channel band_2_channels[13]; /* abs.ofs: 228 */

/*
 * 5.2 GHz channels 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64
 * (5170-5320MHz)
 */
#define EEPROM_REGULATORY_BAND_3            (2*0x7F)	/* 2  bytes */
	u16 band_3_count;	/* abs.ofs: 254 */
#define EEPROM_REGULATORY_BAND_3_CHANNELS   (2*0x80)	/* 24 bytes */
	struct iwl4965_eeprom_channel band_3_channels[12]; /* abs.ofs: 256 */

/*
 * 5.5 GHz channels 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140
 * (5500-5700MHz)
 */
#define EEPROM_REGULATORY_BAND_4            (2*0x8C)	/* 2  bytes */
	u16 band_4_count;	/* abs.ofs: 280 */
#define EEPROM_REGULATORY_BAND_4_CHANNELS   (2*0x8D)	/* 22 bytes */
	struct iwl4965_eeprom_channel band_4_channels[11]; /* abs.ofs: 282 */

/*
 * 5.7 GHz channels 145, 149, 153, 157, 161, 165
 * (5725-5825MHz)
 */
#define EEPROM_REGULATORY_BAND_5            (2*0x98)	/* 2  bytes */
	u16 band_5_count;	/* abs.ofs: 304 */
#define EEPROM_REGULATORY_BAND_5_CHANNELS   (2*0x99)	/* 12 bytes */
	struct iwl4965_eeprom_channel band_5_channels[6]; /* abs.ofs: 306 */

	u8 reserved10[2];


/*
 * 2.4 GHz FAT channels 1 (5), 2 (6), 3 (7), 4 (8), 5 (9), 6 (10), 7 (11)
 *
 * The channel listed is the center of the lower 20 MHz half of the channel.
 * The overall center frequency is actually 2 channels (10 MHz) above that,
 * and the upper half of each FAT channel is centered 4 channels (20 MHz) away
 * from the lower half; e.g. the upper half of FAT channel 1 is channel 5,
 * and the overall FAT channel width centers on channel 3.
 *
 * NOTE:  The RXON command uses 20 MHz channel numbers to specify the
 *        control channel to which to tune.  RXON also specifies whether the
 *        control channel is the upper or lower half of a FAT channel.
 *
 * NOTE:  4965 does not support FAT channels on 2.4 GHz.
 */
#define EEPROM_REGULATORY_BAND_24_FAT_CHANNELS (2*0xA0)	/* 14 bytes */
	struct iwl4965_eeprom_channel band_24_channels[7]; /* abs.ofs: 320 */
	u8 reserved11[2];

/*
 * 5.2 GHz FAT channels 36 (40), 44 (48), 52 (56), 60 (64),
 * 100 (104), 108 (112), 116 (120), 124 (128), 132 (136), 149 (153), 157 (161)
 */
#define EEPROM_REGULATORY_BAND_52_FAT_CHANNELS (2*0xA8)	/* 22 bytes */
	struct iwl4965_eeprom_channel band_52_channels[11]; /* abs.ofs: 336 */
	u8 reserved12[6];

/*
 * 4965 driver requires txpower calibration format version 5 or greater.
 * Driver does not work with txpower calibration version < 5.
 * This value is simply a 16-bit number, no major/minor versions here.
 */
#define EEPROM_CALIB_VERSION_OFFSET            (2*0xB6)	/* 2 bytes */
	u16 calib_version;	/* abs.ofs: 364 */
	u8 reserved13[2];
	u8 reserved14[96];	/* abs.ofs: 368 */

/*
 * 4965 Txpower calibration data.
 */
#define EEPROM_IWL_CALIB_TXPOWER_OFFSET        (2*0xE8)	/* 48  bytes */
	struct iwl4965_eeprom_calib_info calib_info;	/* abs.ofs: 464 */

	u8 reserved16[140];	/* fill out to full 1024 byte block */


} __attribute__ ((packed));

#define IWL_EEPROM_IMAGE_SIZE 1024

/* End of EEPROM */

#include "iwl-4965-commands.h"

#define PCI_LINK_CTRL      0x0F0
#define PCI_POWER_SOURCE   0x0C8
#define PCI_REG_WUM8       0x0E8
#define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT         (0x80000000)

/*=== CSR (control and status registers) ===*/
#define CSR_BASE    (0x000)

#define CSR_SW_VER              (CSR_BASE+0x000)
#define CSR_HW_IF_CONFIG_REG    (CSR_BASE+0x000) /* hardware interface config */
#define CSR_INT_COALESCING      (CSR_BASE+0x004) /* accum ints, 32-usec units */
#define CSR_INT                 (CSR_BASE+0x008) /* host interrupt status/ack */
#define CSR_INT_MASK            (CSR_BASE+0x00c) /* host interrupt enable */
#define CSR_FH_INT_STATUS       (CSR_BASE+0x010) /* busmaster int status/ack*/
#define CSR_GPIO_IN             (CSR_BASE+0x018) /* read external chip pins */
#define CSR_RESET               (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/
#define CSR_GP_CNTRL            (CSR_BASE+0x024)

/*
 * Hardware revision info
 * Bit fields:
 * 31-8:  Reserved
 *  7-4:  Type of device:  0x0 = 4965, 0xd = 3945
 *  3-2:  Revision step:  0 = A, 1 = B, 2 = C, 3 = D
 *  1-0:  "Dash" value, as in A-1, etc.
 *
 * NOTE:  Revision step affects calculation of CCK txpower for 4965.
 */
#define CSR_HW_REV              (CSR_BASE+0x028)

/* EEPROM reads */
#define CSR_EEPROM_REG          (CSR_BASE+0x02c)
#define CSR_EEPROM_GP           (CSR_BASE+0x030)
#define CSR_GP_UCODE		(CSR_BASE+0x044)
#define CSR_UCODE_DRV_GP1       (CSR_BASE+0x054)
#define CSR_UCODE_DRV_GP1_SET   (CSR_BASE+0x058)
#define CSR_UCODE_DRV_GP1_CLR   (CSR_BASE+0x05c)
#define CSR_UCODE_DRV_GP2       (CSR_BASE+0x060)
#define CSR_GIO_CHICKEN_BITS    (CSR_BASE+0x100)

/*
 * Indicates hardware rev, to determine CCK backoff for txpower calculation.
 * Bit fields:
 *  3-2:  0 = A, 1 = B, 2 = C, 3 = D step
 */
#define CSR_HW_REV_WA_REG	(CSR_BASE+0x22C)

/* Hardware interface configuration bits */
#define CSR_HW_IF_CONFIG_REG_BIT_KEDRON_R	(0x00000010)
#define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER	(0x00000C00)
#define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI		(0x00000100)
#define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI	(0x00000200)
#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000)

/* interrupt flags in INTA, set by uCode or hardware (e.g. dma),
 * acknowledged (reset) by host writing "1" to flagged bits. */
#define CSR_INT_BIT_FH_RX        (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */
#define CSR_INT_BIT_HW_ERR       (1 << 29) /* DMA hardware error FH_INT[31] */
#define CSR_INT_BIT_DNLD         (1 << 28) /* uCode Download */
#define CSR_INT_BIT_FH_TX        (1 << 27) /* Tx DMA FH_INT[1:0] */
#define CSR_INT_BIT_SCD          (1 << 26) /* TXQ pointer advanced */
#define CSR_INT_BIT_SW_ERR       (1 << 25) /* uCode error */
#define CSR_INT_BIT_RF_KILL      (1 << 7)  /* HW RFKILL switch GP_CNTRL[27] toggled */
#define CSR_INT_BIT_CT_KILL      (1 << 6)  /* Critical temp (chip too hot) rfkill */
#define CSR_INT_BIT_SW_RX        (1 << 3)  /* Rx, command responses, 3945 */
#define CSR_INT_BIT_WAKEUP       (1 << 1)  /* NIC controller waking up (pwr mgmt) */
#define CSR_INT_BIT_ALIVE        (1 << 0)  /* uCode interrupts once it initializes */

#define CSR_INI_SET_MASK	(CSR_INT_BIT_FH_RX   | \
				 CSR_INT_BIT_HW_ERR  | \
				 CSR_INT_BIT_FH_TX   | \
				 CSR_INT_BIT_SW_ERR  | \
				 CSR_INT_BIT_RF_KILL | \
				 CSR_INT_BIT_SW_RX   | \
				 CSR_INT_BIT_WAKEUP  | \
				 CSR_INT_BIT_ALIVE)

/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */
#define CSR_FH_INT_BIT_ERR       (1 << 31) /* Error */
#define CSR_FH_INT_BIT_HI_PRIOR  (1 << 30) /* High priority Rx, bypass coalescing */
#define CSR_FH_INT_BIT_RX_CHNL1  (1 << 17) /* Rx channel 1 */
#define CSR_FH_INT_BIT_RX_CHNL0  (1 << 16) /* Rx channel 0 */
#define CSR_FH_INT_BIT_TX_CHNL1  (1 << 1)  /* Tx channel 1 */
#define CSR_FH_INT_BIT_TX_CHNL0  (1 << 0)  /* Tx channel 0 */

#define CSR_FH_INT_RX_MASK	(CSR_FH_INT_BIT_HI_PRIOR | \
				 CSR_FH_INT_BIT_RX_CHNL1 | \
				 CSR_FH_INT_BIT_RX_CHNL0)

#define CSR_FH_INT_TX_MASK	(CSR_FH_INT_BIT_TX_CHNL1 | \
				 CSR_FH_INT_BIT_TX_CHNL0)


/* RESET */
#define CSR_RESET_REG_FLAG_NEVO_RESET                (0x00000001)
#define CSR_RESET_REG_FLAG_FORCE_NMI                 (0x00000002)
#define CSR_RESET_REG_FLAG_SW_RESET                  (0x00000080)
#define CSR_RESET_REG_FLAG_MASTER_DISABLED           (0x00000100)
#define CSR_RESET_REG_FLAG_STOP_MASTER               (0x00000200)

/* GP (general purpose) CONTROL */
#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY        (0x00000001)
#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE              (0x00000004)
#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ         (0x00000008)
#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP         (0x00000010)

#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN           (0x00000001)

#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE         (0x07000000)
#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE         (0x04000000)
#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW          (0x08000000)


/* EEPROM REG */
#define CSR_EEPROM_REG_READ_VALID_MSK	(0x00000001)
#define CSR_EEPROM_REG_BIT_CMD		(0x00000002)

/* EEPROM GP */
#define CSR_EEPROM_GP_VALID_MSK		(0x00000006)
#define CSR_EEPROM_GP_BAD_SIGNATURE	(0x00000000)
#define CSR_EEPROM_GP_IF_OWNER_MSK	(0x00000180)

/* UCODE DRV GP */
#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP             (0x00000001)
#define CSR_UCODE_SW_BIT_RFKILL                     (0x00000002)
#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED           (0x00000004)
#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT      (0x00000008)

/* GPIO */
#define CSR_GPIO_IN_BIT_AUX_POWER                   (0x00000200)
#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC                (0x00000000)
#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC		CSR_GPIO_IN_BIT_AUX_POWER

/* GI Chicken Bits */
#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX  (0x00800000)
#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER  (0x20000000)

/*=== HBUS (Host-side Bus) ===*/
#define HBUS_BASE	(0x400)

/*
 * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM
 * structures, error log, event log, verifying uCode load).
 * First write to address register, then read from or write to data register
 * to complete the job.  Once the address register is set up, accesses to
 * data registers auto-increment the address by one dword.
 * Bit usage for address registers (read or write):
 *  0-31:  memory address within device
 */
#define HBUS_TARG_MEM_RADDR     (HBUS_BASE+0x00c)
#define HBUS_TARG_MEM_WADDR     (HBUS_BASE+0x010)
#define HBUS_TARG_MEM_WDAT      (HBUS_BASE+0x018)
#define HBUS_TARG_MEM_RDAT      (HBUS_BASE+0x01c)

/*
 * Registers for accessing device's internal peripheral registers
 * (e.g. SCD, BSM, etc.).  First write to address register,
 * then read from or write to data register to complete the job.
 * Bit usage for address registers (read or write):
 *  0-15:  register address (offset) within device
 * 24-25:  (# bytes - 1) to read or write (e.g. 3 for dword)
 */
#define HBUS_TARG_PRPH_WADDR    (HBUS_BASE+0x044)
#define HBUS_TARG_PRPH_RADDR    (HBUS_BASE+0x048)
#define HBUS_TARG_PRPH_WDAT     (HBUS_BASE+0x04c)
#define HBUS_TARG_PRPH_RDAT     (HBUS_BASE+0x050)

/*
 * Per-Tx-queue write pointer (index, really!) (3945 and 4965).
 * Driver sets this to indicate index to next TFD that driver will fill
 * (1 past latest filled).
 * Bit usage:
 *  0-7:  queue write index (0-255)
 * 11-8:  queue selector (0-15)
 */
#define HBUS_TARG_WRPTR         (HBUS_BASE+0x060)

#define HBUS_TARG_MBX_C         (HBUS_BASE+0x030)

#define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED         (0x00000004)

#define TFD_QUEUE_SIZE_MAX      (256)

#define IWL_NUM_SCAN_RATES         (2)

#define IWL_DEFAULT_TX_RETRY  15

#define RX_QUEUE_SIZE                         256
#define RX_QUEUE_MASK                         255
#define RX_QUEUE_SIZE_LOG                     8

#define TFD_TX_CMD_SLOTS 256
#define TFD_CMD_SLOTS 32

#define TFD_MAX_PAYLOAD_SIZE (sizeof(struct iwl4965_cmd) - \
			      sizeof(struct iwl4965_cmd_meta))

/*
 * RX related structures and functions
 */
#define RX_FREE_BUFFERS 64
#define RX_LOW_WATERMARK 8

/* Size of one Rx buffer in host DRAM */
#define IWL_RX_BUF_SIZE_4K (4 * 1024)
#define IWL_RX_BUF_SIZE_8K (8 * 1024)

/* Sizes and addresses for instruction and data memory (SRAM) in
 * 4965's embedded processor.  Driver access is via HBUS_TARG_MEM_* regs. */
#define RTC_INST_LOWER_BOUND			(0x000000)
#define KDR_RTC_INST_UPPER_BOUND		(0x018000)

#define RTC_DATA_LOWER_BOUND			(0x800000)
#define KDR_RTC_DATA_UPPER_BOUND		(0x80A000)

#define KDR_RTC_INST_SIZE    (KDR_RTC_INST_UPPER_BOUND - RTC_INST_LOWER_BOUND)
#define KDR_RTC_DATA_SIZE    (KDR_RTC_DATA_UPPER_BOUND - RTC_DATA_LOWER_BOUND)

#define IWL_MAX_INST_SIZE KDR_RTC_INST_SIZE
#define IWL_MAX_DATA_SIZE KDR_RTC_DATA_SIZE

/* Size of uCode instruction memory in bootstrap state machine */
#define IWL_MAX_BSM_SIZE BSM_SRAM_SIZE

static inline int iwl4965_hw_valid_rtc_data_addr(u32 addr)
{
	return (addr >= RTC_DATA_LOWER_BOUND) &&
	       (addr < KDR_RTC_DATA_UPPER_BOUND);
}

/********************* START TEMPERATURE *************************************/

/**
 * 4965 temperature calculation.
 *
 * The driver must calculate the device temperature before calculating
 * a txpower setting (amplifier gain is temperature dependent).  The
 * calculation uses 4 measurements, 3 of which (R1, R2, R3) are calibration
 * values used for the life of the driver, and one of which (R4) is the
 * real-time temperature indicator.
 *
 * uCode provides all 4 values to the driver via the "initialize alive"
 * notification (see struct iwl4965_init_alive_resp).  After the runtime uCode
 * image loads, uCode updates the R4 value via statistics notifications
 * (see STATISTICS_NOTIFICATION), which occur after each received beacon
 * when associated, or can be requested via REPLY_STATISTICS_CMD.
 *
 * NOTE:  uCode provides the R4 value as a 23-bit signed value.  Driver
 *        must sign-extend to 32 bits before applying formula below.
 *
 * Formula:
 *
 * degrees Kelvin = ((97 * 259 * (R4 - R2) / (R3 - R1)) / 100) + 8
 *
 * NOTE:  The basic formula is 259 * (R4-R2) / (R3-R1).  The 97/100 is
 * an additional correction, which should be centered around 0 degrees
 * Celsius (273 degrees Kelvin).  The 8 (3 percent of 273) compensates for
 * centering the 97/100 correction around 0 degrees K.
 *
 * Add 273 to Kelvin value to find degrees Celsius, for comparing current
 * temperature with factory-measured temperatures when calculating txpower
 * settings.
 */
#define TEMPERATURE_CALIB_KELVIN_OFFSET 8
#define TEMPERATURE_CALIB_A_VAL 259

/* Limit range of calculated temperature to be between these Kelvin values */
#define IWL_TX_POWER_TEMPERATURE_MIN  (263)
#define IWL_TX_POWER_TEMPERATURE_MAX  (410)

#define IWL_TX_POWER_TEMPERATURE_OUT_OF_RANGE(t) \
	(((t) < IWL_TX_POWER_TEMPERATURE_MIN) || \
	 ((t) > IWL_TX_POWER_TEMPERATURE_MAX))

/********************* END TEMPERATURE ***************************************/

/********************* START TXPOWER *****************************************/

/**
 * 4965 txpower calculations rely on information from three sources:
 *
 *     1) EEPROM
 *     2) "initialize" alive notification
 *     3) statistics notifications
 *
 * EEPROM data consists of:
 *
 * 1)  Regulatory information (max txpower and channel usage flags) is provided
 *     separately for each channel that can possibly supported by 4965.
 *     40 MHz wide (.11n fat) channels are listed separately from 20 MHz
 *     (legacy) channels.
 *
 *     See struct iwl4965_eeprom_channel for format, and struct iwl4965_eeprom
 *     for locations in EEPROM.
 *
 * 2)  Factory txpower calibration information is provided separately for
 *     sub-bands of contiguous channels.  2.4GHz has just one sub-band,
 *     but 5 GHz has several sub-bands.
 *
 *     In addition, per-band (2.4 and 5 Ghz) saturation txpowers are provided.
 *
 *     See struct iwl4965_eeprom_calib_info (and the tree of structures
 *     contained within it) for format, and struct iwl4965_eeprom for
 *     locations in EEPROM.
 *
 * "Initialization alive" notification (see struct iwl4965_init_alive_resp)
 * consists of:
 *
 * 1)  Temperature calculation parameters.
 *
 * 2)  Power supply voltage measurement.
 *
 * 3)  Tx gain compensation to balance 2 transmitters for MIMO use.
 *
 * Statistics notifications deliver:
 *
 * 1)  Current values for temperature param R4.
 */

/**
 * To calculate a txpower setting for a given desired target txpower, channel,
 * modulation bit rate, and transmitter chain (4965 has 2 transmitters to
 * support MIMO and transmit diversity), driver must do the following:
 *
 * 1)  Compare desired txpower vs. (EEPROM) regulatory limit for this channel.
 *     Do not exceed regulatory limit; reduce target txpower if necessary.
 *
 *     If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31),
 *     2 transmitters will be used simultaneously; driver must reduce the
 *     regulatory limit by 3 dB (half-power) for each transmitter, so the
 *     combined total output of the 2 transmitters is within regulatory limits.
 *
 *
 * 2)  Compare target txpower vs. (EEPROM) saturation txpower *reduced by
 *     backoff for this bit rate*.  Do not exceed (saturation - backoff[rate]);
 *     reduce target txpower if necessary.
 *
 *     Backoff values below are in 1/2 dB units (equivalent to steps in
 *     txpower gain tables):
 *
 *     OFDM 6 - 36 MBit:  10 steps (5 dB)
 *     OFDM 48 MBit:      15 steps (7.5 dB)
 *     OFDM 54 MBit:      17 steps (8.5 dB)
 *     OFDM 60 MBit:      20 steps (10 dB)
 *     CCK all rates:     10 steps (5 dB)
 *
 *     Backoff values apply to saturation txpower on a per-transmitter basis;
 *     when using MIMO (2 transmitters), each transmitter uses the same
 *     saturation level provided in EEPROM, and the same backoff values;
 *     no reduction (such as with regulatory txpower limits) is required.
 *
 *     Saturation and Backoff values apply equally to 20 Mhz (legacy) channel
 *     widths and 40 Mhz (.11n fat) channel widths; there is no separate
 *     factory measurement for fat channels.
 *
 *     The result of this step is the final target txpower.  The rest of
 *     the steps figure out the proper settings for the device to achieve
 *     that target txpower.
 *
 *
 * 3)  Determine (EEPROM) calibration subband for the target channel, by
 *     comparing against first and last channels in each subband
 *     (see struct iwl4965_eeprom_calib_subband_info).
 *
 *
 * 4)  Linearly interpolate (EEPROM) factory calibration measurement sets,
 *     referencing the 2 factory-measured (sample) channels within the subband.
 *
 *     Interpolation is based on difference between target channel's frequency
 *     and the sample channels' frequencies.  Since channel numbers are based
 *     on frequency (5 MHz between each channel number), this is equivalent
 *     to interpolating based on channel number differences.
 *
 *     Note that the sample channels may or may not be the channels at the
 *     edges of the subband.  The target channel may be "outside" of the
 *     span of the sampled channels.
 *
 *     Driver may choose the pair (for 2 Tx chains) of measurements (see
 *     struct iwl4965_eeprom_calib_ch_info) for which the actual measured
 *     txpower comes closest to the desired txpower.  Usually, though,
 *     the middle set of measurements is closest to the regulatory limits,
 *     and is therefore a good choice for all txpower calculations (this
 *     assumes that high accuracy is needed for maximizing legal txpower,
 *     while lower txpower configurations do not need as much accuracy).
 *
 *     Driver should interpolate both members of the chosen measurement pair,
 *     i.e. for both Tx chains (radio transmitters), unless the driver knows
 *     that only one of the chains will be used (e.g. only one tx antenna
 *     connected, but this should be unusual).  The rate scaling algorithm
 *     switches antennas to find best performance, so both Tx chains will
 *     be used (although only one at a time) even for non-MIMO transmissions.
 *
 *     Driver should interpolate factory values for temperature, gain table
 *     index, and actual power.  The power amplifier detector values are
 *     not used by the driver.
 *
 *     Sanity check:  If the target channel happens to be one of the sample
 *     channels, the results should agree with the sample channel's
 *     measurements!
 *
 *
 * 5)  Find difference between desired txpower and (interpolated)
 *     factory-measured txpower.  Using (interpolated) factory gain table index
 *     (shown elsewhere) as a starting point, adjust this index lower to
 *     increase txpower, or higher to decrease txpower, until the target
 *     txpower is reached.  Each step in the gain table is 1/2 dB.
 *
 *     For example, if factory measured txpower is 16 dBm, and target txpower
 *     is 13 dBm, add 6 steps to the factory gain index to reduce txpower
 *     by 3 dB.
 *
 *
 * 6)  Find difference between current device temperature and (interpolated)
 *     factory-measured temperature for sub-band.  Factory values are in
 *     degrees Celsius.  To calculate current temperature, see comments for
 *     "4965 temperature calculation".
 *
 *     If current temperature is higher than factory temperature, driver must
 *     increase gain (lower gain table index), and vice versa.
 *
 *     Temperature affects gain differently for different channels:
 *
 *     2.4 GHz all channels:  3.5 degrees per half-dB step
 *     5 GHz channels 34-43:  4.5 degrees per half-dB step
 *     5 GHz channels >= 44:  4.0 degrees per half-dB step
 *
 *     NOTE:  Temperature can increase rapidly when transmitting, especially
 *            with heavy traffic at high txpowers.  Driver should update
 *            temperature calculations often under these conditions to
 *            maintain strong txpower in the face of rising temperature.
 *
 *
 * 7)  Find difference between current power supply voltage indicator
 *     (from "initialize alive") and factory-measured power supply voltage
 *     indicator (EEPROM).
 *
 *     If the current voltage is higher (indicator is lower) than factory
 *     voltage, gain should be reduced (gain table index increased) by:
 *
 *     (eeprom - current) / 7
 *
 *     If the current voltage is lower (indicator is higher) than factory
 *     voltage, gain should be increased (gain table index decreased) by:
 *
 *     2 * (current - eeprom) / 7
 *
 *     If number of index steps in either direction turns out to be > 2,
 *     something is wrong ... just use 0.
 *
 *     NOTE:  Voltage compensation is independent of band/channel.
 *
 *     NOTE:  "Initialize" uCode measures current voltage, which is assumed
 *            to be constant after this initial measurement.  Voltage
 *            compensation for txpower (number of steps in gain table)
 *            may be calculated once and used until the next uCode bootload.
 *
 *
 * 8)  If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31),
 *     adjust txpower for each transmitter chain, so txpower is balanced
 *     between the two chains.  There are 5 pairs of tx_atten[group][chain]
 *     values in "initialize alive", one pair for each of 5 channel ranges:
 *
 *     Group 0:  5 GHz channel 34-43
 *     Group 1:  5 GHz channel 44-70
 *     Group 2:  5 GHz channel 71-124
 *     Group 3:  5 GHz channel 125-200
 *     Group 4:  2.4 GHz all channels
 *
 *     Add the tx_atten[group][chain] value to the index for the target chain.
 *     The values are signed, but are in pairs of 0 and a non-negative number,
 *     so as to reduce gain (if necessary) of the "hotter" channel.  This
 *     avoids any need to double-check for regulatory compliance after
 *     this step.
 *
 *
 * 9)  If setting up for a CCK rate, lower the gain by adding a CCK compensation
 *     value to the index:
 *
 *     Hardware rev B:  9 steps (4.5 dB)
 *     Hardware rev C:  5 steps (2.5 dB)
 *
 *     Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG,
 *     bits [3:2], 1 = B, 2 = C.
 *
 *     NOTE:  This compensation is in addition to any saturation backoff that
 *            might have been applied in an earlier step.
 *
 *
 * 10) Select the gain table, based on band (2.4 vs 5 GHz).
 *
 *     Limit the adjusted index to stay within the table!
 *
 *
 * 11) Read gain table entries for DSP and radio gain, place into appropriate
 *     location(s) in command (struct iwl4965_txpowertable_cmd).
 */

/* Limit range of txpower output target to be between these values */
#define IWL_TX_POWER_TARGET_POWER_MIN       (0)	/* 0 dBm = 1 milliwatt */
#define IWL_TX_POWER_TARGET_POWER_MAX      (16)	/* 16 dBm */

/**
 * When MIMO is used (2 transmitters operating simultaneously), driver should
 * limit each transmitter to deliver a max of 3 dB below the regulatory limit
 * for the device.  That is, use half power for each transmitter, so total
 * txpower is within regulatory limits.
 *
 * The value "6" represents number of steps in gain table to reduce power 3 dB.
 * Each step is 1/2 dB.
 */
#define IWL_TX_POWER_MIMO_REGULATORY_COMPENSATION (6)

/**
 * CCK gain compensation.
 *
 * When calculating txpowers for CCK, after making sure that the target power
 * is within regulatory and saturation limits, driver must additionally
 * back off gain by adding these values to the gain table index.
 *
 * Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG,
 * bits [3:2], 1 = B, 2 = C.
 */
#define IWL_TX_POWER_CCK_COMPENSATION_B_STEP (9)
#define IWL_TX_POWER_CCK_COMPENSATION_C_STEP (5)

/*
 * 4965 power supply voltage compensation for txpower
 */
#define TX_POWER_IWL_VOLTAGE_CODES_PER_03V   (7)

/**
 * Gain tables.
 *
 * The following tables contain pair of values for setting txpower, i.e.
 * gain settings for the output of the device's digital signal processor (DSP),
 * and for the analog gain structure of the transmitter.
 *
 * Each entry in the gain tables represents a step of 1/2 dB.  Note that these
 * are *relative* steps, not indications of absolute output power.  Output
 * power varies with temperature, voltage, and channel frequency, and also
 * requires consideration of average power (to satisfy regulatory constraints),
 * and peak power (to avoid distortion of the output signal).
 *
 * Each entry contains two values:
 * 1)  DSP gain (or sometimes called DSP attenuation).  This is a fine-grained
 *     linear value that multiplies the output of the digital signal processor,
 *     before being sent to the analog radio.
 * 2)  Radio gain.  This sets the analog gain of the radio Tx path.
 *     It is a coarser setting, and behaves in a logarithmic (dB) fashion.
 *
 * EEPROM contains factory calibration data for txpower.  This maps actual
 * measured txpower levels to gain settings in the "well known" tables
 * below ("well-known" means here that both factory calibration *and* the
 * driver work with the same table).
 *
 * There are separate tables for 2.4 GHz and 5 GHz bands.  The 5 GHz table
 * has an extension (into negative indexes), in case the driver needs to
 * boost power setting for high device temperatures (higher than would be
 * present during factory calibration).  A 5 Ghz EEPROM index of "40"
 * corresponds to the 49th entry in the table used by the driver.
 */
#define MIN_TX_GAIN_INDEX		(0)  /* highest gain, lowest idx, 2.4 */
#define MIN_TX_GAIN_INDEX_52GHZ_EXT	(-9) /* highest gain, lowest idx, 5 */

/**
 * 2.4 GHz gain table
 *
 * Index    Dsp gain   Radio gain
 *   0        110         0x3f      (highest gain)
 *   1        104         0x3f
 *   2         98         0x3f
 *   3        110         0x3e
 *   4        104         0x3e
 *   5         98         0x3e
 *   6        110         0x3d
 *   7        104         0x3d
 *   8         98         0x3d
 *   9        110         0x3c
 *  10        104         0x3c
 *  11         98         0x3c
 *  12        110         0x3b
 *  13        104         0x3b
 *  14         98         0x3b
 *  15        110         0x3a
 *  16        104         0x3a
 *  17         98         0x3a
 *  18        110         0x39
 *  19        104         0x39
 *  20         98         0x39
 *  21        110         0x38
 *  22        104         0x38
 *  23         98         0x38
 *  24        110         0x37
 *  25        104         0x37
 *  26         98         0x37
 *  27        110         0x36
 *  28        104         0x36
 *  29         98         0x36
 *  30        110         0x35
 *  31        104         0x35
 *  32         98         0x35
 *  33        110         0x34
 *  34        104         0x34
 *  35         98         0x34
 *  36        110         0x33
 *  37        104         0x33
 *  38         98         0x33
 *  39        110         0x32
 *  40        104         0x32
 *  41         98         0x32
 *  42        110         0x31
 *  43        104         0x31
 *  44         98         0x31
 *  45        110         0x30
 *  46        104         0x30
 *  47         98         0x30
 *  48        110          0x6
 *  49        104          0x6
 *  50         98          0x6
 *  51        110          0x5
 *  52        104          0x5
 *  53         98          0x5
 *  54        110          0x4
 *  55        104          0x4
 *  56         98          0x4
 *  57        110          0x3
 *  58        104          0x3
 *  59         98          0x3
 *  60        110          0x2
 *  61        104          0x2
 *  62         98          0x2
 *  63        110          0x1
 *  64        104          0x1
 *  65         98          0x1
 *  66        110          0x0
 *  67        104          0x0
 *  68         98          0x0
 *  69         97            0
 *  70         96            0
 *  71         95            0
 *  72         94            0
 *  73         93            0
 *  74         92            0
 *  75         91            0
 *  76         90            0
 *  77         89            0
 *  78         88            0
 *  79         87            0
 *  80         86            0
 *  81         85            0
 *  82         84            0
 *  83         83            0
 *  84         82            0
 *  85         81            0
 *  86         80            0
 *  87         79            0
 *  88         78            0
 *  89         77            0
 *  90         76            0
 *  91         75            0
 *  92         74            0
 *  93         73            0
 *  94         72            0
 *  95         71            0
 *  96         70            0
 *  97         69            0
 *  98         68            0
 */

/**
 * 5 GHz gain table
 *
 * Index    Dsp gain   Radio gain
 *  -9 	      123         0x3F      (highest gain)
 *  -8 	      117         0x3F
 *  -7        110         0x3F
 *  -6        104         0x3F
 *  -5         98         0x3F
 *  -4        110         0x3E
 *  -3        104         0x3E
 *  -2         98         0x3E
 *  -1        110         0x3D
 *   0        104         0x3D
 *   1         98         0x3D
 *   2        110         0x3C
 *   3        104         0x3C
 *   4         98         0x3C
 *   5        110         0x3B
 *   6        104         0x3B
 *   7         98         0x3B
 *   8        110         0x3A
 *   9        104         0x3A
 *  10         98         0x3A
 *  11        110         0x39
 *  12        104         0x39
 *  13         98         0x39
 *  14        110         0x38
 *  15        104         0x38
 *  16         98         0x38
 *  17        110         0x37
 *  18        104         0x37
 *  19         98         0x37
 *  20        110         0x36
 *  21        104         0x36
 *  22         98         0x36
 *  23        110         0x35
 *  24        104         0x35
 *  25         98         0x35
 *  26        110         0x34
 *  27        104         0x34
 *  28         98         0x34
 *  29        110         0x33
 *  30        104         0x33
 *  31         98         0x33
 *  32        110         0x32
 *  33        104         0x32
 *  34         98         0x32
 *  35        110         0x31
 *  36        104         0x31
 *  37         98         0x31
 *  38        110         0x30
 *  39        104         0x30
 *  40         98         0x30
 *  41        110         0x25
 *  42        104         0x25
 *  43         98         0x25
 *  44        110         0x24
 *  45        104         0x24
 *  46         98         0x24
 *  47        110         0x23
 *  48        104         0x23
 *  49         98         0x23
 *  50        110         0x22
 *  51        104         0x18
 *  52         98         0x18
 *  53        110         0x17
 *  54        104         0x17
 *  55         98         0x17
 *  56        110         0x16
 *  57        104         0x16
 *  58         98         0x16
 *  59        110         0x15
 *  60        104         0x15
 *  61         98         0x15
 *  62        110         0x14
 *  63        104         0x14
 *  64         98         0x14
 *  65        110         0x13
 *  66        104         0x13
 *  67         98         0x13
 *  68        110         0x12
 *  69        104         0x08
 *  70         98         0x08
 *  71        110         0x07
 *  72        104         0x07
 *  73         98         0x07
 *  74        110         0x06
 *  75        104         0x06
 *  76         98         0x06
 *  77        110         0x05
 *  78        104         0x05
 *  79         98         0x05
 *  80        110         0x04
 *  81        104         0x04
 *  82         98         0x04
 *  83        110         0x03
 *  84        104         0x03
 *  85         98         0x03
 *  86        110         0x02
 *  87        104         0x02
 *  88         98         0x02
 *  89        110         0x01
 *  90        104         0x01
 *  91         98         0x01
 *  92        110         0x00
 *  93        104         0x00
 *  94         98         0x00
 *  95         93         0x00
 *  96         88         0x00
 *  97         83         0x00
 *  98         78         0x00
 */


/**
 * Sanity checks and default values for EEPROM regulatory levels.
 * If EEPROM values fall outside MIN/MAX range, use default values.
 *
 * Regulatory limits refer to the maximum average txpower allowed by
 * regulatory agencies in the geographies in which the device is meant
 * to be operated.  These limits are SKU-specific (i.e. geography-specific),
 * and channel-specific; each channel has an individual regulatory limit
 * listed in the EEPROM.
 *
 * Units are in half-dBm (i.e. "34" means 17 dBm).
 */
#define IWL_TX_POWER_DEFAULT_REGULATORY_24   (34)
#define IWL_TX_POWER_DEFAULT_REGULATORY_52   (34)
#define IWL_TX_POWER_REGULATORY_MIN          (0)
#define IWL_TX_POWER_REGULATORY_MAX          (34)

/**
 * Sanity checks and default values for EEPROM saturation levels.
 * If EEPROM values fall outside MIN/MAX range, use default values.
 *
 * Saturation is the highest level that the output power amplifier can produce
 * without significant clipping distortion.  This is a "peak" power level.
 * Different types of modulation (i.e. various "rates", and OFDM vs. CCK)
 * require differing amounts of backoff, relative to their average power output,
 * in order to avoid clipping distortion.
 *
 * Driver must make sure that it is violating neither the saturation limit,
 * nor the regulatory limit, when calculating Tx power settings for various
 * rates.
 *
 * Units are in half-dBm (i.e. "38" means 19 dBm).
 */
#define IWL_TX_POWER_DEFAULT_SATURATION_24   (38)
#define IWL_TX_POWER_DEFAULT_SATURATION_52   (38)
#define IWL_TX_POWER_SATURATION_MIN          (20)
#define IWL_TX_POWER_SATURATION_MAX          (50)

/**
 * Channel groups used for Tx Attenuation calibration (MIMO tx channel balance)
 * and thermal Txpower calibration.
 *
 * When calculating txpower, driver must compensate for current device
 * temperature; higher temperature requires higher gain.  Driver must calculate
 * current temperature (see "4965 temperature calculation"), then compare vs.
 * factory calibration temperature in EEPROM; if current temperature is higher
 * than factory temperature, driver must *increase* gain by proportions shown
 * in table below.  If current temperature is lower than factory, driver must
 * *decrease* gain.
 *
 * Different frequency ranges require different compensation, as shown below.
 */
/* Group 0, 5.2 GHz ch 34-43:  4.5 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR1_FCH 34
#define CALIB_IWL_TX_ATTEN_GR1_LCH 43

/* Group 1, 5.3 GHz ch 44-70:  4.0 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR2_FCH 44
#define CALIB_IWL_TX_ATTEN_GR2_LCH 70

/* Group 2, 5.5 GHz ch 71-124:  4.0 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR3_FCH 71
#define CALIB_IWL_TX_ATTEN_GR3_LCH 124

/* Group 3, 5.7 GHz ch 125-200:  4.0 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR4_FCH 125
#define CALIB_IWL_TX_ATTEN_GR4_LCH 200

/* Group 4, 2.4 GHz all channels:  3.5 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR5_FCH 1
#define CALIB_IWL_TX_ATTEN_GR5_LCH 20

enum {
	CALIB_CH_GROUP_1 = 0,
	CALIB_CH_GROUP_2 = 1,
	CALIB_CH_GROUP_3 = 2,
	CALIB_CH_GROUP_4 = 3,
	CALIB_CH_GROUP_5 = 4,
	CALIB_CH_GROUP_MAX
};

/********************* END TXPOWER *****************************************/

/****************************/
/* Flow Handler Definitions */
/****************************/

/**
 * This I/O area is directly read/writable by driver (e.g. Linux uses writel())
 * Addresses are offsets from device's PCI hardware base address.
 */
#define FH_MEM_LOWER_BOUND                   (0x1000)
#define FH_MEM_UPPER_BOUND                   (0x1EF0)

/**
 * Keep-Warm (KW) buffer base address.
 *
 * Driver must allocate a 4KByte buffer that is used by 4965 for keeping the
 * host DRAM powered on (via dummy accesses to DRAM) to maintain low-latency
 * DRAM access when 4965 is Txing or Rxing.  The dummy accesses prevent host
 * from going into a power-savings mode that would cause higher DRAM latency,
 * and possible data over/under-runs, before all Tx/Rx is complete.
 *
 * Driver loads IWL_FH_KW_MEM_ADDR_REG with the physical address (bits 35:4)
 * of the buffer, which must be 4K aligned.  Once this is set up, the 4965
 * automatically invokes keep-warm accesses when normal accesses might not
 * be sufficient to maintain fast DRAM response.
 *
 * Bit fields:
 *  31-0:  Keep-warm buffer physical base address [35:4], must be 4K aligned
 */
#define IWL_FH_KW_MEM_ADDR_REG		     (FH_MEM_LOWER_BOUND + 0x97C)


/**
 * TFD Circular Buffers Base (CBBC) addresses
 *
 * 4965 has 16 base pointer registers, one for each of 16 host-DRAM-resident
 * circular buffers (CBs/queues) containing Transmit Frame Descriptors (TFDs)
 * (see struct iwl_tfd_frame).  These 16 pointer registers are offset by 0x04
 * bytes from one another.  Each TFD circular buffer in DRAM must be 256-byte
 * aligned (address bits 0-7 must be 0).
 *
 * Bit fields in each pointer register:
 *  27-0: TFD CB physical base address [35:8], must be 256-byte aligned
 */
#define FH_MEM_CBBC_LOWER_BOUND              (FH_MEM_LOWER_BOUND + 0x9D0)
#define FH_MEM_CBBC_UPPER_BOUND              (FH_MEM_LOWER_BOUND + 0xA10)

/* Find TFD CB base pointer for given queue (range 0-15). */
#define FH_MEM_CBBC_QUEUE(x)  (FH_MEM_CBBC_LOWER_BOUND + (x) * 0x4)


/**
 * Rx SRAM Control and Status Registers (RSCSR)
 *
 * These registers provide handshake between driver and 4965 for the Rx queue
 * (this queue handles *all* command responses, notifications, Rx data, etc.
 * sent from 4965 uCode to host driver).  Unlike Tx, there is only one Rx
 * queue, and only one Rx DMA/FIFO channel.  Also unlike Tx, which can
 * concatenate up to 20 DRAM buffers to form a Tx frame, each Receive Buffer
 * Descriptor (RBD) points to only one Rx Buffer (RB); there is a 1:1
 * mapping between RBDs and RBs.
 *
 * Driver must allocate host DRAM memory for the following, and set the
 * physical address of each into 4965 registers:
 *
 * 1)  Receive Buffer Descriptor (RBD) circular buffer (CB), typically with 256
 *     entries (although any power of 2, up to 4096, is selectable by driver).
 *     Each entry (1 dword) points to a receive buffer (RB) of consistent size
 *     (typically 4K, although 8K or 16K are also selectable by driver).
 *     Driver sets up RB size and number of RBDs in the CB via Rx config
 *     register FH_MEM_RCSR_CHNL0_CONFIG_REG.
 *
 *     Bit fields within one RBD:
 *     27-0:  Receive Buffer physical address bits [35:8], 256-byte aligned
 *
 *     Driver sets physical address [35:8] of base of RBD circular buffer
 *     into FH_RSCSR_CHNL0_RBDCB_BASE_REG [27:0].
 *
 * 2)  Rx status buffer, 8 bytes, in which 4965 indicates which Rx Buffers
 *     (RBs) have been filled, via a "write pointer", actually the index of
 *     the RB's corresponding RBD within the circular buffer.  Driver sets
 *     physical address [35:4] into FH_RSCSR_CHNL0_STTS_WPTR_REG [31:0].
 *
 *     Bit fields in lower dword of Rx status buffer (upper dword not used
 *     by driver; see struct iwl4965_shared, val0):
 *     31-12:  Not used by driver
 *     11- 0:  Index of last filled Rx buffer descriptor
 *             (4965 writes, driver reads this value)
 *
 * As the driver prepares Receive Buffers (RBs) for 4965 to fill, driver must
 * enter pointers to these RBs into contiguous RBD circular buffer entries,
 * and update the 4965's "write" index register, FH_RSCSR_CHNL0_RBDCB_WPTR_REG.
 *
 * This "write" index corresponds to the *next* RBD that the driver will make
 * available, i.e. one RBD past the tail of the ready-to-fill RBDs within
 * the circular buffer.  This value should initially be 0 (before preparing any
 * RBs), should be 8 after preparing the first 8 RBs (for example), and must
 * wrap back to 0 at the end of the circular buffer (but don't wrap before
 * "read" index has advanced past 1!  See below).
 * NOTE:  4965 EXPECTS THE WRITE INDEX TO BE INCREMENTED IN MULTIPLES OF 8.
 *
 * As the 4965 fills RBs (referenced from contiguous RBDs within the circular
 * buffer), it updates the Rx status buffer in host DRAM, 2) described above,
 * to tell the driver the index of the latest filled RBD.  The driver must
 * read this "read" index from DRAM after receiving an Rx interrupt from 4965.
 *
 * The driver must also internally keep track of a third index, which is the
 * next RBD to process.  When receiving an Rx interrupt, driver should process
 * all filled but unprocessed RBs up to, but not including, the RB
 * corresponding to the "read" index.  For example, if "read" index becomes "1",
 * driver may process the RB pointed to by RBD 0.  Depending on volume of
 * traffic, there may be many RBs to process.
 *
 * If read index == write index, 4965 thinks there is no room to put new data.
 * Due to this, the maximum number of filled RBs is 255, instead of 256.  To
 * be safe, make sure that there is a gap of at least 2 RBDs between "write"
 * and "read" indexes; that is, make sure that there are no more than 254
 * buffers waiting to be filled.
 */
#define FH_MEM_RSCSR_LOWER_BOUND	(FH_MEM_LOWER_BOUND + 0xBC0)
#define FH_MEM_RSCSR_UPPER_BOUND	(FH_MEM_LOWER_BOUND + 0xC00)
#define FH_MEM_RSCSR_CHNL0		(FH_MEM_RSCSR_LOWER_BOUND)

/**
 * Physical base address of 8-byte Rx Status buffer.
 * Bit fields:
 *  31-0: Rx status buffer physical base address [35:4], must 16-byte aligned.
 */
#define FH_RSCSR_CHNL0_STTS_WPTR_REG		(FH_MEM_RSCSR_CHNL0)

/**
 * Physical base address of Rx Buffer Descriptor Circular Buffer.
 * Bit fields:
 *  27-0:  RBD CD physical base address [35:8], must be 256-byte aligned.
 */
#define FH_RSCSR_CHNL0_RBDCB_BASE_REG		(FH_MEM_RSCSR_CHNL0 + 0x004)

/**
 * Rx write pointer (index, really!).
 * Bit fields:
 *  11-0:  Index of driver's most recent prepared-to-be-filled RBD, + 1.
 *         NOTE:  For 256-entry circular buffer, use only bits [7:0].
 */
#define FH_RSCSR_CHNL0_RBDCB_WPTR_REG		(FH_MEM_RSCSR_CHNL0 + 0x008)
#define FH_RSCSR_CHNL0_WPTR        (FH_RSCSR_CHNL0_RBDCB_WPTR_REG)


/**
 * Rx Config/Status Registers (RCSR)
 * Rx Config Reg for channel 0 (only channel used)
 *
 * Driver must initialize FH_MEM_RCSR_CHNL0_CONFIG_REG as follows for
 * normal operation (see bit fields).
 *
 * Clearing FH_MEM_RCSR_CHNL0_CONFIG_REG to 0 turns off Rx DMA.
 * Driver should poll FH_MEM_RSSR_RX_STATUS_REG	for
 * FH_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (bit 24) before continuing.
 *
 * Bit fields:
 * 31-30: Rx DMA channel enable: '00' off/pause, '01' pause at end of frame,
 *        '10' operate normally
 * 29-24: reserved
 * 23-20: # RBDs in circular buffer = 2^value; use "8" for 256 RBDs (normal),
 *        min "5" for 32 RBDs, max "12" for 4096 RBDs.
 * 19-18: reserved
 * 17-16: size of each receive buffer; '00' 4K (normal), '01' 8K,
 *        '10' 12K, '11' 16K.
 * 15-14: reserved
 * 13-12: IRQ destination; '00' none, '01' host driver (normal operation)
 * 11- 4: timeout for closing Rx buffer and interrupting host (units 32 usec)
 *        typical value 0x10 (about 1/2 msec)
 *  3- 0: reserved
 */
#define FH_MEM_RCSR_LOWER_BOUND      (FH_MEM_LOWER_BOUND + 0xC00)
#define FH_MEM_RCSR_UPPER_BOUND      (FH_MEM_LOWER_BOUND + 0xCC0)
#define FH_MEM_RCSR_CHNL0            (FH_MEM_RCSR_LOWER_BOUND)

#define FH_MEM_RCSR_CHNL0_CONFIG_REG	(FH_MEM_RCSR_CHNL0)

#define FH_RCSR_CHNL0_RX_CONFIG_RB_TIMEOUT_MASK   (0x00000FF0) /* bit 4-11 */
#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_MASK     (0x00001000) /* bit 12 */
#define FH_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME_MASK (0x00008000) /* bit 15 */
#define FH_RCSR_CHNL0_RX_CONFIG_RB_SIZE_MASK	  (0x00030000) /* bits 16-17 */
#define FH_RCSR_CHNL0_RX_CONFIG_RBDBC_SIZE_MASK   (0x00F00000) /* bits 20-23 */
#define FH_RCSR_CHNL0_RX_CONFIG_DMA_CHNL_EN_MASK  (0xC0000000) /* bits 30-31 */

#define FH_RCSR_RX_CONFIG_RBDCB_SIZE_BITSHIFT	(20)
#define FH_RCSR_RX_CONFIG_REG_IRQ_RBTH_BITSHIFT	(4)
#define RX_RB_TIMEOUT	(0x10)

#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_VAL         (0x00000000)
#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_EOF_VAL     (0x40000000)
#define FH_RCSR_RX_CONFIG_CHNL_EN_ENABLE_VAL        (0x80000000)

#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K    (0x00000000)
#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_8K    (0x00010000)
#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_12K   (0x00020000)
#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_16K   (0x00030000)

#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_NO_INT_VAL       (0x00000000)
#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_INT_HOST_VAL     (0x00001000)


/**
 * Rx Shared Status Registers (RSSR)
 *
 * After stopping Rx DMA channel (writing 0 to FH_MEM_RCSR_CHNL0_CONFIG_REG),
 * driver must poll FH_MEM_RSSR_RX_STATUS_REG until Rx channel is idle.
 *
 * Bit fields:
 *  24:  1 = Channel 0 is idle
 *
 * FH_MEM_RSSR_SHARED_CTRL_REG and FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV contain
 * default values that should not be altered by the driver.
 */
#define FH_MEM_RSSR_LOWER_BOUND                	(FH_MEM_LOWER_BOUND + 0xC40)
#define FH_MEM_RSSR_UPPER_BOUND               	(FH_MEM_LOWER_BOUND + 0xD00)

#define FH_MEM_RSSR_SHARED_CTRL_REG           	(FH_MEM_RSSR_LOWER_BOUND)
#define FH_MEM_RSSR_RX_STATUS_REG	(FH_MEM_RSSR_LOWER_BOUND + 0x004)
#define FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV  (FH_MEM_RSSR_LOWER_BOUND + 0x008)

#define FH_RSSR_CHNL0_RX_STATUS_CHNL_IDLE	(0x01000000)


/**
 * Transmit DMA Channel Control/Status Registers (TCSR)
 *
 * 4965 has one configuration register for each of 8 Tx DMA/FIFO channels
 * supported in hardware (don't confuse these with the 16 Tx queues in DRAM,
 * which feed the DMA/FIFO channels); config regs are separated by 0x20 bytes.
 *
 * To use a Tx DMA channel, driver must initialize its
 * IWL_FH_TCSR_CHNL_TX_CONFIG_REG(chnl) with:
 *
 * IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE |
 * IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL
 *
 * All other bits should be 0.
 *
 * Bit fields:
 * 31-30: Tx DMA channel enable: '00' off/pause, '01' pause at end of frame,
 *        '10' operate normally
 * 29- 4: Reserved, set to "0"
 *     3: Enable internal DMA requests (1, normal operation), disable (0)
 *  2- 0: Reserved, set to "0"
 */
#define IWL_FH_TCSR_LOWER_BOUND  (FH_MEM_LOWER_BOUND + 0xD00)
#define IWL_FH_TCSR_UPPER_BOUND  (FH_MEM_LOWER_BOUND + 0xE60)

/* Find Control/Status reg for given Tx DMA/FIFO channel */
#define IWL_FH_TCSR_CHNL_TX_CONFIG_REG(_chnl) \
	(IWL_FH_TCSR_LOWER_BOUND + 0x20 * _chnl)

#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_DISABLE_VAL    (0x00000000)
#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL     (0x00000008)

#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE            (0x00000000)
#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE_EOF        (0x40000000)
#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE           (0x80000000)

/**
 * Tx Shared Status Registers (TSSR)
 *
 * After stopping Tx DMA channel (writing 0 to
 * IWL_FH_TCSR_CHNL_TX_CONFIG_REG(chnl)), driver must poll
 * IWL_FH_TSSR_TX_STATUS_REG until selected Tx channel is idle
 * (channel's buffers empty | no pending requests).
 *
 * Bit fields:
 * 31-24:  1 = Channel buffers empty (channel 7:0)
 * 23-16:  1 = No pending requests (channel 7:0)
 */
#define IWL_FH_TSSR_LOWER_BOUND		(FH_MEM_LOWER_BOUND + 0xEA0)
#define IWL_FH_TSSR_UPPER_BOUND		(FH_MEM_LOWER_BOUND + 0xEC0)

#define IWL_FH_TSSR_TX_STATUS_REG	(IWL_FH_TSSR_LOWER_BOUND + 0x010)

#define IWL_FH_TSSR_TX_STATUS_REG_BIT_BUFS_EMPTY(_chnl)	\
	((1 << (_chnl)) << 24)
#define IWL_FH_TSSR_TX_STATUS_REG_BIT_NO_PEND_REQ(_chnl) \
	((1 << (_chnl)) << 16)

#define IWL_FH_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE(_chnl) \
	(IWL_FH_TSSR_TX_STATUS_REG_BIT_BUFS_EMPTY(_chnl) | \
	IWL_FH_TSSR_TX_STATUS_REG_BIT_NO_PEND_REQ(_chnl))


/********************* START TX SCHEDULER *************************************/

/**
 * 4965 Tx Scheduler
 *
 * The Tx Scheduler selects the next frame to be transmitted, chosing TFDs
 * (Transmit Frame Descriptors) from up to 16 circular Tx queues resident in
 * host DRAM.  It steers each frame's Tx command (which contains the frame
 * data) into one of up to 7 prioritized Tx DMA FIFO channels within the
 * device.  A queue maps to only one (selectable by driver) Tx DMA channel,
 * but one DMA channel may take input from several queues.
 *
 * Tx DMA channels have dedicated purposes.  For 4965, they are used as follows:
 *
 * 0 -- EDCA BK (background) frames, lowest priority
 * 1 -- EDCA BE (best effort) frames, normal priority
 * 2 -- EDCA VI (video) frames, higher priority
 * 3 -- EDCA VO (voice) and management frames, highest priority
 * 4 -- Commands (e.g. RXON, etc.)
 * 5 -- HCCA short frames
 * 6 -- HCCA long frames
 * 7 -- not used by driver (device-internal only)
 *
 * Driver should normally map queues 0-6 to Tx DMA/FIFO channels 0-6.
 * In addition, driver can map queues 7-15 to Tx DMA/FIFO channels 0-3 to
 * support 11n aggregation via EDCA DMA channels.
 *
 * The driver sets up each queue to work in one of two modes:
 *
 * 1)  Scheduler-Ack, in which the scheduler automatically supports a
 *     block-ack (BA) window of up to 64 TFDs.  In this mode, each queue
 *     contains TFDs for a unique combination of Recipient Address (RA)
 *     and Traffic Identifier (TID), that is, traffic of a given
 *     Quality-Of-Service (QOS) priority, destined for a single station.
 *
 *     In scheduler-ack mode, the scheduler keeps track of the Tx status of
 *     each frame within the BA window, including whether it's been transmitted,
 *     and whether it's been acknowledged by the receiving station.  The device
 *     automatically processes block-acks received from the receiving STA,
 *     and reschedules un-acked frames to be retransmitted (successful
 *     Tx completion may end up being out-of-order).
 *
 *     The driver must maintain the queue's Byte Count table in host DRAM
 *     (struct iwl4965_sched_queue_byte_cnt_tbl) for this mode.
 *     This mode does not support fragmentation.
 *
 * 2)  FIFO (a.k.a. non-Scheduler-ACK), in which each TFD is processed in order.
 *     The device may automatically retry Tx, but will retry only one frame
 *     at a time, until receiving ACK from receiving station, or reaching
 *     retry limit and giving up.
 *
 *     The command queue (#4) must use this mode!
 *     This mode does not require use of the Byte Count table in host DRAM.
 *
 * Driver controls scheduler operation via 3 means:
 * 1)  Scheduler registers
 * 2)  Shared scheduler data base in internal 4956 SRAM
 * 3)  Shared data in host DRAM
 *
 * Initialization:
 *
 * When loading, driver should allocate memory for:
 * 1)  16 TFD circular buffers, each with space for (typically) 256 TFDs.
 * 2)  16 Byte Count circular buffers in 16 KBytes contiguous memory
 *     (1024 bytes for each queue).
 *
 * After receiving "Alive" response from uCode, driver must initialize
 * the scheduler (especially for queue #4, the command queue, otherwise
 * the driver can't issue commands!):
 */

/**
 * Max Tx window size is the max number of contiguous TFDs that the scheduler
 * can keep track of at one time when creating block-ack chains of frames.
 * Note that "64" matches the number of ack bits in a block-ack packet.
 * Driver should use SCD_WIN_SIZE and SCD_FRAME_LIMIT values to initialize
 * SCD_CONTEXT_QUEUE_OFFSET(x) values.
 */
#define SCD_WIN_SIZE				64
#define SCD_FRAME_LIMIT				64

/* SCD registers are internal, must be accessed via HBUS_TARG_PRPH regs */
#define SCD_START_OFFSET		0xa02c00

/*
 * 4965 tells driver SRAM address for internal scheduler structs via this reg.
 * Value is valid only after "Alive" response from uCode.
 */
#define SCD_SRAM_BASE_ADDR           (SCD_START_OFFSET + 0x0)

/*
 * Driver may need to update queue-empty bits after changing queue's
 * write and read pointers (indexes) during (re-)initialization (i.e. when
 * scheduler is not tracking what's happening).
 * Bit fields:
 * 31-16:  Write mask -- 1: update empty bit, 0: don't change empty bit
 * 15-00:  Empty state, one for each queue -- 1: empty, 0: non-empty
 * NOTE:  This register is not used by Linux driver.
 */
#define SCD_EMPTY_BITS               (SCD_START_OFFSET + 0x4)

/*
 * Physical base address of array of byte count (BC) circular buffers (CBs).
 * Each Tx queue has a BC CB in host DRAM to support Scheduler-ACK mode.
 * This register points to BC CB for queue 0, must be on 1024-byte boundary.
 * Others are spaced by 1024 bytes.
 * Each BC CB is 2 bytes * (256 + 64) = 740 bytes, followed by 384 bytes pad.
 * (Index into a queue's BC CB) = (index into queue's TFD CB) = (SSN & 0xff).
 * Bit fields:
 * 25-00:  Byte Count CB physical address [35:10], must be 1024-byte aligned.
 */
#define SCD_DRAM_BASE_ADDR           (SCD_START_OFFSET + 0x10)

/*
 * Enables any/all Tx DMA/FIFO channels.
 * Scheduler generates requests for only the active channels.
 * Set this to 0xff to enable all 8 channels (normal usage).
 * Bit fields:
 *  7- 0:  Enable (1), disable (0), one bit for each channel 0-7
 */
#define SCD_TXFACT                   (SCD_START_OFFSET + 0x1c)

/* Mask to enable contiguous Tx DMA/FIFO channels between "lo" and "hi". */
#define SCD_TXFACT_REG_TXFIFO_MASK(lo, hi) \
       ((1 << (hi)) | ((1 << (hi)) - (1 << (lo))))

/*
 * Queue (x) Write Pointers (indexes, really!), one for each Tx queue.
 * Initialized and updated by driver as new TFDs are added to queue.
 * NOTE:  If using Block Ack, index must correspond to frame's
 *        Start Sequence Number; index = (SSN & 0xff)
 * NOTE:  Alternative to HBUS_TARG_WRPTR, which is what Linux driver uses?
 */
#define SCD_QUEUE_WRPTR(x)           (SCD_START_OFFSET + 0x24 + (x) * 4)

/*
 * Queue (x) Read Pointers (indexes, really!), one for each Tx queue.
 * For FIFO mode, index indicates next frame to transmit.
 * For Scheduler-ACK mode, index indicates first frame in Tx window.
 * Initialized by driver, updated by scheduler.
 */
#define SCD_QUEUE_RDPTR(x)           (SCD_START_OFFSET + 0x64 + (x) * 4)

/*
 * Select which queues work in chain mode (1) vs. not (0).
 * Use chain mode to build chains of aggregated frames.
 * Bit fields:
 * 31-16:  Reserved
 * 15-00:  Mode, one bit for each queue -- 1: Chain mode, 0: one-at-a-time
 * NOTE:  If driver sets up queue for chain mode, it should be also set up
 *        Scheduler-ACK mode as well, via SCD_QUEUE_STATUS_BITS(x).
 */
#define SCD_QUEUECHAIN_SEL           (SCD_START_OFFSET + 0xd0)

/*
 * Select which queues interrupt driver when scheduler increments
 * a queue's read pointer (index).
 * Bit fields:
 * 31-16:  Reserved
 * 15-00:  Interrupt enable, one bit for each queue -- 1: enabled, 0: disabled
 * NOTE:  This functionality is apparently a no-op; driver relies on interrupts
 *        from Rx queue to read Tx command responses and update Tx queues.
 */
#define SCD_INTERRUPT_MASK           (SCD_START_OFFSET + 0xe4)

/*
 * Queue search status registers.  One for each queue.
 * Sets up queue mode and assigns queue to Tx DMA channel.
 * Bit fields:
 * 19-10: Write mask/enable bits for bits 0-9
 *     9: Driver should init to "0"
 *     8: Scheduler-ACK mode (1), non-Scheduler-ACK (i.e. FIFO) mode (0).
 *        Driver should init to "1" for aggregation mode, or "0" otherwise.
 *   7-6: Driver should init to "0"
 *     5: Window Size Left; indicates whether scheduler can request
 *        another TFD, based on window size, etc.  Driver should init
 *        this bit to "1" for aggregation mode, or "0" for non-agg.
 *   4-1: Tx FIFO to use (range 0-7).
 *     0: Queue is active (1), not active (0).
 * Other bits should be written as "0"
 *
 * NOTE:  If enabling Scheduler-ACK mode, chain mode should also be enabled
 *        via SCD_QUEUECHAIN_SEL.
 */
#define SCD_QUEUE_STATUS_BITS(x)     (SCD_START_OFFSET + 0x104 + (x) * 4)

/* Bit field positions */
#define SCD_QUEUE_STTS_REG_POS_ACTIVE		(0)
#define SCD_QUEUE_STTS_REG_POS_TXF		(1)
#define SCD_QUEUE_STTS_REG_POS_WSL		(5)
#define SCD_QUEUE_STTS_REG_POS_SCD_ACK		(8)

/* Write masks */
#define SCD_QUEUE_STTS_REG_POS_SCD_ACT_EN	(10)
#define SCD_QUEUE_STTS_REG_MSK			(0x0007FC00)

/**
 * 4965 internal SRAM structures for scheduler, shared with driver ...
 *
 * Driver should clear and initialize the following areas after receiving
 * "Alive" response from 4965 uCode, i.e. after initial
 * uCode load, or after a uCode load done for error recovery:
 *
 * SCD_CONTEXT_DATA_OFFSET (size 128 bytes)
 * SCD_TX_STTS_BITMAP_OFFSET (size 256 bytes)
 * SCD_TRANSLATE_TBL_OFFSET (size 32 bytes)
 *
 * Driver accesses SRAM via HBUS_TARG_MEM_* registers.
 * Driver reads base address of this scheduler area from SCD_SRAM_BASE_ADDR.
 * All OFFSET values must be added to this base address.
 */

/*
 * Queue context.  One 8-byte entry for each of 16 queues.
 *
 * Driver should clear this entire area (size 0x80) to 0 after receiving
 * "Alive" notification from uCode.  Additionally, driver should init
 * each queue's entry as follows:
 *
 * LS Dword bit fields:
 *  0-06:  Max Tx window size for Scheduler-ACK.  Driver should init to 64.
 *
 * MS Dword bit fields:
 * 16-22:  Frame limit.  Driver should init to 10 (0xa).
 *
 * Driver should init all other bits to 0.
 *
 * Init must be done after driver receives "Alive" response from 4965 uCode,
 * and when setting up queue for aggregation.
 */
#define SCD_CONTEXT_DATA_OFFSET			0x380
#define SCD_CONTEXT_QUEUE_OFFSET(x)	(SCD_CONTEXT_DATA_OFFSET + ((x) * 8))

#define SCD_QUEUE_CTX_REG1_WIN_SIZE_POS		(0)
#define SCD_QUEUE_CTX_REG1_WIN_SIZE_MSK		(0x0000007F)
#define SCD_QUEUE_CTX_REG2_FRAME_LIMIT_POS	(16)
#define SCD_QUEUE_CTX_REG2_FRAME_LIMIT_MSK	(0x007F0000)

/*
 * Tx Status Bitmap
 *
 * Driver should clear this entire area (size 0x100) to 0 after receiving
 * "Alive" notification from uCode.  Area is used only by device itself;
 * no other support (besides clearing) is required from driver.
 */
#define SCD_TX_STTS_BITMAP_OFFSET		0x400

/*
 * RAxTID to queue translation mapping.
 *
 * When queue is in Scheduler-ACK mode, frames placed in a that queue must be
 * for only one combination of receiver address (RA) and traffic ID (TID), i.e.
 * one QOS priority level destined for one station (for this wireless link,
 * not final destination).  The SCD_TRANSLATE_TABLE area provides 16 16-bit
 * mappings, one for each of the 16 queues.  If queue is not in Scheduler-ACK
 * mode, the device ignores the mapping value.
 *
 * Bit fields, for each 16-bit map:
 * 15-9:  Reserved, set to 0
 *  8-4:  Index into device's station table for recipient station
 *  3-0:  Traffic ID (tid), range 0-15
 *
 * Driver should clear this entire area (size 32 bytes) to 0 after receiving
 * "Alive" notification from uCode.  To update a 16-bit map value, driver
 * must read a dword-aligned value from device SRAM, replace the 16-bit map
 * value of interest, and write the dword value back into device SRAM.
 */
#define SCD_TRANSLATE_TBL_OFFSET		0x500

/* Find translation table dword to read/write for given queue */
#define SCD_TRANSLATE_TBL_OFFSET_QUEUE(x) \
	((SCD_TRANSLATE_TBL_OFFSET + ((x) * 2)) & 0xfffffffc)

#define SCD_TXFIFO_POS_TID			(0)
#define SCD_TXFIFO_POS_RA			(4)
#define SCD_QUEUE_RA_TID_MAP_RATID_MSK		(0x01FF)

/*********************** END TX SCHEDULER *************************************/

static inline u8 iwl4965_hw_get_rate(__le32 rate_n_flags)
{
	return le32_to_cpu(rate_n_flags) & 0xFF;
}
static inline u16 iwl4965_hw_get_rate_n_flags(__le32 rate_n_flags)
{
	return le32_to_cpu(rate_n_flags) & 0xFFFF;
}
static inline __le32 iwl4965_hw_set_rate_n_flags(u8 rate, u16 flags)
{
	return cpu_to_le32(flags|(u16)rate);
}


/**
 * Tx/Rx Queues
 *
 * Most communication between driver and 4965 is via queues of data buffers.
 * For example, all commands that the driver issues to device's embedded
 * controller (uCode) are via the command queue (one of the Tx queues).  All
 * uCode command responses/replies/notifications, including Rx frames, are
 * conveyed from uCode to driver via the Rx queue.
 *
 * Most support for these queues, including handshake support, resides in
 * structures in host DRAM, shared between the driver and the device.  When
 * allocating this memory, the driver must make sure that data written by
 * the host CPU updates DRAM immediately (and does not get "stuck" in CPU's
 * cache memory), so DRAM and cache are consistent, and the device can
 * immediately see changes made by the driver.
 *
 * 4965 supports up to 16 DRAM-based Tx queues, and services these queues via
 * up to 7 DMA channels (FIFOs).  Each Tx queue is supported by a circular array
 * in DRAM containing 256 Transmit Frame Descriptors (TFDs).
 */
#define IWL4965_MAX_WIN_SIZE              64
#define IWL4965_QUEUE_SIZE               256
#define IWL4965_NUM_FIFOS                  7
#define IWL_MAX_NUM_QUEUES                16


/**
 * struct iwl4965_tfd_frame_data
 *
 * Describes up to 2 buffers containing (contiguous) portions of a Tx frame.
 * Each buffer must be on dword boundary.
 * Up to 10 iwl_tfd_frame_data structures, describing up to 20 buffers,
 * may be filled within a TFD (iwl_tfd_frame).
 *
 * Bit fields in tb1_addr:
 * 31- 0: Tx buffer 1 address bits [31:0]
 *
 * Bit fields in val1:
 * 31-16: Tx buffer 2 address bits [15:0]
 * 15- 4: Tx buffer 1 length (bytes)
 *  3- 0: Tx buffer 1 address bits [32:32]
 *
 * Bit fields in val2:
 * 31-20: Tx buffer 2 length (bytes)
 * 19- 0: Tx buffer 2 address bits [35:16]
 */
struct iwl4965_tfd_frame_data {
	__le32 tb1_addr;

	__le32 val1;
	/* __le32 ptb1_32_35:4; */
#define IWL_tb1_addr_hi_POS 0
#define IWL_tb1_addr_hi_LEN 4
#define IWL_tb1_addr_hi_SYM val1
	/* __le32 tb_len1:12; */
#define IWL_tb1_len_POS 4
#define IWL_tb1_len_LEN 12
#define IWL_tb1_len_SYM val1
	/* __le32 ptb2_0_15:16; */
#define IWL_tb2_addr_lo16_POS 16
#define IWL_tb2_addr_lo16_LEN 16
#define IWL_tb2_addr_lo16_SYM val1

	__le32 val2;
	/* __le32 ptb2_16_35:20; */
#define IWL_tb2_addr_hi20_POS 0
#define IWL_tb2_addr_hi20_LEN 20
#define IWL_tb2_addr_hi20_SYM val2
	/* __le32 tb_len2:12; */
#define IWL_tb2_len_POS 20
#define IWL_tb2_len_LEN 12
#define IWL_tb2_len_SYM val2
} __attribute__ ((packed));


/**
 * struct iwl4965_tfd_frame
 *
 * Transmit Frame Descriptor (TFD)
 *
 * 4965 supports up to 16 Tx queues resident in host DRAM.
 * Each Tx queue uses a circular buffer of 256 TFDs stored in host DRAM.
 * Both driver and device share these circular buffers, each of which must be
 * contiguous 256 TFDs x 128 bytes-per-TFD = 32 KBytes for 4965.
 *
 * Driver must indicate the physical address of the base of each
 * circular buffer via the 4965's FH_MEM_CBBC_QUEUE registers.
 *
 * Each TFD contains pointer/size information for up to 20 data buffers
 * in host DRAM.  These buffers collectively contain the (one) frame described
 * by the TFD.  Each buffer must be a single contiguous block of memory within
 * itself, but buffers may be scattered in host DRAM.  Each buffer has max size
 * of (4K - 4).  The 4965 concatenates all of a TFD's buffers into a single
 * Tx frame, up to 8 KBytes in size.
 *
 * Bit fields in the control dword (val0):
 * 31-30: # dwords (0-3) of padding required at end of frame for 16-byte bound
 *    29: reserved
 * 28-24: # Transmit Buffer Descriptors in TFD
 * 23- 0: reserved
 *
 * A maximum of 255 (not 256!) TFDs may be on a queue waiting for Tx.
 */
struct iwl4965_tfd_frame {
	__le32 val0;
	/* __le32 rsvd1:24; */
	/* __le32 num_tbs:5; */
#define IWL_num_tbs_POS 24
#define IWL_num_tbs_LEN 5
#define IWL_num_tbs_SYM val0
	/* __le32 rsvd2:1; */
	/* __le32 padding:2; */
	struct iwl4965_tfd_frame_data pa[10];
	__le32 reserved;
} __attribute__ ((packed));


/**
 * struct iwl4965_queue_byte_cnt_entry
 *
 * Byte Count Table Entry
 *
 * Bit fields:
 * 15-12: reserved
 * 11- 0: total to-be-transmitted byte count of frame (does not include command)
 */
struct iwl4965_queue_byte_cnt_entry {
	__le16 val;
	/* __le16 byte_cnt:12; */
#define IWL_byte_cnt_POS 0
#define IWL_byte_cnt_LEN 12
#define IWL_byte_cnt_SYM val
	/* __le16 rsvd:4; */
} __attribute__ ((packed));


/**
 * struct iwl4965_sched_queue_byte_cnt_tbl
 *
 * Byte Count table
 *
 * Each Tx queue uses a byte-count table containing 320 entries:
 * one 16-bit entry for each of 256 TFDs, plus an additional 64 entries that
 * duplicate the first 64 entries (to avoid wrap-around within a Tx window;
 * max Tx window is 64 TFDs).
 *
 * When driver sets up a new TFD, it must also enter the total byte count
 * of the frame to be transmitted into the corresponding entry in the byte
 * count table for the chosen Tx queue.  If the TFD index is 0-63, the driver
 * must duplicate the byte count entry in corresponding index 256-319.
 *
 * "dont_care" padding puts each byte count table on a 1024-byte boundary;
 * 4965 assumes tables are separated by 1024 bytes.
 */
struct iwl4965_sched_queue_byte_cnt_tbl {
	struct iwl4965_queue_byte_cnt_entry tfd_offset[IWL4965_QUEUE_SIZE +
						       IWL4965_MAX_WIN_SIZE];
	u8 dont_care[1024 -
		     (IWL4965_QUEUE_SIZE + IWL4965_MAX_WIN_SIZE) *
		     sizeof(__le16)];
} __attribute__ ((packed));


/**
 * struct iwl4965_shared - handshake area for Tx and Rx
 *
 * For convenience in allocating memory, this structure combines 2 areas of
 * DRAM which must be shared between driver and 4965.  These do not need to
 * be combined, if better allocation would result from keeping them separate:
 *
 * 1)  The Tx byte count tables occupy 1024 bytes each (16 KBytes total for
 *     16 queues).  Driver uses SCD_DRAM_BASE_ADDR to tell 4965 where to find
 *     the first of these tables.  4965 assumes tables are 1024 bytes apart.
 *
 * 2)  The Rx status (val0 and val1) occupies only 8 bytes.  Driver uses
 *     FH_RSCSR_CHNL0_STTS_WPTR_REG to tell 4965 where to find this area.
 *     Driver reads val0 to determine the latest Receive Buffer Descriptor (RBD)
 *     that has been filled by the 4965.
 *
 * Bit fields val0:
 * 31-12:  Not used
 * 11- 0:  Index of last filled Rx buffer descriptor (4965 writes, driver reads)
 *
 * Bit fields val1:
 * 31- 0:  Not used
 */
struct iwl4965_shared {
	struct iwl4965_sched_queue_byte_cnt_tbl
	 queues_byte_cnt_tbls[IWL_MAX_NUM_QUEUES];
	__le32 val0;

	/* __le32 rb_closed_stts_rb_num:12; */
#define IWL_rb_closed_stts_rb_num_POS 0
#define IWL_rb_closed_stts_rb_num_LEN 12
#define IWL_rb_closed_stts_rb_num_SYM val0
	/* __le32 rsrv1:4; */
	/* __le32 rb_closed_stts_rx_frame_num:12; */
#define IWL_rb_closed_stts_rx_frame_num_POS 16
#define IWL_rb_closed_stts_rx_frame_num_LEN 12
#define IWL_rb_closed_stts_rx_frame_num_SYM val0
	/* __le32 rsrv2:4; */

	__le32 val1;
	/* __le32 frame_finished_stts_rb_num:12; */
#define IWL_frame_finished_stts_rb_num_POS 0
#define IWL_frame_finished_stts_rb_num_LEN 12
#define IWL_frame_finished_stts_rb_num_SYM val1
	/* __le32 rsrv3:4; */
	/* __le32 frame_finished_stts_rx_frame_num:12; */
#define IWL_frame_finished_stts_rx_frame_num_POS 16
#define IWL_frame_finished_stts_rx_frame_num_LEN 12
#define IWL_frame_finished_stts_rx_frame_num_SYM val1
	/* __le32 rsrv4:4; */

	__le32 padding1;  /* so that allocation will be aligned to 16B */
	__le32 padding2;
} __attribute__ ((packed));

#endif /* __iwl4965_4965_hw_h__ */