diff options
Diffstat (limited to 'release-notes/Apalis_T30_LinuxReleaseNotesV2.x.txt')
| -rw-r--r-- | release-notes/Apalis_T30_LinuxReleaseNotesV2.x.txt | 25 |
1 files changed, 14 insertions, 11 deletions
diff --git a/release-notes/Apalis_T30_LinuxReleaseNotesV2.x.txt b/release-notes/Apalis_T30_LinuxReleaseNotesV2.x.txt index 5313e03..c2bbb25 100644 --- a/release-notes/Apalis_T30_LinuxReleaseNotesV2.x.txt +++ b/release-notes/Apalis_T30_LinuxReleaseNotesV2.x.txt @@ -5,7 +5,7 @@ Release Notes: Linux Image V2.x for Apalis T30 Contents: - U-Boot 2015.04 boot loader - Linux 3.1.10 kernel, based on NVIDIA's Linux for Tegra (L4T) release R16.5 -- Angstrom/OpenEmbedded/Yocto 2014.12/dizzy/1.7 based root file system, using +- Angstrom 2014.12/OpenEmbedded dizzy/Yocto 1.7 based root file system, using LXDE desktop environment ==> Flashing instructions can be found at the very bottom of this release notes @@ -560,8 +560,8 @@ Initial Preparation: Flash eMMC: - EvalBoard V1.0a - - connect serial debug console to lower X28 or X29 using null modem RS-232 or - regular USB cable + - depending on JP10/12 connect serial debug console to lower X28 using null + modem RS-232 cable resp. X29 using a regular USB cable - insert above prepared SD card into SD/MMC 8bit (X18) or SD/MMC 4bit (X19) socket - Ixora V1.0a - connect serial debug console to X22 using null modem RS-232 cable and a @@ -574,17 +574,20 @@ Flash eMMC: - using SD/MMC 8bit (X18) socket on EvalBoard: setenv drive 1 setenv setupdate 'mmc dev ${drive}; mmc rescan; fatload mmc ${drive}:1 ${loadaddr} flash_blk.img; source ${loadaddr}' - save + saveenv - using SD/MMC 4bit (X19) socket on EvalBoard or micro SD card socket (X10) on Ixora: setenv drive 2 setenv setupdate 'mmc dev ${drive}; mmc rescan; fatload mmc ${drive}:1 ${loadaddr} flash_blk.img; source ${loadaddr}' - save + saveenv - use 'run setupdate' U-Boot command and then - - use 'run update' U-Boot command -- If you updated from an older image: - - power cycle or reset as requested and hit any key to stop auto booting - - use 'run setupdate' U-Boot command and then - - use 'run migrate_v2.3b2' U-Boot command + - use 'run update' U-Boot command unless you are updating from an older image + in which case: + - use 'run update_uboot' command and power cycle or reset and hit any key + to stop auto booting + - use 'env default -a' command followed by 'saveenv' command + - power cycle or reset again and hit any key to stop auto booting + - use 'run setupdate' U-Boot command and then + - use 'run migrate_v2.3b2' U-Boot command Boot from eMMC: - EvalBoard V1.0a or Ixora V1.0a @@ -610,4 +613,4 @@ If the boot loader on the module got corrupted this recovers it by loading U-Boo - run ./update.sh -d - stop at the U-Boot prompt and begin the update as stated above -Toradex, May 19, 2015 +Toradex, May 22, 2015 |