Clean up the TQM8xx_YYMHz configurations; allow to use the same

binary image for all clock frequencies. Implement run-time
optimization of flash access timing based on the actual bus
frequency.

11 files changed, 41 insertions, 356 deletions

diff --git a/include/common.h b/include/common.h
index 9645ef489c..a7a3a3a7b3 100644
--- a/include/common.h
+++ b/include/common.h
@@ -372,6 +372,7 @@ int	serial_tstc   (void);
 int	get_clocks (void);
 int	get_clocks_866 (void);
 int	sdram_adjust_866 (void);
+int	adjust_sdram_tbs_8xx (void);
 #if defined(CONFIG_8260)
 int	prt_8260_clks (void);
 #endif
diff --git a/include/configs/TQM823L.h b/include/configs/TQM823L.h
index c12f000f40..b1aced0732 100644
--- a/include/configs/TQM823L.h
+++ b/include/configs/TQM823L.h
@@ -262,15 +262,8 @@
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
  */
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_PLPRCR							\
-		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else			/* up to 66 MHz we use a 1:1 clock */
 #define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
@@ -279,17 +272,9 @@
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_SCCR	(/* SCCR_TBS  | */ \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#else			/* up to 66 MHz we use a 1:1 clock */
-#define CFG_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+#define CFG_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * PCMCIA stuff
@@ -358,19 +343,8 @@
 /*
  * FLASH timing:
  */
-#if   defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | 0       | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
 #define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else		/*   50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif	/*CONFIG_??MHz */
 
 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
@@ -431,13 +405,9 @@
  * 66 Mhz => 66.000.000 / Divider = 129
  * 80 Mhz => 80.000.000 / Divider = 156
  */
-#if   defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CFG_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
+
+#define CFG_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA	98
 
 /*
  * For 16 MBit, refresh rates could be 31.3 us
diff --git a/include/configs/TQM823M.h b/include/configs/TQM823M.h
index 7ca9153207..0c2dbec644 100644
--- a/include/configs/TQM823M.h
+++ b/include/configs/TQM823M.h
@@ -254,15 +254,8 @@
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
  */
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_PLPRCR							\
-		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else			/* up to 66 MHz we use a 1:1 clock */
 #define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
@@ -271,17 +264,9 @@
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_SCCR	(/* SCCR_TBS  | */ \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#else			/* up to 66 MHz we use a 1:1 clock */
-#define CFG_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+#define CFG_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * PCMCIA stuff
@@ -350,19 +335,8 @@
 /*
  * FLASH timing:
  */
-#if   defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | 0       | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
 #define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else		/*   50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif	/*CONFIG_??MHz */
 
 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
@@ -423,13 +397,9 @@
  * 66 Mhz => 66.000.000 / Divider = 129
  * 80 Mhz => 80.000.000 / Divider = 156
  */
-#if   defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CFG_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
+
+#define CFG_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA	98
 
 /*
  * For 16 MBit, refresh rates could be 31.3 us
diff --git a/include/configs/TQM850L.h b/include/configs/TQM850L.h
index 29524478f6..d6784c8e0e 100644
--- a/include/configs/TQM850L.h
+++ b/include/configs/TQM850L.h
@@ -245,15 +245,8 @@
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
  */
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_PLPRCR							\
-		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else			/* up to 66 MHz we use a 1:1 clock */
 #define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
@@ -262,17 +255,9 @@
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_SCCR	(/* SCCR_TBS  | */ \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#else			/* up to 66 MHz we use a 1:1 clock */
-#define CFG_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+#define CFG_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * PCMCIA stuff
@@ -341,19 +326,8 @@
 /*
  * FLASH timing:
  */
-#if   defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | 0       | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
 #define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else		/*   50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif	/*CONFIG_??MHz */
 
 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
@@ -414,13 +388,9 @@
  * 66 Mhz => 66.000.000 / Divider = 129
  * 80 Mhz => 80.000.000 / Divider = 156
  */
-#if   defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CFG_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
+
+#define CFG_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA	98
 
 /*
  * For 16 MBit, refresh rates could be 31.3 us
diff --git a/include/configs/TQM850M.h b/include/configs/TQM850M.h
index d565300506..e825ac939e 100644
--- a/include/configs/TQM850M.h
+++ b/include/configs/TQM850M.h
@@ -244,15 +244,8 @@
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
  */
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_PLPRCR							\
-		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else			/* up to 66 MHz we use a 1:1 clock */
 #define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
@@ -261,17 +254,9 @@
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_SCCR	(/* SCCR_TBS  | */ \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#else			/* up to 66 MHz we use a 1:1 clock */
-#define CFG_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+#define CFG_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * PCMCIA stuff
@@ -340,19 +325,8 @@
 /*
  * FLASH timing:
  */
-#if   defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | 0       | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
 #define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else		/*   50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif	/*CONFIG_??MHz */
 
 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
@@ -413,13 +387,9 @@
  * 66 Mhz => 66.000.000 / Divider = 129
  * 80 Mhz => 80.000.000 / Divider = 156
  */
-#if   defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CFG_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
+
+#define CFG_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA	98
 
 /*
  * For 16 MBit, refresh rates could be 31.3 us
diff --git a/include/configs/TQM855L.h b/include/configs/TQM855L.h
index 2608119537..9c06d482c3 100644
--- a/include/configs/TQM855L.h
+++ b/include/configs/TQM855L.h
@@ -248,15 +248,8 @@
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
  */
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_PLPRCR							\
-		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else			/* up to 66 MHz we use a 1:1 clock */
 #define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
@@ -265,17 +258,9 @@
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_SCCR	(/* SCCR_TBS  | */ \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#else			/* up to 66 MHz we use a 1:1 clock */
-#define CFG_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+#define CFG_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * PCMCIA stuff
@@ -344,19 +329,8 @@
 /*
  * FLASH timing:
  */
-#if   defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | 0       | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
 #define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else		/*   50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif	/*CONFIG_??MHz */
 
 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
@@ -417,13 +391,9 @@
  * 66 Mhz => 66.000.000 / Divider = 129
  * 80 Mhz => 80.000.000 / Divider = 156
  */
-#if   defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CFG_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
+
+#define CFG_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA	98
 
 /*
  * For 16 MBit, refresh rates could be 31.3 us
diff --git a/include/configs/TQM855M.h b/include/configs/TQM855M.h
index cb4a16abdc..82a855bd04 100644
--- a/include/configs/TQM855M.h
+++ b/include/configs/TQM855M.h
@@ -283,15 +283,8 @@
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
  */
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_PLPRCR							\
-		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else			/* up to 66 MHz we use a 1:1 clock */
 #define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
@@ -300,17 +293,9 @@
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_SCCR	(/* SCCR_TBS  | */ \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#else			/* up to 66 MHz we use a 1:1 clock */
-#define CFG_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+#define CFG_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * PCMCIA stuff
@@ -379,19 +364,8 @@
 /*
  * FLASH timing:
  */
-#if   defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | 0       | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
 #define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else		/*   50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif	/*CONFIG_??MHz */
 
 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
@@ -452,13 +426,9 @@
  * 66 Mhz => 66.000.000 / Divider = 129
  * 80 Mhz => 80.000.000 / Divider = 156
  */
-#if   defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CFG_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
+
+#define CFG_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA	98
 
 /*
  * For 16 MBit, refresh rates could be 31.3 us
diff --git a/include/configs/TQM860L.h b/include/configs/TQM860L.h
index ba2198f0a0..adac808e73 100644
--- a/include/configs/TQM860L.h
+++ b/include/configs/TQM860L.h
@@ -249,15 +249,8 @@
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
  */
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_PLPRCR							\
-		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else			/* up to 66 MHz we use a 1:1 clock */
 #define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
@@ -266,17 +259,9 @@
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_SCCR	(/* SCCR_TBS  | */ \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#else			/* up to 66 MHz we use a 1:1 clock */
-#define CFG_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+#define CFG_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * PCMCIA stuff
@@ -345,19 +330,8 @@
 /*
  * FLASH timing:
  */
-#if   defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | 0       | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
 #define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else		/*   50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif	/*CONFIG_??MHz */
 
 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
@@ -418,13 +392,9 @@
  * 66 Mhz => 66.000.000 / Divider = 129
  * 80 Mhz => 80.000.000 / Divider = 156
  */
-#if   defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CFG_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
+
+#define CFG_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA	98
 
 /*
  * For 16 MBit, refresh rates could be 31.3 us
diff --git a/include/configs/TQM860M.h b/include/configs/TQM860M.h
index 3f6edb8040..1e9abc81c6 100644
--- a/include/configs/TQM860M.h
+++ b/include/configs/TQM860M.h
@@ -250,15 +250,8 @@
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
  */
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_PLPRCR							\
-		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else			/* up to 66 MHz we use a 1:1 clock */
 #define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
@@ -267,17 +260,9 @@
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_SCCR	(/* SCCR_TBS  | */ \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#else			/* up to 66 MHz we use a 1:1 clock */
-#define CFG_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+#define CFG_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
-#endif	/* CONFIG_80MHz */
 
 /*-----------------------------------------------------------------------
  * PCMCIA stuff
@@ -346,19 +331,8 @@
 /*
  * FLASH timing:
  */
-#if   defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | 0       | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
 #define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else		/*   50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif	/*CONFIG_??MHz */
 
 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
@@ -419,13 +393,9 @@
  * 66 Mhz => 66.000.000 / Divider = 129
  * 80 Mhz => 80.000.000 / Divider = 156
  */
-#if   defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CFG_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
+
+#define CFG_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA	98
 
 /*
  * For 16 MBit, refresh rates could be 31.3 us
diff --git a/include/configs/TQM862L.h b/include/configs/TQM862L.h
index 84570c1c55..595d4a26b5 100644
--- a/include/configs/TQM862L.h
+++ b/include/configs/TQM862L.h
@@ -252,16 +252,8 @@
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit
- *
- * If this is a 80 MHz or 100 MHz CPU,
- * set PLL multiplication factor to 5 (5 * 16 = 80, 5 * 20 = 100)
  */
-#if defined(CONFIG_80MHz) || defined(CONFIG_100MHz)
-#define CFG_PLPRCR							\
-		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else			/* up to 66 MHz we use a 1:1 clock */
 #define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif	/* CONFIG_80MHz | CONFIG_100MHz */
 
 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
@@ -270,17 +262,9 @@
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
-#if defined(CONFIG_80MHz) || defined(CONFIG_100MHz) /* use 16/20 MHz * 5 */
-#define CFG_SCCR	(/* SCCR_TBS  | */ \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#else			/* up to 66 MHz we use a 1:1 clock */
-#define CFG_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+#define CFG_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
-#endif	/* CONFIG_80MHz | CONFIG_100MHz */
 
 /*-----------------------------------------------------------------------
  * PCMCIA stuff
@@ -349,24 +333,8 @@
 /*
  * FLASH timing:
  */
-#if defined(CONFIG_100MHz)
-/* 100 MHz CPU - 50 MHz bus:
- * ACS = 01, TRLX = 0, CSNT = 0, SCY = 7, EHTR = 0 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV4  | OR_SCY_7_CLK | OR_BI)
-#elif defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus:
- * ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | 0       | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
 #define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else		/*   50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif	/*CONFIG_??MHz */
 
 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
@@ -428,15 +396,9 @@
  *  80 Mhz =>  80.000.000 / Divider = 156
  * 100 Mhz => 100.000.000 / Divider = 195
  */
-#if   defined(CONFIG_100MHz)
-#define CFG_MAMR_PTA		195
-#elif defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CFG_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
+
+#define CFG_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA	98
 
 /*
  * For 16 MBit, refresh rates could be 31.3 us
diff --git a/include/configs/TQM862M.h b/include/configs/TQM862M.h
index 914e28a82c..7ab8559ebf 100644
--- a/include/configs/TQM862M.h
+++ b/include/configs/TQM862M.h
@@ -253,16 +253,8 @@
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit
- *
- * If this is a 80 MHz or 100 MHz CPU,
- * set PLL multiplication factor to 5 (5 * 16 = 80, 5 * 20 = 100)
  */
-#if defined(CONFIG_80MHz) || defined(CONFIG_100MHz)
-#define CFG_PLPRCR							\
-		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else			/* up to 66 MHz we use a 1:1 clock */
 #define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif	/* CONFIG_80MHz | CONFIG_100MHz */
 
 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
@@ -271,17 +263,9 @@
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
-#if defined(CONFIG_80MHz) || defined(CONFIG_100MHz) /* use 16/20 MHz * 5 */
-#define CFG_SCCR	(/* SCCR_TBS  | */ \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#else			/* up to 66 MHz we use a 1:1 clock */
-#define CFG_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+#define CFG_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
-#endif	/* CONFIG_80MHz | CONFIG_100MHz */
 
 /*-----------------------------------------------------------------------
  * PCMCIA stuff
@@ -350,24 +334,8 @@
 /*
  * FLASH timing:
  */
-#if defined(CONFIG_100MHz)
-/* 100 MHz CPU - 50 MHz bus:
- * ACS = 01, TRLX = 0, CSNT = 0, SCY = 7, EHTR = 0 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV4  | OR_SCY_7_CLK | OR_BI)
-#elif defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus:
- * ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | 0       | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
 #define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else		/*   50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif	/*CONFIG_??MHz */
 
 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
@@ -429,15 +397,9 @@
  *  80 Mhz =>  80.000.000 / Divider = 156
  * 100 Mhz => 100.000.000 / Divider = 195
  */
-#if   defined(CONFIG_100MHz)
-#define CFG_MAMR_PTA		195
-#elif defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CFG_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
+
+#define CFG_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
+#define CFG_MAMR_PTA	98
 
 /*
  * For 16 MBit, refresh rates could be 31.3 us