summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2024-01-24toradex: tdx-cfg-block: Add new apalis and colibri pidtoradex_2020.07Joao Paulo Goncalves
Add new apalis imx6 and colibri imx6/imx7 products IDs. Upstream-Status: Submitted [https://lore.kernel.org/u-boot/20240122200930.673447-1-jpaulo.silvagoncalves@gmail.com/] Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
2023-06-14colibri_imx6: fix RALAT and WALAT valuesStefan Eichenberger
Running a memtest in U-Boot and Linux shows that some Colibri iMX6 produce bitflips at temperatures above 60°C. This happens because the RALAT and WALAT values on the Colibri iMX6 are too low. The problems were introduced by commit 09dbac8174c4 ("mx6: ddr: Restore ralat/walat in write level calibration") before the calibration process overwrote the values and set them to the maximum value. With this commit, we make sure that the RALAT and WALAT values are set to the maximum values again. This has been proven to work for years. Upstream-Status: Submitted [https://lore.kernel.org/all/20230614090137.17626-1-francesco@dolcini.it/] Fixes: 09dbac8174c4 ("mx6: ddr: Restore ralat/walat in write level calibration") Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
2023-02-15configs: colibri-imx7-tezi: Fix bad block table in flash configurationStefan Eichenberger
Make sure that the bad block table in flash is used on Colibri iMX7 for Tezi. Without this configuration enabled U-Boot corrupts the bad block table and Linux will update the table on each reboot. The corruption occurs because if CONFIG_SYS_NAND_USE_FLASH_BBT is not set, U-boot will store bad blocks out of band, while the Linux driver for the iMX7 will store them in band in a bad block table. Upstream-Status: Inappropriate [other] - There is no tezi specific defconfig upstream - The non tezi specific configuration is submitted see [https://lore.kernel.org/all/20230210103351.22907-1-francesco@dolcini.it/] Related-to: ELB-4989 Fixes: fd8c1fc9430 ("arm: dts: imx7: colibri: add raw NAND support") Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
2023-02-12configs: colibri-imx7: Fix bad block table in flash configurationStefan Eichenberger
Make sure that the bad block table in flash is used on Colibri iMX7. Without this configuration enabled U-Boot corrupts the bad block table and Linux will update the table on each reboot. The corruption occurs because if CONFIG_SYS_NAND_USE_FLASH_BBT is not set, U-boot will store bad blocks out of band, while the Linux driver for the iMX7 will store them in band in a bad block table. Upstream-Status: Submitted [https://lore.kernel.org/all/20230210103351.22907-1-francesco@dolcini.it/] Related-to: ELB-4989 Fixes: fd8c1fc9430 ("arm: dts: imx7: colibri: add raw NAND support") Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
2023-02-09arch: arm: colibri_imx6: set specific soc typeMax Krummenacher
This indirectly enables ARM errata 751472, 794072, 761320, 845369 which all apply to Colibri iMX6. Upstream-Status: Backport [f27ffe4177a7cc09614e2f87012234c1e260c8f2] Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2022-06-27board: apalis_imx6: DDR init using mx6_dram_cfg()Francesco Dolcini
Do DDR initialization using the procedural mx6_dram_cfg() instead of programming the MMDC using a raw list of register/value pairs, this solves some rare boot failures on specific "bad" modules. Calibration values, DDR geometry are unchanged, memory timings are updated according to the relevant memory datasheet, no changes on the power consumption. For IT temperature range SKUs CL is decreased from 8 to 7 and tFAW value is increased, for commercial temperature range SKUs some changes on ODT parameters. This change was validated over a range of different apalis-imx6 SoM, on the whole working temperature range with weeks of continuous testing. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2022-06-27mx6: ddr: Fix disabling on-die terminationFrancesco Dolcini
In case rtt_nom is set to 0 keep ODT disabled (MMDC MPODTCTRL = 0). No changes required for DDR MR1 Rtt_Nom impedance register, 0 value is already handled correctly. No board is currently affected by this change (rtt_nom != 0 on all i.MX6 ddr3 boards), this will be used by a follow-up change. Fixes: fe0f7f7842e1 ("mx6: add mmdc configuration for MX6Q/MX6DL") Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2022-06-27mx6: ddr: Wait before issuing the first MRS cmdFrancesco Dolcini
Upstream commit aa42894471ae6a4e57692f6912690489a1587019 Wait 1ms before issuing the first MRS command to write DDR3 Mode registers. There is a requirement to wait a minimum time before issuing command to the DDR3 device, according to the JEDEC standard this time is 500us (after RESET_n is de-asserted until CKE becomes active) + tXPR (Reset CKE Exit time, maximum value 360ns). It seems that for some reason this is not enforced by the MMDC controller. Without this change we experienced random memory initialization failures with about 2% boot failure rate on specific problematic boards, after this change we were able to do more than 10.000 power-cycle without a single failure. Fixes: fe0f7f7842e1 ("mx6: add mmdc configuration for MX6Q/MX6DL") Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-06-27mx6: ddr: Restore ralat/walat in write level calibrationFrancesco Dolcini
Upstream commit 09dbac8174c47c6d547c7ab84601fc3424c71dc8 The current DDR write level calibration routine always overwrite the ralat/walat fields to their maximum value, just save the existing values at the beginning of the calibration routine and restore it at the end. In case the delay is estimated by the user to be more than one cycle the walat should be configured according to that, this is not automatically done. From the i.MX6 RM: The user should read the results of the associated delay-line at MPWLDECTRL#[WL_DL_ABS_OFFSET#] and in case the user estimates that the reasonable delay may be above 1 cycle then the user should indicate it at MPWLDECTRL#[WL_CYC_DEL#]. Moreover the user should indicate it in MDMISC[WALAT] field. For example, if the result of the write leveling calibration is 100/256 parts of a cycle, but the user estimates that the delay is above 2 cycles then MPWLDECTRL#[WL_CYC_DEL#] should be configured to 2, so the total delay will be 2 and 100/256 parts of a cycle Probably it would just possible to not overwrite the mdmisc register in the first place, since this is not present in the write_level_calib() example in NXP AN4467 nor in the i.MX6 RM (44.11.6.1 Hardware Write Leveling Calibration). Fixes: d339f16911c7 ("arm: imx6: Add DDR3 calibration code for MX6 Q/D/DL") Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-06-24toradex: apalis/colibri_imx6: Fix CLKO1/CLKO2 outputFrancesco Dolcini
Set CLK01 and CLK02 to 24MHz and enable it in CCM_CCOSR register. This clock is used by both the audio codec (CLKO1) and by the CSI camera (CLKO2) and is expected to be 24MHz. Despite the wrong 16.5MHz there was no real issue because of the wrong frequency since Linux reconfigures the clocks afterward, however this was triggering an issue with noise coming from the SGTL5000 audio codec. The problem is that the SGTL5000 does not have a reset pin and after it is configured if the input MCLK clock is disabled it produces a constant noise on its output, this was happening on software reboot. Forcing the clock to be enabled in U-Boot prevent the problem by making sure that the clock is always available, without this change as soon as Linux was changing the clock tree (setting clk_out_sel=1 without setting clko2_en=1) the noise would start till the actual clock was enabled (clko2_en=1) during the SGTL5000 driver probe. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2022-06-20toradex: tdx-cfg-block: add new toradex oui rangePhilippe Schenker
[ backported from https://lists.denx.de/pipermail/u-boot/2022-June/486993.html ] Add new Toradex MAC OUI (8c:06:cb), to the config block. With this change we extend the possible serial-numbers as follows: For serial-numbers 00000000-16777215 OUI 00:14:2d is taken For serial-numbers 16777216-33554431 OUI 8c:06:cb is taken Lower 24-bit of the serial number are used in the NIC part of the MAC address, the complete serial number can be calculated using the OUI. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> [ps: use kdiff3 to autoresolve conflicts]
2022-06-14toradex: tdx-cfg-block: extend assembly versionPhilippe Schenker
i[ backport https://lists.denx.de/pipermail/u-boot/2022-June/486350.html ] There are two decimal digits reserved to encode the module version and revision. This code so far implemented A-Z which used 0-25 of this range. This commit extends the range to make use of all 99 numbers. After capital letters the form with a hashtag and number (e.g. #26) is used. Examples: If the assembly version is between zero and 25 the numbering is as follows, as it also has been before this commit: 0: V0.0A 1: V0.0B ... 25: V0.0Z New numbering of assembly version: If the number is between 26 and 99 the new assembly version name is: 26: V0.0#26 27: V0.0#27 ... 99: V0.0#99 Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> [ps: backport: replace dectoul() with simple_strtoul()]
2022-06-14toradex: tdx-cfg-block: use defines for string lengthPhilippe Schenker
[ backport https://lists.denx.de/pipermail/u-boot/2022-June/486349.html ] With those defines the length can be reused and is in one place extendable. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2022-06-14toradex: tdx-cfg-block: use only snprintfPhilippe Schenker
[ backport https://lists.denx.de/pipermail/u-boot/2022-June/486348.html ] Prevent memory issues that could appear with sprintf. Replace all sprintf occurences with snprintf. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2022-06-07fdt: Add U-Boot version to chosen nodeFrancesco Dolcini
commit 622ecee93a604c017aca23906c5cc903b4002b78 upstream. Add a new device tree property "u-boot,version" in the chosen node to pass the U-Boot version to the operating system. This can be useful to implement a firmware upgrade procedure from the operating system. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2022-05-10imx: mx6ull: fix REFTOP_VBGADJ settingDario Binacchi
[ Upstream commit c1af358cf51a85ed8c47fc576d3cae34196ec47f ] The previous code wrote the contents of the fuse as is in the REFTOP_VBGADJ[2:0], but this was wrong if you consider the contents of the table in the code comment. This table is also different from the table in the commit description. But then, which of the two is correct? If it is assumed that an unprogrammed fuse has a value of 0 then for backward compatibility of the code REFTOP_VBGADJ[2:0] must be set to 6 (b'110). Therefore, the table in the code comment can be considered correct as well as this patch. Fixes: 97c16dc8bf098 ("imx: mx6ull: update the REFTOP_VBGADJ setting") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
2022-04-04apalis-tk1: fix tezi fit image configuration nameMax Krummenacher
The Toradex Easy Installer uses a fitimage for kernel/fdt/rootfs. With moving to the meta-toradex-bsp-common fitimage class to create the fitimage the configuration name is changed. For the Apalis TK1 used in recovery mode we set the configuration used in the U-Boot environment. Change that to the new name. Related-to: ELB-4417 Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2022-04-04colibri_imx7: fix tezi fit image configuration nameMax Krummenacher
The Toradex Easy Installer uses a fitimage for kernel/fdt/rootfs. With moving to the meta-toradex-bsp-common fitimage class to create the fitimage the configuration name is changed. For the Colibri iMX7 with RawNAND we set the configuration used in the U-Boot environment. Change that to the new name. Related-to: ELB-4417 Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2022-03-28gitlab-ci: fix u-boot-test-hooks to specific versionPhilippe Schenker
The latest master tests do no longer pass. So use the state from September 2020 Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2022-03-28uboot-test-hooks: Switch to our GitLab instanceTom Rini
As Stephen is no longer actively maintaining the uboot-test-hooks repository, switch to using the instance on our GitLab. Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Rini <trini@konsulko.com> (cherry picked from commit 85ae52b9593894fa31d80d83d76bdb3b6432c4be)
2022-03-28gitlab-ci: update containerPhilippe Schenker
We got an error that triggered a rebuild of the container. Since it got updated to the one used also upstream by Oleksandr use this new one Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2022-02-14colibri-imx7: remove hard-coded variantMarcel Ziswiler
Remove hard-coded variant in the eMMC build case as since the following commit it will anyway always get overridden by the detection routing in board code. eee9c9f11383 ("board: colibri_imx7: Set variant variable also for non-emmc variants") Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-02-14board: colibri_imx7_emmc: fix emmc detectionMarcel Ziswiler
Later Colibri iMX7D V1.1B modules are using a “new” SoC fusing. The difference has to do with whether or not we do enable the boot ROM to enable/use the eMMC reset signal. Depending on that SoC fuse, the boot ROM configures this pin as a GPIO output to actually be able to do/drive the reset signal. Our eMMC vs. NAND detection so far only sets that signal to a GPIO but without explicitly setting any direction as, of course, so far, by default, it was an input. As the boot ROM now sets it as an output we do get back a value of zero instead of a one which would indicate the pull-up being present on eMMC modules. Fix this by setting the SION bit which allows reading back the value even if it is set to be an output by the boot ROM. Note that with the new SoC fusing we now read back what the boot ROM drived rather than the real value caused by the pull-up resistor. However, if it would ever be driven low the eMMC would anyway permanently be reset. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2021-12-28board: colibri-imx6ull: fix detecting ethernet phyPhilippe Schenker
now that it is possible to use regulator-fixed-clock make use of it. This makes U-Boot detect the PHY on first cold-boot. This commit also adjusts the code in setup_fec and follows how it is done in mx6ullevk.c This commit also slows down the boot-process by about 150ms as it now waits for the regulator-fixed-clock voltage that drives the PHY to go up. If you rely on very fast boot-speeds and don't need ethernet for your boot-process you can safely revert the changes on imx6ull-colibri.dtsi Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2021-12-28regulator: fixed: add possibility to enable by clockPhilippe Schenker
This commit adds the possibility to choose the compatible "regulator-fixed-clock" in devicetree. This is a special case of regulator-fixed where a clock has to be used to switch the regulator on and off. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2021-11-15configs: tdx: Do not overwrite fdtfile if it got set manuallyPhilippe Schenker
In case a customer wants to set fdtfile currently preboot overrides it always with preboot just before the bootdelay. Use test -n to check if fdtfile is already set and only set it if nothing got touched manually Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2021-11-12board: colibri-imx6ull: Do not leave variant variable unsetPhilippe Schenker
Toradex uses the variable variant to distinguish between modules with eMMC, NAND with wifi and NAND without wifi. This variable is set on every boot. Set this variable also if we have a NAND module without wifi to prevent issues. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2021-11-12board: colibri_imx7: Set variant variable also for non-emmc variantsPhilippe Schenker
Toradex uses the variable variant to distinguish between eMMC or NAND modules. This variable is set on every boot. Set this variable also if we have a NAND module to prevent issues. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2021-11-04apalis-tk1: avoid save environment unaskedDenys Drozdov
U-boot should never save the environment unasked. Avoid storing broken ftd_module to flash Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
2021-11-04apalis-imx6: avoid save environment unaskedDenys Drozdov
u-boot should never save the environment unasked. Avoid storing broken ftd_file to eMMC Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
2021-10-12colibri-imx6ull: fix setup of nand gpmi clockPhilippe Schenker
NXP used to setup the gpmi clock root from gpmi_clk in early versions in their downstream BSP. [1] However on mainline the gpmi clock root was always setup from enfc since the beginning of the i.MX 6 series SoCs, which is still the same today. [2] NXP followed the mainline approach at some point and changed setup_gpmi_io_clk to setup gpmi clock root from enfc which left faulty code behind in our board file. [3] This commit follows the change of NXP as it improves the performance of the NAND from ~1.2 MiB/s to ~12 MiB/s. [3] This change was verified to work in recovery-mode and u-boot loaded from NAND on all four Colibri iMX6ULL SKUs from Toradex. The frequency used to read the NAND, measured on RE# (Read Enable): before this patch: 1.4 MHz after this patch: 22 MHz in Linux Kernel: 50 MHz [1] https://source.codeaurora.org/external/imx/uboot-imx/tree/arch/arm/cpu/armv7/mx6/clock.c?h=nxp/imx_v2016.03_4.1.15_2.0.0_ga#n62 [2] 23608e23fd65 (i.mx: add the initial support for freescale i.MX6Q processor) [3] https://source.codeaurora.org/external/imx/uboot-imx/commit/?id=7a82a19ceabfb04bbc1591a67c99751748781c7d Related-to: ELB-4176 Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2021-10-12colibri-imx7: remove vidargs for emmc variantDenys Drozdov
Default vidargs are set to 640x480@60 which causes incorrect lt161010 touchscreen resolution. eMMC variant should use overlays to select proper touchscreen timing and resolution Related-to: ELB-4191 Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
2021-10-11colibri_imx7: tezi: move CONFIG_BOOTCOMMAND from header to defconfigMax Krummenacher
Completes / fixes commit cbc67000af2 ("colibri_imx7: move CONFIG_BOOTCOMMAND from header to defconfig"). Without this if U-Boot is configured with colibri_imx7_tezi_defconfig CONFIG_BOOTCOMMAND defaults to 'run distro_boot' which fails on this NAND module. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2021-10-11colibri-imx6ull: tezi: move CONFIG_BOOTCOMMAND from header to defconfigMax Krummenacher
Completes / fixes commit 1e9685556d2 ("colibri-imx6ull: move CONFIG_BOOTCOMMAND from header to defconfig"). Without this if U-Boot is configured with colibri-imx6ull_tezi_defconfig CONFIG_BOOTCOMMAND defaults to 'run distro_boot' which fails on this NAND module. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2021-10-05colibri-imx7: move CONFIG_BOOTCOMMAND from header to defconfigMing Liu
Move CONFIG_BOOTCOMMAND definition from colibri_imx7.h to colibri_imx7_defconfig, to be more flexible, for instance, it could be overridden by merge_config.sh script. Signed-off-by: Ming Liu <ming.liu@toradex.com>
2021-10-05colibri-imx6ull: move CONFIG_BOOTCOMMAND from header to defconfigMing Liu
Move CONFIG_BOOTCOMMAND definition from colibri-imx6ull.h to colibri-imx6ull_defconfig, to be more flexible, for instance, it could be overridden by merge_config.sh script. Signed-off-by: Ming Liu <ming.liu@toradex.com>
2021-09-21colibri-imx6ull: reset vidargs env variableMarcel Ziswiler
Unfortunately, vidargs cause very suboptimal display timings to be calculated which destroys our nice VESA VGA definition from the device tree. Get rid of it. Related-to: ELB-4080 Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2021-09-20ARM: dts: colibri-imx6ull: fix mac address passingFrancesco Dolcini
colibri-imx6ull ethernet device is fec2, while the optional secondary ethernet is fec1, update the ethernet aliases in the .dts file so that ethaddr is set to fec2 and eth1addr to fec1. Without this change the ethernet interfaces have a different mac address between Linux and U-Boot. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2021-09-10disk: part: add the device search failed log msgOleksii Bidnichenko
Add missing error message to blk_get_device_part_str. Related-to: ELB-4082 Signed-off-by: Oleksii Bidnichenko <oleksii.bidnichenko@toradex.com> (cherry picked from commit 866d51e3fde2771d0e83a6ea831b84a2cbc66fd1)
2021-09-10mmc: merge upstream __mmc_switch fixesOleksii Bidnichenko
commit 8e2b0af7216d78b60fccb46a107a4a047938aea9 upstream. commit ef5ab0d13a7a44469f6c765c8acc8d54c23213de upstream. Update a __mmc_switch MMC_STATUS_SWITCH_ERROR notification level from debug to error. Related-to: ELB-4082 Signed-off-by: Oleksii Bidnichenko <oleksii.bidnichenko@toradex.com> (cherry picked from commit 675f0f6db0de49316f839f6e9fcbc6f2a007b7d8)
2021-09-06cfgblock: extend get_cfgblock_interactiveOleksii Bidnichenko
- Correct the hardware product id for the Colibri IMX7D (eMMC) module. - Exclude IT check since Colibri IMX7D (eMMC) is always IT. Related-to: ELB-4076 Signed-off-by: Oleksii Bidnichenko <oleksii.bidnichenko@toradex.com>
2021-09-01colibri-imx7: improve env badblock managementFrancesco Dolcini
Use the complete 512kb (4 blocks) nand partition reserved for u-boot environment instead of just the first block, this allows the module to have a working environment even if 3 blocks are bad. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2021-09-01colibri-imx6ull: improve env badblock managementFrancesco Dolcini
Use the complete 512kb (4 blocks) nand partition reserved for u-boot environment instead of just the first block, this allows the module to have a working environment even if 3 blocks are bad. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2021-08-30colibri-imx6ull: reset vidargs env variableOleksii Bidnichenko
The "vidargs" variable is needed only if the board is not aware of the display that is connected to it. Since the EMMC version with the usage of overlays is able to specify display settings, such a variable becomes redundant. Related-to: ELB-4065
2021-08-20apalis-imx6: use dynamic DDR calibrationFrancesco Dolcini
Enable dynamic DDR calibration to have a reliable behavior on edge temperatures conditions. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2021-08-20colibri-imx6: use dynamic DDR calibrationFrancesco Dolcini
Enable dynamic DDR calibration to have a reliable behavior on edge temperatures conditions. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2021-08-12colibri-imx6ull: add tezi recovery configMax Krummenacher
This configuration creates an U-Boot which does not use any storage device, i.e. no eMMC or NAND. It is used to boot U-Boot over recovery aka. Serial Downloader without the need to know if the module uses eMMC or NAND for storage. It detects the storage device type and start the Toradex Easy Installer with the matching configuration. Note that for NAND devices the mtd partitioning is not patched into the device tree by U-Boot. It must be part of the provided device tree. Related-to: TEI-922 Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2021-08-12colibri-imx6ull-emmc: add tezi configMax Krummenacher
This configuration creates an U-Boot which is installed on eMMC to then boot the Toradex Easy Installer. Related-to: TEI-922 Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2021-07-29toradex: tdx-cfg-block: add colibri imx6ull emmc variantMax Krummenacher
While at it complete the list of the known module product ids. Related-to: ELB-4056, ELB-4057 Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2021-07-29toradex: tdx-cfg-block: fix verdin handlingMax Krummenacher
| #if !defined(CONFIG_TARGET_VERDIN_IMX8MM) || !defined(CONFIG_TARGET_VERDIN_IMX8MN) is never false. Fix that so that the condition is 'true' for any board but the two verdins. Fixes commit c0c3978cba3 ("toradex: tdx-cfg-block: add Verdin iMX8M Mini/Nano support"). Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>