From c57c7980ffe6e04a99b5f401a663426d7144f392 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 11 Aug 2005 17:56:56 +0200 Subject: Add NAND FLASH support for AMCC Bamboo 440EP eval board Patch by Stefan Roese, 11 Aug 2005 --- CHANGELOG | 3 + board/amcc/bamboo/bamboo.c | 122 ++++++++++++++++++++++++++++++++------- board/amcc/bamboo/flash.c | 11 +++- board/amcc/bamboo/init.S | 24 +++++--- cpu/ppc4xx/440gx_enet.c | 8 +-- include/configs/bamboo.h | 138 +++++++++++++++++++++++++++++++++++---------- 6 files changed, 242 insertions(+), 64 deletions(-) diff --git a/CHANGELOG b/CHANGELOG index beff987568..62d8a098fd 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,6 +2,9 @@ Changes for U-Boot 1.1.3: ====================================================================== +* Add NAND FLASH support for AMCC Bamboo 440EP eval board + Patch by Stefan Roese, 11 Aug 2005 + * Fix CompactFlash problem on HMI1001 board * Make new "mtdparts" code build with older compilers diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c index 0d5ab710d4..d02add5723 100644 --- a/board/amcc/bamboo/bamboo.c +++ b/board/amcc/bamboo/bamboo.c @@ -29,6 +29,7 @@ void ext_bus_cntlr_init(void); void configure_ppc440ep_pins(void); +int is_nand_selected(void); gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX]; #if 0 @@ -132,10 +133,10 @@ gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX]; EBC0_BNCR_BW_8BIT #define EBC0_BNCR_SMALL_FLASH_CS4 \ - EBC0_BNCR_BAS_ENCODE(0x87800000) | \ - EBC0_BNCR_BS_8MB | \ + EBC0_BNCR_BAS_ENCODE(0x87F00000) | \ + EBC0_BNCR_BS_1MB | \ EBC0_BNCR_BU_RW | \ - EBC0_BNCR_BW_16BIT + EBC0_BNCR_BW_8BIT /* Large Flash or SRAM */ #define EBC0_BNAP_LARGE_FLASH_OR_SRAM \ @@ -273,6 +274,87 @@ int board_early_init_f(void) return 0; } +#if (CONFIG_COMMANDS & CFG_CMD_NAND) +#include +extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE]; + +/*----------------------------------------------------------------------------+ + | nand_reset. + | Reset Nand flash + | This routine will abort previous cmd + +----------------------------------------------------------------------------*/ +int nand_reset(ulong addr) +{ + int wait=0, stat=0; + + out8(addr + NAND_CMD_REG, NAND0_CMD_RESET); + out8(addr + NAND_CMD_REG, NAND0_CMD_READ_STATUS); + + while ((stat != 0xc0) && (wait != 0xffff)) { + stat = in8(addr + NAND_DATA_REG); + wait++; + } + + if (stat == 0xc0) { + return 0; + } else { + printf("NAND Reset timeout.\n"); + return -1; + } +} + +void board_nand_set_device(int cs, ulong addr) +{ + /* Set NandFlash Core Configuration Register */ + out32(addr + NAND_CCR_REG, 0x00001000 | (cs << 24)); + + switch (cs) { + case 1: + /* ------- + * NAND0 + * ------- + * K9F1208U0A : 4 addr cyc, 1 col + 3 Row + * Set NDF1CR - Enable External CS1 in NAND FLASH controller + */ + out32(addr + NAND_CR1_REG, 0x80002222); + break; + + case 2: + /* ------- + * NAND1 + * ------- + * K9K2G0B : 5 addr cyc, 2 col + 3 Row + * Set NDF2CR : Enable External CS2 in NAND FLASH controller + */ + out32(addr + NAND_CR2_REG, 0xC0007777); + break; + } + + /* Perform Reset Command */ + if (nand_reset(addr) != 0) + return; +} + +void nand_init(void) +{ + board_nand_set_device(1, CFG_NAND_ADDR); + + nand_probe(CFG_NAND_ADDR); + if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) { + print_size(nand_dev_desc[0].totlen, "\n"); + } + +#if 0 /* NAND1 not supported yet */ + board_nand_set_device(2, CFG_NAND2_ADDR); + + nand_probe(CFG_NAND2_ADDR); + if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) { + print_size(nand_dev_desc[0].totlen, "\n"); + } +#endif +} +#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */ + int checkboard(void) { sys_info_t sysinfo; @@ -585,7 +667,11 @@ int is_powerpc440ep_pass1(void) +----------------------------------------------------------------------------*/ int is_nand_selected(void) { - return FALSE; /* test-only */ +#ifdef CONFIG_BAMBOO_NAND + return TRUE; +#else + return FALSE; +#endif } /*----------------------------------------------------------------------------+ @@ -829,12 +915,8 @@ void ext_bus_cntlr_init(void) /* NAND Flash */ ebc0_cs1_bnap_value = EBC0_BNAP_NAND_FLASH; ebc0_cs1_bncr_value = EBC0_BNCR_NAND_FLASH_CS1; - /*ebc0_cs2_bnap_value = EBC0_BNAP_NAND_FLASH; - ebc0_cs2_bncr_value = EBC0_BNCR_NAND_FLASH_CS2; - ebc0_cs3_bnap_value = EBC0_BNAP_NAND_FLASH; - ebc0_cs3_bncr_value = EBC0_BNCR_NAND_FLASH_CS3;*/ - ebc0_cs2_bnap_value = 0; - ebc0_cs2_bncr_value = 0; + ebc0_cs2_bnap_value = EBC0_BNAP_NAND_FLASH; + ebc0_cs2_bncr_value = EBC0_BNCR_NAND_FLASH_CS2; ebc0_cs3_bnap_value = 0; ebc0_cs3_bncr_value = 0; } else { @@ -985,7 +1067,7 @@ void ext_bus_cntlr_init(void) +----------------------------------------------------------------------------*/ uart_config_nb_t get_uart_configuration(void) { - return (L4); /* test-only */ + return (L4); } /*----------------------------------------------------------------------------+ @@ -1132,8 +1214,7 @@ void ndfc_selection_in_fpga(void) fpga_selection_1_reg = in8(FPGA_SELECTION_1_REG) &~FPGA_SEL_1_REG_NF_SELEC_MASK; fpga_selection_1_reg |= FPGA_SEL_1_REG_NF0_SEL_BY_NFCS1; - /*fpga_selection_1_reg |= FPGA_SEL_1_REG_NF1_SEL_BY_NFCS2; */ - /*fpga_selection_1_reg |= FPGA_SEL_1_REG_NF1_SEL_BY_NFCS3; */ + fpga_selection_1_reg |= FPGA_SEL_1_REG_NF1_SEL_BY_NFCS2; out8(FPGA_SELECTION_1_REG,fpga_selection_1_reg); } @@ -1725,11 +1806,15 @@ void force_bup_core_selection(core_selection_t *core_select_P, config_validity_t *(core_select_P+UIC_0_3) = CORE_SELECTED; *(core_select_P+UIC_4_9) = CORE_SELECTED; - *(core_select_P+SCP_CORE) = CORE_SELECTED; - *(core_select_P+DMA_CHANNEL_CD) = CORE_SELECTED; - *(core_select_P+PACKET_REJ_FUNC_AVAIL) = CORE_SELECTED; + *(core_select_P+SCP_CORE) = CORE_SELECTED; + *(core_select_P+DMA_CHANNEL_CD) = CORE_SELECTED; + *(core_select_P+PACKET_REJ_FUNC_AVAIL) = CORE_SELECTED; *(core_select_P+USB1_DEVICE) = CORE_SELECTED; + if (is_nand_selected()) { + *(core_select_P+NAND_FLASH) = CORE_SELECTED; + } + *config_val_P = CONFIG_IS_VALID; } @@ -1901,9 +1986,8 @@ void configure_ppc440ep_pins(void) SDR0_CUST0_NDFC_ENABLE | SDR0_CUST0_NDFC_BW_8_BIT | SDR0_CUST0_NDFC_ARE_MASK | - SDR0_CUST0_CHIPSELGAT_EN1 ); - /*SDR0_CUST0_CHIPSELGAT_EN2 ); */ - /*SDR0_CUST0_CHIPSELGAT_EN3 ); */ + SDR0_CUST0_CHIPSELGAT_EN1 | + SDR0_CUST0_CHIPSELGAT_EN2); ndfc_selection_in_fpga(); } diff --git a/board/amcc/bamboo/flash.c b/board/amcc/bamboo/flash.c index 97a4b988d5..a30ab7ada8 100644 --- a/board/amcc/bamboo/flash.c +++ b/board/amcc/bamboo/flash.c @@ -50,15 +50,16 @@ flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ /* * Mark big flash bank (16 bit instead of 8 bit access) in address with bit 0 */ -static unsigned long flash_addr_table[8][CFG_MAX_FLASH_BANKS] = { +static unsigned long flash_addr_table[][CFG_MAX_FLASH_BANKS] = { {0x87800001, 0xFFF00000, 0xFFF80000}, /* 0:boot from small flash */ {0x00000000, 0x00000000, 0x00000000}, /* 1:boot from pci 66 */ {0x00000000, 0x00000000, 0x00000000}, /* 2:boot from nand flash */ - {0x87800000, 0x87880000, 0xFF800001}, /* 3:boot from big flash 33*/ - {0x87800000, 0x87880000, 0xFF800001}, /* 4:boot from big flash 66*/ + {0x87F00000, 0x87F80000, 0xFFC00001}, /* 3:boot from big flash 33*/ + {0x87F00000, 0x87F80000, 0xFFC00001}, /* 4:boot from big flash 66*/ {0x00000000, 0x00000000, 0x00000000}, /* 5:boot from */ {0x00000000, 0x00000000, 0x00000000}, /* 6:boot from pci 66 */ {0x00000000, 0x00000000, 0x00000000}, /* 7:boot from */ + {0x87C00001, 0xFFF00000, 0xFFF80000}, /* 0:boot from small flash */ }; /* @@ -117,6 +118,10 @@ unsigned long flash_init(void) index = 2; break; } + } else if (index == 0) { + if (in8(FPGA_SETTING_REG) & FPGA_SET_REG_OP_CODE_FLASH_ABOVE) { + index = 8; /* sram below op code flash -> new index 8 */ + } } DEBUGF("\n"); diff --git a/board/amcc/bamboo/init.S b/board/amcc/bamboo/init.S index 907029345b..7820107aa5 100644 --- a/board/amcc/bamboo/init.S +++ b/board/amcc/bamboo/init.S @@ -86,14 +86,20 @@ tlbtab: tlbtab_start - /* - 0xf0000000 must be first, before relocation SA_I must be off to use the - dcache as stack. It is patched after relocation to enable SA_I - */ - tlbentry( 0xf0000000, SZ_256M, 0xf0000000, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/) - tlbentry( CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I ) - tlbentry( CFG_PCI_BASE, SZ_256M, 0xE0000000, 0, AC_R|AC_W|SA_G|SA_I ) - tlbentry( CFG_NVRAM_BASE_ADDR, SZ_256M, 0x80000000, 0, AC_R|AC_W|AC_X|SA_W|SA_I ) + + /* + * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the + * speed up boot process. It is patched after relocation to enable SA_I + */ + tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/) + + /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ + tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G ) + + tlbentry( CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I ) + tlbentry( CFG_PCI_BASE, SZ_256M, CFG_PCI_BASE, 0, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_NVRAM_BASE_ADDR, SZ_256M, CFG_NVRAM_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_W|SA_I ) + tlbentry( CFG_NAND_ADDR, SZ_256M, CFG_NAND_ADDR, 0, AC_R|AC_W|AC_X|SA_W|SA_I ) /* PCI */ tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 0, AC_R|AC_W|SA_G|SA_I ) @@ -102,6 +108,6 @@ tlbtab: tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 0, AC_R|AC_W|SA_G|SA_I ) /* USB 2.0 Device */ - tlbentry( CFG_USB_DEVICE, SZ_1K, 0x50000000, 0, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_USB_DEVICE, SZ_1K, CFG_USB_DEVICE, 0, AC_R|AC_W|SA_G|SA_I ) tlbtab_end diff --git a/cpu/ppc4xx/440gx_enet.c b/cpu/ppc4xx/440gx_enet.c index 63227fa153..68cbf34391 100644 --- a/cpu/ppc4xx/440gx_enet.c +++ b/cpu/ppc4xx/440gx_enet.c @@ -375,8 +375,8 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis) out32 (RGMII_FER, ((RGMII_FER_RGMII << RGMII_FER_V (2)) | (RGMII_FER_RGMII << RGMII_FER_V (3)))); } - #endif + out32 (ZMII_SSR, ZMII_SSR_SP << ZMII_SSR_V(devnum)); __asm__ volatile ("eieio"); @@ -521,13 +521,13 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis) } mtsdr(sdr_mfr, reg); #endif + /* Set ZMII/RGMII speed according to the phy link speed */ reg = in32 (ZMII_SSR); if ( (speed == 100) || (speed == 1000) ) out32 (ZMII_SSR, reg | (ZMII_SSR_SP << ZMII_SSR_V (devnum))); else - out32 (ZMII_SSR, - reg & (~(ZMII_SSR_SP << ZMII_SSR_V (devnum)))); + out32 (ZMII_SSR, reg & (~(ZMII_SSR_SP << ZMII_SSR_V (devnum)))); if ((devnum == 2) || (devnum == 3)) { if (speed == 1000) @@ -672,7 +672,7 @@ static int ppc_440x_eth_init (struct eth_device *dev, bd_t * bis) /* set RX buffer size */ mtdcr (malrcbs3, ENET_MAX_MTU_ALIGNED / 16); break; -#endif /*CONFIG_440GX */ +#endif /* CONFIG_440GX */ case 0: default: /* setup MAL tx & rx channel pointers */ diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index 88bbadfc29..64ea6bef91 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -32,11 +32,18 @@ *----------------------------------------------------------------------*/ #define CONFIG_BAMBOO 1 /* Board is BAMBOO */ #define CONFIG_440EP 1 /* Specific PPC440EP support */ - #define CONFIG_4xx 1 /* ... PPC4xx family */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ + +/* + * Please note that, if NAND support is enabled, the 2nd ethernet port + * can't be used because of pin multiplexing. So, if you want to use the + * 2nd ethernet port you have to "undef" the following define. + */ +#define CONFIG_BAMBOO_NAND 1 /* enable nand flash support */ + /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) @@ -58,13 +65,15 @@ #define CFG_USB_DEVICE 0x50000000 #define CFG_NVRAM_BASE_ADDR 0x80000000 -#define CFG_BCSR_BASE (CFG_NVRAM_BASE_ADDR | 0x2000) +#define CFG_BOOT_BASE_ADDR 0xf0000000 +#define CFG_NAND_ADDR 0x90000000 +#define CFG_NAND2_ADDR 0x94000000 /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ -#define CFG_INIT_RAM_ADDR 0xf0000000 /* DCache */ -#define CFG_INIT_RAM_END 0x1000 +#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ +#define CFG_INIT_RAM_END (8 << 10) #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET @@ -88,7 +97,7 @@ * The DS1558 code assumes this condition * *----------------------------------------------------------------------*/ -#define CFG_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */ +#define CFG_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */ #define CONFIG_RTC_DS1556 1 /* DS1556 RTC */ /*----------------------------------------------------------------------- @@ -118,21 +127,80 @@ #define CFG_FLASH_ADDR1 0x2aa #define CFG_FLASH_WORD_SIZE unsigned char -#define CFG_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */ -#define CFG_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */ +#define CFG_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */ +#define CFG_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */ #ifdef CFG_ENV_IS_IN_FLASH #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ -#if 0 /* test-only */ /* Address and size of Redundant Environment Sector */ #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) -#endif #endif /* CFG_ENV_IS_IN_FLASH */ +/*----------------------------------------------------------------------- + * NAND-FLASH related + *----------------------------------------------------------------------*/ +#define NAND_CMD_REG (0x00) /* NandFlash Command Register */ +#define NAND_ADDR_REG (0x04) /* NandFlash Address Register */ +#define NAND_DATA_REG (0x08) /* NandFlash Data Register */ +#define NAND_ECC0_REG (0x10) /* NandFlash ECC Register0 */ +#define NAND_ECC1_REG (0x14) /* NandFlash ECC Register1 */ +#define NAND_ECC2_REG (0x18) /* NandFlash ECC Register2 */ +#define NAND_ECC3_REG (0x1C) /* NandFlash ECC Register3 */ +#define NAND_ECC4_REG (0x20) /* NandFlash ECC Register4 */ +#define NAND_ECC5_REG (0x24) /* NandFlash ECC Register5 */ +#define NAND_ECC6_REG (0x28) /* NandFlash ECC Register6 */ +#define NAND_ECC7_REG (0x2C) /* NandFlash ECC Register7 */ +#define NAND_CR0_REG (0x30) /* NandFlash Device Bank0 Config Register */ +#define NAND_CR1_REG (0x34) /* NandFlash Device Bank1 Config Register */ +#define NAND_CR2_REG (0x38) /* NandFlash Device Bank2 Config Register */ +#define NAND_CR3_REG (0x3C) /* NandFlash Device Bank3 Config Register */ +#define NAND_CCR_REG (0x40) /* NandFlash Core Configuration Register */ +#define NAND_STAT_REG (0x44) /* NandFlash Device Status Register */ +#define NAND_HWCTL_REG (0x48) /* NandFlash Direct Hwd Control Register */ +#define NAND_REVID_REG (0x50) /* NandFlash Core Revision Id Register */ + +/* Nand Flash K9F1208U0A Command Set => Nand Flash 0 */ +#define NAND0_CMD_READ1_HALF1 0x00 /* Starting addr for 1rst half of registers */ +#define NAND0_CMD_READ1_HALF2 0x01 /* Starting addr for 2nd half of registers */ +#define NAND0_CMD_READ2 0x50 +#define NAND0_CMD_READ_ID 0x90 +#define NAND0_CMD_READ_STATUS 0x70 +#define NAND0_CMD_RESET 0xFF +#define NAND0_CMD_PAGE_PROG 0x80 +#define NAND0_CMD_PAGE_PROG_TRUE 0x10 +#define NAND0_CMD_PAGE_PROG_DUMMY 0x11 +#define NAND0_CMD_BLOCK_ERASE 0x60 +#define NAND0_CMD_BLOCK_ERASE_END 0xD0 + +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define SECTORSIZE 512 + +#define ADDR_COLUMN 1 +#define ADDR_PAGE 2 +#define ADDR_COLUMN_PAGE 3 + +#define NAND_ChipID_UNKNOWN 0x00 +#define NAND_MAX_FLOORS 1 +#define NAND_MAX_CHIPS 1 + +#define WRITE_NAND_COMMAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_CMD_REG) = d;} while(0) +#define WRITE_NAND_ADDRESS(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_ADDR_REG) = d;} while(0) +#define WRITE_NAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_DATA_REG) = d;} while(0) +#define READ_NAND(adr) (*(volatile u8 *)((ulong)adr+NAND_DATA_REG)) +#define NAND_WAIT_READY(nand) while (!(*(volatile u8 *)((ulong)nand->IO_ADDR+NAND_STAT_REG) & 0x01)) + +/* not needed with 440EP NAND controller */ +#define NAND_CTL_CLRALE(nandptr) +#define NAND_CTL_SETALE(nandptr) +#define NAND_CTL_CLRCLE(nandptr) +#define NAND_CTL_SETCLE(nandptr) +#define NAND_DISABLE_CE(nand) +#define NAND_ENABLE_CE(nand) + /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------------- */ @@ -206,10 +274,14 @@ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_NET_MULTI 1 /* required for netconsole */ #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ + +#ifndef CONFIG_BAMBOO_NAND +#define CONFIG_NET_MULTI 1 /* required for netconsole */ #define CONFIG_PHY1_ADDR 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ +#endif /* CONFIG_BAMBOO_NAND */ + #define CONFIG_NO_PHY_RESET 1 /* no PHY reset on bamboo!!! */ #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ @@ -228,8 +300,15 @@ #define USB_2_0_DEVICE #endif /*CONFIG_440EP*/ +#ifdef CONFIG_BAMBOO_NAND +#define _CFG_CMD_NAND CFG_CMD_NAND +#else +#define _CFG_CMD_NAND 0 +#endif /* CONFIG_BAMBOO_NAND */ + #define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ CFG_CMD_ASKENV | \ + CFG_CMD_EEPROM | \ CFG_CMD_DATE | \ CFG_CMD_DHCP | \ CFG_CMD_DIAG | \ @@ -244,6 +323,7 @@ CFG_CMD_REGINFO | \ CFG_CMD_SDRAM | \ CFG_CMD_USB | \ + _CFG_CMD_NAND | \ CFG_CMD_SNTP ) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ @@ -253,42 +333,42 @@ * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CONFIG_LYNXKDI 1 /* support kdi files */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_LYNXKDI 1 /* support kdi files */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ /* General PCI */ -#define CONFIG_PCI /* include pci support */ -#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ +#define CONFIG_PCI /* include pci support */ +#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/ /* Board-specific PCI */ #define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ #define CFG_PCI_TARGET_INIT #define CFG_PCI_MASTER_INIT -#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ -#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ +#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ /* * For booting Linux, the board info and command line data @@ -300,7 +380,7 @@ /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 /* For IBM 440 CPUs */ +#define CFG_DCACHE_SIZE (32<<10) /* For IBM 440 CPUs */ #define CFG_CACHELINE_SIZE 32 /* ... */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -- cgit v1.2.3 From 9e00589bdd0b3f6336e1e6bb98a342a2fa1ef863 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 11 Aug 2005 17:58:40 +0200 Subject: Changed AMCC Bubinga (405EP) configuration to support 2nd eth port Patch by Stefan Roese, 11 Aug 2005 --- CHANGELOG | 3 +++ include/configs/bubinga.h | 6 ++++-- 2 files changed, 7 insertions(+), 2 deletions(-) diff --git a/CHANGELOG b/CHANGELOG index 62d8a098fd..c87780c6a8 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,6 +2,9 @@ Changes for U-Boot 1.1.3: ====================================================================== +* Changed AMCC Bubinga (405EP) configuration to support 2nd eth port + Patch by Stefan Roese, 11 Aug 2005 + * Add NAND FLASH support for AMCC Bamboo 440EP eval board Patch by Stefan Roese, 11 Aug 2005 diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h index c7451959a8..bc5aaf8934 100644 --- a/include/configs/bubinga.h +++ b/include/configs/bubinga.h @@ -127,6 +127,10 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address */ +#define CONFIG_HAS_ETH1 +#define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */ +#define CONFIG_NET_MULTI 1 +#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Bubinga */ @@ -199,8 +203,6 @@ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ - /*----------------------------------------------------------------------- * I2C stuff *----------------------------------------------------------------------- -- cgit v1.2.3 From 84286386a891633aae770bff24189c16a2546ed0 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 11 Aug 2005 18:03:14 +0200 Subject: Update AMCC Yosemite to get a consistent setup for all AMCC eval boards (baudrate, environment...). Flash driver fixed. Patch by Stefan Roese, 11 Aug 2005 --- CHANGELOG | 4 + board/amcc/yosemite/Makefile | 1 - board/amcc/yosemite/flash.c | 571 ----------------------------------------- board/amcc/yosemite/init.S | 21 +- board/amcc/yosemite/yosemite.c | 55 +++- include/configs/yosemite.h | 272 ++++++++++---------- 6 files changed, 208 insertions(+), 716 deletions(-) delete mode 100644 board/amcc/yosemite/flash.c diff --git a/CHANGELOG b/CHANGELOG index c87780c6a8..f0c1eed8c7 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,6 +2,10 @@ Changes for U-Boot 1.1.3: ====================================================================== +* Update AMCC Yosemite to get a consistent setup for all AMCC eval + boards (baudrate, environment...). Flash driver fixed. + Patch by Stefan Roese, 11 Aug 2005 + * Changed AMCC Bubinga (405EP) configuration to support 2nd eth port Patch by Stefan Roese, 11 Aug 2005 diff --git a/board/amcc/yosemite/Makefile b/board/amcc/yosemite/Makefile index 5654f91a83..47116d3674 100644 --- a/board/amcc/yosemite/Makefile +++ b/board/amcc/yosemite/Makefile @@ -26,7 +26,6 @@ include $(TOPDIR)/config.mk LIB = lib$(BOARD).a OBJS = $(BOARD).o -OBJS += flash.o SOBJS = init.o $(LIB): $(OBJS) $(SOBJS) diff --git a/board/amcc/yosemite/flash.c b/board/amcc/yosemite/flash.c deleted file mode 100644 index cd6a2e61e6..0000000000 --- a/board/amcc/yosemite/flash.c +++ /dev/null @@ -1,571 +0,0 @@ -/* - * (C) Copyright 2002-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2002 Jun Gu - * Add support for Am29F016D and dynamic switch setting. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * Modified 4/5/2001 - * Wait for completion of each sector erase command issued - * 4/5/2001 - * Chris Hallinan - DS4.COM, Inc. - clh@net1plus.com - */ - -/* - * Ported to XPedite1000, 1/2 mb boot flash only - * Travis B. Sawyer, - */ - -#include -#include -#include - -#undef DEBUG -#ifdef DEBUG -#define DEBUGF(x...) printf(x) -#else -#define DEBUGF(x...) -#endif /* DEBUG */ - -#define BOOT_SMALL_FLASH 32 /* 00100000 */ -#define FLASH_ONBD_N 2 /* 00000010 */ -#define FLASH_SRAM_SEL 1 /* 00000001 */ - -#define BOOT_SMALL_FLASH_VAL 4 -#define FLASH_ONBD_N_VAL 2 -#define FLASH_SRAM_SEL_VAL 1 - -flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ - -unsigned long flash_addr_table[512][CFG_MAX_FLASH_BANKS] = { - {0xfe000000} - -}; - -/*----------------------------------------------------------------------- - * Functions - */ -static ulong flash_get_size(vu_long * addr, flash_info_t * info); -static int write_word(flash_info_t * info, ulong dest, ulong data); - -#define ADDR0 0xaaaa -#define ADDR1 0x5554 -#define FLASH_WORD_SIZE unsigned short - -/*----------------------------------------------------------------------- - */ - -unsigned long flash_init(void) -{ - unsigned long total_b = 0; - unsigned long size_b[CFG_MAX_FLASH_BANKS]; - unsigned short index = 0; - int i; - - DEBUGF("\n"); - DEBUGF("FLASH: Index: %d\n", index); - - /* Init: no FLASHes known */ - for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) { - flash_info[i].flash_id = FLASH_UNKNOWN; - flash_info[i].sector_count = -1; - flash_info[i].size = 0; - - /* check whether the address is 0 */ - if (flash_addr_table[index][i] == 0) { - continue; - } - - /* call flash_get_size() to initialize sector address */ - size_b[i] = flash_get_size((vu_long *) - flash_addr_table[index][i], - &flash_info[i]); - flash_info[i].size = size_b[i]; - if (flash_info[i].flash_id == FLASH_UNKNOWN) { - printf - ("## Unknown FLASH on Bank %d - Size = 0x%08lx = %ld MB\n", - i, size_b[i], size_b[i] << 20); - flash_info[i].sector_count = -1; - flash_info[i].size = 0; - } - - total_b += flash_info[i].size; - } - - /* FLASH protect Monitor */ - flash_protect(FLAG_PROTECT_SET, - CFG_MONITOR_BASE, 0xFFFFFFFF, &flash_info[0]); - - return total_b; -} - -/*----------------------------------------------------------------------- - */ -void flash_print_info(flash_info_t * info) -{ - int i; - int k; - int size; - int erased; - volatile unsigned long *flash; - - if (info->flash_id == FLASH_UNKNOWN) { - printf("missing or unknown FLASH type\n"); - return; - } - - switch (info->flash_id & FLASH_VENDMASK) { - case FLASH_MAN_AMD: - printf("AMD "); - break; - case FLASH_MAN_FUJ: - printf("FUJITSU "); - break; - case FLASH_MAN_SST: - printf("SST "); - break; - default: - printf("Unknown Vendor "); - break; - } - - switch (info->flash_id & FLASH_TYPEMASK) { - case FLASH_AMD016: - printf("AM29F016D (16 Mbit, uniform sector size)\n"); - break; - case FLASH_AM040: - printf("AM29F040 (512 Kbit, uniform sector size)\n"); - break; - case FLASH_AM400B: - printf("AM29LV400B (4 Mbit, bottom boot sect)\n"); - break; - case FLASH_AM400T: - printf("AM29LV400T (4 Mbit, top boot sector)\n"); - break; - case FLASH_AM800B: - printf("AM29LV800B (8 Mbit, bottom boot sect)\n"); - break; - case FLASH_AM800T: - printf("AM29LV800T (8 Mbit, top boot sector)\n"); - break; - case FLASH_AM160B: - printf("AM29LV160B (16 Mbit, bottom boot sect)\n"); - break; - case FLASH_AM160T: - printf("AM29LV160T (16 Mbit, top boot sector)\n"); - break; - case FLASH_AM320B: - printf("AM29LV320B (32 Mbit, bottom boot sect)\n"); - break; - case FLASH_AM320T: - printf("AM29LV320T (32 Mbit, top boot sector)\n"); - break; - case FLASH_SST800A: - printf("SST39LF/VF800 (8 Mbit, uniform sector size)\n"); - break; - case FLASH_SST160A: - printf("SST39LF/VF160 (16 Mbit, uniform sector size)\n"); - break; - default: - printf("Unknown Chip Type\n"); - break; - } - - printf(" Size: %ld KB in %d Sectors\n", - info->size >> 10, info->sector_count); - - printf(" Sector Start Addresses:"); - for (i = 0; i < info->sector_count; ++i) { - /* - * Check if whole sector is erased - */ - if (i != (info->sector_count - 1)) - size = info->start[i + 1] - info->start[i]; - else - size = info->start[0] + info->size - info->start[i]; - erased = 1; - flash = (volatile unsigned long *)info->start[i]; - size = size >> 2; /* divide by 4 for longword access */ - for (k = 0; k < size; k++) { - if (*flash++ != 0xffffffff) { - erased = 0; - break; - } - } - - if ((i % 5) == 0) - printf("\n "); - printf(" %08lX%s%s", - info->start[i], - erased ? " E" : " ", info->protect[i] ? "RO " : " "); - } - printf("\n"); - return; -} - -/*----------------------------------------------------------------------- - */ - -/*----------------------------------------------------------------------- - */ - -/* - * The following code cannot be run from FLASH! - */ -static ulong flash_get_size(vu_long * addr, flash_info_t * info) -{ - short i; - FLASH_WORD_SIZE value; - ulong base = (ulong) addr; - volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *) addr; - - DEBUGF("FLASH ADDR: %08x\n", (unsigned)addr); - - /* Write auto select command: read Manufacturer ID */ - udelay(10000); - *(FLASH_WORD_SIZE *) ((int)addr + ADDR0) = (FLASH_WORD_SIZE) 0x00AA; - udelay(1000); - *(FLASH_WORD_SIZE *) ((int)addr + ADDR1) = (FLASH_WORD_SIZE) 0x0055; - udelay(1000); - *(FLASH_WORD_SIZE *) ((int)addr + ADDR0) = (FLASH_WORD_SIZE) 0x0090; - udelay(1000); - - value = addr2[0]; - - DEBUGF("FLASH MANUFACT: %x\n", value); - - switch (value) { - case (FLASH_WORD_SIZE) AMD_MANUFACT: - info->flash_id = FLASH_MAN_AMD; - break; - case (FLASH_WORD_SIZE) FUJ_MANUFACT: - info->flash_id = FLASH_MAN_FUJ; - break; - case (FLASH_WORD_SIZE) SST_MANUFACT: - info->flash_id = FLASH_MAN_SST; - break; - case (FLASH_WORD_SIZE) STM_MANUFACT: - info->flash_id = FLASH_MAN_STM; - break; - default: - info->flash_id = FLASH_UNKNOWN; - info->sector_count = 0; - info->size = 0; - return (0); /* no or unknown flash */ - } - -#ifdef CONFIG_ADCIOP - value = addr2[0]; /* device ID */ - debug("\ndev_code=%x\n", value); -#else - value = addr2[1]; /* device ID */ -#endif - - DEBUGF("\nFLASH DEVICEID: %x\n", value); - - info->flash_id = 0; - info->sector_count = CFG_MAX_FLASH_SECT; - info->size = 0x02000000; - - /* set up sector start address table */ - for (i = 0; i < info->sector_count; i++) { - info->start[i] = (int)base + (i * 0x00020000); - info->protect[i] = 0; - } - - *(FLASH_WORD_SIZE *) ((int)addr) = (FLASH_WORD_SIZE) 0x00F0; /* reset bank */ - - return (info->size); -} - -int wait_for_DQ7(flash_info_t * info, int sect) -{ - ulong start, now, last; - volatile FLASH_WORD_SIZE *addr = - (FLASH_WORD_SIZE *) (info->start[sect]); - - start = get_timer(0); - last = start; - while ((addr[0] & (FLASH_WORD_SIZE) 0x00800080) != - (FLASH_WORD_SIZE) 0x00800080) { - if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) { - printf("Timeout\n"); - return -1; - } - /* show that we're waiting */ - if ((now - last) > 1000) { /* every second */ - putc('.'); - last = now; - } - } - return 0; -} - -/*----------------------------------------------------------------------- - */ - -int flash_erase(flash_info_t * info, int s_first, int s_last) -{ - volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *) (info->start[0]); - volatile FLASH_WORD_SIZE *addr2; - int flag, prot, sect, l_sect; - - if ((s_first < 0) || (s_first > s_last)) { - if (info->flash_id == FLASH_UNKNOWN) { - printf("- missing\n"); - } else { - printf("- no sectors to erase\n"); - } - return 1; - } - - if (info->flash_id == FLASH_UNKNOWN) { - printf("Can't erase unknown flash type - aborted\n"); - return 1; - } - - prot = 0; - for (sect = s_first; sect <= s_last; ++sect) { - if (info->protect[sect]) { - prot++; - } - } - - if (prot) { - printf("- Warning: %d protected sectors will not be erased!\n", - prot); - } else { - printf("\n"); - } - - l_sect = -1; - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - - /* Start erase on unprotected sectors */ - for (sect = s_first; sect <= s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - addr2 = (FLASH_WORD_SIZE *) (info->start[sect]); - printf("Erasing sector %p\n", addr2); - *(FLASH_WORD_SIZE *) ((int)addr + ADDR0) = - (FLASH_WORD_SIZE) 0x00AA; - asm("sync"); - asm("isync"); - *(FLASH_WORD_SIZE *) ((int)addr + ADDR1) = - (FLASH_WORD_SIZE) 0x0055; - asm("sync"); - asm("isync"); - *(FLASH_WORD_SIZE *) ((int)addr + ADDR0) = - (FLASH_WORD_SIZE) 0x0080; - asm("sync"); - asm("isync"); - *(FLASH_WORD_SIZE *) ((int)addr + ADDR0) = - (FLASH_WORD_SIZE) 0x00AA; - asm("sync"); - asm("isync"); - *(FLASH_WORD_SIZE *) ((int)addr + ADDR1) = - (FLASH_WORD_SIZE) 0x0055; - asm("sync"); - asm("isync"); - addr2[0] = (FLASH_WORD_SIZE) 0x00300030; /* sector erase */ - asm("sync"); - asm("isync"); - - l_sect = sect; - /* - * Wait for each sector to complete, it's more - * reliable. According to AMD Spec, you must - * issue all erase commands within a specified - * timeout. This has been seen to fail, especially - * if printf()s are included (for debug)!! - */ - wait_for_DQ7(info, sect); - } - } - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - /* wait at least 80us - let's wait 1 ms */ - udelay(1000); - -#if 0 - /* - * We wait for the last triggered sector - */ - if (l_sect < 0) - goto DONE; - wait_for_DQ7(info, l_sect); - - DONE: -#endif - /* reset to read mode */ - addr = (FLASH_WORD_SIZE *) info->start[0]; - addr[0] = (FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */ - - printf(" done\n"); - return 0; -} - -/*----------------------------------------------------------------------- - * Copy memory to flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ -int write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt) -{ - ulong cp, wp, data; - int i, l, rc; - ulong status_value = 0; - - wp = (addr & ~3); /* get lower word aligned address */ - - /* - * handle unaligned start bytes - */ - if ((l = addr - wp) != 0) { - data = 0; - for (i = 0, cp = wp; i < l; ++i, ++cp) { - data = (data << 8) | (*(uchar *) cp); - } - for (; i < 4 && cnt > 0; ++i) { - data = (data << 8) | *src++; - --cnt; - ++cp; - } - for (; cnt == 0 && i < 4; ++i, ++cp) { - data = (data << 8) | (*(uchar *) cp); - } - - if ((rc = write_word(info, wp, data)) != 0) { - return (rc); - } - wp += 4; - } - - /* - * handle word aligned part - */ - while (cnt >= 4) { - - /*print status if needed */ - if ((wp >= (status_value + 0x20000)) - && (status_value < 0xFFFE0000)) { - status_value = wp; - printf("writing to sector 0x%X\n", status_value); - } - - data = 0; - for (i = 0; i < 4; ++i) { - data = (data << 8) | *src++; - } - if ((rc = write_word(info, wp, data)) != 0) { - return (rc); - } - wp += 4; - cnt -= 4; - } - - if (cnt == 0) { - return (0); - } - - /* - * handle unaligned tail bytes - */ - data = 0; - for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) { - data = (data << 8) | *src++; - --cnt; - } - for (; i < 4; ++i, ++cp) { - data = (data << 8) | (*(uchar *) cp); - } - - return (write_word(info, wp, data)); -} - -/*----------------------------------------------------------------------- - * Write a word to Flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ -static int write_word(flash_info_t * info, ulong dest, ulong data) -{ - vu_long *addr2 = (vu_long *) (info->start[0]); - volatile FLASH_WORD_SIZE *dest2 = (FLASH_WORD_SIZE *) dest; - volatile FLASH_WORD_SIZE *data2 = (FLASH_WORD_SIZE *) & data; - ulong start; - int i; - - /* Check if Flash is (sufficiently) erased */ - if ((*((volatile FLASH_WORD_SIZE *)dest) & - (FLASH_WORD_SIZE) data) != (FLASH_WORD_SIZE) data) { - return (2); - } - - for (i = 0; i < 4 / sizeof(FLASH_WORD_SIZE); i++) { - int flag; - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - - *(FLASH_WORD_SIZE *) ((int)addr2 + ADDR0) = - (FLASH_WORD_SIZE) 0x00AA; - asm("sync"); - asm("isync"); - *(FLASH_WORD_SIZE *) ((int)addr2 + ADDR1) = - (FLASH_WORD_SIZE) 0x0055; - asm("sync"); - asm("isync"); - *(FLASH_WORD_SIZE *) ((int)addr2 + ADDR0) = - (FLASH_WORD_SIZE) 0x00A0; - asm("sync"); - asm("isync"); - - dest2[i] = data2[i]; - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - /* data polling for D7 */ - start = get_timer(0); - while ((dest2[i] & (FLASH_WORD_SIZE) 0x00800080) != - (data2[i] & (FLASH_WORD_SIZE) 0x00800080)) { - - if (get_timer(start) > CFG_FLASH_WRITE_TOUT) { - return (1); - } - } - } - - return (0); -} - -/*----------------------------------------------------------------------- - */ diff --git a/board/amcc/yosemite/init.S b/board/amcc/yosemite/init.S index 7ba43c7b06..425ad0868f 100644 --- a/board/amcc/yosemite/init.S +++ b/board/amcc/yosemite/init.S @@ -86,14 +86,19 @@ tlbtab: tlbtab_start - /* - 0xf0000000 must be first, before relocation SA_I must be off to use the - dcache as stack. It is patched after relocation to enable SA_I - */ - tlbentry( 0xf0000000, SZ_256M, 0xf0000000, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/) - tlbentry( CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I ) - tlbentry( CFG_PCI_BASE, SZ_256M, 0xE0000000, 0, AC_R|AC_W|SA_G|SA_I ) - tlbentry( CFG_NVRAM_BASE_ADDR, SZ_16K, 0x80000000, 0, AC_R|AC_W|AC_X|SA_W|SA_I ) + + /* + * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the + * speed up boot process. It is patched after relocation to enable SA_I + */ + tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_G/*|SA_I*/) + + /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ + tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G ) + + tlbentry( CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I ) + tlbentry( CFG_PCI_BASE, SZ_256M, CFG_PCI_BASE, 0, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_NVRAM_BASE_ADDR, SZ_256M, CFG_NVRAM_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_W|SA_I ) /* PCI */ tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 0, AC_R|AC_W|SA_G|SA_I ) diff --git a/board/amcc/yosemite/yosemite.c b/board/amcc/yosemite/yosemite.c index 6c8a883e18..b50e99ab8d 100644 --- a/board/amcc/yosemite/yosemite.c +++ b/board/amcc/yosemite/yosemite.c @@ -20,9 +20,12 @@ */ #include +#include #include #include +extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ + int board_early_init_f(void) { register uint reg; @@ -35,7 +38,7 @@ int board_early_init_f(void) mtdcr(ebccfgd, reg | 0x04000000); /* Set ATC */ mtebc(pb0ap, 0x03017300); /* FLASH/SRAM */ - mtebc(pb0cr, 0xfe0ba000); /* BAS=0xfe0 32MB r/w 16-bit */ + mtebc(pb0cr, 0xfc0da000); /* BAS=0xfc0 64MB r/w 16-bit */ mtebc(pb1ap, 0x00000000); mtebc(pb1cr, 0x00000000); @@ -122,6 +125,54 @@ int board_early_init_f(void) return 0; } +int misc_init_r (void) +{ + DECLARE_GLOBAL_DATA_PTR; + uint pbcr; + int size_val = 0; + + /* Re-do sizing to get full correct info */ + mtdcr(ebccfga, pb0cr); + pbcr = mfdcr(ebccfgd); + switch (gd->bd->bi_flashsize) { + case 1 << 20: + size_val = 0; + break; + case 2 << 20: + size_val = 1; + break; + case 4 << 20: + size_val = 2; + break; + case 8 << 20: + size_val = 3; + break; + case 16 << 20: + size_val = 4; + break; + case 32 << 20: + size_val = 5; + break; + case 64 << 20: + size_val = 6; + break; + case 128 << 20: + size_val = 7; + break; + } + pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17); + mtdcr(ebccfga, pb0cr); + mtdcr(ebccfgd, pbcr); + + /* Monitor protection ON by default */ + (void)flash_protect(FLAG_PROTECT_SET, + -CFG_MONITOR_LEN, + 0xffffffff, + &flash_info[0]); + + return 0; +} + int checkboard(void) { sys_info_t sysinfo; @@ -135,6 +186,8 @@ int checkboard(void) printf("\tOPB: %lu MHz\n", sysinfo.freqOPB / 1000000); printf("\tPER: %lu MHz\n", sysinfo.freqEPB / 1000000); printf("\tPCI: %lu MHz\n", sysinfo.freqPCI / 1000000); + + return (0); } diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index ddc9169858..4ac930b42a 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -1,4 +1,6 @@ /* + * (C) Copyright 2005 + * Stefan Roese, DENX Software Engineering, sr@denx.de. * * See file CREDITS for list of people who contributed to this * project. @@ -28,56 +30,53 @@ /*----------------------------------------------------------------------- * High Level Configuration Options *----------------------------------------------------------------------*/ -#define CONFIG_YOSEMITE 1 /* Board is BAMBOO */ -#define CONFIG_440EP 1 /* Specific PPC440EP support */ - -#define CONFIG_4xx 1 /* ... PPC4xx family */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#undef CFG_DRAM_TEST /* disable - takes long time! */ +#define CONFIG_YOSEMITE 1 /* Board is Yosemite */ +#define CONFIG_440EP 1 /* Specific PPC440EP support */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ + /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CFG_FLASH_BASE 0xfe000000 /* start of FLASH */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ -#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory */ -#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 -#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 -#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 - +#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ +#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ +#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ +#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ +#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 +#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 +#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 /*Don't change either of these*/ -#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ -#define CFG_PCI_BASE 0xe0000000 /* internal PCI regs */ +#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals*/ +#define CFG_PCI_BASE 0xe0000000 /* internal PCI regs*/ /*Don't change either of these*/ -#define CFG_USB_DEVICE 0x50000000 -#define CFG_NVRAM_BASE_ADDR 0x80000000 -#define CFG_BCSR_BASE (CFG_NVRAM_BASE_ADDR | 0x2000) +#define CFG_USB_DEVICE 0x50000000 +#define CFG_NVRAM_BASE_ADDR 0x80000000 +#define CFG_BCSR_BASE (CFG_NVRAM_BASE_ADDR | 0x2000) +#define CFG_BOOT_BASE_ADDR 0xf0000000 /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ -#define CFG_INIT_RAM_ADDR 0xf0000000 /* DCache */ -#define CFG_INIT_RAM_END 0x2000 -#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ +#define CFG_INIT_RAM_END (8 << 10) +#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ -#define CFG_KBYTES_SDRAM ( 128 * 1024) /* 128MB */ -#define CFG_SDRAM_BANKS (2) /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ -#define CONFIG_BAUDRATE 9600 -#define CONFIG_SERIAL_MULTI 1 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI 1 /*define this if you want console on UART1*/ #undef CONFIG_UART1_CONSOLE @@ -85,26 +84,21 @@ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- - * NVRAM/RTC - * - * NOTE: The RTC registers are located at 0x7FFF0 - 0x7FFFF - * The DS1558 code assumes this condition - * + * Environment *----------------------------------------------------------------------*/ -#define CFG_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */ -#define CONFIG_RTC_DS1556 1 /* DS1556 RTC */ +/* + * Define here the location of the environment variables (FLASH or EEPROM). + * Note: DENX encourages to use redundant environment in FLASH. + */ +#if 1 +#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#else +#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#endif /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#if 1 /* test-only */ -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 256 /* sectors per device */ - -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 120000 /* Timeout for Flash Write (in ms) */ -#else #define CFG_FLASH_CFI /* The flash is CFI compatible */ #define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CFG_FLASH_CFI_AMD_RESET 1 /* AMD RESET for STM 29W320DB! */ @@ -116,12 +110,24 @@ #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#endif + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#endif /* CFG_ENV_IS_IN_FLASH */ /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ #undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */ +#define CFG_KBYTES_SDRAM (128 * 1024) /* 128MB */ +#define CFG_SDRAM_BANKS (2) + /*----------------------------------------------------------------------- * I2C @@ -131,44 +137,70 @@ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F - -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ -#undef CFG_ENV_IS_IN_NVRAM /*No NVRAM on board*/ -#undef CFG_ENV_IS_IN_FLASH /* ... not in flash */ -#define CFG_ENV_IS_IN_EEPROM 1 - -/* Define to allow the user to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - #define CFG_I2C_MULTI_EEPROMS -#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */ -#define CFG_ENV_OFFSET 0x0 #define CFG_I2C_EEPROM_ADDR (0xa8>>1) #define CFG_I2C_EEPROM_ADDR_LEN 1 #define CFG_EEPROM_PAGE_WRITE_ENABLE #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_BOOTCOMMAND "bootm 0xfe000000" /* autoboot command */ -#define CONFIG_BOOTDELAY 3 /* disable autoboot */ +#ifdef CFG_ENV_IS_IN_EEPROM +#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */ +#define CFG_ENV_OFFSET 0x0 +#endif /* CFG_ENV_IS_IN_EEPROM */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "hostname=yosemite\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath)\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ + ":$(hostname):$(netdev):off panic=1\0" \ + "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm $(kernel_addr)\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm $(kernel_addr) $(ramdisk_addr)\0" \ + "net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \ + "bootm\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ + "bootfile=/tftpboot/yosemite/uImage\0" \ + "kernel_addr=fc000000\0" \ + "ramdisk_addr=fc100000\0" \ + "load=tftp 100000 /tftpboot/yosemite/u-boot.bin\0" \ + "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \ + "cp.b 100000 fff80000 80000;" \ + "setenv filesize;saveenv\0" \ + "upd=run load;run update\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_NET_MULTI 1 /* required for netconsole */ -#define CONFIG_PHY1_ADDR 3 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_NET_MULTI 1 /* required for netconsole */ +#define CONFIG_PHY1_ADDR 3 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_IPADDR 10.0.4.251 -#define CONFIG_ETHADDR 00:10:EC:00:12:34 -#define CONFIG_ETH1ADDR 00:10:EC:00:12:35 #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ -#define CONFIG_SERVERIP 10.0.4.115 /* Partitions */ #define CONFIG_MAC_PARTITION @@ -190,53 +222,21 @@ #define CONFIG_HW_WATCHDOG /* watchdog */ #endif -#ifdef CONFIG_440EP - /* Need to define POST */ -#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | \ - CFG_CMD_DATE | \ - CFG_CMD_DHCP | \ - CFG_CMD_DIAG | \ - CFG_CMD_ECHO | \ - CFG_CMD_EEPROM | \ - CFG_CMD_ELF | \ - /* CFG_CMD_EXT2 |*/ \ - /* CFG_CMD_FAT |*/ \ - CFG_CMD_I2C | \ - /* CFG_CMD_IDE |*/ \ - CFG_CMD_IRQ | \ - /* CFG_CMD_KGDB |*/ \ - CFG_CMD_MII | \ - CFG_CMD_PCI | \ - CFG_CMD_PING | \ - CFG_CMD_REGINFO | \ - CFG_CMD_SDRAM | \ - CFG_CMD_FLASH | \ - /* CFG_CMD_SPI |*/ \ - CFG_CMD_USB | \ - 0 ) & ~CFG_CMD_IMLS) -#else -#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | \ - CFG_CMD_DATE | \ - CFG_CMD_DHCP | \ - CFG_CMD_DIAG | \ - CFG_CMD_ECHO | \ - CFG_CMD_EEPROM | \ - CFG_CMD_ELF | \ - /* CFG_CMD_EXT2 |*/ \ - /* CFG_CMD_FAT |*/ \ - CFG_CMD_I2C | \ - /* CFG_CMD_IDE |*/ \ - CFG_CMD_IRQ | \ - /* CFG_CMD_KGDB |*/ \ - CFG_CMD_MII | \ - CFG_CMD_PCI | \ - CFG_CMD_PING | \ - CFG_CMD_REGINFO | \ - CFG_CMD_SDRAM | \ - CFG_CMD_FLASH | \ - /* CFG_CMD_SPI |*/ \ - 0 ) & ~CFG_CMD_IMLS) -#endif +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DHCP | \ + CFG_CMD_DIAG | \ + CFG_CMD_ELF | \ + CFG_CMD_I2C | \ + CFG_CMD_IRQ | \ + CFG_CMD_MII | \ + CFG_CMD_NET | \ + CFG_CMD_NFS | \ + CFG_CMD_PCI | \ + CFG_CMD_PING | \ + CFG_CMD_REGINFO | \ + CFG_CMD_SDRAM | \ + CFG_CMD_USB ) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include @@ -245,42 +245,42 @@ * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CONFIG_LYNXKDI 1 /* support kdi files */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_LYNXKDI 1 /* support kdi files */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ /* General PCI */ -#define CONFIG_PCI /* include pci support */ -#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ +#define CONFIG_PCI /* include pci support */ +#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/ /* Board-specific PCI */ -#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ +#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ #define CFG_PCI_TARGET_INIT #define CFG_PCI_MASTER_INIT -#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ -#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ +#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ /* * For booting Linux, the board info and command line data @@ -288,10 +288,11 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_DCACHE_SIZE 8192 /* For IBM 405 CPUs */ +#define CFG_DCACHE_SIZE (32<<10) /* For IBM 440 CPUs */ #define CFG_CACHELINE_SIZE 32 /* ... */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ @@ -309,4 +310,5 @@ #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif + #endif /* __CONFIG_H */ -- cgit v1.2.3