Merge tag 'mmc-updates-for-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc

Pull MMC updates from Chris Ball:
 "MMC highlights for 3.11:

  Core:
   - Add support for eMMC 5.1 devices
   - Add MMC_CAP_AGGRESSIVE_PM capability for aggressive power
     management of eMMC/SD between requests, using runtime PM
   - Add an ioctl to perform the eMMC 4.5 Sanitize command.  Sample code
     at:

       git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git

  Drivers:
   - dw_mmc: Add support for Rockchip's Cortex-A9 SoCs
   - dw_mmc: Add support for Altera SoCFPGAs
   - sdhci-esdhc-imx: Add support for 8-bit bus width, non-removable
     cards
   - sdhci-bcm-kona: New driver for Broadcom Kona (281xx) SoCs
   - sdhi/tmio: Add DT DMA support"

* tag 'mmc-updates-for-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (87 commits)
  mmc: bcm281xx SDHCI driver
  mmc: sdhci: add card_event callback to sdhci
  mmc: core: Fixup Oops for SDIO shutdown
  mmc: sdhci-pci: add another device id
  mmc: esdhc: Fix bug when writing to SDHCI_HOST_CONTROL register
  mmc: esdhc: Add support for 8-bit bus width and non-removable card
  mmc: core: production year for eMMC 4.41 and later
  mmc: omap: remove unnecessary #if 0's
  mmc: sdhci: fix ctrl_2 on super-speed selection
  mmc: dw_mmc-pltfm: add Rockchip variant
  mmc: dw_mmc-pltfm: move probe and remove below dt match table
  mmc: dw_mmc-pltfm: remove static from dw_mci_pltfm_remove
  mmc: sdhci-acpi: add support for eMMC hardware reset for HID 80860F14
  mmc: sdhci-pci: add support for eMMC hardware reset for BYT eMMC.
  mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
  mmc: sdhci: fix caps2 for HS200
  sdhci-pxav3: Fix runtime PM initialization
  mmc: core: Add DT-bindings for MMC_CAP2_FULL_PWR_CYCLE
  mmc: core: Invent MMC_CAP2_FULL_PWR_CYCLE
  mmc: core: Enable power_off_notify for eMMC shutdown sequence
  ...

1 files changed, 20 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
index 1180d7814af8..cdcebea9c6f5 100644
--- a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt
@@ -39,6 +39,19 @@ Required Properties:
 
 Optional properties:
 
+* clocks: from common clock binding: handle to biu and ciu clocks for the
+  bus interface unit clock and the card interface unit clock.
+
+* clock-names: from common clock binding: Shall be "biu" and "ciu".
+  If the biu clock is missing we'll simply skip enabling it.  If the
+  ciu clock is missing we'll just assume that the clock is running at
+  clock-frequency.  It is an error to omit both the ciu clock and the
+  clock-frequency.
+
+* clock-frequency: should be the frequency (in Hz) of the ciu clock.  If this
+  is specified and the ciu clock is specified then we'll try to set the ciu
+  clock to this at probe time.
+
 * num-slots: specifies the number of slots supported by the controller.
   The number of physical slots actually used could be equal or less than the
   value specified by num-slots. If this property is not specified, the value
@@ -55,6 +68,9 @@ Optional properties:
 
 * broken-cd: as documented in mmc core bindings.
 
+* vmmc-supply: The phandle to the regulator to use for vmmc.  If this is
+  specified we'll defer probe until we can find this regulator.
+
 Aliases:
 
 - All the MSHC controller nodes should be represented in the aliases node using
@@ -67,6 +83,8 @@ board specific portions as listed below.
 
 	dwmmc0@12200000 {
 		compatible = "snps,dw-mshc";
+		clocks = <&clock 351>, <&clock 132>;
+		clock-names = "biu", "ciu";
 		reg = <0x12200000 0x1000>;
 		interrupts = <0 75 0>;
 		#address-cells = <1>;
@@ -74,11 +92,13 @@ board specific portions as listed below.
 	};
 
 	dwmmc0@12200000 {
+		clock-frequency = <400000000>;
 		num-slots = <1>;
 		supports-highspeed;
 		broken-cd;
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
+		vmmc-supply = <&buck8>;
 
 		slot@0 {
 			reg = <0>;