Merge remote branch 'intel/drm-intel-next' of ../drm-next into drm-core-next

* 'intel/drm-intel-next' of ../drm-next: (755 commits)
  drm/i915: Only wait on a pending flip if we intend to write to the buffer
  drm/i915/dp: Sanity check eDP existence
  drm/i915: Rebind the buffer if its alignment constraints changes with tiling
  drm/i915: Disable GPU semaphores by default
  drm/i915: Do not overflow the MMADDR write FIFO
  Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
  drm/i915: Don't save/restore hardware status page address register
  drm/i915: don't store the reg value for HWS_PGA
  drm/i915: fix memory corruption with GM965 and >4GB RAM
  Linux 2.6.38-rc7
  Revert "TPM: Long default timeout fix"
  drm/i915: Re-enable GPU semaphores for SandyBridge mobile
  drm/i915: Replace vblank PM QoS with "Interrupt-Based AGPBUSY#"
  Revert "drm/i915: Use PM QoS to prevent C-State starvation of gen3 GPU"
  drm/i915: Allow relocation deltas outside of target bo
  drm/i915: Silence an innocuous compiler warning for an unused variable
  fs/block_dev.c: fix new kernel-doc warning
  ACPI: Fix build for CONFIG_NET unset
  mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
  x86: Use u32 instead of long to set reset vector back to 0
  ...

Conflicts:
	drivers/gpu/drm/i915/i915_gem.c

1 files changed, 76 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
new file mode 100644
index 000000000000..edb7ae19e868
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
@@ -0,0 +1,76 @@
+* MDIO IO device
+
+The MDIO is a bus to which the PHY devices are connected.  For each
+device that exists on this bus, a child node should be created.  See
+the definition of the PHY node in booting-without-of.txt for an example
+of how to define a PHY.
+
+Required properties:
+  - reg : Offset and length of the register set for the device
+  - compatible : Should define the compatible device type for the
+    mdio.  Currently, this is most likely to be "fsl,gianfar-mdio"
+
+Example:
+
+	mdio@24520 {
+		reg = <24520 20>;
+		compatible = "fsl,gianfar-mdio";
+
+		ethernet-phy@0 {
+			......
+		};
+	};
+
+* TBI Internal MDIO bus
+
+As of this writing, every tsec is associated with an internal TBI PHY.
+This PHY is accessed through the local MDIO bus.  These buses are defined
+similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi".
+The TBI PHYs underneath them are similar to normal PHYs, but the reg property
+is considered instructive, rather than descriptive.  The reg property should
+be chosen so it doesn't interfere with other PHYs on the bus.
+
+* Gianfar-compatible ethernet nodes
+
+Properties:
+
+  - device_type : Should be "network"
+  - model : Model of the device.  Can be "TSEC", "eTSEC", or "FEC"
+  - compatible : Should be "gianfar"
+  - reg : Offset and length of the register set for the device
+  - local-mac-address : List of bytes representing the ethernet address of
+    this controller
+  - interrupts : For FEC devices, the first interrupt is the device's
+    interrupt.  For TSEC and eTSEC devices, the first interrupt is
+    transmit, the second is receive, and the third is error.
+  - phy-handle : The phandle for the PHY connected to this ethernet
+    controller.
+  - fixed-link : <a b c d e> where a is emulated phy id - choose any,
+    but unique to the all specified fixed-links, b is duplex - 0 half,
+    1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no
+    pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause.
+  - phy-connection-type : a string naming the controller/PHY interface type,
+    i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii",
+    "tbi", or "rtbi".  This property is only really needed if the connection
+    is of type "rgmii-id", as all other connection types are detected by
+    hardware.
+  - fsl,magic-packet : If present, indicates that the hardware supports
+    waking up via magic packet.
+  - bd-stash : If present, indicates that the hardware supports stashing
+    buffer descriptors in the L2.
+  - rx-stash-len : Denotes the number of bytes of a received buffer to stash
+    in the L2.
+  - rx-stash-idx : Denotes the index of the first byte from the received
+    buffer to stash in the L2.
+
+Example:
+	ethernet@24000 {
+		device_type = "network";
+		model = "TSEC";
+		compatible = "gianfar";
+		reg = <0x24000 0x1000>;
+		local-mac-address = [ 00 E0 0C 00 73 00 ];
+		interrupts = <29 2 30 2 34 2>;
+		interrupt-parent = <&mpic>;
+		phy-handle = <&phy0>
+	};