Merge tag 'omap-for-v3.14/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards

Split omap3 core padconf area into two as some of the registers in
the padconf area are not accessible and used for other devices.
Also fix the interrupt number for omap2 RNG, and add basic support
for sbc-3xxx with cm-t3730.

Note that the minor merge conflicts for omap_hwmod_2xxx_ipblock_data.c
can be solved by just dropping the legacy hwmod data for interrupts
for v3.14.

* tag 'omap-for-v3.14/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: OMAP2: fix interrupt number for rng
  ARM: dts: Split omap3 pinmux core device
  ARM: dts: Add omap specific pinctrl defines to use padconf addresses
  ARM: dts: Add support for sbc-3xxx with cm-t3730

Signed-off-by: Olof Johansson <olof@lixom.net>

15 files changed, 399 insertions, 67 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 6f527e1faeb6..8cafefa44a7e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -180,6 +180,8 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap2420-n810-wimax.dtb \
 	omap3430-sdp.dtb \
 	omap3-beagle.dtb \
+	omap3-cm-t3730.dtb \
+	omap3-sbc-t3730.dtb \
 	omap3-devkit8000.dtb \
 	omap3-beagle-xm.dtb \
 	omap3-evm.dtb \
diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi
index d0c5b37e248c..5377ddf83bf8 100644
--- a/arch/arm/boot/dts/omap2.dtsi
+++ b/arch/arm/boot/dts/omap2.dtsi
@@ -145,7 +145,7 @@
 			compatible = "ti,omap2-rng";
 			ti,hwmods = "rng";
 			reg = <0x480a0000 0x50>;
-			interrupts = <36>;
+			interrupts = <52>;
 		};
 
 		sham: sham@480a4000 {
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index df33a50bc070..447e714d435b 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -99,7 +99,7 @@
 &omap3_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
-			&hsusbb2_pins
+			&hsusb2_pins
 	>;
 
 	uart3_pins: pinmux_uart3_pins {
@@ -109,20 +109,32 @@
 		>;
 	};
 
-	hsusbb2_pins: pinmux_hsusbb2_pins {
+	hsusb2_pins: pinmux_hsusb2_pins {
 		pinctrl-single,pins = <
-			0x5c0 (PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
-			0x5c2 (PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
-			0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
-			0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
-			0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
-			0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
-			0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
-			0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
-			0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
-			0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
-			0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
-			0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
+			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
+			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
+			OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
+			OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
+			OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
+			OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
+		>;
+	};
+};
+
+&omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&hsusb2_2_pins
+	>;
+
+	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
+			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
+			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
+			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
+			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
+			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
 		>;
 	};
 };
diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index 3ba4a625ea5b..5053766d369b 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -93,23 +93,17 @@
 &omap3_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
-			&hsusbb2_pins
+			&hsusb2_pins
 	>;
 
-	hsusbb2_pins: pinmux_hsusbb2_pins {
+	hsusb2_pins: pinmux_hsusb2_pins {
 		pinctrl-single,pins = <
-			0x5c0 (PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
-			0x5c2 (PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
-			0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
-			0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
-			0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
-			0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
-			0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
-			0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
-			0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
-			0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
-			0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
-			0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
+			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
+			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
+			OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
+			OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
+			OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
+			OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
 		>;
 	};
 
@@ -121,6 +115,24 @@
 	};
 };
 
+&omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&hsusb2_2_pins
+	>;
+
+	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+		pinctrl-single,pins = <
+			OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
+			OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
+			OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
+			OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
+			OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
+			OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
+		>;
+	};
+};
+
 &i2c1 {
 	clock-frequency = <2600000>;
 
diff --git a/arch/arm/boot/dts/omap3-cm-t3730.dts b/arch/arm/boot/dts/omap3-cm-t3730.dts
new file mode 100644
index 000000000000..486f4d6c4219
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-cm-t3730.dts
@@ -0,0 +1,104 @@
+/*
+ * Support for CompuLab CM-T3730
+ */
+/dts-v1/;
+
+#include "omap36xx.dtsi"
+#include "omap3-cm-t3x30.dtsi"
+
+/ {
+	model = "CompuLab CM-T3730";
+	compatible = "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3";
+
+	wl12xx_vmmc2: wl12xx_vmmc2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vw1271";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wl12xx_gpio>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio3 9 GPIO_ACTIVE_HIGH>;   /* gpio73 */
+		startup-delay-us = <20000>;
+		enable-active-high;
+	};
+
+	wl12xx_vaux2: wl12xx_vaux2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271_vaux2";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vaux2>;
+	};
+};
+
+&omap3_pmx_core {
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
+			0x116 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
+			0x118 (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat0.sdmmc1_dat0 */
+			0x11a (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat1.sdmmc1_dat1 */
+			0x11c (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat2.sdmmc1_dat2 */
+			0x11e (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat3.sdmmc1_dat3 */
+		>;
+	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			0x128 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
+			0x12a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
+			0x12c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
+			0x12e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
+			0x130 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
+			0x132 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
+		>;
+	};
+
+	smsc1_pins: pinmux_smsc1_pins {
+		pinctrl-single,pins = <
+			0x88 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs5.gpmc_ncs5 */
+			0x16a (PIN_INPUT_PULLUP | MUX_MODE4)	/* uart3_cts_rctx.gpio_163 */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x16e (PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx.uart3_rx_irrx */
+			0x170 (PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
+		>;
+	};
+
+	wl12xx_gpio: pinmux_wl12xx_gpio {
+		pinctrl-single,pins = <
+			0xb2 (PIN_OUTPUT | MUX_MODE4)		/* dss_data3.gpio_73 */
+			0x134 (PIN_INPUT | MUX_MODE4)		/* sdmmc2_dat4.gpio_136 */
+		>;
+	};
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmc1>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&wl12xx_vmmc2>;
+	vmmc_aux-supply = <&wl12xx_vaux2>;
+	non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+};
+
+&smsc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&smsc1_pins>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
diff --git a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
new file mode 100644
index 000000000000..3a9f004d8924
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
@@ -0,0 +1,95 @@
+/*
+ * Common support for CompuLab CM-T3530 and  CM-T3730
+ */
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vcc>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		ledb {
+			label = "cm-t35:green";
+			gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>;  /* gpio186 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	vddvario: regulator-vddvario {
+		compatible = "regulator-fixed";
+		regulator-name = "vddvario";
+		regulator-always-on;
+	};
+
+	vdd33a: regulator-vdd33a {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd33a";
+		regulator-always-on;
+	};
+};
+
+&gpmc {
+	ranges = <5 0 0x2c000000 0x01000000>;
+
+	smsc1: ethernet@5,0 {
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		interrupt-parent = <&gpio6>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		reg = <5 0 0xff>;
+		bank-width = <2>;
+		gpmc,mux-add-data;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <186>;
+		gpmc,cs-wr-off-ns = <186>;
+		gpmc,adv-on-ns = <12>;
+		gpmc,adv-rd-off-ns = <48>;
+		gpmc,adv-wr-off-ns = <48>;
+		gpmc,oe-on-ns = <54>;
+		gpmc,oe-off-ns = <168>;
+		gpmc,we-on-ns = <54>;
+		gpmc,we-off-ns = <168>;
+		gpmc,rd-cycle-ns = <186>;
+		gpmc,wr-cycle-ns = <186>;
+		gpmc,access-ns = <114>;
+		gpmc,page-burst-access-ns = <6>;
+		gpmc,bus-turnaround-ns = <12>;
+		gpmc,cycle2cycle-delay-ns = <18>;
+		gpmc,wr-data-mux-bus-ns = <90>;
+		gpmc,wr-access-ns = <186>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+		vddvario-supply = <&vddvario>;
+		vdd33a-supply = <&vdd33a>;
+		reg-io-width = <4>;
+		smsc,save-mac-address;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+	};
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&i2c3 {
+	clock-frequency = <400000>;
+};
+
+&twl_gpio {
+	ti,use-leds;
+};
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi
index 165aaf7591ba..c17009323520 100644
--- a/arch/arm/boot/dts/omap3-igep.dtsi
+++ b/arch/arm/boot/dts/omap3-igep.dtsi
@@ -133,8 +133,6 @@
 			0x194 (PIN_INPUT | MUX_MODE0)   /* i2c3_sda.i2c3_sda */
 		>;
 	};
-
-	leds_pins: pinmux_leds_pins { };
 };
 
 &i2c1 {
diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts
index 1c7e74d2d2bc..25a2b5f652fd 100644
--- a/arch/arm/boot/dts/omap3-igep0020.dts
+++ b/arch/arm/boot/dts/omap3-igep0020.dts
@@ -66,28 +66,10 @@
 &omap3_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
-		&hsusbb1_pins
 		&tfp410_pins
 		&dss_pins
 	>;
 
-	hsusbb1_pins: pinmux_hsusbb1_pins {
-		pinctrl-single,pins = <
-			0x5aa (PIN_OUTPUT | MUX_MODE3)		/* etk_ctl.hsusb1_clk */
-			0x5a8 (PIN_OUTPUT | MUX_MODE3)		/* etk_clk.hsusb1_stp */
-			0x5bc (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d8.hsusb1_dir */
-			0x5be (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d9.hsusb1_nxt */
-			0x5ac (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d0.hsusb1_data0 */
-			0x5ae (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d1.hsusb1_data1 */
-			0x5b0 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d2.hsusb1_data2 */
-			0x5b2 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d3.hsusb1_data7 */
-			0x5b4 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d4.hsusb1_data4 */
-			0x5b6 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d5.hsusb1_data5 */
-			0x5b8 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d6.hsusb1_data6 */
-			0x5ba (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d7.hsusb1_data3 */
-		>;
-	};
-
 	tfp410_pins: tfp410_dvi_pins {
 		pinctrl-single,pins = <
 			0x196 (PIN_OUTPUT | MUX_MODE4)   /* hdq_sio.gpio_170 */
@@ -128,12 +110,36 @@
 	};
 };
 
-&leds_pins {
-	pinctrl-single,pins = <
-		0x5c4 (PIN_OUTPUT | MUX_MODE4) /* etk_d12.gpio_26 */
-		0x5c6 (PIN_OUTPUT | MUX_MODE4) /* etk_d13.gpio_27 */
-		0x5c8 (PIN_OUTPUT | MUX_MODE4) /* etk_d14.gpio_28 */
+&omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&hsusbb1_pins
 	>;
+
+	hsusbb1_pins: pinmux_hsusbb1_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25da, PIN_OUTPUT | MUX_MODE3)		/* etk_ctl.hsusb1_clk */
+			OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE3)		/* etk_clk.hsusb1_stp */
+			OMAP3630_CORE2_IOPAD(0x25ec, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d8.hsusb1_dir */
+			OMAP3630_CORE2_IOPAD(0x25ee, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d9.hsusb1_nxt */
+			OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d0.hsusb1_data0 */
+			OMAP3630_CORE2_IOPAD(0x25de, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d1.hsusb1_data1 */
+			OMAP3630_CORE2_IOPAD(0x25e0, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d2.hsusb1_data2 */
+			OMAP3630_CORE2_IOPAD(0x25e2, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d3.hsusb1_data7 */
+			OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d4.hsusb1_data4 */
+			OMAP3630_CORE2_IOPAD(0x25e6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d5.hsusb1_data5 */
+			OMAP3630_CORE2_IOPAD(0x25e8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d6.hsusb1_data6 */
+			OMAP3630_CORE2_IOPAD(0x25ea, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d7.hsusb1_data3 */
+		>;
+	};
+
+	leds_pins: pinmux_leds_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25f4, PIN_OUTPUT | MUX_MODE4) /* etk_d12.gpio_26 */
+			OMAP3630_CORE2_IOPAD(0x25f6, PIN_OUTPUT | MUX_MODE4) /* etk_d13.gpio_27 */
+			OMAP3630_CORE2_IOPAD(0x25f8, PIN_OUTPUT | MUX_MODE4) /* etk_d14.gpio_28 */
+		>;
+	};
 };
 
 &i2c3 {
diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts
index 02a23f8a3384..145c58cfc8ac 100644
--- a/arch/arm/boot/dts/omap3-igep0030.dts
+++ b/arch/arm/boot/dts/omap3-igep0030.dts
@@ -46,10 +46,12 @@
 	};
 };
 
-&leds_pins {
-	pinctrl-single,pins = <
-		0x5b0 (PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */
-	>;
+&omap3_pmx_core2 {
+	leds_pins: pinmux_leds_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */
+		>;
+	};
 };
 
 &gpmc {
diff --git a/arch/arm/boot/dts/omap3-sb-t35.dtsi b/arch/arm/boot/dts/omap3-sb-t35.dtsi
new file mode 100644
index 000000000000..b9a2fedce7ee
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-sb-t35.dtsi
@@ -0,0 +1,40 @@
+/*
+ * Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730
+ */
+
+&gpmc {
+	ranges = <4 0 0x2d000000 0x01000000>;
+
+	smsc2: ethernet@4,0 {
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		interrupt-parent = <&gpio3>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+		reg = <4 0 0xff>;
+		bank-width = <2>;
+		gpmc,mux-add-data;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <186>;
+		gpmc,cs-wr-off-ns = <186>;
+		gpmc,adv-on-ns = <12>;
+		gpmc,adv-rd-off-ns = <48>;
+		gpmc,adv-wr-off-ns = <48>;
+		gpmc,oe-on-ns = <54>;
+		gpmc,oe-off-ns = <168>;
+		gpmc,we-on-ns = <54>;
+		gpmc,we-off-ns = <168>;
+		gpmc,rd-cycle-ns = <186>;
+		gpmc,wr-cycle-ns = <186>;
+		gpmc,access-ns = <114>;
+		gpmc,page-burst-access-ns = <6>;
+		gpmc,bus-turnaround-ns = <12>;
+		gpmc,cycle2cycle-delay-ns = <18>;
+		gpmc,wr-data-mux-bus-ns = <90>;
+		gpmc,wr-access-ns = <186>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+		vddvario-supply = <&vddvario>;
+		vdd33a-supply = <&vdd33a>;
+		reg-io-width = <4>;
+		smsc,save-mac-address;
+	};
+};
diff --git a/arch/arm/boot/dts/omap3-sbc-t3730.dts b/arch/arm/boot/dts/omap3-sbc-t3730.dts
new file mode 100644
index 000000000000..c119bd545053
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-sbc-t3730.dts
@@ -0,0 +1,30 @@
+/*
+ * Suppport for CompuLab SBC-T3730 with CM-T3730
+ */
+
+#include "omap3-cm-t3730.dts"
+#include "omap3-sb-t35.dtsi"
+
+/ {
+	model = "CompuLab SBC-T3730 with CM-T3730";
+	compatible = "compulab,omap3-sbc-t3730", "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3";
+};
+
+&gpmc {
+	ranges = <5 0 0x2c000000 0x01000000>,
+		 <4 0 0x2d000000 0x01000000>;
+};
+
+&smsc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&smsc2_pins>;
+};
+
+&omap3_pmx_core {
+	smsc2_pins: pinmux_smsc2_pins {
+		pinctrl-single,pins = <
+			0x86 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs4.gpmc_ncs4 */
+			0xa2 (PIN_INPUT_PULLUP | MUX_MODE4)	/* gpmc_wait3.gpio_65 */
+		>;
+	};
+};
\ No newline at end of file
diff --git a/arch/arm/boot/dts/omap3-zoom3.dts b/arch/arm/boot/dts/omap3-zoom3.dts
index 15eb9fe5169c..6644f516a42b 100644
--- a/arch/arm/boot/dts/omap3-zoom3.dts
+++ b/arch/arm/boot/dts/omap3-zoom3.dts
@@ -80,13 +80,8 @@
 
 	mmc3_pins: pinmux_mmc3_pins {
 		pinctrl-single,pins = <
-			0x168 (PIN_INPUT | MUX_MODE4)	/* mcbsp1_clkx.gpio_162 WLAN IRQ */
-			0x1a0 (PIN_INPUT_PULLUP | MUX_MODE3)	/* mcspi1_cs1.sdmmc3_cmd */
-			0x5a8 (PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_clk.sdmmc3_clk */
-			0x5b4 (PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d4.sdmmc3_dat0 */
-			0x5b6 (WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d5.sdmmc3_dat1 */
-			0x5b8 (PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d6.sdmmc3_dat2 */
-			0x5b2 (PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d3.sdmmc3_dat3 */
+			OMAP3_CORE1_IOPAD(0x2198, PIN_INPUT | MUX_MODE4)	/* mcbsp1_clkx.gpio_162 WLAN IRQ */
+			OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3)	/* mcspi1_cs1.sdmmc3_cmd */
 		>;
 	};
 
@@ -125,6 +120,18 @@
 	};
 };
 
+&omap3_pmx_core2 {
+	mmc3_2_pins: pinmux_mmc3_2_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_clk.sdmmc3_clk */
+			OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d4.sdmmc3_dat0 */
+			OMAP3630_CORE2_IOPAD(0x25e6, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d5.sdmmc3_dat1 */
+			OMAP3630_CORE2_IOPAD(0x25e8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d6.sdmmc3_dat2 */
+			OMAP3630_CORE2_IOPAD(0x25e2, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d3.sdmmc3_dat3 */
+		>;
+	};
+};
+
 &omap3_pmx_wkup {
 	wlan_host_wkup: pinmux_wlan_host_wkup_pins {
 		pinctrl-single,pins = <
@@ -187,7 +194,7 @@
 	bus-width = <4>;
 	cap-power-off-card;
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc3_pins>;
+	pinctrl-0 = <&mmc3_pins &mmc3_2_pins>;
 };
 
 &uart1 {
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index daabf99d402a..427395c083f5 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -117,7 +117,7 @@
 
 		omap3_pmx_core: pinmux@48002030 {
 			compatible = "ti,omap3-padconf", "pinctrl-single";
-			reg = <0x48002030 0x05cc>;
+			reg = <0x48002030 0x0238>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			#interrupt-cells = <1>;
diff --git a/arch/arm/boot/dts/omap34xx.dtsi b/arch/arm/boot/dts/omap34xx.dtsi
index 5355d6173748..77d124678c95 100644
--- a/arch/arm/boot/dts/omap34xx.dtsi
+++ b/arch/arm/boot/dts/omap34xx.dtsi
@@ -25,4 +25,17 @@
 			clock-latency = <300000>; /* From legacy driver */
 		};
 	};
+
+	ocp {
+		omap3_pmx_core2: pinmux@480025d8 {
+			compatible = "ti,omap3-padconf", "pinctrl-single";
+			reg = <0x480025d8 0x24>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			pinctrl-single,register-width = <16>;
+			pinctrl-single,function-mask = <0xff1f>;
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi
index 380c22eb468e..b7c7bd96c404 100644
--- a/arch/arm/boot/dts/omap36xx.dtsi
+++ b/arch/arm/boot/dts/omap36xx.dtsi
@@ -38,5 +38,16 @@
 			ti,hwmods = "uart4";
 			clock-frequency = <48000000>;
 		};
+
+		omap3_pmx_core2: pinmux@480025a0 {
+			compatible = "ti,omap3-padconf", "pinctrl-single";
+			reg = <0x480025a0 0x5c>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			pinctrl-single,register-width = <16>;
+			pinctrl-single,function-mask = <0xff1f>;
+		};
 	};
 };