OMAP: DMA: Convert DMA library into platform driver

Convert DMA library into DMA platform driver and make use of
platform data provided by hwmod data base for OMAP2+ onwards.

For OMAP1 processors, the DMA driver in mach-omap uses resource
structures for getting platform data.

Thanks to Tony Lindgren <tony@atomide.com> for fixing various
omap1 issues and testing the same on OSK5912 board.

Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

1 files changed, 223 insertions, 0 deletions

diff --git a/arch/arm/mach-omap2/dma.c b/arch/arm/mach-omap2/dma.c
index 2130059e98cb..d2f15f5cfd36 100644
--- a/arch/arm/mach-omap2/dma.c
+++ b/arch/arm/mach-omap2/dma.c
@@ -32,6 +32,61 @@
 #include <plat/omap_device.h>
 #include <plat/dma.h>
 
+#define OMAP2_DMA_STRIDE	0x60
+
+static u32 errata;
+static u8 dma_stride;
+
+static struct omap_dma_dev_attr *d;
+
+static enum omap_reg_offsets dma_common_ch_start, dma_common_ch_end;
+
+static u16 reg_map[] = {
+	[REVISION]		= 0x00,
+	[GCR]			= 0x78,
+	[IRQSTATUS_L0]		= 0x08,
+	[IRQSTATUS_L1]		= 0x0c,
+	[IRQSTATUS_L2]		= 0x10,
+	[IRQSTATUS_L3]		= 0x14,
+	[IRQENABLE_L0]		= 0x18,
+	[IRQENABLE_L1]		= 0x1c,
+	[IRQENABLE_L2]		= 0x20,
+	[IRQENABLE_L3]		= 0x24,
+	[SYSSTATUS]		= 0x28,
+	[OCP_SYSCONFIG]		= 0x2c,
+	[CAPS_0]		= 0x64,
+	[CAPS_2]		= 0x6c,
+	[CAPS_3]		= 0x70,
+	[CAPS_4]		= 0x74,
+
+	/* Common register offsets */
+	[CCR]			= 0x80,
+	[CLNK_CTRL]		= 0x84,
+	[CICR]			= 0x88,
+	[CSR]			= 0x8c,
+	[CSDP]			= 0x90,
+	[CEN]			= 0x94,
+	[CFN]			= 0x98,
+	[CSEI]			= 0xa4,
+	[CSFI]			= 0xa8,
+	[CDEI]			= 0xac,
+	[CDFI]			= 0xb0,
+	[CSAC]			= 0xb4,
+	[CDAC]			= 0xb8,
+
+	/* Channel specific register offsets */
+	[CSSA]			= 0x9c,
+	[CDSA]			= 0xa0,
+	[CCEN]			= 0xbc,
+	[CCFN]			= 0xc0,
+	[COLOR]			= 0xc4,
+
+	/* OMAP4 specific registers */
+	[CDP]			= 0xd0,
+	[CNDP]			= 0xd4,
+	[CCDN]			= 0xd8,
+};
+
 static struct omap_device_pm_latency omap2_dma_latency[] = {
 	{
 		.deactivate_func = omap_device_idle_hwmods,
@@ -40,13 +95,151 @@ static struct omap_device_pm_latency omap2_dma_latency[] = {
 	},
 };
 
+static void __iomem *dma_base;
+static inline void dma_write(u32 val, int reg, int lch)
+{
+	u8  stride;
+	u32 offset;
+
+	stride = (reg >= dma_common_ch_start) ? dma_stride : 0;
+	offset = reg_map[reg] + (stride * lch);
+	__raw_writel(val, dma_base + offset);
+}
+
+static inline u32 dma_read(int reg, int lch)
+{
+	u8 stride;
+	u32 offset, val;
+
+	stride = (reg >= dma_common_ch_start) ? dma_stride : 0;
+	offset = reg_map[reg] + (stride * lch);
+	val = __raw_readl(dma_base + offset);
+	return val;
+}
+
+static inline void omap2_disable_irq_lch(int lch)
+{
+	u32 val;
+
+	val = dma_read(IRQENABLE_L0, lch);
+	val &= ~(1 << lch);
+	dma_write(val, IRQENABLE_L0, lch);
+}
+
+static void omap2_clear_dma(int lch)
+{
+	int i = dma_common_ch_start;
+
+	for (; i <= dma_common_ch_end; i += 1)
+		dma_write(0, i, lch);
+}
+
+static void omap2_show_dma_caps(void)
+{
+	u8 revision = dma_read(REVISION, 0) & 0xff;
+	printk(KERN_INFO "OMAP DMA hardware revision %d.%d\n",
+				revision >> 4, revision & 0xf);
+	return;
+}
+
+static u32 configure_dma_errata(void)
+{
+
+	/*
+	 * Errata applicable for OMAP2430ES1.0 and all omap2420
+	 *
+	 * I.
+	 * Erratum ID: Not Available
+	 * Inter Frame DMA buffering issue DMA will wrongly
+	 * buffer elements if packing and bursting is enabled. This might
+	 * result in data gets stalled in FIFO at the end of the block.
+	 * Workaround: DMA channels must have BUFFERING_DISABLED bit set to
+	 * guarantee no data will stay in the DMA FIFO in case inter frame
+	 * buffering occurs
+	 *
+	 * II.
+	 * Erratum ID: Not Available
+	 * DMA may hang when several channels are used in parallel
+	 * In the following configuration, DMA channel hanging can occur:
+	 * a. Channel i, hardware synchronized, is enabled
+	 * b. Another channel (Channel x), software synchronized, is enabled.
+	 * c. Channel i is disabled before end of transfer
+	 * d. Channel i is reenabled.
+	 * e. Steps 1 to 4 are repeated a certain number of times.
+	 * f. A third channel (Channel y), software synchronized, is enabled.
+	 * Channel x and Channel y may hang immediately after step 'f'.
+	 * Workaround:
+	 * For any channel used - make sure NextLCH_ID is set to the value j.
+	 */
+	if (cpu_is_omap2420() || (cpu_is_omap2430() &&
+				(omap_type() == OMAP2430_REV_ES1_0))) {
+
+		SET_DMA_ERRATA(DMA_ERRATA_IFRAME_BUFFERING);
+		SET_DMA_ERRATA(DMA_ERRATA_PARALLEL_CHANNELS);
+	}
+
+	/*
+	 * Erratum ID: i378: OMAP2+: sDMA Channel is not disabled
+	 * after a transaction error.
+	 * Workaround: SW should explicitely disable the channel.
+	 */
+	if (cpu_class_is_omap2())
+		SET_DMA_ERRATA(DMA_ERRATA_i378);
+
+	/*
+	 * Erratum ID: i541: sDMA FIFO draining does not finish
+	 * If sDMA channel is disabled on the fly, sDMA enters standby even
+	 * through FIFO Drain is still in progress
+	 * Workaround: Put sDMA in NoStandby more before a logical channel is
+	 * disabled, then put it back to SmartStandby right after the channel
+	 * finishes FIFO draining.
+	 */
+	if (cpu_is_omap34xx())
+		SET_DMA_ERRATA(DMA_ERRATA_i541);
+
+	/*
+	 * Erratum ID: i88 : Special programming model needed to disable DMA
+	 * before end of block.
+	 * Workaround: software must ensure that the DMA is configured in No
+	 * Standby mode(DMAx_OCP_SYSCONFIG.MIDLEMODE = "01")
+	 */
+	if (omap_type() == OMAP3430_REV_ES1_0)
+		SET_DMA_ERRATA(DMA_ERRATA_i88);
+
+	/*
+	 * Erratum 3.2/3.3: sometimes 0 is returned if CSAC/CDAC is
+	 * read before the DMA controller finished disabling the channel.
+	 */
+	SET_DMA_ERRATA(DMA_ERRATA_3_3);
+
+	/*
+	 * Erratum ID: Not Available
+	 * A bug in ROM code leaves IRQ status for channels 0 and 1 uncleared
+	 * after secure sram context save and restore.
+	 * Work around: Hence we need to manually clear those IRQs to avoid
+	 * spurious interrupts. This affects only secure devices.
+	 */
+	if (cpu_is_omap34xx() && (omap_type() != OMAP2_DEVICE_TYPE_GP))
+		SET_DMA_ERRATA(DMA_ROMCODE_BUG);
+
+	return errata;
+}
+
 /* One time initializations */
 static int __init omap2_system_dma_init_dev(struct omap_hwmod *oh, void *unused)
 {
 	struct omap_device			*od;
 	struct omap_system_dma_plat_info	*p;
+	struct resource				*mem;
 	char					*name = "omap_dma_system";
 
+	dma_stride		= OMAP2_DMA_STRIDE;
+	dma_common_ch_start	= CSDP;
+	if (cpu_is_omap3630() || cpu_is_omap4430())
+		dma_common_ch_end = CCDN;
+	else
+		dma_common_ch_end = CCFN;
+
 	p = kzalloc(sizeof(struct omap_system_dma_plat_info), GFP_KERNEL);
 	if (!p) {
 		pr_err("%s: Unable to allocate pdata for %s:%s\n",
@@ -54,6 +247,17 @@ static int __init omap2_system_dma_init_dev(struct omap_hwmod *oh, void *unused)
 		return -ENOMEM;
 	}
 
+	p->dma_attr		= (struct omap_dma_dev_attr *)oh->dev_attr;
+	p->disable_irq_lch	= omap2_disable_irq_lch;
+	p->show_dma_caps	= omap2_show_dma_caps;
+	p->clear_dma		= omap2_clear_dma;
+	p->dma_write		= dma_write;
+	p->dma_read		= dma_read;
+
+	p->clear_lch_regs	= NULL;
+
+	p->errata		= configure_dma_errata();
+
 	od = omap_device_build(name, 0, oh, p, sizeof(*p),
 			omap2_dma_latency, ARRAY_SIZE(omap2_dma_latency), 0);
 	kfree(p);
@@ -63,6 +267,25 @@ static int __init omap2_system_dma_init_dev(struct omap_hwmod *oh, void *unused)
 		return IS_ERR(od);
 	}
 
+	mem = platform_get_resource(&od->pdev, IORESOURCE_MEM, 0);
+	if (!mem) {
+		dev_err(&od->pdev.dev, "%s: no mem resource\n", __func__);
+		return -EINVAL;
+	}
+	dma_base = ioremap(mem->start, resource_size(mem));
+	if (!dma_base) {
+		dev_err(&od->pdev.dev, "%s: ioremap fail\n", __func__);
+		return -ENOMEM;
+	}
+
+	d = oh->dev_attr;
+	d->chan = kzalloc(sizeof(struct omap_dma_lch) *
+					(d->lch_count), GFP_KERNEL);
+
+	if (!d->chan) {
+		dev_err(&od->pdev.dev, "%s: kzalloc fail\n", __func__);
+		return -ENOMEM;
+	}
 	return 0;
 }