ARM: OMAP2/3: Add generic smc91x support when connected to GPMC

Convert the board-rx51 smc91x code to be generic and make
the boards to use it. This allows future recalculation of the
timings when the source clock gets scaled.

Also correct the rx51 interrupt to be IORESOURCE_IRQ_HIGHLEVEL.

Thanks to Paul Walmsley <paul@pwsan.com> for better GPMC timing
calculations.

Signed-off-by: Tony Lindgren <tony@atomide.com>

1 files changed, 189 insertions, 0 deletions

diff --git a/arch/arm/mach-omap2/gpmc-smc91x.c b/arch/arm/mach-omap2/gpmc-smc91x.c
new file mode 100644
index 000000000000..df99d31d8b64
--- /dev/null
+++ b/arch/arm/mach-omap2/gpmc-smc91x.c
@@ -0,0 +1,189 @@
+/*
+ * linux/arch/arm/mach-omap2/gpmc-smc91x.c
+ *
+ * Copyright (C) 2009 Nokia Corporation
+ * Contact:	Tony Lindgren
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/smc91x.h>
+
+#include <mach/board.h>
+#include <mach/gpmc.h>
+#include <mach/gpmc-smc91x.h>
+
+static struct omap_smc91x_platform_data *gpmc_cfg;
+
+static struct resource gpmc_smc91x_resources[] = {
+	[0] = {
+		.flags		= IORESOURCE_MEM,
+	},
+	[1] = {
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct smc91x_platdata gpmc_smc91x_info = {
+	.flags  = SMC91X_USE_16BIT | SMC91X_NOWAIT | SMC91X_IO_SHIFT_0,
+};
+
+static struct platform_device gpmc_smc91x_device = {
+	.name		= "smc91x",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(gpmc_smc91x_resources),
+	.resource	= gpmc_smc91x_resources,
+	.dev		= {
+		.platform_data = &gpmc_smc91x_info,
+	},
+};
+
+/*
+ * Set the gpmc timings for smc91c96. The timings are taken
+ * from the data sheet available at:
+ * http://www.smsc.com/main/catalog/lan91c96.html
+ * REVISIT: Level shifters can add at least to the access latency.
+ */
+static int smc91c96_gpmc_retime(void)
+{
+	struct gpmc_timings t;
+	const int t3 = 10;	/* Figure 12.2 read and 12.4 write */
+	const int t4_r = 20;	/* Figure 12.2 read */
+	const int t4_w = 5;	/* Figure 12.4 write */
+	const int t5 = 25;	/* Figure 12.2 read */
+	const int t6 = 15;	/* Figure 12.2 read */
+	const int t7 = 5;	/* Figure 12.4 write */
+	const int t8 = 5;	/* Figure 12.4 write */
+	const int t20 = 185;	/* Figure 12.2 read and 12.4 write */
+	u32 l;
+
+	memset(&t, 0, sizeof(t));
+
+	/* Read timings */
+	t.cs_on = 0;
+	t.adv_on = t.cs_on;
+	t.oe_on = t.adv_on + t3;
+	t.access = t.oe_on + t5;
+	t.oe_off = t.access;
+	t.adv_rd_off = t.oe_off + max(t4_r, t6);
+	t.cs_rd_off = t.oe_off;
+	t.rd_cycle = t20 - t.oe_on;
+
+	/* Write timings */
+	t.we_on = t.adv_on + t3;
+
+	if (cpu_is_omap34xx() && (gpmc_cfg->flags & GPMC_MUX_ADD_DATA)) {
+		t.wr_data_mux_bus = t.we_on;
+		t.we_off = t.wr_data_mux_bus + t7;
+	} else
+		t.we_off = t.we_on + t7;
+	if (cpu_is_omap34xx())
+		t.wr_access = t.we_off;
+	t.adv_wr_off = t.we_off + max(t4_w, t8);
+	t.cs_wr_off = t.we_off + t4_w;
+	t.wr_cycle = t20 - t.we_on;
+
+	l = GPMC_CONFIG1_DEVICESIZE_16;
+	if (gpmc_cfg->flags & GPMC_MUX_ADD_DATA)
+		l |= GPMC_CONFIG1_MUXADDDATA;
+	if (gpmc_cfg->flags & GPMC_READ_MON)
+		l |= GPMC_CONFIG1_WAIT_READ_MON;
+	if (gpmc_cfg->flags & GPMC_WRITE_MON)
+		l |= GPMC_CONFIG1_WAIT_WRITE_MON;
+	if (gpmc_cfg->wait_pin)
+		l |= GPMC_CONFIG1_WAIT_PIN_SEL(gpmc_cfg->wait_pin);
+	gpmc_cs_write_reg(gpmc_cfg->cs, GPMC_CS_CONFIG1, l);
+
+	/*
+	 * FIXME: Calculate the address and data bus muxed timings.
+	 * Note that at least adv_rd_off needs to be changed according
+	 * to omap3430 TRM Figure 11-11. Are the sdp boards using the
+	 * FPGA in between smc91x and omap as the timings are different
+	 * from above?
+	 */
+	if (gpmc_cfg->flags & GPMC_MUX_ADD_DATA)
+		return 0;
+
+	return gpmc_cs_set_timings(gpmc_cfg->cs, &t);
+}
+
+/*
+ * Initialize smc91x device connected to the GPMC. Note that we
+ * assume that pin multiplexing is done in the board-*.c file,
+ * or in the bootloader.
+ */
+void __init gpmc_smc91x_init(struct omap_smc91x_platform_data *board_data)
+{
+	unsigned long cs_mem_base;
+	int ret;
+
+	gpmc_cfg = board_data;
+
+	if (gpmc_cfg->flags & GPMC_TIMINGS_SMC91C96)
+		gpmc_cfg->retime = smc91c96_gpmc_retime;
+
+	if (gpmc_cs_request(gpmc_cfg->cs, SZ_16M, &cs_mem_base) < 0) {
+		printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
+		return;
+	}
+
+	gpmc_smc91x_resources[0].start = cs_mem_base + 0x300;
+	gpmc_smc91x_resources[0].end = cs_mem_base + 0x30f;
+	gpmc_smc91x_resources[1].flags |= (gpmc_cfg->flags & IRQF_TRIGGER_MASK);
+
+	if (gpmc_cfg->retime) {
+		ret = gpmc_cfg->retime();
+		if (ret != 0)
+			goto free1;
+	}
+
+	if (gpio_request(gpmc_cfg->gpio_irq, "SMC91X irq") < 0)
+		goto free1;
+
+	gpio_direction_input(gpmc_cfg->gpio_irq);
+	gpmc_smc91x_resources[1].start = gpio_to_irq(gpmc_cfg->gpio_irq);
+
+	if (gpmc_cfg->gpio_pwrdwn) {
+		ret = gpio_request(gpmc_cfg->gpio_pwrdwn, "SMC91X powerdown");
+		if (ret)
+			goto free2;
+		gpio_direction_output(gpmc_cfg->gpio_pwrdwn, 0);
+	}
+
+	if (gpmc_cfg->gpio_reset) {
+		ret = gpio_request(gpmc_cfg->gpio_reset, "SMC91X reset");
+		if (ret)
+			goto free3;
+
+		gpio_direction_output(gpmc_cfg->gpio_reset, 0);
+		gpio_set_value(gpmc_cfg->gpio_reset, 1);
+		msleep(100);
+		gpio_set_value(gpmc_cfg->gpio_reset, 0);
+	}
+
+	if (platform_device_register(&gpmc_smc91x_device) < 0) {
+		printk(KERN_ERR "Unable to register smc91x device\n");
+		gpio_free(gpmc_cfg->gpio_reset);
+		goto free3;
+	}
+
+	return;
+
+free3:
+	if (gpmc_cfg->gpio_pwrdwn)
+		gpio_free(gpmc_cfg->gpio_pwrdwn);
+free2:
+	gpio_free(gpmc_cfg->gpio_irq);
+free1:
+	gpmc_cs_free(gpmc_cfg->cs);
+
+	printk(KERN_ERR "Could not initialize smc91x\n");
+}